Reusing H2S-exhausted carbon as packing material for odor biofiltration

Exhausted carbon coming from the H2S adsorption process is a big environmental problem in Wastewater Treatment Plants. In this study, reusing exhausted carbon as a carrier of sulfide-oxidizing bacteria in lab-scale biofilters was evaluated. The exhausted carbons from different heights of the adsorption bed have different exhaustion extents, i.e. characteristics in terms of sulfur content, pH and porosity. Therefore, four biofilters were packed separately with exhausted carbon from top, middle, bottom of H2S adsorption bed, and a mixture of the three, to investigate the suitability for further H2S biofiltration. The results showed a quick startup in these biofilters (approximately 80 h). The numbers of sulfide-oxidizing bacteria immobilized on activated carbon were approximately 4.8, 9.2 and 14 x 108 CFU g-1 top, middle and bottom carbon after the 240-h operation, respectively. In addition, the biofilters demonstrated a rapid recovery to the original removal efficiency (RE) within 2 h after the H2S spike loadings. After a 110-h shutdown, the RE was rapidly recovered for all the biofilters within 5 h, with a shorter time (1 h) observed for the bottom carbon biofilter. The H2S removal mechanism of these biofilters was studied through a full analysis of sulfur products in both liquid (recycling medium) and activated carbon, and variable characterization of activated carbon before and after biofiltration. This study shows that the exhausted carbon-based biofilter is a feasible and economical alternative to conventional odor biofiltration.     

Removal of carbonyl sulfide using activated carbon adsorption

Wastewater treatment plant odors are caused by compounds such as hydrogen sulfide (H2S), methyl mercaptans, and carbonyl sulfide (COS). One of the most efficient odor control processes is activated carbon adsorption; however, very few studies have been conducted on COS adsorption. COS is not only an odor causing compound but is also listed in the Clean Air Act as a hazardous air pollutant. Objectives of this study were to determine the following: (1) the adsorption capacity of 3 different carbons for COS removal; (2) the impact of relative humidity (RH) on COS adsorption; (3) the extent of competitive adsorption of COS in the presence of H2S; and (4) whether ammonia injection would increase COS adsorption capacity. Vapor phase react (VPR; reactivated), BPL (bituminous coal-based), and Centaur (physically modified to enhance H2S adsorption) carbons manufactured by Calgon Carbon Corp. were tested in three laboratory-scale columns, 6 in. in depth and 1 in. in diameter. Inlet COS concentrations varied from 35 to 49 ppmv (86-120 mg/m3). RHs of 17%, 30%, 50%, and 90% were tested. For competitive adsorption studies, H2S was tested at 60 ppmv, with COS at 30 ppmv. COS, RH, H2S, and ammonia concentrations were measured using an International Sensor Technology Model IQ-350 solid state sensor, Cole-Parmer humidity stick, Interscan Corp. 1000 series portable analyzer, and Drager Accuro ammonia sensor, respectively. It was found that the adsorption capacity of Centaur carbon for COS was higher than the other two carbons, regardless of RH. As humidity increased, the percentage of decrease in adsorption capacity of Centaur carbon, however, was greater than the other two carbons. The carbon adsorption capacity for COS decreased in proportion to the percentage of H2S in the gas stream. More adsorption sites appear to be available to H2S, a smaller molecule. Ammonia, which has been found to increase H2S adsorption capacity, did not increase the capacity for COS.     

