Observations of Dust-Storms in China, Mongolia and Associated Dust Falls in Korea in Spring 2003

A joint monitoring of dust-storms that occurred in East Asia from March until May 2003 has been carried. Our discussions include dust-storm observations in the source areas of China and Mongolia, and measurements with satellites and ground monitors in central Korea. Differences were found in the definition and measurement of dust-storms. Over the source area of Mongolia there were 6 dusty days in March, 18 days in April, and 10 dusty days in May. In Inner Mongolia of northern China there were 4 dust-storms with 14 dusty days observed over the three months. In central Korea, a sink area, there were 4 cases of weak dust-storm and 17 dusty days in the spring of 2003. The highest PM10 value was 607 μgm⁻³ and PM 2.3 was 149 μgm⁻³, respectively. These observations identify the growing need for further universal observation practices and dust-storm reporting in future. Observations indicated that snow covered the central part of the Gobi Desert, near the boundary of China and Mongolia, from December until mid-March. This is in contrast to other years when the Gobi was relatively wet, producing unfavourable conditions for the formation of intense dust-storms. In addition, the very strong winds associated with intense cyclones and anticyclones were not apparent and the systems shifted northward during the spring. As a result, the frequency and intensity of observed dust-storms in 2003 in this region were very low. This confirms that there is variability in the frequency of dust-storm formation due to the current process of desertification and climate change.     

粉煤灰处理阴离子表面活性剂废水及机理研究

采用粉煤灰作为吸附混凝剂,研究了粉煤灰对废水中阴离子表面活性剂十二烷基磺酸钠（SDS）的去除及机理。分析了粉煤灰投加量、吸附时间、pH值对废水中SDS去除率的影响,探讨了最佳条件下废水中SDS去除率,研究了粉煤灰动力学特征。结果表明,在200mL浓度50mg/L的SDS溶液中,调节pH值为13,加入70 g粉煤灰,搅拌20m in后,SDS的去除率为83.3%。粉煤灰对SDS的吸附符合Freund lich吸附等温式。     

Thermal and Mechanical Properties of Plastics Molded from Sodium Dodecyl Sulfate-Modified Soy Protein Isolates

Soybean protein is a potential material for manufacturing of biodegradable plastics. The objective of this investigation was to characterize the thermal and mechanical properties of plastics made from sodium dodecyl sulfate (SDS)-modified soy proteins. Soy protein isolate (SPI) was prepared from defatted soy flour, modified with various concentrations of SDS, and then molded into plastics. The temperatures of denaturation of the modified soy protein increased at low SDS concentration and then decreased at high SDS concentration. At the same SDS concentration, the plastics molded from the modified soy proteins showed a similar temperature of denaturation, but a lower enthalpy of denaturation compared to the modified soy protein. Young's modulus of the plastics decreased as SDS concentration increased, and the tensile strength and strain at break of the plastics reached a maximum value at 1% SDS modification. Two glass transition temperatures were identified corresponding to the 7S and 11S globulins in SPI by dynamic mechanical analysis, and they decreased as SDS concentration increased. The SDS modification increased the water absorption of the plastics.     

Atmospheric Loadings,Concentrations and Visibility Associated with Sandstorms: Satellite and Meteorological Analysis

This Korea-China study monitored the phenomena of sandstorms and significant dustfall (SD) from 1997 to 2000. The analysis of our data included ground measurements of dust concentration, visibility, satellite imagery, aircraft and lidar observations. In addition, an estimation of atmospheric loadings and a studyon the relationship between dust concentrations and visibilitywere carried out. The movement and invasion of dust clouds toKorea were clearly identified with meteorological and satellitedata. The increasing concentrations of TSP and PM₁₀ concurredwell with the satellite information. From case studies, weestimated that atmospheric loadings of a dust cloud were over 1million ton and that the deposition over the Korean Peninsulawas in the range from 46 000 to 86 000 tons. For SD withvisibility of 3 km, we predict TSP 659 g m^-3 and PM₁₀ 493 g m^-3. We recommend the issuance of an SD Watch(advisory) and an SD Warning for the general public.     

