Kinetic study of the anaerobic biodegradation of alkyl polyglucosides and the influence of their structural parameters

This paper reports a study of the anaerobic biodegradation of non-ionic surfactants alkyl polyglucosides applying the method by measurement of the biogas production in digested sludge. Three alkyl polyglucosides with different length alkyl chain and degree of polymerization of the glucose units were tested. The influence of their structural parameters was evaluated, and the characteristics parameters of the anaerobic biodegradation were determined. Results show that alkyl polyglucosides, at the standard initial concentration of 100 mgC L^?1, are not completely biodegradable in anaerobic conditions because they inhibit the biogas production. The alkyl polyglucoside having the shortest alkyl chain showed the fastest biodegradability and reached the higher percentage of final mineralization. The anaerobic process was well adjusted to a pseudo first-order equation using the carbon produced as gas during the test; also, kinetics parameters and a global rate constant for all the involved metabolic process were determined. This modeling is helpful to evaluate the biodegradation or the persistence of alkyl polyglucosides under anaerobic conditions in the environment and in the wastewater treatment.     

Effect of the alkyl chain length on the anaerobic biodegradability and toxicity of quaternary ammonium based surfactants

The anaerobic biodegradability and toxicity to methanogenic gas production of different alkyl chain length homologs of quaternary ammonium based surfactants were examinated. Two series of these cationic surfactants were selected: alkyl trimethyl ammonium and alkyl benzyl dimethyl ammonium compounds. A simple anaerobic gas production test containing municipal digester solids as a source of anaerobic bacteria was used. Under the applied methanogenic conditions, the cationic surfactants tested showed a very poor primary biodegradation and no evidence of any extent of ultimate biodegradation was observed. The toxicity of quaternary ammonium based surfactants to methanogenic gas production decreased with increasing the alkyl chain length.     

Anaerobic digestion of linear alkyl benzene sulfonates: biodegradation kinetics and metabolite analysis

In the present work the effect of the alkyl chain length and the position of the sulfophenyl substituent of the linear alkylbenzene sulfonates (LAS) on their anaerobic biodegradability have been investigated. Degradation kinetics of the linear alkyl benzene sulfonates homologues, 2C₁₀LAS, 2C₁₂LAS and 2C₁₄LAS, have been studied. It has been also investigated the effect of the isomer type on the degradation rate of the LAS molecule through the comparative study of the 2C₁₀LAS and 5C₁₀LAS isomers. Batch anaerobic biodegradation tests were performed using sludge from the anaerobic digester of a wastewater treatment plant as microorganisms source. Ultimate biodegradation was evaluated from the biogas production whereas primary biodegradation was determined by specific analysis of the surfactant. LAS homologues and isomers showed a negligible primary biodegradation under anaerobic conditions. Furthermore, analysis of sulfophenyl carboxilates (SPC) by LC–MS indicated a low and constant level of these LAS degradation metabolites over the test period. These data are consistent with a minimal transformation of the LAS parent molecule in the anaerobic digesters. On the other hand, the addition of the shortest alkyl chain length homologues, decyl and dodecylbenzene sulfonates, reduces the biogas production whereas the most hydrophobic homologue, the tetradecylbenzene sulfonate, enhances the biogas production. This LAS homologue seems to increase the availability of organic compounds sorbed on the anaerobic sludge promoting their biodegradation.     

Biodegradation of mono-alkyl phthalate esters in natural sediments

Mono-alkyl phthalate esters (MPEs) are primary metabolites of di-alkyl phthalate esters (DPEs), a family of industrial chemicals widely used in the production of soft polyvinyl chloride and a large range of other products. To better understand the long term fate of DPEs in the environment, we measured the biodegradation kinetics of eight MPEs (-ethyl, -n-butyl, -benzyl, -i-hexyl, -2-ethyl-hexyl, -n-octyl, -i-nonyl, and -i-decyl monoesters) in marine and freshwater sediments collected from three locations in the Greater Vancouver area. After a lag period in which no apparent biodegradation occurred, all MPEs tested showed degradation rates in both marine and freshwater sediments at 22 °C with half-lives ranging between 16 and 39 h. Half-lives increased approximately 8-fold in incubations performed at 5 °C. Biodegradation rates did not differ between marine and freshwater sediments. Half-lives did not show a relationship with increasing alkyl chain length. We conclude that MPEs can be quickly degraded in natural sediments and that the similarity in MPE degradation kinetics among sediment types suggests a wide occurrence of nonspecific esterases in microorganisms from various locations, as has been reported previously.     

