Photodegradation of quinestrol in waters and the transformation products by UV irradiation

Quinestrol is synthetic estrogen used in contraceptive and hormone replacement therapy and occasionally for treating breast cancer and prostate cancer. It can make its way into the environment through sewage discharge and waste disposal produced by human excretions. In this study, the photodegradation kinetics of quinestrol in various conditions was investigated by UV and solar irradiation. The affecting factors were studied including concentration of hydrogen peroxide, different water types, and the initial concentrations of quinestrol. Concurrently, the transformation products and presumed pathways of quinestrol in distilled water by UV irradiation were identified and proposed. The results showed that the degradation of quinestrol in both irradiation conditions followed the pseudo-first-order kinetics. More rapid degradation was observed by UV irradiation (k = 0.018 min⁻¹) than solar irradiation (k = 0.004 h⁻¹), and the photodegradation rate of quinestrol depended on the concentration of hydrogen peroxide, the initial concentration of quinestrol and water types. The transformation products of quinestrol in distilled water were identified by gas chromatography/mass spectrometry. When exposed to UV irradiation, quinestrol in aqueous solution was rapidly degraded, giving at least ten photodegradation products. The chemical structures of ten degradation products were identified on the basis of mass spectrum interpretation and literature data.     

Nitrate-induced photodegradation of atenolol in aqueous solution: kinetics, toxicity and degradation pathways

The extensive utilization of β-blockers worldwide led to frequent detection in natural water. In this study the photolysis behavior of atenolol (ATL) and toxicity of its photodegradation products were investigated in the presence of nitrate ions. The results showed that ATL photodegradation followed pseudo-first-order kinetics upon simulated solar irradiation. The photodegradation was found to be dependent on nitrate concentration and increasing the nitrate from 0.5 mM L⁻¹ to 10 mM L⁻¹ led to the enhancement of rate constant from 0.00101 min⁻¹ to 0.00716 min⁻¹. Hydroxyl radical was determined to play a key role in the photolysis process by using isopropanol as molecular probe. Increasing the solution pH from 4.8 to 10.4, the photodegradation rate slightly decreased from 0.00246 min⁻¹ to 0.00195 min⁻¹, probably due to pH-dependent effect of nitrate-induced OH formation. Bicarbonate decreased the photodegradation of ATL in the presence of nitrate ions mainly through pH effect, while humic substance inhibited the photodegradation via both attenuating light and competing radicals. Upon irradiation for 240 min, only 10% reduction of total organic carbon (TOC) can be achieved in spite of 72% transformation rate of ATL, implying a majority of ATL transformed into intermediate products rather than complete mineralization. The main photoproducts of ATL were identified by using solid phase extraction-liquid chromatography-mass spectrometry (SPE-LC-MS) techniques and possible nitrate-induced photodegradation pathways were proposed. The toxicity of the phototransformation products was evaluated using aquatic species Daphnia magna, and the results revealed that photodegradation was an effective mechanism for ATL toxicity reduction in natural waters.     

Photocatalytic removal of organic pollutants in aqueous solution by Bi(4)Nb(x)Ta((1-x))O(8)I

In this work, Bi₄Nb_xTa_(1−x)O₈I photocatalysts have been synthesized by solid state reaction method and characterized by powder X-ray diffraction, scanning electron microscope and UV-Vis near infrared diffuse reflectance spectroscopy. The photocatalytic activity of these photocatalysts was evaluated by the degradation of methyl orange (MO) in aqueous solutions under visible light, UV light and solar irradiation. The effects of catalyst dosage, initial pH and MO concentration on the removal efficiency were studied, and the photocatalytic reaction kinetics of MO degradation as well. The results indicated that Bi₄Nb_xTa_(1−x)O₈I exhibited high photocatalytic activity for the removal of MO in aqueous solutions. For example, the removal efficiency of MO by Bi₄Nb_0.1Ta_0.9O₈I was as high as 92% within 12 h visible light irradiation under the optimal conditions: initial MO concentration of 5-10 mg L⁻¹, catalyst dosage of 6 g L⁻¹ and natural pH (6-8), the MO molecules could be completely degradated by Bi₄Nb_0.1Ta_0.9O₈I within 40 min under UV light irradiation, and the photodegradation efficiency reaches to 60% after 7 h solar irradiation. Furthermore, the photocatalytic degradation of Bisphenol A (BPA) was also investigated under visible light irradiation. It is found that 99% BPA could be mineralized by Bi₄Nb_0.1Ta_0.9O₈I after 16 h visible light irradiation. Through HPLC/MS, BOD, TOC, UV-Vis measurements, we determined possible degradation products of MO and BPA. The results indicated that MO was degradated into products which are easier to be biodegradable and innocuous treated, and BPA could be mineralized completely. Furthermore, the possibility for the photosensitization effect in the degradation process of MO under visible light irradiation has been excluded.     