An evaluation of legislative measures on electrical and electronic waste in the People's Republic of China

With the increasing number of recycling mishaps in connection with waste electronic and electrical equipment (WEEE) in the People's Republic of China, it is imperative that the handling and recycling of WEEE be sufficiently regulated in China. Regulations covering three major issues, namely, take-back issues, controls on hazardous substances in WEEE and the assurance of good environmental management in WEEE plants, were promulgated between 2006 and 2008. The evaluation in this country report shows that few of these regulatory measures have performed satisfactorily in terms of enforcement, of public acceptance and of environmental concerns. In brief, the take-back requirements and the associated financial responsibilities are only vaguely defined; the control on hazardous substances and the so-called "environmental expiry date" requirements cannot be properly enforced, and the resources needed to ensure the satisfactory enforcement of the environmental abatement and pollution control requirements in WEEE plants are overwhelming. In addition, the use of a "multiple enforcement body" approach to the control of hazardous substances in WEEE is an indication that the Chinese government lacks the determination to properly enforce the relevant legal requirements.     

表面活性剂对土壤中石油污染物的解吸

采用4种表面活性剂解吸老化石油污染土壤中的污染物,对其解吸动力学特征及残油组分进行了分析。实验结果表明:在表面活性剂质量浓度相同(0.5 g/L)条件下,土壤中石油污染物解吸率的大小顺序为十二烷基硫酸钠(SDS)曲拉通X-100(TX-100)吐温-80(TW-80)十二烷基苯磺酸钠(SDBS);SDS的解吸率最高,经48 h累积解吸后土壤中石油污染物的解吸率为38.7%;表面活性剂对石油污染物的解吸动力学曲线用Elovich方程拟合,效果最好,相关系数为0.970 2~0.995 6;非离子表面活性剂(TX-100、TW-80)对石油污染物中饱和烃组分的解吸率优于阴离子表面活性剂(SDS、SDBS),而对芳香烃组分的解吸率不如阴离子表面活性剂。     

Anthropogenic metal cycles in China

The flows and stocks of seven important industrial metals were characterized for mainland China for several years in the dynamically changing decade of 1994–2004. One-year snapshot cycles are provided for chromium, nickel, and silver. For copper, zinc, lead, and iron, multiple-year cycles have been completed; they demonstrate that the flows of these metals into use in China doubled between 2000 and 2004. Although the Chinese per capita flows from production to disposal are mostly shown to be below the global average rate, they are increasing or are expected to increase dramatically. The metal resource efficiency is evaluated for several indicators of material flow analysis; these metrics for China are also below the global average values. The research quantitatively illustrates that China’s metal cycles may pose significant resource and environmental challenges in terms of their magnitudes and potential for growth.     

Preparation and Characterization of Collagens from the Skin of Northern Snakehead (<Emphasis Type="Italic">Channa argus)</Emphasis>

Channa argus, a type of snakehead fish native to China, is a popular food fish in certain Asian countries but is a known destructive invasive species in the US. In this study, the two collagens, i.e. acid-soluble collagen (ASC) and pepsin-solubilized collagen (PSC), were obtained from C. argus skin. The yield of ASC was 28.0% and that of PSC was 16.8% on the dry bases. The collagens were identified as the collagen of type I by SDS–PAGE patterns. The Tds were approximately 27.0?°C. Similar ultraviolet spectra of both collagens were observed. Fourier Transform infrared spectra indicated PSC structure had a little change due to the loss of terminal domains by pepsin digestion. The results of XRD proved that the two collagens retained their helical structures. The results suggest that the collagens isolated from C. argus can potentially be alternative sources of vertebrate collagens for use in the food and other industries.     

Electrical and electronic waste management in China: progress and the barriers to overcome.

Serious adverse impacts on the environment and human health from e-waste recycling have occurred in the past and continue to occur in China today, due to a lack of national management strategies. China has made great efforts to face the challenges of the approaching peak increase in the domestic generation of e-waste and the illegal shipment of e-waste from other countries. This study examined recent progress and analysed the main problems associated with this issue in China. It was found that the material and the financial flows of e-waste in China had their own specific characteristics. Nearly 60% of the generated e-wastes were sold to private individual collectors and passed into informal recycling processes. More than 90% of Chinese citizens are reluctant to pay for the recycling of their e-waste. This is due to their traditional understanding that there remained value in these end-of-life products. Regulations concerning e-waste in China have been drafted but their deficiencies are obvious. The extended producer responsibilities (EPR) have been introduced but are not well defined. Eight formal facilities have been planned and are under construction or are in operation along the eastern coast of China but it will be difficult for them to compete with the informal processes for the reasons identified during the study.     

