Leaching of heavy metals from chromated copper arsenate (CCA) treated wood after disposal

Wood treated by preservatives is commonly found in solid waste. Among the different types of preserved wood, chromated copper arsenate (CCA) treated wood recently has received much attention due to the scale of usage and its significant role in soil and water contamination. As the ash of CCA treated wood would be hazardous if the wood were to be incinerated, this is not a good alternative, and the best available disposal method is thus landfilling in the US, Canada and Australia. Leaching of the metals from preserved wood that is disposed in unlined landfills for construction debris pollutes the soil and water environments. Several factors affecting leaching of the metals from wood, including pH of the leachant, temperature, the duration of leaching and the type of leachant, were investigated. These factors affect each of the metals, chromium, copper and arsenic, differently. A comparison of these effects on each metal was performed. The results of the experiments showed that the pH of the leachants has a significant effect on the leaching process, and sulfuric acid (pH 3) is the most effective leachant compared to nitric and acetic acid (pH 3-4-5). The amounts of leached chromium, copper and arsenic by sulfuric acid (pH 3) during 15 days were, respectively, 0.2, 0.14 and 0.15 mg more than leachates by nitric acid (pH 5) on the basis of 1g of wood (initial contents of 1.03 mg, 0.42 g and 0.8 mg per g of wood). Most of the leaching occurs in the first 5 days, and the rate of leaching decreases significantly after 5 days. Increasing temperature increases the amount of leached metals, and arsenic is the least resistant metal to the leaching when the temperature increases. Increasing the temperature from 15 degrees C to 35 degrees C during 15 days increases the amount of leached chromium, copper and arsenic by acetic acid at pH 5 by about 0.1, 0.4 and 1.2mg per g of wood, respectively.     

Designing a purification process for chromium-, copper- and arsenic-contaminated wood

The disposal of chromated copper arsenate (CCA)-treated wood is becoming a serious problem in many countries due to increasing levels of contamination by the hazardous elements, chromium, copper and arsenic. The present experiment was conducted as a preliminary step toward one-step solvent extraction of CCA-treated wood. Because chromium, copper and arsenic have different chemical characteristics, it is best to consider them separately prior to designing a one-step extraction process. As a basis, various two-step extraction processes were first designed and tested experimentally to determine feasibility. Among these combinations, the treatment combining oxalic acid as the 1st step and a sodium oxalate solution under acidic conditions (pH 3.2) as the 2nd step was found to be an effective way of extracting CCA elements from treated wood. Extraction efficiency reached 100% for arsenic and chromium and 95.8% for copper after a 3-h sodium oxalate treatment, following a 1-h pre-extraction process with oxalic acid. On the other hand, the same combination under alkaline conditions (pH 11.2) during the 2nd step was ineffective for copper removal, indicating that pH plays an important role in complexation with sodium oxalate solution. The present results suggest that the extraction of CCA elements using a combination of oxalic acid and acidic sodium oxalate solution is a promising basis for application to a one-step extraction method.     

Improving the two-step remediation process for CCA-treated wood: Part I. Evaluating oxalic acid extraction

In this study, three possible improvements to a remediation process for chromated-copper-arsenate- (CCA) treated wood were evaluated. The process involves two steps: oxalic acid extraction of wood fiber followed by bacterial culture with Bacillus licheniformis CC01. The three potential improvements to the oxalic acid extraction step were (1) reusing oxalic acid for multiple extractions, (2) varying the ratio of oxalic acid to wood, and (3) using a noncommercial source of oxalic acid such as Aspergillus niger, which produces oxalic acid as a metabolic byproduct. Reusing oxalic acid for multiple extractions removed significant amounts of copper, chromium, and arsenic. Increasing the ratio of wood to acid caused a steady decline in metal removal. Aspergillus niger removed moderate amounts of copper, chromium, and arsenic from CCA-treated wood. Although A. niger was effective, culture medium costs are likely to offset any benefits. Repeated extraction with commercial oxalic acid appears to be the most cost-effective method tested for the two-step process.     