Application of biofiltration system on AOC removal: column and field studies

The Cheng-Ching Lake Water Treatment Plant (CCLWTP) is the main supplier of domestic water for the Greater Kaohsiung area, the second largest metropolis in Taiwan. Biological activated carbon (BAC) filtration is one of the major treatment processes in CCLWTP. The objectives of this study were to evaluate the effectiveness of BAC filtration on water treatment in the studied advanced water treatment plant and its capability on pollutants [e.g., AOC (assimilable organic carbon), bromide, bromate, iron] removal. In this study, water samples from each treatment process of CCLWTP were collected and analyzed periodically to assess the variations in concentrations of AOC and other water quality indicators after each treatment unit. Moreover, the efficiency of biofiltration process using granular activated carbon (GAC) and anthracite as the fillers was also evaluated through a column experiment. Results show that the removal efficiencies for AOC, bromide, bromate, and iron are 86% 100%, 17%, and 30% after the BAC filter bed, respectively. This indicates that BAC filtration plays an important role in pollutant removal. Results also show that AOC concentrations in raw water and effluent of the CCLWTP are approximately 143 and 16 microg acetate-Cl(-1), respectively. This reveals that the treatment processes applied in CCLWTP is able to remove AOC effectively. Results of column study show that the AOC removal efficiencies in the GAC and anthracite columns are 60% and 17%, respectively. Microbial colonization on GAC and anthracite were detected via the observation of scanning electron microscopic images. The observed microorganisms included bacteria (rods, cocci, and filamentous bacteria), fungi, and protozoa. Results from this study provide us insight into the mechanisms of AOC removal by advanced water treatment processes. These findings would be helpful in designing a modified water treatment system for AOC removal and water quality improvement.     

酸碱溶液改性竹基活性炭生物降解H2S

对竹基活性炭采用酸、碱溶液浸渍的方法改性,并用化学和表面形态分析等表征方法测试了其改性前后的特性,研究了不同溶液对改性竹基活性炭在微生物挂膜和滴滤塔去除H2S方面的影响。研究结果表明,用10％NaOH溶液改性后的竹基活性炭较未改性的竹基活性炭碱性基团含量增加了0．614mmol／L,平衡含水率增加了6．08％,碘吸附值增加了29．6mL／g,这些物化性能的改变更有利于生物竹基活性炭去除H2S。对比5种改性方法对生物降解H2S性能的影响,在H2S人口浓度为150～4500mg／m^3、循环液喷淋量0．2L／h、pH6．5—7．5、气体停留时间66s的条件下,经NaOH溶液改性后的竹基活性炭,对H2S的去除率达93．4％以上,效果好于其他改性方法的竹基活性炭。     

Kinetic evaluation of H2S and NH3 biofiltration for two media used for wastewater lift station emissions

In this study, biofiltration using a natural wood chip medium and a commercial biofiltration medium was evaluated for the removal of moderate concentrations of hydrogen sulfide (H2S) (up to 100 parts per million by volume [ppmv]) in the presence of significant concentrations of ammonia (NH3). These levels were chosen as representative of wastewater lift station emissions in the Brownsville, TX, area. NH3-removing portions of the biofilms may compete with H2S-removing portions and inhibit H2S removal. H2S process removal efficiencies for the commercial and natural media ranged from 90 to 96% depending on inlet loading and media type and bed height. Kinetic analysis of the H2S removal process followed apparent first-order reaction behavior. The average first-order reaction rates were 0.03 sec(-1) for the commercial medium and 0.09 sec(-1) for the natural medium. Pressure drops across the columns ranged from 0.41 in. H2O/ft for the commercial medium to 1.41 in. H2O/ft for the natural medium. NH3 gas levels of up to 80 ppmv did not affect the H2S removal process efficiency, and calculated kinetic rate constants for H2S removal remained almost the same. The NH3 gas also was removed simultaneously with the H2S up to 98% removal efficiency by the commercial medium.     

Effect of adsorbents coated with titanium dioxide on the photocatalytic degradation of propoxur

Photocatalytic oxidation of pesticides in aqueous media irradiated by UV light is a rapidly growing field of research. Therefore, the treatment technology for degradation of propoxur (an insecticide) using titanium dioxide coated on the supports such as activated carbon, zeolite, brick, quartz and glass beads, was performed in this research. Results show that GAC/TiO2 is the best complexing agent for oxidizing propoxur because of its adsorption properities. The others follow the sequence: plain TiO2 > glass beads > zeolite > brick > quartz. The degradation rate of propoxur with plain TiO2 is higher than that with TiO2/GAC complexing agent. But the mineralization rate of propoxur with plain TiO2 is lower than that with TiO2/GAC complexing agent. However, it can be concluded that using GAC as the support can improve the photocatalytic efficiency.     

