PM10 and PM2.5 source apportionment in the Barcelona Metropolitan area, Catalonia, Spain

Levels of total suspended particles, PM10, PM2.5 and PM1 were continuously monitored at an urban kerbside in the Metropolitan area of Barcelona from June 1999 to June 2000. The results show that hourly levels of PM2.5 and PM1 are consistent with the daily cycle of gaseous pollutants emitted by traffic, whereas TSP and PM10 do not follow the same trend, at least in the diurnal period. The PM2.5/PM10 ratio is dependent on the traffic emissions, whereas additional contribution sources for the >10 μm fraction must be taken into account in the diurnal period. Different PM10 and PM2.5 source apportionment techniques were compared. A methodology based on the chemical determination of 83% of both PM10 and PM2.5 masses allowed us to quantify the marine (4% in PM10 and <1% in PM2.5), crustal (26% in PM10 and 8% in PM2.5) and anthropogenic (54% in PM10 and 73% in PM2.5) loads. Peaks of crustal contribution to PM10 (up to 44% of the PM10 mass) were recorded under Saharan air mass intrusions. A different seasonal trend was observed for levels of sulphate and nitrate, probably as a consequence of the different thermodynamic behaviour of these PM species and the higher summer oxidation rate of SO₂.     

The stable carbon isotope composition of PM2.5 and PM10 in Mexico City Metropolitan Area air

The sources and distribution of carbon in ambient suspended particles (PM_2.5 and PM₁₀) of Mexico City Metropolitan Area (MCMA) air were traced using stable carbon isotopes (¹³C/¹²C). Tested potential sources included rural and agricultural soils, gasoline and diesel, liquefied-petroleum gas, volcanic ash, and street dust. The complete combustion of LP gas, diesel and gasoline yielded the lightest δ¹³C values (?27 to ?29‰ vs. PDB), while street dust (PM₁₀) represented the isotopically heaviest endmember (?17‰). The δ¹³C values of rural soils from four geographically separated sites were similar (?20.7 ± 1.5‰). δ¹³C values of particles and soot from diesel and gasoline vehicle emissions and agricultural soils varied between ?23 and ?26‰. Ambient PM samples collected in November of 2000, and March and December of 2001 at three representative receptor sites of industrial, commercial and residential activities had a δ¹³C value centered around ?25.1‰ in both fractions, resulting from common carbon sources. The predominant carbon sources to MCMA atmospheric particles were hydrocarbon combustion (diesel and/or gasoline) and particles of geological origin. The significantly depleted δ¹³C values from the industrial site reflect the input of diesel combustion by mobile and point source emissions. Based on stable carbon isotope mass balance, the carbon contribution of geological sources at the commercial and residential sites was approximately 73% for the PM₁₀ fraction and 54% for PM_2.5. Although not measured in this study, biomass-burning emissions from nearby forests are an important carbon source characterized by isotopically lighter values (?29‰), and can become a significant contributor (67%) of particulate carbon to MCMA air under the prevalence of southwesterly winds. Alternative sources of these ¹³C-depleted particles, such as cooking fires and municipal waste incineration, need to be assessed. Results show that stable carbon isotope measurements are useful for distinguishing between some carbon sources in suspended particles to MCMA air, and that wind direction has an impact on the distribution of carbon sources in this basin.     

Chemical characterization and factor analysis of PM2.5 in two sites of Monterrey, Mexico

The Monterrey Metropolitan Area (MMA) has shown a high concentration of PM2.5 in its atmosphere since 2003. The contribution of possible sources of primary PM2.5 and its precursors is not known. In this paper we present the results of analyzing the chemical composition of sixty 24-hr samples of PM2.5 to determine possible sources of PM2.5 in the MMA. The samples were collected at the northeast and southeast of the MMA between November 22 and December 12, 2007, using low-volume devices. Teflon and quartz filters were used to collect the samples. The concentrations of 16 airborne trace elements were determined using x-ray fluorescence (XRF). Anions and cations were determined using ion chromatography. Organic carbon (OC) and elemental carbon (EC) were determined by thermal optical analysis. The results show that Ca had the maximum mean concentration of all elements studied, followed by S. Enrichment factors above 50 were calculated for S, Cl, Cu, Zn, Br and Pb. This indicates that these elements may come from anthropogenic sources. Overall, the major average components of PM2.5 were OC (41.7%), SO4(2-) (22.9%), EC (7.4%), crustal material (11.4%), and NO3- (12.6%), which altogether accounted for 96% of the mass. Statistically, we did not find any difference in SO4(2-) concentrations between the two sites. The fraction of secondary organic carbon was between 24% and 34%. The results of the factor analysis performed over 10 metals and OC and EC show that there are three main sources of PM2.5: crustal material and vehicle exhaust; industrial activity; and fuel oil burning. The results show that SO4(2-), OC, and crustal material are important components of PM2.5 in MMA. Further work is necessary to evaluate the proportion of secondary inorganic and organic aerosol in order to have a better understanding of the sources and precursors of aerosols in the MMA.     