Improving the two-step remediation process for CCA-treated wood: Part II. Evaluating bacterial nutrient sources

Remediation processes for recovery and reuse of chromated-copper-arsenate- (CCA) treated wood are not gaining wide acceptance because they are more expensive than landfill disposal. One reason is the high cost of the nutrient medium used to culture the metal-tolerant bacterium, Bacillus licheniformis, which removes 70-100% of the copper, chromium, and arsenic from CCA-treated southern yellow pine (CCA-SYP) in a two-step process involving oxalic acid extraction and bacterial culture. To reduce this cost, the nutrient concentration in the culture medium and the ratio of wood to nutrient medium were optimized. Maximum metal removal occurred when B. licheniformis was cultured in 1.0% nutrient medium and at a wood to nutrient medium ratio of 1:10. Also, malted barley, an abundant by-product of brewing, was evaluated as an alternative nutrient medium. Tests were done to determine absorption of metals by barley, and the results indicate that the barley acted as a biosorbent, removing heavy metals from the liquid culture after their release from CCA to SYP. For comparison, tests were also performed with no nutrient medium. Following bacterial remediation, 17% copper and 15% arsenic were removed from an aqueous slurry of CCA-SYP (no medium). When oxalic acid extraction preceded the aqueous bacterial culture, 21% copper, 54% chromium, and 63% arsenic were removed. The two-step process (oxalic acid extraction and bacterial culture with nutrient medium) appears to be an effective, yet costly, way to remove metals.     

Factors affecting sodium hypochlorite extraction of CCA from treated wood

Significant amounts of chromated copper arsenate (CCA) treated wood products, such as utility poles and residential construction wood, remain in service. There is increasing public concern about environmental contamination from CCA-treated wood when it is removed from service for reuse or recycling, placed in landfills or burned in commercial incinerators. In this paper, we investigated the effects of time, temperature and sodium hypochlorite concentration on chromium oxidation and extraction of chromated copper arsenate from CCA-treated wood (Type C) removed from service. Of the conditions evaluated, reaction of milled wood with sodium hypochlorite for one hour at room temperature followed by heating at 75 °C for two hours gave the highest extraction efficiency. An average of 95% Cr, 99% Cu and 96% As could be removed from CCA-treated, milled wood by this process. Most of the extracted chromium was oxidized to the hexavalent state and could therefore be recycled in a CCA treating solution. Sodium hypochlorite extracting solutions could be reused several times to extract CCA components from additional treated wood samples.     

Evaluation of commercial landscaping mulch for possible contamination from CCA

Wood treated with chromated copper arsenate (CCA) is found in construction and demolition (C&D) debris, and a common use for wood recycled from C&D debris is the production of mulch. Given the high metals concentrations in CCA-treated wood, a small fraction of CCA-treated wood can increase the metal concentrations in the mulch above regulatory thresholds. The objective of this study was to determine the extent of contamination of CCA-treated wood in consumer landscaping mulch and to determine whether visual methods or rapid X-ray fluorescence (XRF) technology can be used to identify suspect mulch. Samples were collected throughout the State of Florida (USA) and evaluated both visually and chemically. Visual analysis focused on documenting wood-chip size distribution, whether the samples were artificially colored, and whether they contained plywood chips which is an indication that the sample was, in part, made from recycled C&D wood. Chemical analysis included measurements of total recoverable metals, leachable metals as per the standardized synthetic precipitation leaching procedure (SPLP), and XRF analysis. Visual identification methods, such as colorant addition or presence of plywood, were found effective to preliminarily screen suspect mulch. XRF analysis was found to be effective for identifying mulch containing higher than 75 mg/kg arsenic. For mulch samples that were not colored and did not contain evidence of C&D wood, none exceeded leachable metal concentrations of 50 microg/L and only 3% exceeded 10 mg/kg for recoverable metals. The majority of the colored mulch made from recycled C&D wood contained from 1% to 5% CCA-treated wood (15% maximum fraction) resulting in leachable metals in excess of 50 microg/L and total recoverable metals in excess of 10 mg/kg. The maximum arsenic concentration measured in the mulch samples evaluated was 230 mg/kg, which was above the Florida residential direct exposure regulatory guideline of 2.1 mg/kg.     

