Detrimental effects of olive mill wastewater on the composting process of agricultural wastes

In order to study the suitability of composting olive mill wastewater (OMW-L) by repeated applications, OMW-L was added to one mixture of lawn trimmings and olive husks as bulking agents. The composting process of this mixture was compared with another pile having 35% of olive mill wastewater sludge (OMW-S) obtained from evaporation ponds and a third, as a control, without olive mill wastewater. The repeated applications of OMW-L resulted in a sharp decrease in respiration measurements after the first 20 days of composting and showed a re-increase after 40 days following the substituting of OMW-L by water. The OMW-L addition increased the rate of water-soluble phenols in the compost and caused the appearance of a phenol fraction of high molecular-mass (510 kDa) at the end of composting. OMW-L addition also caused a clear decrease in both thermophilic bacteria and thermophilic eumycete counts. A longer persistence of phytotoxicity was observed in comparison with the other piles. However, the OMW-S produced a compost with a high degree of maturity.     

Framework for estimating potential wastes and secondary resources accumulated within an economy – A case study of construction minerals in Japan

Material stocks in economic society are considered to represent a reserve for wastes and secondary resources. From the viewpoints of proper disposal and reutilization of stocked materials, accurate estimation of the amount of materials that will emerge as wastes or secondary resources in the future is important. We defined materials that have a high probability of emerging as wastes or secondary resources as “potential wastes and secondary resources” and estimated that amount for construction minerals in Japan as a case study. The following conclusions were drawn. (1) We classified materials that are input into economic society into four categories: potential wastes and secondary resources, potential dissipated materials, dissipatively used materials, and permanent structures. By clarifying the latter three non-potential wastes and secondary resources, we performed a more accurate assessment of the wastes and secondary resources that will emerge in the future. (2) The share of potential wastes and secondary resources was estimated to be about 30% of all construction minerals that have been input into and accumulated in Japanese economic society. (3) Information related to potential dissipated materials and dissipatively used materials will provide fundamental knowledge to support analyses of the environmental impacts and resource losses which these materials might generate.     

Contribution of the lignocellulosic fraction of two-phase olive-mill wastes to the degradation and humification of the organic matter during composting

One of the main disadvantages in the composting of two-phase olive mill wastes (TPOMW) is the long time required for its transformation (up to 40 weeks). The aim of this work was to evaluate the relationship between the degradation of the lignocellulosic fraction of TPOMW and the organic matter (OM) mineralisation rate in four composting piles prepared with different bulking agents and N-sources used to enhance OM degradation. The kinetics of degradation of the lignocellulosic fraction was compared to conventional maturation and stability indices to evaluate its impact on the duration of the composting process. The composition of bulking agents mainly affected the water-soluble fraction which influenced the OM degradation rate (linear or exponential OM degradation pattern) at early stages of the composting process but it neither modified the duration of the process (between 34 and 36 weeks) nor the total OM degradation underwent by the piles. The high initial mineral N availability was a key factor to significantly enhanced microbial activity. The mixture with urea as N-source registered the most efficient degradation of hemicellulose, cellulose and lignin, reducing the thermophilic phase and the total duration of TPOMW composting.     

Evaluation of investments in recycling centres for construction and demolition wastes in Brazilian municipalities

There are very few construction and demolition (C&D) waste recycling centres in Brazil. To encourage the building and operation of new units, data were collected and analysed relating to C&D waste management and recycling in Brazil. Based on the results of this analysis, a conceptual model is presented for conducting viability studies of future C&D waste recycling centres. Applying this model to verify the viability of private recycling centres, the results show that under current market conditions in Brazil, C&D waste recycling centres are not financially feasible based solely on revenue from the sale of processed products. Nevertheless, under the same market conditions, the recycling centres could be economically viable for public authorities depending on the particular circumstances of each municipality. The feasibility, however, depends on continuity and the production volume reached. The conceptual model, the results of its applications and the discussions about the experiences of existing centres can strongly support public authorities and private initiatives in their decision-making about investments in Brazil and in other developing countries.     