Application of a computational model for Michael addition reactivity in the prediction of toxicity to Tetrahymena pyriformis

A computational model to predict acute aquatic toxicity to the ciliate Tetrahymena pyriformis has been developed. A general prediction of toxicity can be based on three consecutive steps: 1. Identification of a potential reactive mechanism via structural alerts; 2. Confirmation and quantification of (bio)chemical reactivity; 3. Establishing a relationship between calculated reactivity and toxicity. The method described herein uses a combination of a reactive toxicity (RT) model, including computed kinetic rate constants for adduct formation (log k) via a Michael acceptor mechanism of action, and baseline toxicity (BT), modelled by hydrophobicity (octanol-water partition coefficient). The maximum of the RT and BT values defines acute toxicity for a particular compound. The reactive toxicity model is based on site-specific steric and quantum chemical ground state electronic properties. The performance of the model was examined in terms of predicting the toxicity of 106 potential Michael acceptor compounds covering several classes of compounds (aldehydes, ketones, esters, heterocycles). The advantages of the computational method are described. The method allows for a closer and more transparent mechanistic insight into the molecular initiating events of toxicological endpoints.     

Fate and effect of monoalkyl quaternary ammonium surfactants in the aquatic environment

The effect of the alkyl chain of quaternary ammonium-based surfactants on their aquatic toxicity and aerobic biodegradability has been studied. Two families of monoalkylquats surfactants were selected: alkyl trimethyl ammonium and alkyl benzyl dimethyl ammonium halides. Acute toxicity tests on Daphnia magna and Photobacterium phosphoreum were carried out and EC50 values in the range of 0.1-1 mg/l were obtained for the two series of cationic surfactants. Although the substitution of a benzyl group for a methyl group increases the toxicity, an incremental difference in toxicity between homologs of different chain length were not observed. Biodegradability of the different homologs was determined not only in standard conditions but also in coastal water, both tests yielding similar results. An increase in the alkyl chain length or the substitution of a benzyl group for a methyl group reduces the biodegradation rate. The degradation of these compounds in coastal waters was associated with an increase in bacterioplankton density, suggesting that the degradation takes place because the compound is used as a growth substrate.     

Measurement of octanol–air partition coefficients using solid-phase microextraction (SPME)—application to hydroxy alkyl nitrates

Multifunctional organic compounds are thought to constitute a major component of the organic matter found in atmospheric particles. Their partitioning into the organic matter depends on their structure, their chemical properties and the properties of the absorbing matrix. It was recently shown that octanol is a suitable surrogate for organic particles and the octanol–air partition coefficient (K_OA) was suggested as a useful tool for estimating the partitioning of organic compounds into atmospheric particles that contain high organic mass fractions. In this paper, we present a new and simple technique for the determination of K_OA using solid phase microextraction (SPME) relative to a known Henry's law constant. We apply the technique for the determination of K_OA of β-, γ- and δ-C₃–C₅ hydroxy alkyl nitrates. The temperature dependence of K_OA for some of the compounds is also measured. It is shown that the solubility constants of these compounds are higher in octanol than in water and that the solubility in octanol increases with the length of the hydrophobic chain and with increasing distance between the hydroxy and the nitrooxy groups. Partition coefficients between the gas and particulate phase (K_p) are calculated using the determined K_OA values and their atmospheric implications are discussed.     

Fate and transport of monoterpenes through soils. Part I. Prediction of temperature dependent soil fate model input-parameters

Monoterpenes are C10H(n)O(n') compounds of natural origin and are potentially environmentally safe substitutes for traditional pesticides. Still, an assessment of their environmental behaviour is required. As a first step in a theoretical study focussing on monoterpenes applied as pesticides to terrestrial environments, soil fate model input-parameters were determined for 20 monoterpenes with widely different structural characteristics. Input-parameters are the water solubility (S(W)), vapour pressure (P), n-octanol-water partition coefficient (K(OW)), atmospheric air and bulk water diffusion coefficients (D(A)air and D(W)water), first order biodegradation rate constants (k), and their temperature dependence. Values for these parameters were estimated or taken from previous experimental work. The quality of the estimations was discussed by focussing on their statistics and by comparison with available experimental data. From these properties, the air-water partition coefficient (K(AW), Henry's Law constant), the interface-water partition coefficient (K(IW)) and the organic matter-water partition coefficient (K(OM)) could be estimated with varying levels of accuracy. In general, little experimental data turned out to be available on biodegradation rate constants and on the temperature dependence of physico-chemical parameters.     