SMX degradation by ozonation and UV radiation: a kinetic study

The rate constants of sulfamethoxazole (SMX) degradation by ozonation and UV₂₅₄ radiation were investigated under various parameters including influent ozone gas concentration, initial SMX concentration, UV light intensity, ionic strength, water quality in terms of varying anions (bicarbonate, sulfate and nitrate), humic acid (HA) and pH. The results indicated that the removal of SMX by ozonation and UV₂₅₄ radiation fitted well to a pseudo first-order kinetic model and the rate constants were in the range of (0.9-9.8) × 10⁻³ and (1.7-18.9) × 10⁻³ s⁻¹, respectively. The second-order rate constants of SMX with ozone (k_O3), under varying operational parameters, were also determined and varied in the range of (0.60-3.38) ± 0.13 × 10⁵ M⁻¹ s⁻¹. In addition, SMX degradation through UV pretreatment followed by ozonation in the presence of HA was proved to be an effective method which can remove SMX with a low ozone dose. The results suggested that ozonation of SMX was more affected by concentration of influent ozone gas, alkalinity, and HA, while incident UV light intensity, pH, and HA were the dominant factors influencing UV degradation of SMX.     

Photodegradation of azithromycin in various aqueous systems under simulated and natural solar radiation: kinetics and identification of photoproducts

This article describes the photolysis of azithromycin, a macrolide antibiotic with reported occurrence in environmental waters, under simulated solar radiation. The photodegradation followed first-order reaction kinetics in five matrices examined. In HPLC water, the degradation rate was the slowest (half-life: 20 h), whereas in artificial freshwater supplemented with nitrate (5 mg L⁻¹) or humic acids (0.5 mg L⁻¹) the degradation of azithromycin was enhanced by factors of 5 and 16, respectively, which indicated the role of indirect photolysis involving the formation of highly reactive species. Following chromatographic separation on a UPLC system, the characterization of the transformation products was accomplished using high-resolution QqToF-MS analysis. The presence of seven photoproducts was observed and their formation was postulated to originate from (bis)-N-demethylation in the desosamine sugar, O-demethylation in the cladinose sugar, combinations thereof, as well as from hydrolytic cleavages of the desosamine and/or cladinose residue. Two of these photoproducts could also be detected in natural photodegradation process in river water which was spiked with azithromycin.     

Effects of wavelength and water quality on photodegradation of N-Nitrosodimethylamine (NDMA)

N-Nitrosodimethylamine (NDMA) is a potent carcinogen that yields a cancer risk of 10⁻⁶ at concentrations as low as 0.7 ng L⁻¹. Tentative guideline values are set at 3 ng L⁻¹ in California, USA; 9 ng L⁻¹ in Ontario, Canada; 40 ng L⁻¹ nationwide in Canada; and 100 ng L⁻¹ by the World Health Organization. NDMA is a great concern in treating reclaimed water as well as drinking water. UV degradation can be considered effective degradation method. A 1-log reduction of NDMA is achieved by 1000 mJ cm⁻² of a 254-nm low pressure (LP) mercury UV lamp. However, a higher degradation efficiency than that provided by LP lamps is desired in practical treatment. In this study, the effects of wavelength and water quality were investigated to achieve higher degradation efficiency. The effects of wavelength were examined by comparing three UV lamps: a 222-nm Kr Cl Excimer UV lamp, a 254-nm LP mercury UV lamp, and a 230- to 270-nm filtered medium pressure (FMP) mercury UV lamp. The 222-nm lamp and FMP lamp achieved 4 times and 2.8 times higher degradation efficiency, respectively, than the conventional 254-nm LP lamp. Effects on water quality were also simulated by using absorption spectrum data of nitrate solutions and process water from a drinking-water treatment plant. In the simulation, the 222-nm lamp was affected by UV-absorbing compounds in the water, whereas the FMP lamp showed more stable degradation efficiency. Appropriate use of these three types of lamps could enhance the efficiency of degradation of NDMA.     

