Use of waste brick as a partial replacement of cement in mortar

The aim of this study is to investigate the use of waste brick as a partial replacement for cement in the production of cement mortar. Clinker was replaced by waste brick in different proportions (0%, 5%, 10%, 15% and 20%) by weight for cement. The physico-chemical properties of cement at anhydrous state and the hydrated state, thus the mechanical strengths (flexural and compressive strengths after 7, 28 and 90 days) for the mortar were studied. The microstructure of the mortar was investigated using scanning electron microscopy (SEM), the mineralogical composition (mineral phases) of the artificial pozzolan was investigated by the X-ray diffraction (XRD) and the particle size distributions was obtained from laser granulometry (LG) of cements powders used in this study. The results obtained show that the addition of artificial pozzolan improves the grinding time and setting times of the cement, thus the mechanical characteristics of mortar. A substitution of cement by 10% of waste brick increased mechanical strengths of mortar. The results of the investigation confirmed the potential use of this waste material to produce pozzolanic cement.     

Use of Pb blast furnace slag as a partial substitute for fine aggregate in cement mortar

The technical properties of cement mortars containing natural fine aggregate that is replaced by lead blast furnace slag at 25 and 35% level were assessed at fixed water-to-cement (W/C) ratio and at fixed flow table value. The leachabilities of some toxic elements from the cement mortars were also assessed to test the environmental suitability of the slag for use in preparation of cement mortar. At fixed W/C ratio, the strength of the mortar decreased with increase of the slag content. On the other hand, at fixed consistency, strength increased with increasing slag content in the mortar composition. The concentrations of some toxic elements in the leachates collected from the mortars containing slag were slightly higher than for the control mortar, but the concentrations in the leachates remained within the regulatory limits for recycling in construction applications. For most elements, leaching from a mortar containing 35% of slag was similar to that from a mortar containing 25% of slag. Therefore, 35% of natural sand can be beneficially replaced with Pb slag to produce cement mortar without affecting the mechanical and leaching properties studied in this work.     

Oyster shell as substitute for aggregate in mortar.

Enormous amounts of oyster shell waste have been illegally disposed of at oyster farm sites along the southern coast of Korea. In this study to evaluate the possibility of recycling this waste for use as a construction material, the mechanical characteristics of pulverized oyster shell were investigated in terms of its potential utilization as a substitute for the aggregates used in mortar. The unconfined compressive strengths of various soil mortar specimens, with varying blending ratios of cement, water and oyster shell, were evaluated by performing unconfined compression tests, and the results were compared with the strengths of normal cement mortar made with sand. In addition, the effect of organic chemicals on the hardening of concrete was evaluated by preparing ethyl-benzene-mixed mortar specimens. The long-term strength improvement resulting from the addition of fly ash was also examined by performing unconfined compression tests on specimens with fly-ash content. There was no significant reduction in the compressive strength of the mortars containing small oyster shell particles instead of sand. From these test data, the possible application of oyster shells in construction materials could be verified, and the change in the strength parameters according to the presence of organic compounds was also evaluated.     

Matt waste from glass separated collection: an eco-sustainable addition for new building materials

Matt waste (MW), a by-product of purification processes of cullet derived from separated glass waste collection, has been studied as filler for self-compacting concrete and as an addition for newly blended cement. Properties of self-compacting concrete compared to reference samples are reported. They include characteristics at the fresh and hardened states, and the compressive strength and porosity of mortar samples that were formulated with increasing amounts of MW to be used as cement replacement (up to 50wt.%). The effects of matt waste are discussed with respect to the mechanical and microstructural characteristics of the resulting new materials.     

An investigation on the use of shredded waste PET bottles as aggregate in lightweight concrete

In this work, the utilization of shredded waste Poly-ethylene Terephthalate (PET) bottle granules as a lightweight aggregate in mortar was investigated. Investigation was carried out on two groups of mortar samples, one made with only PET aggregates and, second made with PET and sand aggregates together. Additionally, blast-furnace slag was also used as the replacement of cement on mass basis at the replacement ratio of 50% to reduce the amount of cement used and provide savings. The water–binder (w/b) ratio and PET–binder (PET/b) ratio used in the mixtures were 0.45 and 0.50, respectively. The size of shredded PET granules used in the preparation of mortar mixtures were between 0 and 4 mm. The results of the laboratory study and testing carried out showed that mortar containing only PET aggregate, mortar containing PET and sand aggregate, and mortars modified with slag as cement replacement can be drop into structural lightweight concrete category in terms of unit weight and strength properties. Therefore, it was concluded that there is a potential for the use of shredded waste PET granules as aggregate in the production of structural lightweight concrete. The use of shredded waste PET granules due to its low unit weight reduces the unit weight of concrete which results in a reduction in the death weight of a structural concrete member of a building. Reduction in the death weight of a building will help to reduce the seismic risk of the building since the earthquake forces linearly dependant on the dead-weight. Furthermore, it was also concluded that the use of industrial wastes such as PET granules and blast-furnace slag in concrete provides some advantages, i.e., reduction in the use of natural resources, disposal of wastes, prevention of environmental pollution, and energy saving.     