Estimating biotransformation rate constants of organic chemicals from modeled and measured elimination rates.

In this study, biotransformation rate constants are estimated for a large set of organic compounds. Biotransformation (km) is considered part of the total elimination, further consisting of physico-chemical elimination to water (kw), depuration by feces (kf) and growth dilution (gamma). Existing models are used to estimate kw and kf, and gamma. The difference between measured elimination rate constants and the sum of predicted elimination rate constants for water, feces and growth indicates the ration of biotransformation in the total elimination. In all examined animal classes, polycyclic aromatic hydrocarbons seem to be metabolized at an intermediate rate. Because of the relative low hydrophobicity of some of the studied compounds, their physico-chemical elimination rate constant is relatively high, and the relative contribution of metabolism to total elimination of these compounds is therefore relatively low. Fish seem to be capable of metabolizing chlorodibenzo-p-dioxins and -furans, DDT, chloroanilines and phenol.     

Degradation of octylphenol and nonylphenol by ozone - part I: direct reaction

This aqueous reaction between ozone and two alkylphenols (APs), namely octylphenol (OP) and nonylphenol (NP), has been investigated. Both compounds are important endocrine disrupting chemicals, which arise from the biodegradation of alkylphenol ethoxylates and are often found at relatively high concentrations in wastewater effluents. In this paper the results of an experimental study are presented which provide values for the reaction rate constants between molecular ozone and undissociated OP and NP, and overall reaction rate constants for the degradation of the two APs at pH values in the range of 7-9. The kinetic rate constants for OP and NP degradation by molecular ozone were 4.33(+/-0.18) x 10(4) and 3.90(+/-0.10) x 10(4) M(-1) s(-1), and the reaction stoichiometry was similar in both cases and equal to approximately 1.3:1 ([O3]:[AP]). The overall second order reaction rate constants for the two APs increased significantly with increasing pH, which is believed to be mainly due to the increasing influence of indirect radical reaction with increasing pH; this aspect is considered in more detail in a companion paper. A preliminary investigation of the reaction mechanism suggests that an initial product of ozonation is hydroxyl-alkyl phenol.     

Accumulation and elimination kinetics of di-, tri- and tetra chlorobiphenyls by goldfish after dietary and aqueous exposure

Bioaccumulation kinetics of five di-, tri- and tetrachlorobiphenyls from water and food were studied in laboratory experiments with goldfish (Carassius auratus). First order rate constants for uptake from water and clearance were determined after simultaneous administration of the five compounds in constant concentration, and were related to bioconcentration factors obtained in a static fish-water equilibration system. Biomagnification by retention of the PCB's from food was studied in a separate experiment.The difference in clearance rates for the chlorobiphenyls is the main reason for the different bioconcentration and biomagnification factors.Absorption efficiencies from water and food are higher than 40%. Clearance half lives vary from 10 days for 2,5-dichlorobiphenyl to 60 days for 2,3′,4′5-tetrachlorobiphenyl, which is correlalated with the decreasing aqueous solubilities of the compounds. Bioconcentration factors are between 0.4 × 10⁶ and 1.5 × 10⁶, biomagnification factors between 0.2 and 1.7, based on extractable lipids. Substitution of chlorine in the position para to the phenyl-phenyl bond influences hydrophobicity and bioaccumulation of the PCB's more strongly than substitution in ortho position.A kinetic model is developed which accounts for the influence of the lipid content of the fish on the clearance rate of a chemical. Reproducible determination of the bioconcentration potential of environmental chemicals is possible by use of an “internal bioaccumulation standard” in a kinetic test system. Food chain accumulation in fish is likely to be an important process only for persistent chemicals with extremely low water solubility.     

Structure-activity relationships for association of linear alkylbenzene sulfonates with activated sludge

Sorption of linear alkylbenzene sulfonates (LAS) on sludge particles from wastewater treatment plants was studied. The effect of alkyl chain length and the water hardness were investigated. Sorption on sludge increases with increasing alkyl chain length in the LAS molecules. The results are interpreted in terms of a hydrophobic bonding mechanism being the critical micelle concentration a good index of the surfactant hydrophobicity. The increase in free energy of adsorption for the addition of successive methylene groups to the alkyl chain was estimated as 2.4 kJ/mol. Water hardness clearly enhances the sorption of LAS homologues on sludge and seems to promote cooperative sorption at high surfactant and calcium ion concentrations. An empirical equation was provided that allow to estimate the partition coefficient between aqueous and solid phases for LAS homologues as a function of the alkyl chain length and the water hardness.     

