Distribution of PM2.5 and PM10-2.5 in PM10 Fraction in Ambient Air Due to Vehicular Pollution in Kolkata Megacity

This research paper aims at establishing baseline PM₁₀ and PM_2.5 concentration levels, which could be effectively used to develop and upgrade the standards in air pollution in developing countries. The relative contribution of fine fractions (PM_2.5) and coarser fractions (PM_10-2.5) to PM₁₀ fractions were investigates in a megacity which is overcrowded and congested due to lack of road network and deteriorated air quality because of vehicular pollution. The present study was carried out during the winter of 2002. The average 24h PM₁₀ concentration was 304 μg/m³, which is 3 times more than the Indian National Ambient Air Quality Standards (NAAQS) and higher PM₁₀ concentration was due to fine fraction (PM_2.5) released by vehicular exhaust. The 24h average PM_2.5 concentration was found 179 μg/m³, which is exceeded USEPA and EU standards of 65 and 50 μg/m³ respectively for the winter. India does not have any PM_2.5 standards. The 24 h average PM_10-2.5 concentrations were found 126 μg/m³. The PM_2.5 constituted more than 59% of PM₁₀ and whereas PM₁₀-PM_2.5 fractions constituted 41% of PM₁₀. The correlation between PM₁₀ and PM_2.5 was found higher as PM_2.5 comprised major proportion of PM₁₀ fractions contributed by vehicular emissions.     

Gravimetric and Chemical Features of Airborne PM10 AND PM2.5 in Mainland Portugal

This paper describes concentration amounts of arsenic (As), particulate mercury (Hg), nickel (Ni) and lead (Pb) in PM₁₀ and PM_2.5, collected since 1993 by the Technological and Nuclear Institute (ITN) at different locations in mainland Portugal, featuring urban, industrial and rural environments, and a control as well. Most results were obtained in the vicinity of coal- and oil-fired power plants. Airborne mass concentrations were determined by gravimetry. As and Hg concentrations were obtained through instrumental neutron activation analysis (INAA), and Ni and Pb concentrations through proton-induced X-ray emission (PIXE). Comparison with the EU (European Union) and the US EPA (United States Environmental Protection Agency) directives for Ambient Air has been carried out, even though the sampling protocols herein – set within the framework of ITN's R&D projects and/or monitoring contracts – were not consistent with the former regulations. Taking this into account, 1) the EU daily limit for PM₁₀ was exceeded a few times in all sites except the control, even if the number of times was still inferior to the allowed one; 2) the EU annual mean for PM₁₀ was exceeded at one site; 3) the EPA daily limit for PM_2.5 was exceeded one time at three sites; 4) the EPA annual mean for PM_2.5 was exceeded at most sites; 5) the inner-Lisboa site approached or exceeded the legislated PMs; 6) Pb levels stayed far below the EU limit value; and 7) concentrations of As, Ni and Hg were also far less than the reference values adopted by EU. In every location, Ni appeared more concentrated in PM_2.5 than in coarser particles, and its levels were not that different from site to site, excluding the control. The highest As and Hg concentrations were found in the neighbourhood of the coal-fired, utility power plants. The results may be viewed as a “worst-case scenario” of atmospheric pollution, since they have been obtained in busy urban-industrial areas and/or near major power-generation and waste-incineration facilities.     

PM2.5 and PM10 Concentrations from the Qalabotjha Low-Smoke Fuels Macro-Scale Experiment in South Africa