Physico-chemical treatment of marble processing wastewater and the recycling of its sludge.

In the first part of this study, the treatability of marble processing wastewater by the coagulation-flocculation process was investigated. Optimum coagulant-flocculant doses for turbidity removal in wastewater from the cutting, faience and equalization processes were determined as 500, 200 and 500 ppm of Al2(SO4)3; 300, 500 and 300 ppm of FeCl3 and 600, 400 and 200 ppm of Agrofloc 100 (AGRON Water Treatment Technologies and Chemical Marketing Industry and Trade Limited Company, Izmir, Turkey), respectively. It was found that the removal of total solids from cutting and equalization process wastewaters was highest for the 100 ppm dosage of all chemicals used. The amount of total solids removed from faience process wastewater by Agrofloc 100 was higher than that removed by the other chemicals used. The removals of suspended solids from cutting, faience and equalization process wastewaters were similar to each other for each of the chemicals. The pH values after treatment by Agrofloc 100 were higher than the values determined after treatment by other chemicals for all process wastewater. Electrical conductivity values, however, were lower for Agrofloc 100 than for the others. Settled sludge volume experiments showed that settled sludge volumes decreased with time. The results of the quiescent settling experiment showed that the settling type could be termed flocculent settling. In the second part of the study, the usage of waste sludge from marble processing as an additive material in cement was investigated. The waste sludge originated from the wastewaters of different steps of the marble processing plant. Waste sludge was replaced with cement at various percentages by weight to prepare the mixtures of mortar. The specimens poured into the moulds were held for 24 h, removed from the moulds and held again for 28 days in lime-saturated water at 23 degrees C. Compressive and flexural strengths were evaluated with respect to percentages of waste sludge replaced with cement. The maximum compressive and flexural strengths were observed for specimens containing a 6% waste sludge when compared with control and it was also found that waste sludge up to 9% could effectively be used as an additive material in cement.     

Chemical-mechanical characteristics of crushed oyster-shell

Enormous amount of oyster-shell waste has been illegally disposed at oyster farm sites along the southern coast of Korea. To seek for a possibility to recycle the waste as construction materials, chemical and mechanical characteristics of crushed oyster-shell were investigated. Chemical and microstructure analyses showed that oyster-shells are predominantly composed of calcium carbonate with rare impurities. Compressive strength tests for soil mortar specimens with varying blending ratio of cement, water, sand, and oyster-shell were compared with normal cement mortar. There was no significant reduction in the compressive strength up to 40% of dosages of oyster-shell instead of sand. The experimental results demonstrate that oyster-shells can be resources of pure calcareous materials and effective in replacement of sand, indicating promising reusable construction materials.     

Evaluating the strength development of mortar using clinker fine aggregate with a combination of fly ash and its inhibitory effects on alkali–silica reaction and delayed ettringite formation

The aggregate composed of cement clinker, an intermediate cement product, improves strength development and mass transfer resistance of concrete. Fly ash (FA) is a supplementary cementitious material that can be substituted by cement. This study investigated the strength development of highly FA-substituted mortar mixed with cement clinker fine aggregate (CL) and tested its inhibitory effect against the alkali–silica reaction (ASR). In addition to these, this study provides the testing results of evaluating the effects of using cement clinker fine aggregate on delayed ettringite formation (DEF), which can be problematic for precast concrete products. The study results revealed that at 91 days of age, in the case of 80% replacement ratio of fly ash to cement, using CL exhibited similar strength development as mortar with limestone fine aggregate and no FA substitution. Furthermore, mortars with 70% and 80% FA substitution did not exhibit clear ASR-induced expansion even at 182 days of age. Lastly, mortar using clinker fine aggregate could suppress DEF-induced expansion at 182 days of age, which was similar to the effect obtained using FA. These results can promote the utilization of CL resources for concrete and using clinker as fine aggregate in precast concrete products.