Designing green plasticizers: influence of molecular geometry on biodegradation and plasticization properties

The plasticizer di (2-ethylhexyl) phthalate (DEHP) and its metabolites are considered ubiquitous contaminants, which have a range of implications on the environment and human health. This work considered several alternative compounds with structural features similar to DEHP. This added to the understanding of why DEHP is so poorly biodegraded once it enters the environment. These alternative compounds were based on 2-ethylhexyl diesters of maleic acid (cis-isomer), fumaric acid (trans-isomer) and succinic acid (saturated analogue). The rates of biodegradation by the common soil bacterium Rhodococcus rhodocrous were shown to be dependent on the structure of the central unit derived from the diacid used to make the ester. The diacid components of DEHP and the maleate both had a cis orientation and they were the two that were slow to biodegrade. Plasticizing properties were also compared and, because the ester of the saturated succinic acid was degraded quickly and also had good plasticizing properties, it was concluded that the succinic esters of straight chain alcohols would make the best green plasticizers. The maleate ester had excellent plasticizing properties but this is mitigated by a significant resistance to biodegradation.     

Comparison of the effects of variable site temperatures and constant incubation temperatures on the biodegradation of petroleum hydrocarbons in pilot-scale experiments with field-aged contaminated soils from a cold regions site

Temporal atmospheric temperature changes during summers at sub-Arctic sites often cause periodic fluctuations in shallow landfarm and surface soil temperatures. However, little information is available on the effect of site-relevant variations on biodegradation performance in cold climates. This study compares the rate and extents of biodegradation of petroleum hydrocarbons at variable site temperatures (1-10 °C) representative of summers at a sub-Arctic site reported previously with those obtained under a constant average temperature of 6 °C. The biodegradation was evaluated in pilot-scale landfarming experiments with field-aged petroleum-contaminated soils shipped from Resolution Island (61°30′N, 65°00′W), Nunavut, Canada. Under the variable site temperature conditions biodegradation rate constants of semi- (F2) and non-volatile (F3) hydrocarbon fractions were enhanced by over a factor of two during the 60-d experiment, compared to the constant temperature mode. The decrease in total petroleum hydrocarbons (TPH) under the variable site temperature mode was 55% compared to only 19% under the constant average temperature mode. The enhanced biodegradation is attributable to the non-linear acceleration of microbial activity between 4.7 and 10 °C and faster growth of indigenous hydrocarbon-degrading microbial populations. The first-order biodegradation rate constants of 0.018, 0.024 and 0.016 d⁻¹ for TPH, F2 and F3 fractions at the variable site temperature were in agreement with those determined by an on-site experiment at the same site.     

Slow desorption of PCBs and chlorobenzenes from soils and sediments: relations with sorbent and sorbate characteristics

The kinetics of slow desorption were studied for four soils and four sediments with widely varying characteristics [organic carbon (OC) content 0.5-50%, organic matter (OM) aromatic content (7-37%)] for three chlorobenzenes and five polychlorinated biphenyls (PCBs). Slowly and very slowly desorbing fractions ranged from 1 to 50% (slow) and 3 to 40% (very slow) of the total amount sorbed, and were observed for all compounds and all soils and sediments. In spite of the wide variations in sorbate K(OW) (factor 1000) and sorbent characteristics, the rate constants of slow (k(slow), around 10(-3) h(-1)) and very slow (k(very slow), 10(-5)-10(-4) h(-1)) desorption appeared to be rather constant among the sorbates and sorbents (both within a factor of 5). There was a good correlation (r(2) above 0.9) between the distribution over the slow, very slow and rapid sediment fractions and log K(OC), indicating that sorbate hydrophobicity may be important for this distribution. No correlation could be found between sorbent characteristics [OC, N, and O in the organic matter, polarity index C/(N+O), OC aromaticity as determined by CP-MAS (13)C-NMR] and slow desorption parameters (slowly/very slowly desorbing fractions+corresponding rate constants). The absence of (1) a correlation between k(slow) and k(very slow), respectively, and OC content, and (2) the narrow range of k(slow) and k(very slow) values, indicates that intra-OM diffusion is not the mechanism of slow or very slow desorption, because on the basis of this mechanism it would be expected that increasing OC content would lead to longer diffusion pathlengths and, consequently, to smaller rate constants. In addition, it was tested whether differential scanning calorimetry would reveal a glass transition in the soils/sediments. In spite of the sensitivity of the equipment used (changes in heat flow in the micro-Watt range were measurable), a glass transition was not observed. This means that activation enthalpies of slow desorption can be calculated from desorption measurements at various temperatures. In the present study these values ranged from 60 to 100 kJ/mol among the various soils and sediments studied.     

