TiO2/活性炭复合纳米纤维膜对亚甲基蓝的吸附研究

摘要以自制的TiO2/活性炭复合纳米纤维膜作为吸附剂,以亚甲基蓝为目标污染物,研究了亚甲基蓝初始浓度、温度、TiO2/活性炭复合纳米纤维膜投加量、pH等对TiO2/活性炭复合纳米纤维膜吸附去除亚甲基蓝的影响,并研究了TiO2/活性炭复合纳米纤维膜的Zeta电位、接触角、光催化再生性能.结果表明:(1)静态吸附时,随着亚...     

外负载Ce-TiO_2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭（AC）为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明：外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

纳米Au/TiO2复合物光催化降解亚甲基蓝

以纳米金棒为掺杂物,采用溶胶-凝胶法制备了纳米Au/TiO2复合材料,在紫外光下对亚甲基蓝溶液进行光催化降解。结果表明,在紫外光下,Au/TiO2复合物对亚甲基蓝的脱色率最高可达99.6%,是纯TiO2的1.3倍。这主要归结于掺杂纳米尺寸的Au可增加TiO2对光的吸收以及减少电子-空穴对的复合,由此提高其光催化能力。     

光纤传导可见光降解亚甲基蓝

针对浓度大、色度高的印染废水难以处理的情况,选用加入光纤的光催化体系进行研究。采用溶胶凝胶法制备了Ag+/TiO2粉体光催化剂,用固体紫外可见光谱、X射线衍射对其进行表征。选用亚甲基蓝溶液作为目标降解物,评价了Ag+/TiO2在可见光下的光催化活性。分别考察了加入石英芯侧光光纤与塑料侧光光纤反应体系下,催化剂量、光纤数量、光照强度和pH值等因素对亚甲基蓝降解实验的影响。结果表明,选用20 mg/L的亚甲基蓝,采用催化剂量为11.67 g/L,500根侧光光纤,300 W的外部光源,pH值约为11时,光催化降解效果最佳,均能达到90%以上。     

负载工艺对ACF担载二氧化钛光催化性能的影响

采用分散液中添加环氧树脂黏结剂并进行热处理的方法,制备出活性炭纤维(ACF)担载二氧化钛光催化材料。并对光催化材料的表面形貌和孔结构进行表征,评价复合光催化材料对亚甲基蓝溶液的光催化降解性能。重点探讨了负载方式、负载时间以及光催化剂的添加量等方面对光催化活性的影响。研究表明,当采用浸渍方式、负载时间控制在15 min左右、光催化剂添加量达11 g/L时,ACF/TiO2光催化复合材料中光催化剂负载量最佳,在15%左右,对亚甲基蓝(初始浓度为50 mg/L)的降解效果最好,在2 h内可以达到90%。     

亚甲基蓝表面修饰纳米TiO2降解造纸废水动力学

以亚甲基蓝(MB)作为表面修饰剂,采用简单的化学吸附法制备亚甲基蓝表面修饰的纳米TiO2光催化剂(TiO2-MB)。经表面修饰后,TiO2-MB光催化剂波长响应范围红移至可见光区575 nm处。探讨了光催化剂量、光照时间和溶液pH值对TiO2-MB光催化降解造纸废水的影响;研究了纳米TiO2-MB对造纸废水的暗吸附规律和光降解性能。结果表明:纳米TiO2-MB对造纸废水的吸附规律都较好地符合Langmuir和Freundlich吸附等温模型,属于吸热反应;光催化降解动力学符合Langmuir-Hinshelwood动力学模型。在160 W高压汞灯光照80 min,3.0 g/L纳米TiO2-MB光催化降解pH=2.0的造纸废水(COD:2 069.8 mg/L),COD去除率可达94.7%,处理效果远高于避光条件下。光催化剂经8次使用仍具有较高的催化活性。     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

H_4SiW_(12)O_(40)/TiO_2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶-凝胶法制备TiO2/beads光催化剂载体,然后浸渍法制备出H4SiW12O40/TiO2/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析.研究了H4SiW12O40/TiO2/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响.实验结果表明,在中性条件下,H4SiW12O40/TiO2/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%.     

ZnO在光催化降解亚甲基蓝染料领域中应用研究

以Zn(CH3COO)2·2H2O为起始原料,采用非水解溶胶—凝胶法合成ZnO光催化剂,并对其进行了表征。以亚甲基蓝为光催化反应的模型化合物,考察了ZnO光催化剂的紫外光催化活性,探索了清除剂(异丙醇、草酸铵、对苯醌、H2O2酶)对ZnO紫外光催化活性的影响。结果表明,此方法制备的ZnO具有良好的光催化性能,光照1h,ZnO光催化降解亚甲基蓝的脱色率达到84.1%;而同样条件下,TiO2光催化降解亚甲基蓝的脱色率为73.8%。     