Environmental Conditions of Dust Events in Northern China during 2000–2001

To investigate the large-scale environmental conditions of duststorms occurring in Northern China, a synoptic situation of tendust events in Northern China during 2000–2001 was composed andits dynamic features were identified. The composite synoptic situation showed that the occurrence of the ten dust events was associated with the eastward movement of a strong cold high fromMongolia, and the development of a cyclone in Northeast China, which caused the pressure gradient to intensify considerably in Northern China. The upper level circulation revealed that a 500 hPa trough developed rapidly above Northern China, and diagnosis showed that composite ascending motion was pronouncedabove the Siberian district. The change of vertical motion in themiddle and low troposphere above Mongolia was also related to theoccurrence of the ten dust events. When the descendingcurrent, 12 hr before the occurrence, was completely replacedby the ascending current, the instable atmospheric stratificationof the lower troposphere enabled dry dust to be transported from the surface to high altitudes toward Northern China.     

表面活性剂与柠檬酸联合洗涤高黏性土壤中的重金属

以一水合柠檬酸（CA）为洗涤剂,分别采用吐温80（TW80）、十二烷基磺酸钠（SDS）、β-环糊精（BCD）和腐植酸（HA）4种表面活性剂与CA联合洗涤高黏性土壤中的重金属,考察表面活性剂与CA的联合洗脱效果。实验结果表明：添加4种表面活性剂均可提高CA对Cu、Zn和Pb的去除率;处理时无需调节体系pH;在表面活性剂与CA的混合液与土壤的液固比为10:1（mL/g）的条件下,采用一次洗涤即可。经4种表面活性剂与CA联合洗涤后,土壤中Cu、Zn和Pb的离子交换态、碳酸盐结合态和铁锰氧化结合态的占比均下降,而硫化物及有机结合态和残渣态的占比有所提升。     

Removal of copper ions and dissolved phenol from water using micellar-enhanced ultrafiltration with mixed surfactants

A laboratory study was conducted to evaluate the effects of composition and concentration of mixed anionic/nonionic surfactants on the efficiency of a micellar-enhanced ultrafiltration (MEUF) operation in removing metal ions/organic solutes from aqueous solutions. Based on the analysis of surface tensions and micelle sizes, it was found that for mixed sodium dodecylsulfate (SDS)/Triton X-100 surfactants, the critical micelle concentration (cmc) was significantly lower than that of SDS and mixed micelles formed. The mixed surfactant system was then applied in a cross-flow mode of MEUF, in which the concentration polarization can be neglected, to remove Cu2+ from aqueous solutions. With a surfactant concentration of 10 mM, the Cu2+ rejection was negligible by using pure Triton X-100 and increased with increasing SDS mole fraction with a value as high as 85%, which suggests that the rejection of Cu2+ was due to the electrostatic attraction between Cu2+ and SDS. Furthermore, pronounced Cu2+ rejection was obtained for a 5 mM SDS solution, which was attributable to a decrease in the cmc of SDS by the existence of Cu2+. When the MEUF technique was applied to remove Cu2+ and phenol simultaneously from aqueous solutions, the Cu2+ rejection was slightly enhanced in the presence of phenol. However, the rejection of phenol was comparatively low, approximately 27%, which may be caused by its relatively hydrophilic characteristic.     

微纳米气泡耦合过渡金属离子催化氧化吸收甲醛

利用过渡金属离子Fe^2+和Mn^2+作为催化剂,耦合微纳米气泡催化氧化吸收HCHO,研究了各种反应参数变化对吸收效果的影响,并借助GC-MS技术探究了微纳米气泡氧化吸收HCHO的机理。实验结果表明:HCHO吸收率随着吸收液pH、NaCl浓度、SDS浓度及过渡金属离子浓度的增加均呈现出先升高后降低的变化规律,低浓度的NaCl有助于HCHO的吸收;在进气HCHO质量浓度0.4 mg/m^3、循环9次的设定工况下,最佳工艺条件为吸收液pH 4、NaCl质量浓度0.1 g/L、SDS质量浓度7 mg/L、Fe^2+/Mn^2+浓度2.0 mmol/L;在此条件下,Fe^2+和Mn^2+催化体系的HCHO吸收率分别达82.6%和90.4%。GC-MS分析结果显示,微纳米气泡氧化吸收HCHO的主要有机产物为乙二醇。     