Photodegradation of malachite green and malachite green carbinol under irradiation with different wavelength ranges

The dye malachite green (MG) is used worldwide as a fungicide in aquaculture. It is a toxic substance which in aqueous solutions is partly converted into its non-ionic colorless form (leucocarbinol). The equilibrium between these two forms is pH-dependent (pK = 6.9). To assess the photodegradation of MG under sunlight conditions, both species were irradiated separately in aqueous solutions with different pH values (4.0 and 12.0) using various ultraviolet and visible wavelength ranges (UV/VIS). A 700 W high-pressure mercury lamp with special filters was used. No artificial photooxidizers such as H₂O₂ or TiO₂ were added. MG leucocarbinol proved to be much more sensitive to irradiation than the dye form. Quantum yields Φ were calculated for some wavelength ranges as follows: MG carbinol: Φ_(280-312nm) is 4.3 × 10⁻³, Φ_(313-410nm) is 5.8 × 10⁻³, and MG dye: Φ_(280-312nm) is 4.8 × 10⁻⁵, Φ_(313-365nm) is 1.1 × 10⁻⁵, and Φ_(>365nm) is 0, respectively. Therefore, the solar photolysis of MG is an important sink and primarily depends on the photodegradation of the colorless leucocarbinol. During the irradiation of MG leucocarbinol with wavelengths >365 nm, an intermediate was formed which has photocatalytical properties.     

Photodegradation of the synthetic fragrance OTNE and the bactericide triclosan adsorbed on dried loamy sand--results from models and experiments

Fragrances such as OTNE (marketed as Iso-E-Super®) and bactericides such as triclosan (marketed as Igrasan) are present in waste water and thus finally sorbed to sewage sludge. With that sludge they can reach agricultural fields where they potentially can undergo photodegradation processes. In this study the photodegradation of OTNE and triclosan on dried loamy sand was measured under artificial sunlight conditions in laboratory experiments. These compounds were artificially added with concentrations of 1 μg g⁻¹ on pre-rinsed dried loamy sand. The decrease in concentration with light irradiation was measured for 32 d in comparison to soil samples without light irradiation. The estimated light source intensity was 27 W m⁻². Within the experiment, the apparent half-life was 7 and 17 d for OTNE and triclosan respectively. The decrease did not simply follow first-order kinetics. The apparent rate constant decreased in the latter stage of reaction, suggesting that part of the chemicals were inaccessible for degradation. Two models, i.e., a diffusion-limited model, and a light penetration-limited model, were used in comparison to the measured data to explain the observed degradation limitations in the latter stages of the experiments. Comparing the hereby obtained model parameters with estimated physico-chemical parameters for the soil and the two chemical compounds, the light penetration-limited model, in which the degradation in the soil surface layer is assumed to be limited due to the shading effect of light in the upper thin soil layer, showed to be the most realistic in describing the photodegradation.     

Fate of citalopram during water treatment with O3, ClO2, UV and Fenton oxidation

In the present study we investigate the fate of citalopram (CIT) at neutral pH using advanced water treatment technologies that include O₃, ClO₂ oxidation, UV irradiation and Fenton oxidation. The ozonation resulted in 80% reduction after 30 min treatment. Oxidation with ClO₂ removed >90% CIT at a dosage of 0.1 mg L⁻¹. During UV irradiation 85% reduction was achieved after 5 min, while Fenton with addition of 14 mg L⁻¹ (Fe²⁺) resulted in 90% reduction of CIT. During these treatment experiments transformation products (TPs) were formed from CIT, where five compounds were identified by using high resolution and tandem mass spectrometry. Among these desmethyl-citalopram and citalopram N-oxide have been previously identified as human metabolites, while three are novel and published here for the first time. The three TPs are a hydroxylated dimethylamino-side chain derivative, a butyrolactone derivative and a defluorinated derivative of CIT.     