This article presents results from the particulate monitoringcampaign conducted at Qalabotjha in South Africa during the winter of 1997. Combustion of D-grade domestic coal and low-smoke fuels were compared in a residential neighborhood to evaluate the extent of air quality improvement by switchinghousehold cooking and heating fuels.Comparisons are drawn between the gravimetric results from the two types of filter substrates (Teflon-membrane and quartz-fiber) as well as between the integrated and continuous samplers. It is demonstrated that the quartz-fiber filters reported 5 to 10% greater particulate mass than the Teflon-membrane filters, mainly due to the adsorption of organic gases onto the quartz-fiber filters. Due to heating of sampling stream to 50 °C in the TEOM continuous sampler and the high volatile content of the samples, approximately 15% of the particulate mass was lost during sampling.The USEPA 24-hr PM_2.5 and PM₁₀ National Ambient Air Quality Standards (NAAQS) of 65 g m^-3 and 150 g m^-3, respectively, were exceeded on several occasions during the 30-day field campaign. Average PMconcentrations are highest when D-grade domestic coal was used, and lowest between day 11 and day 20 of the experiment when a majority of the low-smoke fuels were phased in. Source impacts from residential coal combustion are also found to be influenced by changes in meteorology, especially wind velocity.PM_2.5 and PM₁₀ mass, elements, water-soluble cations (sodium, potassium, and ammonium), anions (chloride, nitrate, and sulfate), as well as organic and elemental carbonwere measured on 15 selected days during the field campaign. PM_2.5 constituted more than 85% of PM₁₀ at three Qalabotjha residential sites, and more than 70% of PM₁₀ at the gradient site in the adjacent community of Villiers. Carbonaceous aerosol is by far the most abundant component, accounting for more than half of PM mass at the three Qalabotjha sites, and for more than a third of PM mass at the gradient site. Secondary aerosols such as sulfate, nitrate,and ammonium are also significant, constituting 8 to 12% of PM mass at the three Qalabotjha sites and 15 to 20% at the Villiers gradient site.     

北京城区降水对PM2.5和PM10清除作用分析

基于北京市PM_2.5和PM₁₀质量浓度、组分浓度以及降水数据,利用数理统计、相关性分析等方法分别从降水总量、降水时长和降水前颗粒物浓度3个角度研究降水对PM_2.5、PM₁₀的清除作用,同时以一次典型降水过程为例,具体分析降水对颗粒物的影响。结果表明：降水总量的增加有助于促进PM_2.5、PM₁₀的清除,随着降水总量增加,PM_2.5、PM₁₀的平均清除率提高,有效清除的比例增加;连续降水可增强对大气颗粒物的湿清除作用,连续降水达3d可有效降低PM_2.5、PM₁₀浓度;降水对PM_2.5、PM₁₀浓度的清除率和大气颗粒物前一日的平均浓度有较好的正相关性。降水对大气颗粒物的清除可分为清除、回升和平稳3个阶段,各个阶段大气颗粒物的变化趋势不同。降水对于大气气溶胶化学组分和酸碱性的改变具有明显作用,对于大气颗粒物各种组分的清除效果不完全相同。对于大气中OC、NO₃^-、SO₄^2-和NH₄⁺去除率较高,且这4种组分主要以颗粒态形式被冲刷进入降水中,加剧了北京市降水酸化程度。     

石家庄市大气颗粒物元素组分特征分析

为研究石家庄市大气颗粒物的污染特征及其来源,于2013年4—5月在主城6区分别采集TSP、PM10和PM2.5颗粒物样品,利用ICP-MS分析其中的22种元素浓度。结果表明,石家庄市城区Ca、Fe元素在各粒径颗粒物中含量都较高,PM2.5中的S、K含量较高,PM10和TSP中Mg、Al的浓度相对较高。颗粒物的主要来源为燃煤尘、道路尘和建筑尘,TSP、PM10和PM2.5具有较好的统计相关性和同源性。     

乌鲁木齐市冬季大气颗粒物PM_(10) 和PM_(2.5)污染水平及相关性研究

为研究乌鲁木齐市冬季采暖期间大气颗粒物污染特征,通过采样和在线监测二种手段分析了2015年1~2月大气颗粒物样品,采用重量法分析颗粒物质量浓度,并对其相关性进行分析。结果表明:依据《环境空气质量标准》(GB 3095-2012),采样期间乌鲁木齐市大气PM_(10) 和PM_(2.5)的日均质量浓度均超过了国家二级标准,颗粒物污染严重;PM_(10) 和PM_(2.5)存在显著相关性,PM_(2.5)和PM_(10) 浓度的比值均大于0.5,采暖期PM2.5对乌鲁木齐市大气颗粒物贡献显著。     