Source apportionment of Phoenix PM2.5 aerosol with the Unmix receptor model

The multivariate receptor model Unmix has been used to analyze a 3-yr PM2.5 ambient aerosol data set collected in Phoenix, AZ, beginning in 1995. The analysis generated source profiles and overall average percentage source contribution estimates (SCEs) for five source categories:gasoline engines (33 +/- 4%), diesel engines (16 +/- 2%), secondary SO4(2-) (19 +/- 2%), crustal/soil (22 +/- 2%), and vegetative burning (10 +/- 2%). The Unmix analysis was supplemented with scanning electron microscopy (SEM) of a limited number of filter samples for information on possible additional low-strength sources. Except for the diesel engine source category, the Unmix SCEs were generally consistent with an earlier multivariate receptor analysis of essentially the same data using the Positive Matrix Factorization (PMF) model. This article provides the first demonstration for an urban area of the capability of the Unmix receptor model.     

Source apportionment of visual impairment during the California regional PM10/PM2.5 air quality study

Gases and particulate matter predictions from the UCD/CIT air quality model were used in a visibility model to predict source contributions to visual impairment in the San Joaquin Valley (SJV), the southern portion of California's Central Valley, during December 2000 and January 2001. Within the SJV, daytime (0800–1700 PST) light extinction was dominated by scattering associated with airborne particles. Measured daytime particle scattering coefficients were compared to predicted values at approximately 40 locations across the SJV after correction for the increased temperature and decreased relative humidity produced by “smart heaters” placed upstream of nephelometers. Mean fractional bias and mean fractional error were ?0.22 and 0.65, respectively, indicating reasonable agreement between model predictions and measurements. Particulate water, nitrate, organic matter, and ammonium were the major particulate species contributing to light scattering in the SJV. Daytime light extinction in the SJV averaged between December 25, 2000 and January 7, 2001 was mainly associated with animal ammonia sources (28%), diesel engines (18%), catalyst gasoline engines (9%), other anthropogenic sources (9%), and wood smoke (7%) with initial and boundary conditions accounting for 13%. The source apportionment results from this study apply to wintertime conditions when airborne particulate matter concentrations are typically at their annual maximum. Further study would be required to quantify source contributions to light extinction in other seasons.     

南昌市大气PM2.5中多环芳烃的来源解析

在南昌市布设5个采样点,分别代表工业区、居住区、交通干线区、商业区以及郊区,于2007年7～8月进行大气PM2.5的采样.根据5个采样点测得的数据,通过因子分析法判断南昌市大气PM2.5中多环芳烃的主要来源,再利用多元线性回归法确定各主要来源对多环芳烃的贡献率.结果表明,南昌市多环芳烃的主要来源为车辆排放源、高温加热源、燃煤污染源,对多环芳烃的贡献率分别为37.9%、28.2%、22.0%.     

Source apportionment of wintertime secondary organic aerosol during the California regional PM10/PM2.5 air quality study

The UCD/CIT air quality model with the Caltech Atmospheric Chemistry Mechanism (CACM) was used to predict source contributions to secondary organic aerosol (SOA) formation in the San Joaquin Valley (SJV) from December 15, 2000 to January 7, 2001. The predicted 24-day average SOA concentration had a maximum value of 4.26 μg m^?3 50 km southwest of Fresno. Predicted SOA concentrations at Fresno, Angiola, and Bakersfield were 2.46 μg m^?3, 1.68 μg m^?3, and 2.28 μg m^?3, respectively, accounting for 6%, 37%, and 4% of the total predicted organic aerosol. The average SOA concentration across the entire SJV was 1.35 μg m^?3, which accounts for approximately 20% of the total predicted organic aerosol. Averaged over the entire SJV, the major SOA sources were solvent use (28% of SOA), catalyst gasoline engines (25% of SOA), wood smoke (16% of SOA), non-catalyst gasoline engines (13% of SOA), and other anthropogenic sources (11% of SOA). Diesel engines were predicted to only account for approximately 2% of the total SOA formation in the SJV because they emit a small amount of volatile organic compounds relative to other sources. In terms of SOA precursors within the SJV, long-chain alkanes were predicted to be the largest SOA contributor, followed by aromatic compounds. The current study identifies the major known contributors to the SOA burden during a winter pollution episode in the SJV, with further enhancements possible as additional formation pathways are discovered.     

