Central power generation versus distributed generation – An air quality assessment in the South Coast Air Basin of California

This study assesses the air quality impacts of central power generation and compares them with the impacts of distributed generation (DG). The central power plant emissions factors used are from a newly installed combined cycle gas turbine system. Because location of power plants is a key parameter affecting air quality impacts, this study considers three potential locations for the installation of central power plants. Air quality impacts are evaluated for the South Coast Air Basin of California, in the year 2010, using a three-dimensional air quality model. Results are compared to air quality impacts from two potential DG scenarios to meet the same power demand as that of the central power plant case.Even though emissions from central generation are lower than emissions from the DG technology mix considered herein, central generation concentrates emissions in a small area, whereas DG spreads emissions throughout a larger cross-section of the air basin. As a result, air quality impacts from central generation are more significant than those from DG. The study also shows that assessment of air quality impacts from distributed and central generation should not only consider emissions levels, but also the spatial and temporal distribution of emissions and the air quality that results from atmospheric chemistry and transport – highly non-linear processes.Finally, analysis of population exposure to ozone and PM_2.5 shows that central generation located in coastal areas upwind from populated areas would cause the highest population exposure and even though emissions from central generation are considerably lower than DG emissions spread throughout the basin, results show that central generation causes a higher pollutant exposure than DG.     

Near-source air quality impacts of large olefin flares

Large petrochemical flares, common in the Houston Ship Channel (the Ship Channel) and other industrialized areas in the Gulf of Mexico region, emit hundreds to thousands of pounds per hour of highly reactive volatile organic compounds (HRVOCs). We employed fine horizontal resolution (200 m?×?200 m) in a three-dimensional (3D) Eulerian chemical transport model to simulate two historical Ship Channel flares. The model reasonably reproduced the observed ozone rise at the nearest monitoring stations downwind of the flares. The larger of the two flares had an olefin emission rate exceeding 1400 lb/hr. In this case, the model simulated a rate of increase in peak ozone greater than 40 ppb/hr over a 12 km?×?12 km horizontal domain without any unusual meteorological conditions. In this larger flare, formaldehyde emissions typically neglected in official inventories enhanced peak ozone by as much as 16 ppb and contributed over 10 ppb to ambient formaldehyde up to ～8 km downwind of the flare. The intense horizontal gradients in large flare plumes cannot be simulated by coarse models typically used to demonstrate ozone attainment. Moreover, even the relatively dense monitoring network in the Ship Channel may not be able to detect many transient high ozone events (THOEs) caused by industrial flare emissions in the absence of stagnant air recirculation or stalled sea breeze fronts, even though such conditions are unnecessary for the occurrence of THOEs.

Implications: Flare minimization may be an important strategy to attain the U.S. federal ozone standard in industrialized areas, and to avoid inordinate exposure to formaldehyde in neighborhoods surrounding petrochemical facilities. Moreover, air quality monitoring networks, emission inventories, and chemical transport models with higher spatial and temporal resolution and more refined speciation of HRVOCs are needed to better account for the near-source air quality impacts of large olefin flares.     

Near-source air quality impacts of large olefin flares

Large petrochemicalflares, common in the Houston Ship Channel (the Ship Channel) and other industrialized areas in the Gulfof Mexico region, emit hundreds to thousands of pounds per hour of highly reactive volatile organic compounds (HRVOCs). We employedfine horizontal resolution (200 mx200 m) in a three-dimensional (3D) Eulerian chemical transport model to simulate two historical Ship Channel flares. The model reasonably reproduced the observed ozone rise at the nearest monitoring stations downwind of the flares. The larger of the two flares had an olefin emission rate exceeding 1400 lb/hr. In this case, the model simulated a rate of increase in peak ozone greater than 40 ppb/hr over a 12 kmx12 km horizontal domain without any unusual meteorological conditions. In this larger flare, formaldehyde emissions typically neglected in official inventories enhanced peak ozone by as much as 16 ppb and contributed over 10 ppb to ambient formaldehyde up to approximately 8 km downwind of the flare. The intense horizontal gradients in large flare plumes cannot be simulated by coarse models typically used to demonstrate ozone attainment. Moreover even the relatively dense monitoring network in the Ship Channel may not be able to detect many transient high ozone events (THOEs) caused by industrial flare emissions in the absence of stagnant air recirculation or stalled sea breeze fronts, even though such conditions are unnecessary for the occurrence of THOEs.     