Photo-dissociation of dimethylamine by KrBr excilamp

A study of dimethylamine photo-dissociation in the gas phase has been conducted using UV radiation delivered from a KrBr^* excilamp, driven by a sinusoidal electronic control gear with maximum emission at wavelength of 207 nm. The electrical input power and radiant power of the lamp were measured to determine their effects on the degradation. The influence of flow velocity and initial concentration of dimethylamine were also examined. In order to evaluate the photo-dissociation process comprehensively, several parameters were investigated, including removal efficiency, energy yield, carbon balance and CO₂ selectivity. It is shown that the removal efficiency increases with enhanced input power and decreased gas flow rate. A high removal efficiency of 68% is achieved for lamp power 102 W and flow velocity 15 m³ h⁻¹. The optimum dimethylamine initial concentration is around 3520 mg m⁻³, for which the energy yield reaches up to 442 g kW h⁻¹ when the input power is 65 W. In addition, two chain compounds (1,3-bis-dimethylamino-2-propanol; 3-penten-2-one, 4-amino) and three ring organic matters (1-azetidinecarboxaldehyde, 2,2,4,4-tetramethyl; N-m-tolyl-succinamic acid; p-acetoacetanisidide), were identified by GC–MS as secondary products, in order to demonstrate the pathways of the dimethylamine degradation.     

Photolysis of flumequine: identification of the major phototransformation products and toxicity measures

Direct photolysis of flumequine (FLU, 20 mg L⁻¹) in different types of water (demineralised water (DW) and synthetic seawater (SW)), was conducted in a Suntest CPS + solar simulator to evaluate its persistence and toxicity, and to identify the major phototransformation products (PTPs) generated during photolysis in DW. It was observed that FLU is susceptible to transformation when subjected to direct solar radiation. The composition of the water affects the FLU degradation kinetics, which is slower in SW. Photolytic transformation products generated during direct photolysis were identified by liquid chromatography-time of flight-mass spectrometry (LC-TOF-MS). Fourteen PTPs generated in DW were identified. The transformation of FLU begins with the opening of the heterocyclic ring by oxidation of the double bond. Loss of the fluorine atom and the hydroxylation of the aromatic ring also appear as the majority, especially in the early stages. Comparative acute toxicity evaluation by Vibrio fischeri and Daphnia magna bioassays was performed for the first and last irradiated solutions in both matrices studied. These bioassays demonstrated that in the SW matrix, the most persistent PTPs are highly toxic to D. magna but less so to V. fischeri.     

Effects of four commonly used UV filters on the growth,cell viability and oxidative stress responses of the Tetrahymena thermophila

UV filters are increasingly used in sunscreens and other personal care products. Although their residues have been widely identified in aquatic environment, little is known about the influences of UV filters to protozoan. The growth inhibition effects, cell viability and oxidative stress responses of four commonly used UV filters, 2-ethylhexyl 4-methoxycinnamate (EHMC), benzophenone-3 (BP-3), 4-methyl-benzylidene camphor (4-MBC) and octocrylene (OC), to protozoan Tetrahymena thermophila were investigated in this study. The 24-h EC₅₀ values with 95% confidence intervals for BP-3 and 4-MBC were 7.544 (6.561–8.675) mg L⁻¹ and 5.125 (4.874–5.388) mg L⁻¹, respectively. EHMC and OC did not inhibit the growth of T. thermophila after 24 h exposure at the tested concentrations. The results of cell viability assays with propidium iodide (PI) staining were consistent with that of the growth inhibition tests. As for BP-3 and 4-MBC, the relatively higher concentrations, i.e. of 10.0 and 15.0 mg L⁻¹, could lead to the cell membranes impairment after 4 h exposure. With the increase of the exposure time to 6 h, their adverse effects on cell viability of T. thermophila were observed at the relatively lower concentration groups (1.0 mg L⁻¹ and 5.0 mg L⁻¹). In addition, it is noticeable that at environmentally relevant concentration (1.0 μg L⁻¹), BP-3 and 4-MBC could lead to the significant increase of catalase (CAT) activities of the T. thermophila cells. Especially for the BP-3, the oxidative injuries were further confirmed by the reduction of glutathione (GSH) content. It is imperative to further investigate the additive action of UV filters and seek other sensitive endpoint, especially at environmentally relevant concentration.     