Fenton组合工艺处理焦化厂生化出水的应用研究

比较了Fenton氧化、Fenton氧化+活性炭及Fenton氧化+生物活性炭工艺对焦化厂生化出水的处理效果.结果表明,Fe2+、H2O2的投加量分别为56、27.2 mg/L时,Fenton氧化工艺对水样的UV254、颜色度(VIS380)、COD和总氰均有较好的去除效果;Fenton氧化+活性炭工艺在有效去除UV254、VIS380、COD和总氰的同时,能强化活性炭的吸附效果,并能显著提高水样的生化性能;Fenton氧化+生物活性炭工艺能有效去除UVM254,VIS380、COD与总氰,使出水达到<污水综合排放标准>(GB 8978-1996)一级标准.     

Long-term operation of a biofilter for simultaneous removal of H2S and NH3

Simultaneous removal of NH3 and H2S was investigated using two types of biofilters--one packed with wood chips and the other with granular activated carbon (GAC). Experimental tests and measurements included analyses of removal efficiency (RE), metabolic products, and results of long-term operation (around 240 days). The REs for NH3 and H2S were 92 and 99.9%, respectively, before deactivation. After deactivation, the RE for NH3 and H2S were decreased to 30-50% and 75%, respectively. The activity of nitrifying bacteria was inhibited by high concentrations of H2S (over 200 ppm) but recovered gradually after H2S addition was ceased. However, the Thiobacillus thioparus as sulfur oxidizing bacteria did not show inhibition at the NH3 concentration under 150-ppm conditions. The deactivation of the biofilter was caused by metabolic products [elemental sulfur and (NH4)2SO4] accumulating on the packing materials during the extended operation. The removal capacities for NH3 and H2S were 6.0-8.0 and 45-75 mg N, S/L/hr, respectively.     

A hybrid biological process of indoor air treatment for toluene removal

Bioprocesses, such as biofiltration, are commonly used to treat industrial effluents containing volatile organic compounds (VOCs) at low concentrations. Nevertheless, the use of biofiltration for indoor air pollution (IAP) treatment requires adjustments depending on specific indoor environments. Therefore, this study focuses on the convenience of a hybrid biological process for IAP treatment. A biofiltration reactor using a green waste compost was combined with an adsorption column filled with activated carbon (AC). This system treated a toluene-micropolluted effluent (concentration between 17 and 52 µg/m³), exhibiting concentration peaks close to 733 µg/m³ for a few hours per day. High removal efficiency was obtained despite changes in toluene inlet load (from 4.2 × 10^?3 to 0.20 g/m³/hr), which proves the hybrid system’s effectiveness. In fact, during unexpected concentration changes, the efficiency of the biofilter is greatly decreased, but the adsorption column maintains the high efficiency of the entire process (removal efficiency [RE] close to 100%). Moreover, the adsorption column after biofiltration is able to deal with the problem of the emission of particles and/or microorganisms from the biofilter.

ImplicationsIndoor air pollution is nowadays recognized as a major environmental and health issue. This original study investigates the performance of a hybrid biological process combining a biofilter and an adsorption column for removal of indoor VOCs, specifically toluene.     

活性炭纤维对水中微囊藻毒素的吸附性能

利用活性炭纤维对水中微囊藻毒素MC—LR的吸附,研究了吸附过程的热力学与动力学特性。结果表明,活性炭纤维对MC—LR的平衡吸附量在相同温度下随MC-LR初始浓度的增加而显著增大,并随着温度升高而增加,最大吸附量达246μg／g。不同温度条件下,活性炭纤维对MC-LR的吸附均较好地符合Langmuir等温吸附模型。通过热力学分析发现,△H=15．7kJ／mol、△G〈0、△S〉0,表明该吸附是自发的、吸热的过程,温度升高有利于吸附反应。动力学研究表明,该过程符合一级动力学方程。吸附反应速率受颗粒内扩散和液膜扩散共同影响。活性炭纤维经再生后,平衡吸附量变化较小,具有良好的重复使用性能。     

季铵化合物对好氧活性污泥吸附Ni2+的影响研究

以季铵化合物中最具潜在影响力、毒性较大的苄基季铵盐(BAC)为模型物,进行了BAC对好氧活性污泥吸附Ni2+的影响研究.结果表明,当反应液初始pH≤3时,不同浓度的BAC对好氧活性污泥吸附Ni2+的影响较小,当初始pH在3～9时,不同浓度的BAC对Ni2+吸附的抑制影响顺序为100 mg/L＞20 mg/L＞0 mg/...     