Rapid-extraction oxidation process to recover and reuse copper chromium and arsenic from industrial wood preservative sludge

Chromated copper arsenate (CCA) wood preservative can form insoluble sludges when the hexavalent chromium component is reduced by wood extractives, wood particles and preservative additives in the solution. This sludge accumulates in treating solution work tanks, sumps and in-line filters and must be disposed of as hazardous wastes by waste disposal companies at high costs. A number of commercial sludges were investigated and found to contain 18-94% copper, chromium and arsenic as oxides combined with sand, oil, wood particles, additives and wood extractives. We have developed a multi-stage recycling process whereby approximately 97% of the CCA components are recovered from the sludge. It involves extraction with sodium hypochlorite to remove and oxidize chromium (more than 90%) and extract most of the arsenic (approx. 80%) followed by extraction of the copper and remaining arsenic and chromium with phosphoric acid. The phosphoric acid extract contains some trivalent chromium, which is subsequently oxidized by sodium hypochlorite. The combined oxidized extract containing CrVI, CuII and AsV was compatible with CCA treating solutions and could be re-used commercially for treating wood without having a significant effect on the preservative fixation rate or the leach resistance of the treated wood. A cost analysis showed that the economic savings from recovery of CCA chemicals and reduced landfill costs exceeded the variable costs for materials and energy for the process by as much as Can $966 per tonne of sludge if sodium sulfite can be acquired in bulk quantities for the process.     

CCA-treated wood disposed in landfills and life-cycle trade-offs with waste-to-energy and MSW landfill disposal

Chromated copper arsenate (CCA)-treated wood is a preservative treated wood construction product that grew in use in the 1970s for both residential and industrial applications. Although some countries have banned the use of the product for some applications, others have not, and the product continues to enter the waste stream from construction, demolition and remodeling projects. CCA-treated wood as a solid waste is managed in various ways throughout the world. In the US, CCA-treated wood is disposed primarily within landfills; however some of the wood is combusted in waste-to-energy (WTE) facilities. In other countries, the predominant disposal option for wood, sometimes including CCA-treated wood, is combustion for the production of energy. This paper presents an estimate of the quantity of CCA-treated wood entering the disposal stream in the US, as well as an examination of the trade-offs between landfilling and WTE combustion of CCA-treated wood through a life-cycle assessment and decision support tool (MSW DST). Based upon production statistics, the estimated life span and the phaseout of CCA-treated wood, recent disposal projections estimate the peak US disposal rate to occur in 2008, at 9.7 million m(3). CCA-treated wood, when disposed with construction and demolition (C&D) debris and municipal solid waste (MSW), has been found to increase arsenic and chromium concentrations in leachate. For this reason, and because MSW landfills are lined, MSW landfills have been recommended as a preferred disposal option over unlined C&D debris landfills. Between landfilling and WTE for the same mass of CCA-treated wood, WTE is more expensive (nearly twice the cost), but when operated in accordance with US Environmental Protection Agency (US EPA) regulations, it produces energy and does not emit fossil carbon emissions. If the wood is managed via WTE, less landfill area is required, which could be an influential trade-off in some countries. Although metals are concentrated in the ash in the WTE scenario, the MSW landfill scenario releases a greater amount of arsenic from leachate in a more dilute form. The WTE scenario releases more chromium from the ash on an annual basis. The WTE facility and subsequent ash disposal greatly concentrates the chromium, often oxidizing it to the more toxic and mobile Cr(VI) form. Elevated arsenic and chromium concentrations in the ash leachate may increase leachate management costs.     

Evaluation of XRF and LIBS technologies for on-line sorting of CCA-treated wood waste

Contamination of wood waste with chromated copper arsenate greatly limits recycling opportunities for the wood waste as a whole. Separation of CCA-treated wood from other wood types is one means by which such contamination can be removed. The purpose of the current study was to evaluate two detector technologies for sorting CCA-treated wood from other wood types. The detector technologies evaluated included X-ray fluorescence spectroscopy (XRF) and laser induced breakdown spectroscopy (LIBS). The XRF detector system utilized in this study was capable of rapidly detecting the presence of CCA in painted wood, wet wood, heartwood, sapwood, and at portions of the wood containing knots. Furthermore, the XRF system was capable of distinguishing between CCA-treated wood and wood treated with alternative wood treatment preservatives, but was limited by the fact that it was not designed for on-line operation so tests were conducted in a batch mode on a conveyor. The analysis time used in this study (3 s) can be decreased significantly for an XRF system designed specifically for on-line operation. The LIBS system developed for this study was found to effectively identify CCA-treated wood for pieces ranging in thickness from 1 to 8 cm. High sorting efficiencies were noted when 10 laser shots were taken on a piece of wood. Furthermore, the LIBS system was found to be effective for identifying wood that has been coated with stains and paints in addition to identifying wood that has been CCA treated. The major drawback with the LIBS system developed in this study was the limited laser pulse energy. With an increase in laser pulse energy it is anticipated that the working focal length of the LIBS system can be increased to enable the monitoring of wood samples of more variable thicknesses. Limitations associated with analysis of very rotted pieces of wood and wet wood can also be overcome by using a higher pulse energy laser. Overall, both technologies show incredible promise for sorting CCA-treated wood from other wood types. The next recommended step would be to run an improved full-scale operation at one facility to document sorting efficiencies and fine-tune the improvements proposed in the current study. Such a study could potentially open-the-door for more widespread sorting of wood waste.     