Analyses of the recycling potential of medical plastic wastes

This study analyzed the recycling potential of plastic wastes generated by health care facilities. For this study, we obtained waste streams and recycling data from five typical city hospitals and medical centers and three animal hospitals in Massachusetts. We analyzed the sources, disposal costs and plastic content of medical wastes, and also determined the components, sources, types and amounts of medical plastic wastes. We then evaluated the recycling potential of plastic wastes produced by general city hospital departments, such as cafeterias, operating rooms, laboratories, emergency rooms, ambulance service and facilities, and animal hospitals. Facilities, laboratories, operating rooms, and cafeterias were identified as major sources of plastic wastes generated by hospitals. It was determined that the recycling potential of plastics generated in hospital cafeterias was much greater than that in other departments. This was mainly due to a very slight chance of contamination or infection and simplification of purchasing plastic components. Finally, we discuss methods to increase the recycling of medical plastic wastes. This study suggests that a classification at waste generating sources, depending upon infection chance and/or plastic component, could be a method for the improved recycling of plastic wastes in hospitals.     

A comparison of mesophilic composting and unamended land treatment for the bioremediation of aged tar residues in soil

A field study was conducted to compare the effectiveness of land treatment and mesophilic composting in removing aged polycyclic aromatic hydrocarbons (PAH) from soil. The soil composting treatment, which had 20 percent (w/w) fresh organic matter incorporated into the soil, reached mesophilic temperatures of 45 to 50°C at week 3–4 and was effective in reducing PAH from 2240 mg/kg to 120 mg/kg after 224 days of treatment. Conventional land treatment with and without added cow manure (5 percent w/w) was less effective in removing the PAH from the soil than was the mesophilic soil composting treatment. In a parallel laboratory trial, PAH concentrations were reduced below 500 mg/kg (the target cleanup concentration for the site) when the contaminated soil was amended with 20 to 30 percent (w/w) fresh organic matter after 186 days of treatment. PAH degradation was lower in the laboratory trial compared with the field trial and no self-heating of soil was demonstrated in the laboratory. Based on the relatively high total heterotrophic and naphthalene-degrading microbial populations in the nonsterile treatments, it was apparent that the absence of microorganisms was unlikely to have limited the biodegradation of PAH in the current study. Fresh organic matter amendments of green tree waste and cow manure, regular mixing of the compost, and maintenance of moisture by regular watering were critical factors in achieving the target PAH concentrations.     

Evaluation of the homogeneity of stabilised/solidified wastes by a video imaging technique

A video imaging technique is described for the homogeneity assessment of wastes that have been treated by stabilisation/solidification (S/S). The method incorporates a fluorescent tracer into the S/S reagent. A test “waste” consisting of an artificial soil was stabilised/solidified with varying degrees of mixing using Portland cement as the S/S reagent. The tracer distribution was monitored with a video camera, and the cement distribution was determined by chemical analysis for calcium. Measurement of the homogeneity of the products by the video imaging technique gave results comparable to those obtained by the chemical analysis. The results warrant use of the video imaging technique in field applications since it is easier, cheaper and faster than traditional chemical methods.     

Mathematical model for carbon dioxide evolution from the thermophilic composting of synthetic food wastes made of dog food

The impacts of the aeration and the agitation on the composting process of synthetic food wastes made of dog food were studied in a laboratory-scale reactor. Two major peaks of CO(2) evolution rate were observed. Each peak represented an independent stage of composting associated with the activities of thermophilic bacteria. CO(2) evolutions known to correlate well with microbial activities and reactor temperatures were fitted successfully to a modified Gompertz equation, which incorporated three biokinetic parameters, namely, CO(2) evolution potential, specific CO(2) evolution rate, and lag phase time. No parameters that describe the impact of operating variables are involved. The model is only valid for the specified experimental conditions and may look different with others. The effects of operating parameters such as aeration and agitation were studied statistically with multivariate regression technique. Contour plots were constructed using regression equations for the examination of the dependence of CO(2) evolution potentials on aeration and agitation. In the first stage, a maximum CO(2) evolution potential was found when the aeration rate and the agitation parameter were set at 1.75 l/kg solids-min and 0.35, respectively. In the second stage, a maximum existed when the aeration rate and the agitation parameter were set at 1.8 l/kg solids-min and 0.5, respectively. The methods presented here can also be applied for the optimization of large-scale composting facilities that are operated differently and take longer time.     

A planning-level model for estimating quantities of wastes generated by the demolition of structures during remediation

A model is presented to estimate quantities of wastes generated by the demolition of various types of industrial structures. It is intended to be used for preliminary planning purposes in the absence of any detailed structure-specific information. Detailed material quantity estimates compiled for structures at the U.S. Department of Energy's Fernald site in Ohio were used to develop the statistical relationships in the model. The model provides estimates of the total quantity of wastes, the quantities of waste concrete, and the quantities of wastes that originate from at-, below-, and above-grade portions of a structure.     