生物质能利用技术控制污染物排放的作用

化石燃料燃烧利用过程中排放的大量毒害气体和CO2对生态环境造成重大危害,由此产生的环境问题越来越引起世界各国的关注,相应的控制排放技术不断发展,其中生物质能利用由于其CO2零排放成为最有发展潜力的技术之一.采用LCA方法,选择生物质气化联合循环发电、生物质热裂解发电、生物质与煤混烧发电3种方案与燃煤发电进行了对比,分析生物质利用过程减排温室气体CO2、毒性气体(SOX、NOX)的作用.结果表明,在生产1 kW*h电能的生命周期中,3种生物质发电方案的CO2排放量远远小于燃煤发电,特别是生物质气化联合循环发电和生物质热裂解发电两种方案减排CO2达到了87%～94%.由于生物质低硫和低氮特性,该两种方案中NOX和SOX的减排量也非常显著,即使是生物质与煤按1∶9(质量比)混燃都可以达到25.2%和8.9%的减排效果.综合而言,生物质能的利用,不论是气化、热解或者共燃都是减排CO2、NOX和SOX有效措施.     

Future impacts of distributed power generation on ambient ozone and particulate matter concentrations in the San Joaquin Valley of California

Distributed power generation-electricity generation that is produced by many small stationary power generators distributed throughout an urban air basin-has the potential to supply a significant portion of electricity in future years. As a result, distributed generation may lead to increased pollutant emissions within an urban air basin, which could adversely affect air quality. However, the use of combined heating and power with distributed generation may reduce the energy consumption for space heating and air conditioning, resulting in a net decrease of pollutant and greenhouse gas emissions. This work used a systematic approach based on land-use geographical information system data to determine the spatial and temporal distribution of distributed generation emissions in the San Joaquin Valley Air Basin of California and simulated the potential air quality impacts using state-of-the-art three-dimensional computer models. The evaluation of the potential market penetration of distributed generation focuses on the year 2023. In general, the air quality impacts of distributed generation were found to be small due to the restrictive 2007 California Air Resources Board air emission standards applied to all distributed generation units and due to the use of combined heating and power. Results suggest that if distributed generation units were allowed to emit at the current Best Available Control Technology standards (which are less restrictive than the 2007 California Air Resources Board standards), air quality impacts of distributed generation could compromise compliance with the federal 8-hr average ozone standard in the region.     

Air quality impacts of power plant emissions in Beijing

The CALMET/CALPUFF modeling system was applied to estimate the air quality impacts of power plants in 2000 and 2008 in Beijing, and the intake fractions (IF) were calculated to see the public health risks posed. Results show that in 2000 the high emission contribution induced a relatively small contribution to average ambient concentration and a significant impact on the urban area (9.52 microg/m(3) of SO(2) and 5.29 microg/m(3) of NO(x)). The IF of SO(2), NO(x) and PM(10) are 7.4 x 10(-6), 7.4 x 10(-6) and 8.7 x 10(-5), respectively. Control measures such as fuel substitution, flue gas desulfurization, dust control improvement and flue gas denitration planned before 2008 will greatly mitigate the SO(2) and PM(10) pollution, especially alleviating the pressure on the urban area to reach the National Ambient Air Quality Standard (NAAQS). NO(x) pollution will be mitigated with 34% decrease in concentration but further controls are still needed.     

Air quality impacts of distributed energy resources implemented in the northeastern United States

Emissions from the potential installation of distributed energy resources (DER) in the place of current utility-scale power generators have been introduced into an emissions inventory of the northeastern United States. A methodology for predicting future market penetration of DER that considers economics and emission factors was used to estimate the most likely implementation of DER. The methodology results in spatially and temporally resolved emission profiles of criteria pollutants that are subsequently introduced into a detailed atmospheric chemistry and transport model of the region. The DER technology determined by the methodology includes 62% reciprocating engines, 34% gas turbines, and 4% fuel cells and other emerging technologies. The introduction of DER leads to retirement of 2625 MW of existing power plants for which emissions are removed from the inventory. The air quality model predicts maximum differences in air pollutant concentrations that are located downwind from the central power plants that were removed from the domain. Maximum decreases in hourly peak ozone concentrations due to DER use are 10 ppb and are located over the state of New Jersey. Maximum decreases in 24-hr average fine particulate matter (PM2.5) concentrations reach 3 microg/m3 and are located off the coast of New Jersey and New York. The main contribution to decreased PM2.5 is the reduction of sulfate levels due to significant reductions in direct emissions of sulfur oxides (SO(x)) from the DER compared with the central power plants removed. The scenario presented here represents an accelerated DER penetration case with aggressive emission reductions due to removal of highly emitting power plants. Such scenario provides an upper bound for air quality benefits of DER implementation scenarios.     