Method to recover and reuse chromated copper arsenate wood preservative from spent treated wood

The volume of chromated copper arsenate (CCA) treated wood products coming out of service is expected to increase dramatically during the next decade. There is a need for an alternative waste management approach to landfilling. This paper investigates the variables affecting extraction of CCA components from wood particles and the potential to oxidize and reuse the recovered chemicals. Most of the CCA components could be extracted by 10% H2O2 at 50 degrees C in 6 h with an average extraction efficiency of 95% for Cr, 94% for Cu and 98% for As. The extract containing Cr(III), Cu(II) and As(V) could be oxidized in several stages by aqueous 2.5% w/w H2O2 in less than 2 h to a condition where it was compatible with CCA treating solutions and could be reused for treating new wood. When the recovered extract was mixed with fresh CCA solution in different ratios, the mixed CCA-C solutions had similar solution stability as freshly prepared CCA-C solution and treated wood had similar leaching properties as wood treated with fresh solution.     

Online sorting of recovered wood waste by automated XRF-technology. Part I: detection of preservative-treated wood waste

Waste wood is frequently contaminated with wood treatment preservatives including chromated copper arsenate (CCA) and alkaline copper quat (ACQ), both of which contain metals which contaminate recycled wood products. The objective of this research was to propose a design for online automated identification of As-based and Cu-based treated wood within the recovered wood waste stream utilizing an X-ray fluorescence (XRF) system, and to evaluate the detection parameters of such system. A full-scale detection unit was used for experimentation. Two main parameters (operational threshold (OT) and measurement time) were evaluated to optimize detection efficiencies. OTs of targeted metals, As and Cu, in wood were reduced to 0.02 and 0.05, respectively. The optimum minimum measurement time of 500 ms resulted in 98%, 91%, and 97% diversion of the As, Cu and Cr mass originally contained in wood, respectively. Comparisons with other detection methods show that XRF technology can potentially fulfill the need for cost-effective processing at large facilities (>30 tons per day) which require the removal of As-based preservatives from their wood waste stream.     

Calcium phosphate stabilization of fly ash with chloride extraction

Municipal solid waste incinerator by products include fly ash and air pollution control residues. In order to transform these incinerator wastes into reusable mineral species, soluble alkali chlorides must be separated and toxic trace elements must be stabilized in insoluble form. We show that alkali chlorides can be extracted efficiently in an aqueous extraction step combining a calcium phosphate gel precipitation. In such a process, sodium and potassium chlorides are obtained free from calcium salts, and the trace metal ions are immobilized in the calcium phosphate matrix. Moderate calcination of the chemically treated fly ash leads to the formation of cristalline hydroxylapatite. Fly ash spiked with copper ions and treated by this process shows improved stability of metal ions. Leaching tests with water or EDTA reveal a significant drop in metal ion dissolution. Hydroxylapatite may trap toxic metals and also prevent their evaporation during thermal treatments. Incinerator fly ash together with air pollution control residues, treated by the combined chloride extraction and hydroxylapatite formation process may be considered safe to use as a mineral filler in value added products such as road base or cement blocks.     

Influence of corn steep liquor and glucose on colonization of control and CCB (Cu/Cr/B)-treated wood by brown rot fungi

There are increasing problems with regard to the disposal of treated wood waste. Due to heavy metals or arsenic in impregnated wood waste, burning and landfill disposal options are not considered to be environmentally friendly solutions for dealing with this problem. Extraction of the heavy metals and recycling of the preservatives from the wood waste is a much more promising and environmentally friendly solution. In order to study the scale up of this process, copper/chromium/boron-treated wood specimens were exposed to copper tolerant (Antrodia vaillantii and Leucogyrophana pinastri) and copper sensitive wood decay fungi (Gloeophyllum trabeum and Poria monticola). Afterwards, the ability of fungal hyphae to penetrate and overgrow the wood specimens was investigated. The fungal growths were stimulated by immersing the specimens into aqueous solution of glucose or corn steep liquor prior to exposure to the fungi. The fastest colonization of the impregnated wood was by the copper tolerant A. vaillantii. Addition of glucose onto the surface of the wood specimens increased the fungi colonization of the specimens; however, immersion of the specimens into the solution of corn steep liquor did not have the same positive influence. These results are important in elucidating copper toxicity in wood decay fungi and for using these fungi for bioremediation of treated wood wastes.     