Determination of o-phthalic acid in snow and its photochemical degradation by capillary gas chromatography coupled with flame ionization and mass spectrometric detection

Phthalic acid and its photochemical degradation has been determined in snow and rainwater samples collected during winters (2003-2010) in the Southeast of Massachusetts using capillary gas chromatography (GC) with flame ionization and mass spectrometric detection. Water samples were dried using a rotary evaporator and derivatized with a 14% BF₃/methanol reagent before GC analysis. The developed method proved simple and accurate. Phthalic acid was found in snow samples collected in a concentration range of 7.22-76.5 nM. The photodegradation of phthalate was carried out under 300 nm UV light. The direct photodecomposition of the acid is slow (5% h⁻¹). However, the addition of dissolved Fe(III) species at 2.0 μM accelerated the light-induced degradation of phthalic acid by 3.5 times in the atmospheric water samples. Photodegradation rates of phthalic acid increases with decreasing pH value of water samples in the range of pH 2.8-4.5.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

In field arsenic removal from natural water by zero-valent iron assisted by solar radiation

An in situ arsenic removal method applicable to highly contaminated water is presented. The method is based in the use of steel wool, lemon juice and solar radiation. The method was evaluated using water from the Camarones River, Atacama Desert in northern Chile, in which the arsenic concentration ranges between 1000 and 1300 μg L⁻¹. Response surface method analysis was used to optimize the amount of zero-valent iron (steel wool) and the citrate concentration (lemon juice) to be used. The optimal conditions when using solar radiation to remove arsenic from natural water from the Camarones river are: 1.3 g L⁻¹ of steel wool and one drop (ca. 0.04 mL) of lemon juice. Under these conditions, removal percentages are higher than 99.5% and the final arsenic concentration is below 10 μg L⁻¹. This highly effective arsenic removal method is easy to use and inexpensive to implement.     

Sunlight-induced degradation of soil-adsorbed veterinary antimicrobials Marbofloxacin and Enrofloxacin

Marbofloxacin (MAR) and Enrofloxacin (ENR), two largely employed veterinary Fluoroquinolones (FQs), were found to be present at the micrograms per kilogram level in agricultural soils of South Lombardy (Italy) several months after manuring. Distribution coefficients (K_d) from sorption experiments indicated a strong binding to the soil. Soil samples fortified with environmentally significant FQs amounts (0.5 mg kg⁻¹) were exposed to solar light that promoted extensive degradation (80%) of both drugs in 60-150 h. Thus, photochemistry could be considered a significant depollution path in the soil, although it was two orders of magnitudes slower than in aqueous solution and a fraction of the drug (ca. 20%) remained unaffected. For MAR the photoprocess was the same as in solution, and involved cleavage of the tetrahydrooxadiazine ring. On the contrary, with ENR only some of the photoproducts determined in water (those arising from a stepwise oxidation of the piperazine side chain) were observed. Substitution of the 6-fluoro by a hydroxyl group and reduction did not occur in the soil, supporting the previous contention that such processes required polar solvation of FQs. Consistently with this rationalization, the irradiation of thin layers of solid drugs led to essentially the same products distribution as in the soil. From the environmental point of view it is important to notice that photodegradation mainly affects the side-chains, while the fluoroquinolone ring, to which the biological effect is associated, is conserved up to the later stages of the degradation.     

Studies on atmospheric degradation of diazinon in the EUPHORE simulation chamber

The gas phase atmospheric degradation of diazinon has been investigated at the large outdoor European Photoreactor (EUPHORE) in Valencia, Spain. The rate constant for reaction of diazinon with OH radicals was measured using a conventional relative rate method with di-n-buthylether as reference compound being k = (3.5 ± 1.2) × 10⁻¹¹ cm³ molecule⁻¹ s⁻¹ at 302 ± 10 K and atmospheric pressure. The available evidence indicates that tropospheric degradation of diazinon is mainly controlled by reaction with OH radicals, and that the tropospheric lifetime with respect to the OH reaction is estimated to be around 4 h whereas its lifetime with respect to the photolysis is higher than 1 d under our conditions. Significant aerosol formation was observed following the reaction of diazinon with OH radicals, and the main carbon-containing products detected in the particle phase were hydroxydiazinon, hydroxydiazoxon and 2-isopropyl-6-methyl-pyrimidinyl-4-ol.     