Development of risk-based air quality management strategies under impacts of climate change

Climate change is forecast to adversely affect air quality through perturbations in meteorological conditions, photochemical reactions, and precursor emissions. To protect the environment and human health from air pollution, there is an increasing recognition of the necessity of developing effective air quality management strategies under the impacts of climate change. This paper presents a framework for developing risk-based air quality management strategies that can help policy makers improve their decision-making processes in response to current and future climate change about 30-50 years from now. Development of air quality management strategies under the impacts of climate change is fundamentally a risk assessment and risk management process involving four steps: (1) assessment of the impacts of climate change and associated uncertainties; (2) determination of air quality targets; (3) selections of potential air quality management options; and (4) identification of preferred air quality management strategies that minimize control costs, maximize benefits, or limit the adverse effects of climate change on air quality when considering the scarcity of resources. The main challenge relates to the level of uncertainties associated with climate change forecasts and advancements in future control measures, since they will significantly affect the risk assessment results and development of effective air quality management plans. The concept presented in this paper can help decision makers make appropriate responses to climate change, since it provides an integrated approach for climate risk assessment and management when developing air quality management strategies. Implications: Development of climate-responsive air quality management strategies is fundamentally a risk assessment and risk management process. The risk assessment process includes quantification of climate change impacts on air quality and associated uncertainties. Risk management for air quality under the impacts of climate change includes determination of air quality targets, selections of potential management options, and identification of effective air quality management strategies through decision-making models. The risk-based decision-making framework can also be applied to develop climate-responsive management strategies for the other environmental dimensions and assess costs and benefits of future environmental management policies.     

Wildfire and prescribed burning impacts on air quality in the United States

ABSTRACT

Air quality impacts from wildfires have been dramatic in recent years, with millions of people exposed to elevated and sometimes hazardous fine particulate matter (PM _2.5 ) concentrations for extended periods. Fires emit particulate matter (PM) and gaseous compounds that can negatively impact human health and reduce visibility. While the overall trend in U.S. air quality has been improving for decades, largely due to implementation of the Clean Air Act, seasonal wildfires threaten to undo this in some regions of the United States. Our understanding of the health effects of smoke is growing with regard to respiratory and cardiovascular consequences and mortality. The costs of these health outcomes can exceed the billions already spent on wildfire suppression. In this critical review, we examine each of the processes that influence wildland fires and the effects of fires, including the natural role of wildland fire, forest management, ignitions, emissions, transport, chemistry, and human health impacts. We highlight key data gaps and examine the complexity and scope and scale of fire occurrence, estimated emissions, and resulting effects on regional air quality across the United States. The goal is to clarify which areas are well understood and which need more study. We conclude with a set of recommendations for future research.     

北京市燃煤的空气质量影响及其控制研究

建立了2005年北京市燃煤污染源排放清单,利用MM5-CMAQ模型计算了各区县各行业燃煤对北京市空气质量的影响。研究表明,2005年1月北京市燃煤源对各监测站点SO_2浓度的贡献在70%以上,对PM_(10)和NO_x浓度的贡献约为20%～40%和10%～30%;7月本地燃煤源对SO_2浓度的贡献在40%～50%左右。1月采暖锅炉对空气质量影响最大,占50%～70%;7月电厂的影响最大。依据北京市奥运空气质量保障方案以及"十一五"期间能源规划,建立了2010年燃煤污染源大气排放的规划情景,并模拟了各规划措施对大气质量的改善效果。通过实施电厂脱硫脱硝除尘、炼焦工业停产、钢铁行业和水泥行业搬迁减产、供热锅炉改造、平房用煤改造等措施,与2005年相比,SO_2平均浓度下降30%左右,NO_x和PM_(10)浓度的下降幅度15%。     

The use of air quality forecasts to assess impacts of air pollution on crops: Methodology and case study

It has been reported that ambient ozone (O₃), either alone or in concurrence with acid rain precursors, accounts for up to 90% of US crop losses resulting from exposure to all major air pollutants. Crop damage due to O₃ exposure is of particular concern as ambient O₃ concentrations remain high in many major food-producing regions. Assessing O₃ damage to crops is challenging due to the difficulties in determining the reduction in crop yield that results from exposure to surface O₃, for which monitors are limited and mostly deployed in non-rural areas. This work explores the potential benefits of using operational air quality forecast (AQF) data to estimate rural O₃ exposure. Using the results from the first nationwide AQF as a case study, we demonstrate how the O₃ data provided by AQF can be combined with concurrent crop information to assess O₃ damages to soybeans in the United States. We estimate that exposure to ambient O₃ reduces the US soybean production by 10% in 2005.     