Removal of copper,chromium and arsenic from preservative-treated wood by chemical extraction-fungal bioleaching

Large volumes of preservative-treated wood containing toxic Cr, Cu and As salts are decommissioned worldwide. This study investigated the effectiveness of solid-state fermentation with copper-tolerant brown-rot fungi for the remediation of wood treated with chromated copper arsenate (CCA) and acid copper chromate (ACC) formulations. Treatment of CCA- and ACC-wood with the most effective strain, Antrodia vaillantii FRLP-14G, attained extensive leaching of As and/or Cr, but Cu elimination was poor (<18%). Additional research showed that a variety of organic acids, including citrate, are effective Cu extractants. Based on these findings, a process combining chemical extraction and subsequent fungal treatment was developed that proved highly effective in removing inorganic pollutants from CCA-wood. Extraction of CCA-wood with citric acid (30 mM, pH 3.10) followed by a 28-day solid-state fermentation period removed 87% Cu, 80% Cr, and 100% As. These results indicate the potential of the two-stage process for the remediation of preservative-treated wood.     

THE POTENTIAL FOR RE-USE OF PRESERVATIVE-TREATED UTILITY POLES REMOVED FROM SERVICE

This study investigates the feasibility of re-using or recycling utility poles or parts of poles for solid wood products. Four hundred and fifty-six poles or pole sections, removed from service in Ontario and Quebec, Canada, were characterized by age, wood species, preservative type, residual preservative, dimensions and condition. Based on this characterization, the potential for re-use as round poles or posts, sawn posts, timber, lumber and cedar roof shingles was evaluated. About 8% of the poles can be re-used without reprocessing, 15% of the pole volume can be used for cedar shingles, and about 35% of the pole volume can be converted to sawn products based on the selected hierarchy of preferred uses. Most of the poles removed from service had been treated with pentachlorophenol. The average levels of treatment decreased with age of the poles and approached the toxic threshold retentions in 25-year-old (or older) poles. For older poles (>35 years), creosote was the predominant treatment. Creosote levels were about 50% of the assumed levels when fresh treated. Creosote extracted from these poles contained fewer polynuclear aromatic hydrocarbon components than “new” creosote. The poles treated with chromated copper arsenate (CCA) retained high levels of preservative, even after many years in service. Used poles can be sawn into lumber of a good grade (#2 and better) using a small portable bandsaw. Special sawdust handling and disposal provisions must be made if this use is to be adopted. Treated poles with depleted reserves of creosote or pentachlorophenol could be re-treated with CCA or creosote preservatives to acceptable retentions. The quality of re-treatment was as good or better than that observed with new wood, and the re-treatment should ensure several decades of protection for guide-rail posts and other high decay hazard applications.     

Evaluation of methods for sorting CCA-treated wood

Construction and demolition (C&D) wood frequently contains treated wood including wood treated with chromated copper arsenate (CCA). Many recycling options for such wood require that the product be essentially free of preservative chemicals. The objectives of this study were to document the characteristics of the wood waste stream and to evaluate the effectiveness of sorting methods for identifying treated wood. Sorting methods evaluated included visual sorting and visual sorting augmented with the use of PAN indicator stain and/or hand-held X-ray fluorescence (XRF) units. Experiments were conducted on two types of construction and demolition (C&D) wood: source separated loads containing only C&D wood and wood hand-picked from commingled loads of general C&D waste. Results showed that 77% of the treated wood was CCA-treated. For uncontaminated piles (<1% treated wood) of source separated C&D wood, visual sorting was found to effectively remove the small amounts of treated wood present. For piles of source separated wood that were contaminated (approximately 50% treated wood), visual sorts were not accurate and benefited from augmented sorting using PAN indicator stain. The handheld XRF devices were found to be effective for sorting commingled C&D wood, as PAN indicator stain was not as effective due to the excessive amount of surface dirt associated with commingled wood waste. Visual sorting of source separated wood was estimated to cost between US$21 to US$96 per metric ton. These costs depended upon the amount of treated wood and whether or not augmentation with PAN indicator was necessary. Visual sorting augmented with hand-held XRF units was estimated at US$113 per metric ton. The bulk of these costs were associated with labor. Future efforts should focus on reducing labor costs by mounting automated XRF units on conveyor systems.     