Use of biosurfactants from urban wastes compost in textile dyeing and soil remediation

A compost isolated humic acid-like (cHAL) material was pointed out in previous work for its potential as auxiliary in chemical technology. Its potential is based on its relatively low 0.4gL(-1) critical micellar concentration (cmc) in water, which enables cHAL to enhance the water solubility of hydrophobic substances, like phenanthrene, when used at higher concentrations than 0.4gL(-1). This material could be obtained from a 1:1 v/v mixture of municipal solid and lignocellulosic wastes composted for 15 days. The compost, containing 69.3% volatile solids, 39.6% total organic C and 21C/N ratio, was extracted for 24h at 65 degrees C under N2 with aqueous 0.1molL(-1) NaOH and 0.1molL(-1) Na4P2O7, and the solution was acidified to separate the precipitated cHAL in 12% yield from soluble carbohydrates and other humic and non-humic substances. In this work two typical applications of surfactants, i.e., textile dyeing (TD) and soil remediation by washing (SW), were chosen as grounds for testing the performance of the cHAL biosurfactant against the one of sodium dodecylsulfate (SDS), which is a well established commercial synthetic surfactant. The TD trials were carried out with nylon 6 microfiber and a water insoluble dye, while the SW tests were performed with two soils contaminated by polycyclic aromatic hydrocarbons (PAH) for several decades. Performances were rated in the TD experiments based on the fabric colour intensity (DeltaE) and uniformity (sigmaDeltaE), and in the SW experiments based on the total hydrocarbons concentration (CWPAH) and on the residual surfactant (Cre) concentrations in the washing solution equilibrated with the contaminated soils. The results show that both cHAL and SDS exhibit enhanced performance when applied above their cmc values. However, while in the TD case a significant performance effect was observed at the surfactants cmc value, in the SW case the required surfactants concentration values were equivalent to 25-125xcmc for cHAL and to 4-22xcmc for SDS. The vis-a-vis comparison of the two surfactants gave the following results: in the TD case the cHAL biosurfactant at 0.4gL(-1) yields good colour intensity and equal colour uniformity as SDS at 5gL(-1), in the SW case cHAL was found to enhance CWPAH by a factor of 2-4 relative to SDS with one soil, whereas with the other soil the two surfactants behaved similarly. The Cre data, however, showed that both soils absorbed by far more SDS (68-95%) than cHAL (12-54%). The results point out intriguing technological and environmental perspectives deriving from the use of compost isolated biosurfactants in the place of synthetic surfactants.     

Waste incineration,PVC, and dioxins

Waste incineration is becoming increasingly necessary to tackle the rapidly rising amounts of municipal solid waste (MSW); in China many large cities are already surrounded by a girdle of landfills. Still, the not-in-my-backyard (nimby) syndrome holds strong. This attitude stems from fear of dioxins. These have been associated with incineration (‘dioxin factories’) and at times also with polyvinylchloride. In this paper this issue is analysed. China should build additional trust in MSW incineration, following promulgation of stricter emission standards, enforced by stringent controls.     

Wet Strength and Water Resistance of Modified Soy Protein Adhesives and Effects of Drying Treatment

Soy protein isolate (SPI) was modified using sodium dodecyl sulfate (SDS) and guanidine hydrochloride (GuHCl). Adhesion performance of the modified SPI on fiberboard was studied. The Water-soluble mass of the modified SPI adhesives was examined following modified ASTM D5570. The SDS-modified SPI containing 91% protein had a water-soluble mass of 1.7%. To be considered a water-resistant adhesive, the water-soluble mass of adhesive should be less than 2%. The wet shear strength test showed 100% cohesive failure within fiberboard, indicating that the modified SPI has good water resistance. The effect of drying treatment on adhesion performance of the SDS-modified SPI on fiberboard was then investigated. Drying treatment significantly affected the final adhesion performance. Shear strength did not change much, but the percentage of cohesive failure within fiberboard increased markedly as drying temperature increased. All the unsoaked, soaked, and wet specimens glued by the adhesives treated at 70° or 90°C had 100% cohesive failure within fiberboard. Viscosity also increased greatly with an increase in drying temperature. This information will be useful in developing low-cost adhesive processing system in the future.     