Application of a scenario-based modeling system to evaluate the air quality impacts of future growth

The structure and design of future urban development can have significant adverse effects on air pollutant emissions as well as other environmental factors. When considering the future impact of growth on mobile source emissions, we generally model the increase in vehicle kilometers traveled (VKT) as a function of population growth. However, diverse and poorly planned urban development (i.e., urban sprawl) can force higher rates of motor vehicle use and in return increase levels of pollutant emissions than alternative land-use scenarios. The objective of this study is to develop and implement an air quality assessment tool that takes into account the influence of alternative growth and development scenarios on air quality.The use of scenario-based techniques in land use planning has been around since the late 1940s and been tested in many different applications to aid in decision-making. In this study, we introduce the development of an advanced interactive scenario-based land use and atmospheric chemistry modeling system coupled with a GIS (Geographical Information System) framework. The modeling system is designed to be modular and includes land use/land cover information, transportation, meteorological, emissions, and photochemical modeling components. The methods and modularity of the developed system allow its application to both broad areas and applications.To investigate the impact of possible land use change and urbanization, we evaluated a set of alternative future patterns of land use developed for a study area in Southwest California. Four land use and two population variants (increases of 500k and 1M) were considered. Overall, a Regional Low-Density Future was seen to have the highest pollutant emissions, largest increase in VKT, and the greatest impact on air quality. On the other hand, a Three-Centers Future appeared to be the most beneficial alternative future land-use scenario in terms of air quality. For all cases, the increase in population was the main factor leading to the change on predicted pollutant levels.     

Assessment of the emissions and air quality impacts of biomass and biogas use in California

It is estimated that there is sufficient in-state “technically” recoverable biomass to support nearly 4000 MW of bioelectricity generation capacity. This study assesses the emissions of greenhouse gases and air pollutants and resulting air quality impacts of new and existing bioenergy capacity throughout the state of California, focusing on feedstocks and advanced technologies utilizing biomass resources predominant in each region. The options for bioresources include the production of bioelectricity and renewable natural gas (NG). Emissions of criteria pollutants and greenhouse gases are quantified for a set of scenarios that span the emission factors for power generation and the use of renewable natural gas for vehicle fueling. Emissions are input to the Community Multiscale Air Quality (CMAQ) model to predict regional and statewide temporal air quality impacts from the biopower scenarios. With current technology and at the emission levels of current installations, maximum bioelectricity production could increase nitrogen oxide (NO_x) emissions by 10% in 2020, which would cause increases in ozone and particulate matter concentrations in large areas of California. Technology upgrades would achieve the lowest criteria pollutant emissions. Conversion of biomass to compressed NG (CNG) for vehicles would achieve comparable emission reductions of criteria pollutants and minimize emissions of greenhouse gases (GHG). Air quality modeling of biomass scenarios suggest that applying technological changes and emission controls would minimize the air quality impacts of bioelectricity generation. And a shift from bioelectricity production to CNG production for vehicles would reduce air quality impacts further. From a co-benefits standpoint, CNG production for vehicles appears to provide the best benefits in terms of GHG emissions and air quality.

Implications:?This investigation provides a consistent analysis of air quality impacts and greenhouse gas emissions for scenarios examining increased biomass use. Further work involving economic assessment, seasonal or annual emissions and air quality modeling, and potential exposure analysis would help inform policy makers and industry with respect to further development and direction of biomass policy and bioenergy technology alternatives needed to meet energy and environmental goals in California.     

Creating markets for combined heat and power and clean distributed generation in New York State

Combined heat and power (CHP) is the simultaneous production of electrical or mechanical power and thermal energy from in a single process. Because thermal output from the generation of electricity is captured and utilized onsite, CHP systems can achieve efficiencies from 60% to as high as 90%. In contrast generation of electric power at sites remote from the loads served often results in efficiencies of 33% or less due to losses in generation and transmission and distribution of the power to ultimate end users. A well designed CHP system is the essence of energy efficiency. It may also provide significant environmental benefits. However, the full promise of CHP for improving the efficiency and productivity of businesses and the quality of the environment is unlikely to be realized given the current market structure and regulatory environment in which CHP projects are forced to compete. This paper examines the market structure and regulatory obstacles that hinder the development of more robust markets for CHP in New York State.     