     

Optimization for solidification of low-level-radioactive resin using Taguchi analysis

Solidification of low-level-radioactive (LLW) resin was optimized using Taguchi analytical methodology. The ingredients in LLW mortar which caused the solidification of cement were evaluated through consecutive measurements of the effects of various concentrations of ingredients. Samples selected according to Taguchi's method were separated into 18 different categories and measured at the 7th, 21st, and 28th day after fabrication on developing effects. Evaluations of the various samples focused on whether the compressive and bending strength fulfilled the special criteria of the Taiwan Power Company (TPC). Similar results indicated that both furnace slag and fly ash were the dominant material resulting from the solidification of LLW mortar. The superior combination was obtained as furnace slag 24 wt.%, fly ash 24 wt.%, and cement 8 wt.% to mix 24 wt.% of resin with 20 wt.% of water, to fulfill the contemporary requirements of TPC.     

Physical and mechanical properties of mortars containing PET and PC waste aggregates

Non-biodegradable plastic aggregates made of polycarbonate (PC) and polyethylene terephthalate (PET) waste are used as partial replacement of natural aggregates in mortar. Various volume fractions of sand 3%, 10%, 20% and 50% are replaced by the same volume of plastic. This paper investigates the physical and mechanical properties of the obtained composites. The main results of this study show the feasibility of the reuse of PC and PET waste aggregates materials as partial volume substitutes for natural aggregates in cementitious materials. Despite of some drawbacks like a decrease in compressive strength, the use of PC and PET waste aggregates presents various advantages. A reduction of the specific weight of the cementitious materials and a significant improvement of their post-peak flexural behaviour are observed. The calculated flexural toughness factors increase significantly with increasing volume fraction of PET and PC-aggregates. Thus, addition of PC and PET plastic aggregates in cementitious materials seems to give good energy absorbing materials which is very interesting for several civil engineering applications like structures subjected to dynamic or impact efforts. The present study has shown quite encouraging results and opened new way for the recycling of PC waste aggregate in cement and concrete composites.     

Possibility of using waste tire rubber and fly ash with Portland cement as construction materials

The growing amount of waste rubber produced from used tires has resulted in an environmental problem. Recycling waste tires has been widely studied for the last 20 years in applications such as asphalt pavement, waterproofing systems and membrane liners. The aim of this study is to evaluate the feasibility of utilizing fly ash and rubber waste with Portland cement as a composite material for masonry applications. Class C fly ash and waste automobile tires in three different sizes were used with Portland cement. Compressive and flexural strength, dry unit weight and water absorption tests were performed on the composite specimens containing waste tire rubber. The compressive strength decreased by increasing the rubber content while increased by increasing the fly ash content for all curing periods. This trend is slightly influenced by particle size. For flexural strength, the specimens with waste tire rubber showed higher values than the control mix probably due to the effect of rubber fibers. The dry unit weight of all specimens decreased with increasing rubber content, which can be explained by the low specific gravity of rubber particles. Water absorption decreased slightly with the increase in rubber particles size. These composite materials containing 10% Portland cement, 70% and 60% fly ash and 20% and 30% tire rubber particles have sufficient strength for masonry applications.     

Use of waste ash from palm oil industry in concrete

Palm oil fuel ash (POFA), a by-product from the palm oil industry, is disposed of as waste in landfills. In this study, POFA was utilized as a pozzolan in concrete. The original size POFA (termed OP) was ground until the median particle sizes were 15.9 microm (termed MP) and 7.4 microm (termed SP). Portland cement Type I was replaced by OP, MP, and SP of 10%, 20%, 30%, and 40% by weight of binder. The properties of concrete, such as setting time, compressive strength, and expansion due to magnesium sulfate attack were investigated. The results revealed that the use of POFA in concretes caused delay in both initial and final setting times, depending on the fineness and degree of replacement of POFA. The compressive strength of concrete containing OP was much lower than that of Portland cement Type I concrete. Thus, OP is not suitable to be used as a pozzolanic material in concrete. However, the replacement of Portland cement Type I by 10% of MP and 20% of SP gave the compressive strengths of concrete at 90 days higher than that of concrete made from Portland cement Type I. After being immersed in 5% of magnesium sulfate solution for 364 days, the concrete bar mixed with 30% of SP had the same expansion level as that of the concrete bar made from Portland cement Type V. The above results suggest that ground POFA is an excellent pozzolanic material and can be used as a cement replacement in concrete. It is recommended that the optimum replacement levels of Portland cement Type I by MP and SP are 20% and 30%, respectively.     