Source apportionment of indoor, outdoor, and personal PM2.5 in Seattle, Washington, using positive matrix factorization

As part of a large exposure assessment and health-effects panel study, 33 trace elements and light-absorbing carbon were measured on 24-hr fixed-site filter samples for particulate matter with an aerodynamic diameter <2.5 microm (PM2.5) collected between September 26, 2000, and May 25, 2001, at a central outdoor site, immediately outside each subject's residence, inside each residence, and on each subject (personal sample). Both two-way (PMF2) and three-way (PMF3) positive matrix factorization were used to deduce the sources contributing to PM2.5. Five sources contributing to the indoor and outdoor samples were identified: vegetative burning, mobile emissions, secondary sulfate, a source rich in chlorine, and a source of crustal-derived material. Vegetative burning contributed more PM2.5 mass on average than any other source in all microenvironments, with average values estimated by PMF2 and PMF3, respectively, of 7.6 and 8.7 microg/m3 for the outdoor samples, 4 and 5.3 microg/m3 for the indoor samples, and 3.8 and 3.4 microg/m3 for the personal samples. Personal exposure to the combustion-related particles was correlated with outdoor sources, whereas exposure to the crustal and chlorine-rich particles was not. Personal exposures to crustal sources were strongly associated with personal activities, especially time spent at school among the child subjects.     

Source apportionment of particulate matter (PM2.5) in an urban area using dispersion,receptor and inverse modelling

Air pollution emission inventories are the basis for air quality assessment and management strategies. The quality of the inventories is of great importance since these data are essential for air pollution impact assessments using dispersion models. In this study, the quality of the emission inventory for fine particulates (PM_2.5) is assessed: first, using the calculated source contributions from a receptor model; second, using source apportionment from a dispersion model; and third, by applying a simple inverse modelling technique which utilises multiple linear regression of the dispersion model source contributions together with the observed PM_2.5 concentrations. For the receptor modelling the chemical composition of PM_2.5 filter samples from a measurement campaign performed between January 2004 and April 2005 are analysed. Positive matrix factorisation is applied as the receptor model to detect and quantify the various source contributions. For the same observational period and site, dispersion model calculations using the Air Quality Management system, AirQUIS, are performed. The results identify significant differences between the dispersion and receptor model source apportionment, particularly for wood burning and traffic induced suspension. For wood burning the receptor model calculations are lower, by a factor of 0.54, but for the traffic induced suspension they are higher, by a factor of 7.1. Inverse modelling, based on regression of the dispersion model source contributions and the PM_2.5 concentrations, indicates similar discrepancies in the emissions inventory. In order to assess if the differences found at the one site are generally applicable throughout Oslo, the individual source category emissions are rescaled according to the receptor modelling results. These adjusted PM_2.5 concentrations are compared with measurements at four independent stations to evaluate the updated inventory. Statistical analysis shows improvement in the estimated concentrations for PM_2.5 at all sites. Similarly, inverse modelling is applied at these independent sites and this confirms the validity of the receptor model results.     

Source apportionment of fine particulate matter (PM2.5) at a rural Ohio River Valley site

Twenty four-hour averaged concentrations of fine particulate matter were collected at Athens, OH between March 2004 and November 2005 in an effort to characterize the nature of PM_2.5 and apportion its sources. PM_2.5 samples were chemically analyzed and positive matrix factorization was applied to this speciation data to identify the probable sources. PMF arrived at a 7-factor model to most accurately apportion sources of the PM_2.5 observed at Athens. Conditional probability function (CPF) and potential source contribution function (PSCF) were applied to the identified sources to investigate the geographical location of these sources. Secondary sulfate source dominated the contributions with a total contribution of 62.6% with the primary and secondary organic source following second with 19.9%. Secondary nitrate contributed a total of 6.5% with the steel production source and Pb- and Zn-source coming in at 3.1% and 2.9%, respectively. Crustal and mobile sources were small contributors (2.5% each) of PM_2.5 to the Athens region. The secondary sulfate, secondary organic and nitrate portrayed a clear seasonal nature with the sulfate and secondary organic peaking in the warm months and the nitrate reaching a high in the cold months. The high percentage of secondary sulfate observed at a rural site like Athens suggests the involvement of regional transport mechanisms.     