Conversion of CCA-treated wood to ethanol: a method to reduce leaching of metals from disposed treated wood prior to disposal

The objective of this paper is to evaluate the feasibility of producing ethanol from CCA-treated wood that is highly leachable. Following the initial tests, CCA-treated wood was hydrolysed and fermented and the results showed not only that ethanol was produced during the fermentation process but that metals were taken up by the yeast. Toxicity characteristic leaching procedure tests of the hydrolysed wood leached less than 4 mg/L of As while minimal amounts of Cr and Cu remained in the hydrolysed wood which makes landfilling of hydrolysed wood acceptable and less hazardous. A slightly lower amount of ethanol from CCA-treated than untreated wood was produced (6 and 7 g/L, respectively). In general, it suggests that production of ethanol as a source of energy from a hazardous waste (CCA-treated wood) is feasible.     

Concentrations of organic wood preservatives in wood chips produced from wood wastes

We investigated the concentrations of wood preservatives in the wood chips produced in wood-waste processing facilities in 1988, 1998–1999, and 2001–2002. Among the wood preservatives used in the past in Japan, halophenols, including PCP, chlordane, and chlorpyrifos, had comparatively high detection rates and high average concentrations in the wood chips produced in 2001–2002. Aldrin and endrin were rarely detected, and DDT was already in low concentrations in those wood chips. Although several types of wood preservative were contained in the wood chips, their concentration levels depended on the sources of the wood wastes. In chips produced from wooden pallets, wooden forms for concrete working, or wood discarded from nondemolition sources, no organochlorine wood preservatives were detected, and chlorpyrifos and chlorophenols were detected at one order of magnitude lower than the average concentrations in chips produced from wood wastes discarded in house demolitions.     

Online sorting of recovered wood waste by automated XRF-technology: part II. Sorting efficiencies

Sorting of waste wood is an important process practiced at recycling facilities in order to detect and divert contaminants from recycled wood products. Contaminants of concern include arsenic, chromium and copper found in chemically preserved wood. The objective of this research was to evaluate the sorting efficiencies of both treated and untreated parts of the wood waste stream, and metal (As, Cr and Cu) mass recoveries by the use of automated X-ray fluorescence (XRF) systems. A full-scale system was used for experimentation. This unit consisted of an XRF-detection chamber mounted on the top of a conveyor and a pneumatic slide-way diverter which sorted wood into presumed treated and presumed untreated piles. A randomized block design was used to evaluate the operational conveyance parameters of the system, including wood feed rate and conveyor belt speed. Results indicated that online sorting efficiencies of waste wood by XRF technology were high based on number and weight of pieces (70-87% and 75-92% for treated wood and 66-97% and 68-96% for untreated wood, respectively). These sorting efficiencies achieved mass recovery for metals of 81-99% for As, 75-95% for Cu and 82-99% of Cr. The incorrect sorting of wood was attributed almost equally to deficiencies in the detection and conveyance/diversion systems. Even with its deficiencies, the system was capable of producing a recyclable portion that met residential soil quality levels established for Florida, for an infeed that contained 5% of treated wood.     

Exergy analysis of the Chartherm process for energy valorization and material recuperation of chromated copper arsenate (CCA) treated wood waste

The Chartherm process (Thermya, Bordeaux, France) is a thermochemical conversion process to treat chromated copper arsenate (CCA) impregnated wood waste. The process aims at maximum energy valorization and material recuperation by combining the principles of low-temperature slow pyrolysis and distillation in a smart way. The main objective of the exergy analysis presented in this paper is to find the critical points in the Chartherm process where it is necessary to apply some measures in order to reduce exergy consumption and to make energy use more economic and efficient. It is found that the process efficiency can be increased with 2.3-4.2% by using the heat lost by the reactor, implementing a combined heat and power (CHP) system, or recuperating the waste heat from the exhaust gases to preheat the product gas. Furthermore, a comparison between the exergetic performances of a ‘chartherisation’ reactor and an idealized gasification reactor shows that both reactors destroy about the same amount of exergy (i.e. 3500 kW kg_wood⁻¹) during thermochemical conversion of CCA-treated wood. However, the Chartherm process possesses additional capabilities with respect to arsenic and tar treatment, as well as the extra benefit of recuperating materials.