Mechanical and durability properties of insulation mortar with rubber powder from waste tires

Fine rubber particles from scrap tires can be used as an insulation material by incorporating with Portland cement mortar. In addition to thermal properties, there are special mechanical and durability properties that are important for the insulation mortar. The addition of rubber particles has negative impact on these properties. The special properties for insulation mortar can be improved using cellulose ether, redispersible polymer powder (RPP), and wood fiber. The objective of this study is to investigate the effects of these additives and the rubber powder on the properties of rubberized insulation mortar. With increasing rubber content, both flexural strength and compressive strength were reduced, but the reduction of flexural strength was not as significant as for the compressive strength. At a fixed rubber content, as the optimal amount of RPP and smaller rubber powder were used, the compressive strength of rubberized mortar satisfied the minimum requirement of the type N mortar. The drying shrinkage of the rubber mortar was about the same as the ordinary cement mortar. The permeability of the rubber mortar was low comparing with that of the ordinary cement mortar. The bond strength of the rubber mortar is low due to the reduced effective bonding surface.     

Influence of combustion temperature on the performance of sewage sludge ash as a supplementary cementitious material

The potential for using sewage sludge ash (SSA) as a supplementary cementitious material (SCM) has been investigated. Controlled combustion of sewage sludge collected in Croatia from two wastewater treatment plants produced SSA with different characteristics. These were used to substitute for cement in mortar samples. The chemical composition and physical properties of SSA depend on wastewater composition, the sludge treatment process and the combustion temperature. These factors influence the suitability of SSA to be used as a SCM. For three different combustion temperatures (800, 900 and 1000 °C), it was concluded that properties of fresh mortar were not affected while in the hardened state, the most favorable combustion temperature is 900 °C regarding mechanical properties. Regardless of combustion temperature, for all types of SSA used in mortars as cement replacement (up to 30%), the average decrease in both compressive and flexural strength values was less than 8% for every 10% of added SSA. The results presented indicate that using up to 20% replacement of cement by SSA produces mortars that meet the specific technical requirements analyzed in this work.     

Utilization of power plant bottom ash as aggregates in fiber-reinforced cellular concrete

Recently, millions tons of bottom ash wastes from thermoelectric power plants have been disposed of in landfills and coastal areas, regardless of its recycling possibility in construction fields. Fiber-reinforced cellular concrete (FRCC) of low density and of high strength may be attainable through the addition of bottom ash due to its relatively high strength. This paper focuses on evaluating the feasibility of utilizing bottom ash of thermoelectric power plant wastes as aggregates in FRCC. The flow characteristics of cement mortar with bottom ash aggregates and the effect of aggregate type and size on concrete density and compressive strength were investigated. In addition, the effects of adding steel and polypropylene fibers for improving the strength of concrete were also investigated. The results from this study suggest that bottom ash can be applied as a construction material which may not only improve the compressive strength of FRCC significantly but also reduce problems related to bottom ash waste.     

The application and evaluation research of coffee residue ash into mortar

Coffee residue is usually regarded as a kind of agriculture waste; as its quantity increases the treatment of coffee residue will become an environmental problem. This research is innovative in that it derives the possibility of recycle application using coffee residue ash for cement replacement. In this research, coffee residue is burned in an electronic oven to three kinds of coffee residue ash at 500, 600 and 700 °C, and then appropriate apparatus is used to check the chemical and physical properties of these three types of coffee residue ash. After a general comparison, this study selected 500 and 600 °C coffee residue ashes with 2, 3, 5, 10 and 15 % cement replacements to make 5 cm³ cube mortar specimen to test different curing ages’ compressive strength. Through measurement and experiment, this research found that the compressive strength decreased by adding 500 or 600 °C coffee residue ash into the mortar. By considering waste reduction and practice application, this research derives that using the 600 °C coffee residue ash with 10 % replacement is better than others application, such using result also can get valuable efficiencies of financial and CO₂ reduction.     