青藏高原典型城市拉萨市大气颗粒物污染源成分谱建立研究与特征分析

系统研究建立高原典型城市拉萨市开放源(土壤风沙尘、道路扬尘、施工扬尘、采矿扬尘),移动源(机动车尾气尘),固定源(工业烟粉尘、生物质燃烧尘及餐饮油烟)共3类8种大气颗粒物(PM_(2.5)、PM_(10))污染源化学成分谱。研究结果表明:开放源以地壳类元素为主,自然背景特征明显;移动源源成分谱中元素碳含量明显高于其他城市,在PM_(2.5)、PM_(10)源谱中分别占60.15%、51.86%,有机碳含量也相对较高,均超过20%;固定源中,牛粪和松柏枝两类生物质燃烧污染源的有机碳含量显著高于其他组分,工业烟粉尘中Ca远高于其他组分,在PM_(2.5)、PM_(10)源谱中分别占21.32%、21.21%。移动源、固定源源成分谱均显示出高原城市的独特特征。     

西宁市城区冬季PM2.5和PM10中有机碳、元素碳污染特征

2014年11月—2015年1月对西宁市冬季开展PM_(2.5)和PM_(10)的连续监测。利用DRI 2001A型热光碳分析仪(美国)对有机碳和元素碳进行分析,结果表明:西宁市冬季PM_(2.5)和PM_(10)中碳气溶胶所占比例分别为33.13%±6.83%、24.21%±6.27%,说明碳气溶胶主要集中在PM_(2.5)中;OC/EC值均大于2,说明西宁市大气中存在二次污染;SOC占PM_(2.5)和PM_(10)的质量浓度比例分别为46.50%和57.40%,PM_(2.5)中SOC浓度占PM_(10)中SOC浓度的61.88%,说明SOC主要存在于PM_(2.5)中,且SOC形成的二次污染和直接排放的一次污染都是西宁市碳气溶胶的主要来源;与其他城市比较发现,西宁市冬季PM_(2.5)中的碳气溶胶含量普遍高于其他城市,PM_(10)中OC质量浓度相对其他城市较高,EC质量浓度偏低;OC和EC的相关性不显著,说明来源不统一;进一步对OC和EC各组分质量浓度进行分析知,西宁市冬季碳气溶胶主要来源于机动车汽油排放、燃煤和生物质燃烧。     

杭州城区PM2.5和PM10污染特征及其影响因子分析

利用2013年12月—2014年11月杭州城区空气质量监测站PM_(2.5)、PM_(10)浓度值结合气象、道路、人口数据以及站点周边绿地信息分析PM_(2.5)、PM_(10)浓度时空特征及其影响因子。结果表明,杭州城区各监测站PM_(2.5)和PM_(10)晴天日浓度变化趋势基本一致,PM_(2.5)比PM_(10)污染严重;晴天日PM_(2.5)、PM_(10)浓度值与对应的温度(-0.463,-0.281)、风速(-0.305,-0.332)呈负相关,与湿度(0.257,0.239)呈正相关;晴天有风时,杭州市区PM_(2.5)、PM_(10)污染北部重于南部,东部重于西部,浓度极高值集中在风速小于5 m/s时段,且风速越小浓度值越高;温度为12℃左右,湿度在60%~80%时,颗粒物污染最严重;交通高峰时各监测站PM_(2.5)、PM_(10)污染程度存在明显差异。相关性分析表明,PM_(2.5)、PM_(10)污染程度与道路密度成正比,与缓冲区内绿地覆盖面积成反比。PM_(2.5)污染程度与人口密度成正比,PM_(10)污染与人口密度成反比。     