Chemical composition and source apportionment of PM2.5 particles in the Sihwa area, Korea

To investigate the chemical characteristics of fine particles in the Sihwa area, Korea, atmospheric aerosol samples were collected using a dichotomous PM10 sampler and two URG PM2.5 cyclone samplers during five intensive sampling periods between February 1998 and February 1999. The Inductively Coupled Plasma (ICP)-Atomic Emission Spectrometry (AES)/ICP-Mass Spectrometry (MS), ion chromatograph (IC), and thermal manganese dioxide oxidation (TMO) methods were used to analyze the trace elements, ionic species, and carbonaceous species, respectively. Backward trajectory analysis, factor analysis, and a chemical mass balance (CMB) model were used to estimate quantitatively source contributions to PM2.5 particles collected in the Sihwa area. The results of PM2.5 source apportionment using the CMB7 receptor model showed that (NH4)2SO4 was, on average, the major contributor to PM2.5 particles, followed by nontraffic organic carbon (OC) emission, NH4NO3, agricultural waste burning, motor vehicle emission, road dust, waste incineration, marine aerosol, and others. Here, the nontraffic OC sources include primary anthropogenic OC emitted from the industrial complex zone, secondary OC, and organic species from distant sources. The source impact of waste incineration emission became significant when the dominant wind directions were from southwest and west sectors during the sampling periods. It was found that PM2.5 particles in the Sihwa area were influenced mainly by both anthropogenic local sources and long-range transport and transformation of air pollutants.     

Wintertime PM2.5 and PM10 Source Apportionment at Sacramento,California

ABSTRACT

The chemical mass balance (CMB) model was applied to winter (November through January) 1991–1996 PM2.5 and PM10 data from the Sacramento 13th and T Streets site in order to identify the contributions from major source categories to peak 24-hr ambient PM_2.5 and PM₁₀ levels. The average monthly PM₁₀ monitoring data for the nine-year period in Sacramento County indicate that elevated concentrations are typical in the winter months. Concentrations on days of highest PM₁₀ are dominated by the PM2.5 fraction. One factor contributing to increased PM_2.5 concentrations in the winter is meteorology (cool temperatures, low wind speeds, low inversion layers, and more humid conditions) that favors the formation of secondary nitrate and sulfate aerosols. Residential wood burning also elevates fine particulate concentrations in the Sacramento area.

The results of the CMB analysis highlight three key points. First, the source apportionment results indicate that primary motor vehicle exhaust and wood smoke are significant sources of both PM_2.5 and PM₁₀ in winter. Second, nitrates, secondarily formed as a result of motor-vehicle and other sources of nitrogen oxide (NO_x), are another principal cause of the high PM_2.5 and PM₁₀ levels during the winter months. Third, fugitive dust, whether it is resuspended soil and dust or agricultural tillage, is not the major contributor to peak winter PM_2.5 and PM10 levels in the Sacramento area.     

Seasonal variation of chemical composition and source apportionment of PM2.5 in Pune,India

Environmental Science and Pollution Research - Particulate matter with size less than or equal to 2.5&nbsp;μm (PM2.5) samples were collected from an urban site Pune, India, during April...     

南京市气溶胶PM2.5中多环芳烃来源识别

对2005年7月至2006年2月采集到的南京市气溶胶Pm2.5 进行季节性初步分析,并对其中的15种优控多环芳烃(PAHs)进行分析研究,通过比值法判断南京市PAHs夏季主要来源于柴油型燃烧,冬季主要来源于柴油和煤型相结合的燃烧.对15种优控PAHs两两之间的相关性分析,发现各化合物之间显著相关,表明各化合物的来源有相似之处.     

Source apportionment of PM10 in six cities of northern China

Ambient PM₁₀ was sampled in six northern China cities (Urumqi, Yinchuan, Taiyuan, Anyang, Tianjin and Jinan) from December 1999 to July 2002, and analyzed for 16 chemical elements, two water-soluble ions, total carbon, and organic carbon. In addition, chemical source profiles consisting of the same particulate components were obtained from a number of naturally occurring geological sources (soil dust from exposed lands) and sources of atmospheric particulates resulting from human activities (resuspended dust, cement, coal combustion fly ash, vehicle exhaust, and secondary particles). Ambient and source data were used in a chemical mass balance (CMB) receptor model to determine the major source of PM₁₀ in these six cities. Results of CMB modeling showed that the major source of ambient PM₁₀ in all the cities was resuspended dust. Significant contributions from coal fly ash were also found in all six cities.     

Analysis of the PM2.5 emission inventory and source apportionment in Jilin City,Northeast of China

Environmental Science and Pollution Research - This study collected and compiled statistical data on atmospheric pollution in Jilin City, China during 2013–2014, using models and methods to...     