Colloids in the mortar backfill of a cementitious repository for radioactive waste

Colloids are present in groundwater aquifers and water-permeable engineered barrier systems and may facilitate the migration of radionuclides. A highly permeable mortar is foreseen to be used as backfill for the engineered barrier of the Swiss repository for low- and intermediate-level waste. The backfill is considered to be a chemical environment with some potential for colloid generation and, due to its high porosity, for colloid mobility. Colloid concentration measurements were carried out using an in-situ liquid particle counting system. The in-house developed counting system with three commercially available sensors allowed the detection of single particles and colloids at low concentrations in the size range 50-5000 nm. The counting system was tested using suspensions prepared from certified size standards. The concentrations of colloids with size range 50-1000 nm were measured in cement pore water, which was collected from a column filled with a highly permeable backfill mortar. The chemical composition of the pore water corresponded to a Ca(OH)2-controlled cement system. Colloid concentrations in the backfill pore water were found to be typically lower than approximately 0.1 ppm. The specific (geometric) surface areas of the colloid populations were in the range 240 m2 g(-1) to 770 m2 g(-1). The low colloid inventories observed in this study can be explained by the high ionic strength and Ca concentrations of the cement pore water. These conditions are favourable for colloid-colloid and colloid-backfill interactions and unfavourable for colloid-enhanced nuclide transport.     

Effect of carbon dioxide injection on production of wood cement composites from waste medium density fiberboard (MDF)

The possibility of recycling waste medium density fiberboard (MDF) into wood-cement composites was evaluated. Both new fibers and recycled steam exploded MDF fibers had poor compatibility with cement if no treatment was applied, due to interference of the hydration process by the water soluble components of the fiber. However, this issue was resolved when a rapid hardening process with carbon dioxide injection was adopted. It appears that the rapid carbonation allowed the board to develop considerable strength before the adverse effects of the wood extractives could take effect. After 3-5 min of carbon dioxide injection, the composites reached 22-27% of total carbonation and developed 50-70% of their final (28-day) strength. Composites containing recycled MDF fibers had slightly lower splitting tensile strength and lower tensile toughness properties than those containing new fibers especially at a high fiber/cement ratio. Composites containing recycled MDF fibers also showed lower values of water absorption. Unlike composites cured conventionally, composites cured under CO(2) injection developed higher strength and toughness with increased fiber content. Incorporation of recycled MDF fibers into wood cement composites with CO(2) injection during the production stage presents a viable option for recycling of this difficult to manage waste material.     

Use of waste gypsum to replace natural gypsum as set retarders in portland cement

The present study is focused on clarifying the influence of waste gypsum (WG) in replacing natural gypsum (NG) in the production of ordinary Portland cement (OPC). WG taken from slip casting moulds in a ceramic factory was formed from the hydration of plaster of paris. Clinker and 3–5 wt% of WG was ground in a laboratory ball mill to produce cement waste gypsum (CMWG). The same procedure was repeated with NG to substitute WG to prepare cement natural gypsum (CMNG). The properties of NG and WG were investigated via X-ray Diffraction (XRD), X-ray fluorescence (XRF) and differential scanning calorimetry (DSC)/thermogravimetric (TG) to evaluate the properties of CMNG and CMWG. The mechanical properties of cement were tested in terms of setting time, flexural and compressive strength. The XRD result of NG revealed the presence of dihydrate while WG contained dihydrate and hemihydrate. The content of dihydrate and hemihydrates were obtained via DSC/TG, and the results showed that WG and NG contained 12.45% and 1.61% of hemihydrate, respectively. Furthermore, CMWG was found to set faster than CMNG, an average of 15.29% and 13.67% faster for the initial and final setting times, respectively. This was due to the presence of hemihydrate in WG. However, the values obtained for flexural and compressive strength were relatively the same for CMNG and CMWG. Therefore, this result provides evidence that WG can be used as an alternative material to NG in the production of OPC.     

The cause and influence of self-cementing properties of fine recycled concrete aggregates on the properties of unbound sub-base

The use of coarse recycled concrete aggregates (CRCA) in conjunction with fine recycled concrete aggregates (FRCA) as sub-base materials has been widely studied. Although research results indicate that it is feasible to employ both CRCA and FRCA as granular sub-base, the influence of the unhydrated cement in the adhered mortar of the RCA on the properties of the sub-base materials has not been thoroughly studied. Generally, it is known that the strength of the sub-base materials prepared with RCA increases over time. However, this mechanism, known as the self-cementing properties, is not well understood and is believed to be governed by the properties of the fine portion of the RCA (<5mm). This paper presents an investigation on the cause of the self-cementing properties by measuring X-ray diffraction patterns, pH values, compressive strength and permeability of various size fractions of the FRCA obtained from a commercially operated construction and demolition waste recycling plant. Their influence on the overall sub-base materials was determined. The results indicate that the size fractions of <0.15 and 0.3-0.6mm (active fractions) were most likely to be the principal cause of the self-cementing properties of the FRCA. However, the effects on the properties of the overall RCA sub-base materials were minimal if the total quantity of the active fractions was limited to a threshold by weight of the total fine aggregate.