宁波市PM10、PM2.5中水溶性无机阴离子浓度水平及分布特征

研究了宁波市PM10、PM2.5中无机阴离子浓度水平及分布特征。结果表明,PM10中Cl-为1.00μg/m3,具有较明显的海洋特征,SO24-、NO3-离子浓度为9.90、3.70μg/m3;Cl-主要存在于粒径为2.5-10μm的颗粒物中,而NO3-、SO42-主要存在于PM2.5中,成为PM2.5的重要组成部分。PM10中水溶性无机阴离子季节变化明显,呈冬天高,夏天低的趋势。     

邢台市颗粒污染物变化特征和后向轨迹分析

为深入了解邢台市PM_(10)、PM_(2.5)浓度变化情况和气流后向轨迹,对邢台市2013—2016年环境大气颗粒污染物监测数据进行了分析,同时利用HYSPLIT模型计算出逐日72 h后向气流轨迹。结果表明:邢台市的PM_(10)和PM_(2.5)质量浓度在2013—2016年间呈逐年下降趋势,PM_(10)和PM_(2.5)质量浓度高值出现在冬季(296μg/m~3和192μg/m~3),最低值出现在夏季(140μg/m~3和80μg/m~3),PM_(10)和PM_(2.5)质量浓度在日变化上均呈"双峰双谷"型分布;后向轨迹的季节聚类分析表明,春季大气颗粒物污染以粒径2.5～10μm的颗粒污染物为主,夏季、秋季和冬季的大气颗粒物污染以PM_(2.5)为主;逐日聚类分析表明,在路径为西北偏西向的、途经多个沙源地的气流影响下,邢台市的PM_(10)和PM_(2.5)质量浓度处于一个相对高值;来源于偏南向的气流由于化合反应,污染物积聚导致PM_(10)、PM_(2.5)质量浓度也处于相对高值;在来源于西北向和偏北向的、水汽含量相对较低的气流影响下,邢台市的PM_(10)、PM_(2.5)质量浓度出现一个明显的下降。     

Interpretation of roadside PM10 monitoring data from Sunderland,United Kingdom

Roadside PM₁₀ has been monitored by Partisol® at three sitesin Sunderland between August 1997 and February 1998. The sites chosen were an inner city kerbside site; a roadside site adjacentto a dual carriageway on the outskirts of Sunderland with an openaspect; and a rural site.The results indicate that there is a seasonal variation in the relationship between the sites in terms of monitored PM₁₀.In the winter there is a poor correlation between the sites whereas in the summer significant correlations are obtained. Of the sites monitored PM₁₀ is consistently highest at the inner city roadside site. During the summer, exceedances of theU.K. 50 g m^-3 standard (DETR, 2000) are associated with conditions suitable for the build-up of photochemical pollutionhowever during the winter period exceedances are recorded duringa variety of weather conditions.At the dual carriageway site PM_2.5 has also been recorded and contributions to measured PM₁₀ are 77% in summer and68% in winter. The results illustrate a number of inconsistencies between this study utilising the Partisol® andothers reporting results where PM₁₀ has been monitored by TEOM®.     