Fuel reformulation in the Metropolitan Area of Mexico City

Two models frequently used to simulate the dispersion of pollutants in the atmosphere have been compared. This is necessary because only a well-tested and well-calibrated simulation model can be a good representation of the reality of the dispersion of pollutants. The models evaluated (HYSPLIT_4 with its four variants and MEDIA) were run using as input parameters the same meteorological dataset (for 23-26 October 1994) from the French model ARPEGE. The following statistical criteria were compared: the space and time evolution of the pollutant cloud; the variation of statistical parameters in time and space; and the differences between the simulated and measured values of concentration in time for six different stations. The results emphasise the characteristics of the two models and their abilities in the framework of the air quality monitoring.     

Source apportionment of ambient PM2.5 at five spanish centres of the european community respiratory health survey (ECRHS II)

Fine particulate matter (PM_2.5) was sampled at 5 Spanish locations during the European Community Respiratory Health Survey II (ECRHS II). In an attempt to identify and quantify PM_2.5 sources, source contribution analysis by principal component analysis (PCA) was performed on five datasets containing elemental composition of PM_2.5 analysed by ED-XRF. A total of 4–5 factors were identified at each site, three of them being common to all sites (interpreted as traffic, mineral and secondary aerosols) whereas industrial sources were site-specific. Sea-salt was identified as independent source at all coastal locations except for Barcelona (where it was clustered with secondary aerosols). Despite their typically dominant coarse grain-size distribution, mineral and marine aerosols were clearly observed in PM_2.5. Multi-linear regression analysis (MLRA) was applied to the data, showing that traffic was the main source of PM_2.5 at the five sites (39–53% of PM_2.5, 5.1–12.0 μg m⁻³), while regional-scale secondary aerosols accounted for 14–34% of PM_2.5 (2.6–4.5 μg m⁻³), mineral matter for 13–31% (2.4–4.6 μg m⁻³) and sea-salt made up 3–7% of the PM_2.5 mass (0.4–1.3 μg m⁻³). Consequently, despite regional and climatic variability throughout Spain, the same four main PM_2.5 emission sources were identified at all the study sites and the differences between the relative contributions of each of these sources varied at most 20%. This would corroborate PM_2.5 as a useful parameter for health studies and environmental policy-making, owing to the fact that it is not as subject to the influence of micro-sitting as other parameters such as PM₁₀. African dust inputs were observed in the mineral source, adding on average 4–11 μg m⁻³ to the PM_2.5 daily mean during dust outbreaks. On average, levels of Al, Si, Ti and Fe during African episodes were higher by a factor of 2–8 with respect to non-African days, whereas levels of local pollutants (absorption coefficient, S, Pb, Cl) showed smaller variations (factor of 0.5–2).     

Evaluation of Human Exposure to Ambient PM10 in the Metropolitan Area of Mexico City Using a GIS-Based Methodology

ABSTRACT

The main goal of this study was to evaluate the magnitude of outdoor exposure to fine particulate matter (PM₁₀) potentially experienced by the population of metropolitan Mexico City. With the use of a geographic information system (GIS), spatially resolved PM₁₀ distributions were generated and linked to the local population. The PM₁₀ concentration exceeded the 24-hr air quality standard of 150 μg/m³ on 16% of the days, and the annual air quality standard of 50 μg/m³ was exceeded by almost twice its value in some places. The basic methodology described in this paper integrates spatial demographic and air quality databases, allowing the evaluation of various air pollution reduction scenarios. Achieving the annual air quality standard would represent a reduction in the annual arithmetic average concentration of 14 μg/m³ for the typical inhabitant. Human exposure to particulate matter (PM) has been associated with mortality and morbidity in Mexico City; reducing the concentration levels of this pollutant would represent a reduction in mortality and morbidity and the associated cost of such impacts. This methodology is critical to assessing the potential benefits of the current initiative to improve air quality implemented by the Environmental Metropolitan Commission of Mexico City.     

Source identification of nickel in TSP and PM2.5 in Tokyo,Japan

This study investigates the source identification of nickel in the aerosol of the Tokyo metropolitan area. TSP and PM_2.5 samples were collected daily from August to November 2004. The samples were examined by means of the water-extraction method, followed by elemental analysis and SEM/EDX analysis. We distinguished two types of atmospheric nickel sources in the studied area: (1) particles derived from heavy oil combustion, distributed mostly in fine particles such as PM_2.5, relatively water-soluble, and containing vanadium and (2) particles derived from mechanical abrasion/erosion of metallic surfaces, distributed in coarse particles such as TSP, relatively water-insoluble, and containing chromium.