Photocatalytic degradation with immobilised TiO(2) of three selected neonicotinoid insecticides: imidacloprid, thiamethoxam and clothianidin

This research focused on photocatalytic degradation of imidacloprid, thiamethoxam and clothianidin employing a tailor-made photoreactor with six polychromatic fluorescent UVA (broad maximum at 355 nm) lamps and immobilised titanium dioxide (TiO₂) on glass slides. The disappearance was followed by high pressure liquid chromatography (HPLC-DAD) analyses, wherein the efficiency of mineralization was monitored by measurements of total organic carbon (TOC). Within 2 h of photocatalysis, all three neonicotinoids were degraded following first order kinetics with rate constants k = 0.035 ± 0.001 min⁻¹ for imidacloprid, k = 0.019 ± 0.001 min⁻¹ for thiamethoxam and k = 0.021 ± 0.000 min⁻¹ for clothianidin. However, the rate of mineralization was low, i.e. 19.1 ± 0.2% for imidacloprid, 14.4 ± 2.9% for thiamethoxam and 14.1 ± 0.4% for clothianidin. This indicates that several transformation products were formed instead. Some of them were observed within HPLC-DAD analyses and structures were proposed according to the liquid chromatography-electro spray ionization tandem mass spectrometry analyses (LC-ESI-MS/MS). The formation of clothianidin, as thiamethoxam transformation product, was reported for the first time.     

Aerobic degradation of tetrabromobisphenol-A by microbes in river sediment

This study investigated the aerobic degradation of tetrabromobisphenol-A (TBBPA) and changes in the microbial community in river sediment from southern Taiwan. Aerobic degradation rate constants (k₁) and half-lives (t_1/2) for TBBPA (50 μg g⁻¹) ranged from 0.053 to 0.077 d⁻¹ and 9.0 to 13.1 d, respectively. The degradation of TBBPA (50 μg g⁻¹) was enhanced by adding yeast extract (5 mg L⁻¹), sodium chloride (10 ppt), cellulose (0.96 mg L⁻¹), humic acid (0.5 g L⁻¹), brij 30 (55 μM), brij 35 (91 μM), rhamnolipid (130 mg L⁻¹), or surfactin (43 mg L⁻¹), with rhamnolipid yielding a higher TBBPA degradation than the other additives. For different toxic chemicals in the sediment, the results showed the high-to-low order of degradation rates were bisphenol-A (BPA) (50 μg g⁻¹) > nonylphenol (NP) (50 μg g⁻¹) > 4,4′-dibrominated diphenyl ether (BDE-15) (50 μg g⁻¹) > TBBPA (50 μg g⁻¹) > 2,2′,3,3′,4,4′,5,5′,6,6′-decabromodiphenyl ether (BDE-209) (50 μg g⁻¹). The addition of various treatments changed the microbial community in river sediments. The results also showed that Bacillus pumilus and Rhodococcus ruber were the dominant bacteria in the process of TBBPA degradation in the river sediments.     

Thermodynamic and kinetic study of phenol degradation by a non-catalytic wet air oxidation process

This work is dedicated to an accurate evaluation of thermodynamic and kinetics aspects of phenol degradation using wet air oxidation process. Phenol is a well known polluting molecule and therefore it is important having data of its behaviour during this process. A view cell is used for the experimental study, with an internal volume of 150 mL, able to reach pressures up to 30 MPa and temperatures up to 350 °C. Concerning the thermodynamic phase equilibria, experimental and modelling results are obtained for different binary systems (water/nitrogen, water/air) and ternary system (water/nitrogen/phenol). The best model is the Predictive Soave Redlich Kwong one. This information is necessary to predict the composition of the gas phase during the process. It is also important for an implementation in a process simulation. The second part is dedicated to kinetics evaluation of the degradation of phenol. Different compounds have been detected using GC coupled with a MS. A kinetic scheme is deduced, taking into account the evolution of phenol, hydroquinones, catechol, resorcinol and acetic acid. The kinetic parameters are calculated for this scheme. These data are important to evaluate the evolution of the concentration of the different polluting molecules during the process. A simplified kinetic scheme, which can be easily implemented in a process simulation, is also determined for the direct degradation of phenol into H₂O and CO₂. The Arrhenius law data obtained for the phenol disappearance are the following: k = 1.8 × 10⁶ ± 3.9 × 10⁵ M⁻¹ s⁻¹ (pre-exponential factor) and E_a = 77 ± 8 kJ mol⁻¹ (activation energy).