Investigation of the effect of culture type on biological hydrogen production from sugar industry wastes

The bio-hydrogen generation potential of sugar industry wastes was investigated. In the first part of the study, acidogenic anaerobic culture was enriched from the mixed anaerobic culture (MAC) through acidification of glucose. In the second part of the study, glucose acclimated acidogenic seed was used, along with the indigenous microorganisms, MAC, 2-bromoethanesulfonate treated MAC and heat treated MAC. Two different COD levels (4.5 and 30 g/L COD) were investigated for each culture type. Reactors with initial COD concentration of 4.5 g/L had higher H₂ yields (20.3–87.7 mL H₂/g COD) than the reactors with initial COD concentration of 30 g/L (0.9–16.6 mL H₂/g COD). The 2-bromoethanesulfonate and heat treatment of MAC inhibited the methanogenic activity, but did not increase the H₂ production yield. The maximum H₂ production (87.7 mL H₂/g COD) and minimum methanogenic activity were observed in the unseeded reactor with 4.5 g/L of initial COD.     

The impact of pretreatment and inoculum to substrate ratio on methane potential of organic wastes from various origins

Biochemical methane potentials (BMP) of two different substrates from macroalgae (MA) and market place wastes (MPW) were investigated using anaerobic granulated sludge from food industry with different ratios of substrate to inoculum (S/X). The substrates were used as MA only, MPW only, MA–MPW mixture, pretreated MA, and pretreated MA–MPW mixture. Research involved investigation of the effects of parameters such as temperature (35, 45, and 55 °C), substrate to inoculum ratio (S/X = 0.5, 2.0, 4.0, and 6.0 as g VS_substrate/g VS_inoculum), and the type of pretreatment (by microwave, thermal, and ultrasonic) on BMP. BMP assays were performed for all substrates. The highest cumulative biogas production (and BMP) were obtained for MA only at an S/X ratio of 4.0 g VS/g VS as 357 L_biogas/kg VS (197 L CH₄/kg VS) and 33 L_biogas/kg VS (17 L CH₄/kg VS), respectively, at 35 and 55 °C. For pretreated substrates, the highest cumulative biogas production and BMP were observed as 287 L_biogas/kg VS and 146 L CH₄/kg VS using pretreated macroalgae at 35 °C. Results suggested that MA only and MA–MPW mixtures are suitable substrates for biogas production. It is also concluded that any type of pretreatment has adverse effects on biogas and methane productions.     

Waste to energy: power generation potential of putrescible wastes by anaerobic digestion process at Hyderabad,Pakistan

Journal of Material Cycles and Waste Management - Power generation from municipal solid waste plays significant role to mitigate the environmental pollution. The power generation potential of...     

Leaching tests to evaluate pollution potential of combustion residues from an iron recycling industry

Three leaching tests were applied to an industrial fly ash (cupola dust) for the evaluation of its groundwater pollution potential. The tests comprised two batch shaking tests (the SLT-test and a titration test) and a column leaching test (laboratory scale). All three tests gave valuable and consistent results with respect to the leaching of lead, zinc, cadmium and organic matter. The pH of the leaching environment was the most important factor in governing the leaching process. The results of the leaching seemed to be in accordance with observations of the groundwater quality below an actual industrial fly ash disposal site. The combination of the SLT-test and the titration test appears to be a cost-effective means of evaluating the groundwater pollution potential from industrial fly ashes.     

Developing strategies for managing construction and demolition wastes in Malaysia based on the concept of circular economy

Construction and demolition (C&D) waste is a pressing issue not only in Malaysia, but it is also a worldwide concern including the developed countries as well. C&D waste should be managed throughout the construction cycle. The concept of circular economy (CE) is an emerging notion that has the potential to be utilized as waste minimization approach. This paper aims to assess the potentials of incorporating the CE concept as an approach to minimizing C&D wastes, by developing a CE-based theoretical framework for C&D waste management in Malaysia. In line with this objective, a systematic review has been conducted to determine how CE can be operationalised as a strategy to minimize wastes, while considering it as a key factor for mitigating the environmental impacts. Based on the literature review, a CE-based theoretical framework has been proposed using Malaysia as a case study. The framework has been developed following a three-layer approach namely micro-, meso-, and macro-levels. Waste minimization strategies have been identified for each level taking into account the main stages in the construction industry, i.e., planning, designing, procurement, construction, and demolition. The different stakeholders involved at each stage and their interactions in the stages have also been identified.     