上海市浦东新区大气细颗粒物中重金属污染特征及来源解析

于2017年对浦东城区和郊区大气PM2.5中的重金属特征和来源进行了分析。结果表明,K、Fe、Na、Ca、Mg、Al等矿物元素为浦东新区PM2.5中含量最高的金属元素,其中K的年均值为297.3 ng/m^3。浦东城区的不同元素在季节变化上呈现较为不同的变化规律,郊区的金属元素值大部分呈现春季先逐月下降,在夏、秋季有起伏波动,在10月之后逐渐上升;沙尘+道路源+建筑扬尘、煤燃烧、工业排放、金属冶炼、船舶排放、海盐+垃圾焚烧+生物质燃烧为浦东城区PM2.5中重金属元素的6大类主要来源。其中沙尘+道路源+建筑扬尘对Ca的贡献率为82.7%,煤燃烧对As的贡献率为86.6%,工业排放对SO4^2-的贡献率达到65.9%,金属冶炼对Cr的贡献率为75.7%,船舶排放对V的贡献率为97.5%、海盐+垃圾焚烧+生物质燃烧对Cl^-的贡献率为93.0%。煤燃烧和金属冶炼主要来自于西部方向。船舶排放分布在长江口及其延伸带。浦东新区PM2.5中重金属元素的质量浓度与本地源排放强度、外界传输和大气扩散条件均有密切关系。     

冬季大气中PM_(10)和PM_(2.5)污染特征及形貌分析

2008年冬季采集大气中PM10和PM2.5样品,利用SPSS软件进行分析。结果表明,PM10质量浓度在92.87～384.7μg/m3之间,平均值为201.09μg/m3,超标率71.43%。PM2.5浓度跨度为57.27～230.21μg/m3,平均值为133.82μg/m3,超标率89.47%。PM10和PM2.5空间分布略有差异。PM2.5/PM10在29.10%～94.76%之间,均值为66.55%。PM2.5与PM10质量浓度之间有显著相关性,相关方程:PM2.5=0.7993×PM10-55.984(R2=0.9524,置信度为95%)。通过颗粒物形貌分析,初步判定冬季大气主要污染源为燃煤和机动车尾气排放。     

天津市PM10和PM2.5中水溶性离子化学特征及来源分析

2011年5月—2012年1月在天津市南开区设立采样点,采集大气中PM10和PM2.5样品。采用离子色谱法测定颗粒物中水溶性无机阴离子、阳离子成分,分析其主要组成、季节变化及污染来源。结果表明,天津市PM10中离子平均浓度为71.2μg/m3,占PM10质量浓度的33.7%。PM2.5中离子平均浓度为54.8μg/m3,占PM2.5质量浓度的39.6%。NH+4、SO2-4、NO-3等二次离子含量较大,且夏季含量均为最高。颗粒物总体呈酸性,PM10中∑阳离子/∑阴离子平均值为0.92,PM2.5中该比值为0.75。来源分析发现,PM10可能主要来源于海盐、工业源、二次反应及土壤和建筑尘等,PM2.5则主要来源于海盐污染源、二次反应及生物质燃烧。     

南充市大气PM10与PM2.5排放清单及特征

以四川省南充市为研究区域,通过实地调研、现场测试及结合统计年鉴等获得数据,采用排放因子法计算南充市2014年大气PM_(10)、PM_(2.5)排放量并建立排放清单。结果表明,南充市2014年扬尘源、移动源、生物质燃烧源、化石燃料固定燃烧源、工艺过程源排放总量PM_(10)分别为85 187、1 777、9 175、2 417、3 519 t,PM_(2.5)分别为16 093、1 619、7 322、914、1 585 t,PM_(10)贡献率分别为83.5%、1.7%、9.0%、2.4%、3.4%,PM_(2.5)贡献率分别为58.4%、5.9%、26.6%、3.3%、5.8%。城市区域扬尘源、生物质燃烧源、移动源、化石燃料固定燃烧源、工艺过程源对PM_(10)贡献分别为60.0%、12.5%、6.3%、8.6%、12.5%,对PM_(2.5)贡献分别为41.8%、21.6%、14.4%、8.1%、14.1%。南充市2014年大气PM_(10)、PM_(2.5)排放源总量和贡献率以及区域空间分布特征均存在差异。     