Packing material formulation for odorous emission biofiltration

In biological gas treatment, like biofiltration of volatile organic compounds or odorous substances, the microbial nutritional needs could be a key factor of the process. The aim of this work is to propose a new packing material able to provide the lacking nutrients. In the first part of this study, two kinds of material composed of calcium carbonate, an organic binder and two different nitrogen sources, ammonium phosphate and urea phosphate (UP), were compared. The new supports present bulk densities between 0.88 and 1.15g cm(-3), moisture retention capacities close to 50% and 70%, and water cohesion capacities greater than six months for the material with 20% binder. In the second part, oxygen consumption measurements in liquid experiments show that these packing materials could enhance bacterial growth compared to pine bark or pozzolan and have no inhibitory effect. The biodegradation of different substrates (sodium sulfide and ammonia) and the support colonization by the biomass were evaluated. Finally, UP 20 was chosen and tested in a hydrogen sulfide or ammoniac biofiltration process. This showed that, for H2S concentrations greater than 100mg m(-3), UP 20 has a real advantage over pine bark or pozzolan.     

Effect of operational factors on bioregeneration of binary phenol and 4-chlorophenol-loaded granular activated carbon using PVA-immobilized biomass cryogels

The effects of dry biomass density in cryogel beads, shaking speed and initial concentration ratio of phenol to 4-chlorophenol (4-CP) on the bioregeneration efficiencies of binary phenol and 4-CP-loaded granular activated carbon (GAC) for phenol and 4-CP, respectively, were investigated under the simultaneous adsorption and biodegradation approach. The results revealed higher bioregeneration efficiencies of binary-loaded GAC for phenol and 4-CP at higher dry biomass density but moderate shaking speed. The optimum dry biomass density in cryogel beads and shaking speed for use in bioregeneration were found to be 0.01 g/mL and 250 rpm, respectively. With respect to the initial phenol to 4-CP concentration ratio, the bioregeneration efficiencies were lower under increasing phenol and 4-CP initial concentrations, respectively, with the effect being more conspicuous under increasing 4-CP concentration. Higher bioregeneration efficiencies were achieved with the use of immobilized rather than suspended biomasses.     

Biomass-derived materials in the remediation of heavy-metal contaminated water: removal of Cadmium(II) and copper(II) from aqueous solutions

Manganese-coated activated carbon (MCAC) and activated carbon were used in batch experiments for the removal of cadmium(II) and copper(II). Results showed that uptake of Cd(II) and Cu(II) was unaffected by increases in pH (3.0 to 8.5) or concentration (1 to 20 mg/L). Increased ionic strength (from 0.001 to 1 M NaNO3), however, significantly affected the uptake of Cd(II); adsorption of Cu(II) was not affected. Freundlich adsorption isotherm results indicated that MCAC possessed higher sorption capacity than activated carbon. Second-order rate constants were found to be 0.0386 for activated carbon and 0.0633 g/mg x min for MCAC for Cd(II) and 0.0774 for AC and 0.1223 g/mg x min for MCAC for Cu(II). Column experiments showed that maximum sorption capacity of MCAC was 39.48 mg/g for Cu(II) and 12.21 mg/g for Cd(II).     

Hydrogen sulfide generation in simulated construction and demolition debris landfills: impact of waste composition

Hydrogen sulfide (H2S) generation in construction and demolition (C&D) debris landfills has been associated with the biodegradation of gypsum drywall. Laboratory research was conducted to observe H2S generation when drywall was codisposed with different C&D debris constituents. Two experiments were conducted using simulated landfill columns. Experiment 1 consisted of various combinations of drywall, wood, and concrete to determine the impact of different waste constituents and combinations on H2S generation. Experiment 2 was designed to examine the effect of concrete on H2S generation and migration. The results indicate that decaying drywall, even alone, leached enough sulfate ions and organic matter for sulfate-reducing bacteria (SRB) to generate large H2S concentrations as high as 63,000 ppmv. The codisposed wastes show some effect on H2S generation. At the end of experiment 1, the wood/drywall and drywall alone columns possessed H2S concentrations > 40,000 ppmv. Conversely, H2S concentrations were < 1 ppmv in those columns containing concrete. Concrete plays a role in decreasing H2S by increasing pH out of the range for SRB growth and by reacting with H2S. This study also showed that wood lowered H2S concentrations initially by decreasing leachate pH values. Based on the results, two possible control mechanisms to mitigate H2S generation in C&D debris landfills are suggested.     