CuO/TiO2-H2O2可见光催化亚甲基蓝脱色效果及影响因素研究

以水解法制备的锐钛矿型TiO2为载体,制备了CuO/TiO2型光催化剂.以亚甲基蓝为对象,在可见光照射下研究了H2O3加入量、pH值和催化剂投加量对脱色效果的影响,同时与改性前的TiO2催化剂进行了脱色效果的对比.结果表明亚甲基蓝在碱性条件下能较好脱色,H2O2用量和CuO/TiO2催化剂投加量分别为每1 000 mL反应液各加入10 mL和0.1 g时脱色最好;另外,TiO2催化剂也在碱性条件下能较好脱色,H2O2用量和催化剂投加量分别为每1 000 mL反应液各加入12.5 mL和0.1 g时脱色最好.最优条件下对比实验表明,CuO/TiO2型催化剂在可见光照射下具有很高的催化活性,亚甲基蓝2 h脱色率达到88%,远好于改性前的TiO2和Degussa P25催化剂.     

Photodegradation of gaseous acetaldehyde and methylene blue in aqueous solution with titanium dioxide-loaded activated carbon fiber polymer materials and aquatic plant ecotoxicity tests

TiO₂-supported activated carbon felts (TiO₂–ACFTs) were prepared by dip coating of felts composed of activated carbon fibers (ACFs) with either polyester fibers (PS-A20) and/or a polyethylene pulp (PE-W15) in a TiO₂ aqueous suspension followed by calcination at 250 °C for 1 h. The as-prepared TiO₂–ACFTs with 29–35 wt.% TiO₂ were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and N₂ adsorption. The TiO₂–ACFT(PS-A20) samples with 0 and 29 wt.% TiO₂ were microporous with specific surface areas (S _BET) of 996 and 738 m²/g, respectively, whereas the TiO₂–ACFT(PE-W15) samples with 0 and 35 wt.% TiO₂ were mesoporous with S _BET of 826 and 586 m²/g, respectively. Adsorption and photocatalytic activity of the as-prepared samples were evaluated by measuring adsorption in the dark and photodegradation of gaseous acetaldehyde (AcH) and methylene blue (MB) in aqueous solution under UV light. The TiO₂ loading caused a considerable decrease in the S _BET and MB adsorption capacity along with an increase in MB photodegradation and AcH mineralization. Lemna minor was chosen as a representative aquatic plant for ecotoxicity tests measuring detoxification of water obtained from the MB photodegradation reaction with the TiO₂–ACFT samples under UV light.     

The photocatalytic degradation of methylene blue by green semiconductor films that is induced by irradiation by a light-emitting diode and visible light

This study develops a low-energy rotating photocatalytic contactor (LE-RPC) that has Cu-doped TiO₂ films coated on stainless-steel rotating disks, to experimentally evaluate the efficiency of the degradation and decolorization of methylene blue (MB) under irradiation from different light sources (visible 430 nm, light-emitting diode [LED] 460 nm, and LED 525 nm). The production of hydroxyl radicals is also examined. The experimental results show that the photocatalytic activity of TiO₂ that is doped with Cu²⁺ is induced by illumination with visible light and an LED. More than 90% of methylene blue at a 10 mg/L concentration is degraded after illumination by visible light (430 nm) for 4 hr at 20 rpm. This study also demonstrates that the quantity of hydroxyl radicals produced is directly proportional to the light energy intensity. The greater the light energy intensity, the greater is the number of hydroxyl radicals produced.

Implications: The CuO-doped anatase TiO₂ powder was successfully synthesized in this study by a sol–gel method. The catalytic abilities of the stainless-steel film were enhanced in the visible light regions. This study has successfully modified the nano-photocatalytic materials to drop band gap and has also successfully fixed the nano-photocatalytic materials on a substratum to effectively treat dye wastewater in the range of visible light. The results can be useful to the development of a low-energy rotating photocatalytic contactor for decontamination purposes.     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料,空心微珠为载体,采用溶胶凝胶法制备TiO₂/beads光催化剂载体,然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂,并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性,考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明,在中性条件下,H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L,浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

花生壳活性炭对亚甲基蓝的吸附特性

以花生壳为原料,氯化锌为活化剂制备花生壳活性炭,采用高分辨电子扫描电镜(SEM)和氮吸脱附曲线对花生壳活性炭进行了表征.从热力学和动力学的角度,研究了花生壳活性炭对亚甲基蓝溶液的吸附行为.热力学研究表明,花生壳活性炭对亚甲基蓝的吸附符合Langmuir等温吸附方程,该吸附是自发吸热过程,吸附自由能为-52.4017～-95.1765 kJ/mol,吸附熵变为214 J/(mol·K),吸附焓变为57.49796 kJ/mol.动力学研究表明,花生壳活性炭对亚甲基蓝的吸附符合二级反应动力学方程反应特征.     