基于GIS的烟台市PM10时空分布与气象因素分析

以2006-2010年的烟台城区PM₁₀监测数据及同期烟台市气象数据为依据,采用ArcGIS分析其时间、空间分布,研究几种气象因素对PM₁₀分布的影响。发现PM₁₀浓度呈现出春、冬季较高,夏、秋季较低的变化趋势,但各区域PM₁₀的变化有一定的不同。在空间上,PM₁₀表现出了一定的污染集中性,且其污染的中心随季度不同会出现移动。烟台城区内PM₁₀浓度分布与风速、湿度具有一定的相关关系,而与气温的关系为非线性。     

齐齐哈尔市PM2.5与PM10污染趋势及相关性分析

对2014—2016年齐齐哈尔市PM_(2.5)与PM_(10)质量浓度的时间变化特征进行简要分析,并探究PM_(2.5)/PM_(10)以及PM_(2.5)与PM_(10)的相关性。结果表明:2014—2016年齐齐哈尔的PM_(2.5)与PM_(10)的年均质量浓度分别为36.7、62.9μg/m~3,且呈逐渐下降趋势;冬季的PM_(2.5)与PM_(10)浓度最高,秋季次之,春季与夏季相对较低;2014—2016年PM_(2.5)与PM_(10)质量浓度月变化趋势基本相同,整体呈现2—6月逐渐下降,9—11月逐渐上升的规律;PM_(2.5)与PM_(10)质量浓度的日变化均呈双峰现象;对PM_(2.5)与PM_(10)进行线性拟合,相关系数为0.896 3。同时,残差分析也说明两者拟合情况良好,四季相关系数为r_(秋季)(0.982 2)r_(冬季)(0.964 4)r_(夏季)(0.943 9)r_(春季)(0.829 6);2014—2016年PM_(2.5)/PM_(10)平均值为55.27%,大气颗粒物PM_(2.5)的贡献率高达一半以上。     

苏州大气颗粒物PM2.5和PM10质量浓度异常“倒挂”现象的成因及影响分析

为深入研究PM_2.5和PM₁₀质量浓度异常“倒挂”现象的成因及影响,在苏州市相城区国控点开展比对监测分析,回顾性分析了2016—2020年苏州全部国控点颗粒物浓度数据。苏州市相城区国控点PM_2.5浓度的比对分析结果表明：该国控点频繁出现PM_2.5浓度高于其他国控点PM_2.5浓度和高于该站点PM₁₀浓度(“倒挂”率高达34%)的“双高”现象,PM_2.5平均浓度比其他9个国控点高12.5%～37.2%,比位于同一站点的备用监测仪器(“倒挂”率为0)高38.1%。2016—2020年,苏州全部国控点“倒挂”时间的总体趋势都是逐年递增,且集中发生在相对湿度较高的20:00至次日07:00。这5年间各国控点PM_2.5浓度异常偏高导致的异常“倒挂”现象对全市年均浓度产生的正误差分别为1.6%、2.8%、6.0%、6.2%和4.1%,基本呈现出逐年递增的趋势。上述结果表明：苏州PM_2.5浓度偏高是由动态加...     

中国北方地区采暖期颗粒物污染现状

分析了2013—2016年冬季采暖期与非采暖期中国北方地区颗粒物污染现状及时空变化特征。结果表明:中国北方地区空气污染比较严重,采暖期尤为突出。2016年,中国北方地区重度及以上污染天数比例超过10%,采暖期优良天数比例较非采暖期下降22.8%,重度及以上污染天数比例升高10.1个百分点。颗粒物浓度呈现明显的冬季高、夏季低的特点,最高值一般出现在12月至次年1月,最低值一般出现在7—9月。2013—2016年,北方地区空气质量呈较为明显的改善趋势,PM_(10)和PM_(2.5)浓度总体呈下降趋势,但2014年以来采暖期同期比较显示,PM2.5浓度呈缓慢升高趋势,采暖期空气污染形势十分严峻。颗粒物浓度呈现明显的空间分布规律,采暖期石家庄、保定、衡水、邢台、邯郸、安阳等城市为京津冀区域污染最严重的城市。