The development of agro-residue densified fuel in China based on energetics analysis

Agro-residue is one of the important biomass resources in China and its efficient utilization is crucial for providing bio-energy, releasing risk of environmental pollution, and enhancing rural incomes. Densification is one of the important utilization routes of agro-residues. The objective of this paper is to explore the development of agro-residue densified fuel in China based on energetics analysis. The energetical property and energy potential of main agro-residues in China were firstly analyzed and then the development of agro-residue densified fuel in every region was evaluated based on energetics analysis. The results show that the main agro-residues in China are good feedstocks as densified fuel and they constitute enormous energy potential for developing densified fuel. However, the situation of every region should be considered for the development of agro-residue densified fuel. The primary energy embodied per unit of useful energy indicates that most of the regions in China are suitable for developing agro-residue densified fuel as it is energetically advantageous compared with coal, whereas only about 25% of regions near coal production locations are not suitable as they are less energetically advantageous.     

An empirical investigation of construction and demolition waste generation rates in Shenzhen city, South China

The construction and demolition waste generation rates (C&D WGRs) is an important factor in decision-making and management of material waste in any construction site. The present study investigated WGRs by conducting on-site waste sorting and weighing in four ongoing construction projects in Shenzhen city of South China. The results revealed that WGRs ranged from 3.275 to 8.791 kg/m² and miscellaneous waste, timber for formwork and falsework, and concrete were the three largest components amongst the generated waste. Based on the WGRs derived from the research, the paper also discussed the main causes of waste in the construction industry and attempted to connect waste generation with specific construction practices. It was recommended that measures mainly including performing waste sorting at source, employing skilful workers, uploading and storing materials properly, promoting waste management capacity, replacing current timber formwork with metal formwork and launching an incentive reward program to encourage waste reduction could be potential solutions to reducing current WGRs in Shenzhen. Although these results were derived from a relatively small sample and so cannot justifiably be generalized, they do however add to the body of knowledge that is currently available for understanding the status of the art of C&D waste management in China.     

Recovery of zinc and lead from fly ash from ash-melting and gasification-melting processes of MSW--comparison and applicability of chemical leaching methods

Fly ash generated from MSW ash-melting and gasification-melting plants, known as Melting Furnace Fly Ash (MFA), contains considerable amounts of heavy metals such as Pb and Zn. These metals can be recovered using a smelting furnace after "pre-treatment" for removal of unnecessary elements such as Cl, Sn and Si. Chemical methods have been studied for pretreatment in the past. However, they have been discussed only with regard to treatment cost and the concentration of Pb and Zn recovered, but neither applicability to various types of MFA nor the environmental impact have been considered. In this study, acid, alkaline and ammonia/chloride leaching methods were compared from the standpoints of: (1) applicability to MFA, (2) concentration of Pb and Zn recovered, (3) treatment cost, and (4) environmental impact. Twenty-three samples of MFAs were collected and classified into 4 types based on element contents. A Pb and Zn recovery experiment was conducted for the representative MFA of those types. The results showed: (1) MFA from gasification-melting plants cannot be treated by chemical methods; (2) the other MFA can be treated to an acceptable quality by existing smelting furnaces; (3) only MFA from electric resistance ash-melting plants can be treated easily by the water washing method; and (4) alkaline and ammonia/chloride leaching methods were more effective than acid leaching.     

Review and prospect of emerging contaminants in waste – Key issues and challenges linked to their presence in waste treatment schemes: General aspects and focus on nanoparticles

The presence in waste of emerging pollutants (EPs), whose behaviours and effects are not well understood, may present unexpected health and environmental risks and risks for the treatment processes themselves. EP may include substances that are newly detected in the environment, substances already identified as risky and whose use in items is prohibited (but which may be present in old or imported product waste) or substances already known but whose recent use in products can cause problems during their future treatment as waste. Several scientific studies have been conducted to assess the presence of EP in waste, but they are mostly dedicated to a single category of substance or one particular waste treatment. In the absence of a comprehensive review focused on the impact of the presence of EP on waste treatment schemes, the authors present a review of the key issues associated with the treatment of waste containing emerging pollutants. This review presents the typologies of emerging pollutants that are potentially present in waste along with the major challenges for each treatment scheme (recycling, composting, digestion, incineration, landfilling and wastewater treatment). All conventional treatment processes are affected by these new pollutants, and they were almost never originally designed to consider these substances. In addition to these general aspects, a comprehensive review of available data, projects and future R&D needs related to the impact of nanoparticles on waste treatment is presented as a case study.