Effect of Nb doping on structural, optical and photocatalytic properties of flame-made TiO2 nanopowder

TiO₂:Nb nanopowders within a dopant concentration in the range of 0.1?C15?at.% were prepared by one-step flame spray synthesis. Effect of niobium doping on structural, optical and photocatalytic properties of titanium dioxide nanopowders was studied. Morphology and structure were investigated by means of Brunauer?CEmmett?CTeller isotherm, X-ray diffraction and transmission electron microscopy. Diffuse reflectance and the resulting band gap energy were determined by diffuse reflectance spectroscopy. Photocatalytic activity of the investigated nanopowders was revised for the photodecomposition of methylene blue (MB), methyl orange (MO) and 4-chlorophenol under UVA and VIS light irradiation. Commercial TiO₂-P25 nanopowder was used as a reference. The specific surface area of the powders was ranging from 42.9?m²/g for TiO₂:0.1?at.% Nb to 90.0?m²/g for TiO₂:15?at.% Nb. TiO₂:Nb particles were nanosized, spherically shaped and polycrystalline. Anatase was the predominant phase in all samples. The anatase-related transition was at 3.31?eV and rutile-related one at 3.14?eV. TiO₂:Nb nanopowders exhibited additional absorption in the visible range. In comparison to TiO₂-P25, improved photocatalytic activity of TiO₂:Nb was observed for the degradation of MB and MO under both UVA and VIS irradiation, where low doping level (Nb?<?1?at.%) was the most effective. Niobium doping affected structural, optical and photocatalytic properties of TiO₂. Low dopant level enhanced photocatalytic performance under UVA and VIS irradiation. Therefore, TiO₂:Nb (Nb?<?1?at.%) can be proposed as an efficient selective solar light photocatalyst.     

Enhanced photocatalytic activity using GO/TiO<Subscript>2</Subscript> catalyst for the removal of DCA solutions

This work aimed to optimize high-performance photocatalysts based on graphene oxide/titanium dioxide (GO/TiO₂) nanocomposites for the effective degradation of aqueous pollutants. The catalytic activity was tested against the degradation of dichloroacetic acid (DCA), a by-product of disinfection processes that is present in many industrial wastewaters and effluents. GO/TiO₂ photocatalysts were prepared using three different methods, hydrothermal, solvothermal, and mechanical, and varying the GO/TiO₂ ratio in the range of 1 to 10%. Several techniques were applied to characterize the catalysts, and better coupling of GO and TiO₂ was observed in the thermally synthesized composites. Although the results obtained for DCA degradation showed a coupled influence of the composite preparation method and its composition, promising results were obtained with the photocatalysts compared to the limited activity of conventional TiO₂. In the best case, corresponding to the composite synthesized via hydrothermal method with 5% of GO/TiO₂ weight ratio, an enhancement of 2.5 times of the photocatalytic degradation yield of DCA was obtained compared to bare TiO₂, thus opening more efficient ways to promote the application of photocatalytic remediation technologies.     

The enhancement of photodegradation efficiency using Pt–TiO2 catalyst

This study investigates the mechanism of photosensitization and the recombination of excited electron–hole pairs affected by depositing platinum (Pt) on the surface of titanium dioxide (TiO₂). A new catalyst of Pt–TiO₂ was prepared by a photoreduction process. Being model reactions, the photocatalytic oxidation of methylene blue (MB) and methyl orange (MO) in aqueous solutions using the Pt–TiO₂ catalyst was carried out under either UV or visible light irradiation. The experimental results indicate that an optimal content of 0.75%Pt–TiO₂ achieves the best photocatalytic performance of MB and MO degradation and that the Pt–TiO₂ catalyst can be sensitized by visible light. The interaction of Pt and TiO₂ was investigated by means of UV–Vis absorption spectra, photoluminescence emission spectra, and X-ray photoelectron emission spectroscopy. The Pt⁰, Pt²⁺ and Pt⁴⁺ species existing on the surface of Pt–TiO₂, and the Ti³⁺ species existing in its lattice may form a defect energy level. The Pt impurities, including Pt, Pt(OH)₂, and PtO₂, and the defect energy level absorb visible light more efficiently in comparison with the pure TiO₂ and hinder the recombination rate of excited electron–hole pairs.     

改性TiO2光催化降解三苯甲烷类污染物

以硫酸钛为原料采用水热法制备了掺Fe3+TiO2晶体粉末,采用X射线衍射仪(XRD)对样品的结构进行了表征。在可见光条件下,用溴酚蓝、甲基绿、甲基蓝、孔雀石绿、甲基紫和碱性品红等6种典型三苯甲烷类化合物为目标降解物,研究了以自制的掺Fe3+TiO2晶体粉末对它们的催化降解作用。实验结果表明,制备的掺Fe3+TiO2晶体属于锐钛矿型。6种化合物的光催化降解反应遵循拟一级动力学规律,且可用Langmuir-Hinshelwood(L-H)动力学模型描述,其表观反应速度常数(k)的大小顺序为:溴酚蓝<甲基绿<甲基蓝<孔雀石绿<甲基紫<碱性品红,大小变化次序与其半衰期t1/2成反比,并从分子结构上对它们的降解规律进行定性解释。