Aircraft emissions and local air quality impacts from takeoff activities at a large International Airport

Real time number concentrations and size distributions of ultrafine particles (UFPs, diameter <100 nm) and time integrated black carbon, PM_2.5 mass, and chemical species were studied at the Los Angeles International Airport (LAX) and a background reference site. At LAX, data were collected at the blast fence (∼140 m from the takeoff position) and five downwind sites up to 600 m from the takeoff runway and upwind of the 405 freeway. Size distributions of UFPs collected at the blast fence site showed very high number concentrations, with the highest numbers found at a particle size of approximately 14 nm. The highest spikes in the time series profile of UFP number concentrations were correlated with individual aircraft takeoff. Measurements indicate a more than 100-fold difference in particle number concentrations between the highest spikes during takeoffs and the lowest concentrations when no takeoff is occurring. Total UFP counts exceeded 10⁷ particles cm⁻³ during some monitored takeoffs. Time averaged concentrations of PM_2.5 mass and two carbonyl compounds, formaldehyde and acrolein, were statistically elevated at the airport site relative to a background reference site. Peaks of 15 nm particles, associated with aircraft takeoffs, that occurred at the blast fence were matched with peaks observed 600 m downwind, with time lags of less than 1 min. The results of this study demonstrate that commercial aircraft at LAX emit large quantities of UFP at the lower end of currently measurable particle size ranges. The observed highly elevated UFP concentrations downwind of LAX associated with aircraft takeoff activities have significant exposure and possible health implications.     

The impacts of reactive terpene emissions from plants on air quality in Las Vegas,Nevada

A three-part study was conducted to quantify the impact of landscaped vegetation on air quality in a rapidly expanding urban area in the arid southeastern United States. The study combines in situ, plant-level measurements, a spatial emissions inventory, and a photochemical box model. Maximum plant-level basal emission rates were moderate: 18.1 μgC gdw^?1 h^?1 (Washingtonia spp., palms) for isoprene and 9.56 μgC gdw^?1 h^?1 (Fraxinus velutina, Arizona ash) for monoterpenes. Sesquiterpene emission rates were low for plant species selected in this study, with no measurement exceeding 0.1 μgC gdw^?1 h^?1. The high ambient temperatures combined with moderate plant-level emission factors resulted in landscape emission factors that were low (250–640 μgC m^?2 h^?1) compared to more mesic environments (e.g., the southeastern United States). The Regional Atmospheric Chemistry Mechanism (RACM) was modified to include a new reaction pathway for ocimene. Using measured concentrations of anthropogenic hydrocarbons and other reactive air pollutants (NO_x, ozone), the box model employing the RACM mechanism revealed that these modest emissions could have a significant impact on air quality. For a suburban location that was downwind of the urban core (high NO_x; low anthropogenic hydrocarbons), biogenic terpenes increased time-dependent ozone production rates by a factor of 50. Our study demonstrates that low-biomass density landscapes emit sufficient biogenic terpenes to have a significant impact on regional air quality.     

Simulations of the impacts of building height layout on air quality in natural-ventilated rooms around street canyons

Numerical simulations were conducted to investigate the effects of building height ratio (i.e., HR, the height ratio of the upstream building to the downstream building) on the air quality in buildings beside street canyons, and both regular and staggered canyons were considered for the simulations. The results show that the building height ratio affects not only the ventilation fluxes of the rooms in the downstream building but also the pollutant concentrations around the building. The parameter, outdoor effective source intensity of a room, is then proposed to calculate the amount of vehicular pollutants that enters into building rooms. Smaller value of this parameter indicates less pollutant enters the room. The numerical results reveal that HRs from 2/7 to 7/2 are the favorable height ratios for the regular canyons, as they obtain smaller values than the other cases. While HR values of 5/7, 7/7, and 7/5 are appropriate for staggered canyons. In addition, in terms of improving indoor air quality by natural ventilation, the staggered canyons with favorable HR are better than those of the regular canyons.     

The impacts of combustion emissions on air quality and climate – From coal to biofuels and beyond

Combustion processes have inherent characteristics that lead to the release in the environment of both gaseous and particulate pollutants that have primary and secondary impacts on air quality, human health, and climate. The emissions from the combustion of fossil fuels and biofuels and their atmospheric impacts are reviewed here with attention given to the emissions of the currently regulated pollutant gasses, primary aerosols, and secondary aerosol precursors as well as the emissions of non-regulated pollutants. Fuels ranging from coal, petroleum, liquefied petroleum gas (LPG), natural gas, as well as the biofuels; ethanol, methanol, methyl tertiary-butyl ether (MTBE), ethyl tertiary-butyl ether (ETBE), and biodiesel, are discussed in terms of the known air quality and climate impacts of the currently regulated pollutants. The potential importance of the non-regulated emissions of both gasses and aerosols in air quality issues and climate is also discussed with principal focus on aldehydes and other oxygenated organics, polycyclic aromatic hydrocarbons (PAHs), and nitrated organics. The connection between air quality and climate change is also addressed with attention given to ozone and aerosols as potentially important greenhouse species.