Experimental investigation of the quality characteristics of agricultural plastic wastes regarding their recycling and energy recovery potential

A holistic environmentally sound waste management scheme that transforms agricultural plastic waste (APW) streams into labelled guaranteed quality commodities freely traded in open market has been developed by the European research project LabelAgriWaste. The APW quality is defined by the APW material requirements, translated to technical specifications, for recycling or energy recovery. The present work investigates the characteristics of the APW quality and the key factors affecting it from the introduction of the virgin product to the market to the APW stream reaching the disposer. Samples of APW from different countries were traced from their application to the field through their storage phase and transportation to the final destination. The test results showed that the majority of APW retained their mechanical properties after their use preserving a "very good quality" for recycling in terms of degradation. The degree of soil contamination concerning the APW recycling and energy recovery potential fluctuates depending on the agricultural plastic category and application. The chlorine and heavy metal content of the tested APW materials was much lower than the maximum acceptable limits for their potential use in cement industries.     

The impact of cognitive aversion toward mercury on public attitude toward the construction of mercury wastes landfill site

Journal of Material Cycles and Waste Management - Minamata convention on mercury requests mercury wastes landfilling in environmentally safe manners. Owing to great difficulties to form public...     

Mass balance and characterization of bio-oil from sludge pyrolysis generated in the treatment of effluent from the biodiesel industry

Journal of Material Cycles and Waste Management - The present work produced bio-oil from the pyrolysis of sludge from the biodiesel processing industry in a fixed bed reactor, aiming at industrial...     

Comparison of batch leaching tests and influence of pH on the release of metals from construction and demolition wastes

Construction and demolition wastes are suitable for use in road construction. However, leaching characterization of recycled materials is required to determine their pollutant potential and the consequence of their application in different scenarios. The motivation of this paper is derived from the increasing use of different leaching test methods. In Europe, the confusion resulting from the wide variety of tests used to evaluate environmental properties of construction materials implies that an evaluation of the current practices and the attempt to consolidate the approaches are required.Two equilibrium-based leaching tests (the Dutch test and the European standard) were conducted to assess the environmental impact of four recycled aggregates. Three natural limestone aggregates were used as controls. Both tests measure the potential release of hazardous elements under extreme conditions using different leaching parameters (L/S ratio, pH value and contact time). The results proved that pH is the most relevant factor on the assessment of the differences between leaching methods due to its strong control on the pollutant release.To classify the materials according to their environmental effects, the concentration limit values of the metals imposed by Council Decision 2003/33/EC were used as a reference. The comparison allowed the classification of the recycled aggregates as inert wastes, with the exception of the MR-2 aggregate, which was classified as non-hazardous material.     

Evaluation of the biomethane potential of solid fish waste

Manufacturing processes in fish canning industries generate a considerable amount of solid waste that can be digested anaerobically. The aim of this research was to study the biochemical methane potential of different solid fish waste. For tuna, sardine and needle fish waste, around 0.47g COD-CH(4)/g COD(added) was obtained in batch experiments with 1%TS; whereas for mackerel waste, the methane production attained 0.59g COD-CH(4)/g COD(added). The increase in the waste/inoculum ratio, from 1.1-1.3 to 2.8-3.3g VS(waste)/g VS(inoculum), led to overload due to VFA and LCFA accumulation. Afterward, co-digestion assays of fish waste with gorse were undertaken but the biochemical methane potential did not improve.     

A multivariate approach to the study of the composting process by means of analytical electrofocusing

Three blends formed by: agro-industrial waste, wastewater sewage sludge, and their mixture, blended with tree pruning as bulking agent, were composted over a 3-month period. During the composting process the blends were monitored for the main physical and chemical characteristics. Electrofocusing (EF) was carried out on the extracted organic matter. The EF profiles were analyzed by principal component analysis (PCA) in order to assess the suitability of EF to evaluate the stabilisation level during the composting process. Throughout the process, the blends showed a general shifting of focused bands, from low to high pH, even though the compost origin affected the EF profiles. If the EF profile is analyzed by dividing it into pH regions, the interpretation of the results can be affected by the origin of compost. A good clustering of compost samples depending on the process time was obtained by analyzing the whole profile by PCA. Analysis of EF results with PCA represents a useful analytical technique to study the evolution and the stabilisation of composted organic matter.