Backfitting Electrostatic Precipitators: Gas Velocity and Reliability Considerations

Abstract

The kinetic behavior of the toluene biofiltration process was investigated in this research. Toluene was used as a model compound for less water-soluble gas pollutants. The limiting factor in the overall toluene biofiltration process was determined by analyzing the effectiveness factor of the biofilm along the biofilter. Experiments were conducted in three laboratory-scale biofilters packed with mixtures of chaff/compost, D.E. (diatomaceous earth)/compost and GAC (granular activated carbon)/compost, respectively. A mathematical model previously proposed was verified in this study as being applicable to these biofilters packed with different filter materials. Both the experimental and theoretical results confirmed that the biodegradation rate along the biofilter followed the zero order, fractional order to first order kinetics as toluene concentration decreased. Moreover, at higher toluene concentration, biodegradation rate and mass flux of toluene were lower near the bottom of the biofilter due to substrate inhibition. Analysis of the effectiveness factor indicated that biofiltration of a less soluble compound such as toluene should not be operated at high gas flow rates (low gas residence times) due to the mass transfer limitation of such a system. At an approximate constant inlet toluene concentration of 0.9 g/m³, the toluene removal efficiency in these three biofilters would drop below 90% when the gas residence time decreased to 2.5, 2.5, and 2.0 min, respectively.     

活性炭吸附硫化氢及微波辐照解吸研究

研究了两种活性炭对硫化氢的平衡吸附性能力,并对活性炭床层的穿透性进行了考察;吸附饱和和活性炭在微波辐射的作用下进行解吸。实验表明,解吸效率与微波作用时间及温度有关,在本实验条件下H2S解吸效率达90．1％。     

用于污水再生利用的生物活性炭床的有机物降解特性

以微生物增殖动力学的基本方程-莫诺方程为出发点,通过氮同位素分析比较了具有同源性微生物的生物陶粒滤床和生物活性炭床的有机物生物降解规律,建立了生物活性炭床的有机物生物降解动力学方程,提出在污水再生利用过程中生物活性炭床符合高基质有机物降解动力学模型,即有机物降解呈一级反应动力学方程。以此方程为基础,分析计算了生物活性炭床沿炭床深度的吸附性能,结果表明,在生物活性炭床中,随生物功能的减弱,生物活性炭床对有机物的吸附能力逐渐加强。     

海藻酸钠-刺槐豆胶复合凝胶珠吸附孔雀绿简

以刺槐豆胶、海藻酸钠为材料制备复合凝胶珠,利用红外光谱、热重分析对其进行表征,探讨孔雀绿浓度、吸附时间及pH对复合凝胶珠吸附孔雀绿的影响。红外光谱和热重分析表明,复合凝胶珠制备成功且热稳定性介于刺槐豆胶和海藻酸钠之间。复合凝胶珠对孔雀绿的吸附在5 h后达到平衡,pH=6为最佳吸附pH,相同条件下复合凝胶珠对孔雀绿的吸附作用优于活性炭,其对孔雀绿的吸附行为符合Freundlich吸附等温方程和颗粒内扩散模型。海藻酸钠-刺槐豆胶复合凝胶珠有望成为新的处理印染废水的吸附剂。     

沼液中臭味物质的去除方法及其对营养物质的影响

采用臭氧曝气法、粉末活性炭吸附法、颗粒活性炭过滤法、臭氧曝气-粉末活性炭吸附联用法、空气曝气-粉末活性炭吸附联用法对沼液中的氨气、硫化氢、吲哚、挥发酚类等主要致嗅物质的去除情况进行了研究,同时分析了不同方法对沼液中营养物质TN、DN、TP、DP等的影响。结果表明,采用粉末活性炭吸附法处理沼液,臭味物质的去除情况以及营养物质的保留效果最好,当粉末活性炭投加量为15 000 mg/L时,沼液中的硫化氢、吲哚、挥发酚已经完全去除,氨氮、氨气的去除率分别为11.42%、13.98%;DN、DP含量分别减少了10.46%、19.53%,但是TN、TP含量分别增加了6.26%、9.63%。