Model coupling intraparticle diffusion/sorption, nonlinear sorption, and biodegradation processes

Diffusion, sorption and biodegradation are key processes impacting the efficiency of natural attenuation. While each process has been studied individually, limited information exists on the kinetic coupling of these processes. In this paper, a model is presented that couples nonlinear and nonequilibrium sorption (intraparticle diffusion) with biodegradation kinetics. Initially, these processes are studied independently (i.e., intraparticle diffusion, nonlinear sorption and biodegradation), with appropriate parameters determined from these independent studies. Then, the coupled processes are studied, with an initial data set used to determine biodegradation constants that were subsequently used to successfully predict the behavior of a second data set. The validated model is then used to conduct a sensitivity analysis, which reveals conditions where biodegradation becomes desorption rate-limited. If the chemical is not pre-equilibrated with the soil prior to the onset of biodegradation, then fast sorption will reduce aqueous concentrations and thus biodegradation rates. Another sensitivity analysis demonstrates the importance of including nonlinear sorption in a coupled diffusion/sorption and biodegradation model. While predictions based on linear sorption isotherms agree well with solution concentrations, for the conditions evaluated this approach overestimates the percentage of contaminant biodegraded by as much as 50%. This research demonstrates that nonlinear sorption should be coupled with diffusion/sorption and biodegradation models in order to accurately predict bioremediation and natural attenuation processes. To our knowledge this study is unique in studying nonlinear sorption coupled with intraparticle diffusion and biodegradation kinetics with natural media.     

A kinetic distribution model of evaporation, biosorption and biodegradation of polychlorinated biphenyls (PCBs) in the suspension of Pseudomonas stutzeri

Kinetics of distribution of PCBs in an active bacterial suspension of Pseudomonas stutzeri was studied by monitoring the evaporated amounts and the concentration remaining in the liquid medium with the biomass. To determine the biodegradation rate constants of the individual congeners of the PCB formulation Delor 103, a model considering biosorption, evaporation, and primary biodegradation constructed previously was used. Rate constants of biodegradation imply that biodegradation of individual congeners is structure-dependent process. Biodegradability decreases with increasing number of chlorine substituents in the molecule, especially if they are in the ortho and para positions. On the other hand, the increasing number of free ortho and meta positions in the biphenyl molecule leads to better biodegradability. For a simple empirical determination of the influence of the chlorine substitution pattern on biodegradability, the di- and trichlorobiphenyl rate constants of biodegradation were analysed.     

Alkylcyclohexanes in Environmental Geochemistry

The n -alkylated cyclohexanes (CHs) are a homologous series of hydrocarbon compounds that are commonly present in crude oil and refinery products such as diesel fuel. These compounds exhibit specific distribution patterns for different fuel types, providing useful fingerprints for characterizing petroleum products, especially after degradation of n -alkanes has occurred. However, there are no published data to show how these compounds are altered in the environment after long-term spillage of petroleum products. This paper presents two case studies of oil spills that demonstrate the changing distribution patterns resulting from long-term anaerobic microbial degradation. These spills are the 1979 crude-oil spill in Bemidji, Minnesota, and a chronic diesel-fuel spillage from 1953–1991 at Mandan, North Dakota. The alkyl CHs in both spilled oil products are affected by similar biodegradative processes in which the compounds undergo a consistent pattern of loss from the high molecular weight end of the homolog distribution. Degradation results in a measurable increase in the concentrations of the homologs in the lower molecular weight range, a gradual lowering in carbon number of the homolog maximum, and a gradual decrease of the total homolog range from the high molecular weight end. This pattern is the opposite of low-end loss expected with weathering and aerobic biodegradation. The enhancement of the low molecular mass alkyl CH homologs, if not recognized as a degradative pathway of diesel fuel in an anaerobic environment, can potentially be misinterpreted in fuel-oil fingerprinting as deriving from lower distillation-range fuels or admixture of diesel with other fuels. Published by Elsevier Science Ltd on behalf of AEHS.     

Influence of microbial and synthetic surfactant on the biodegradation of atrazine

The present study reports the effect of surfactants (rhamnolipids and triton X-100) on biodegradation of atrazine herbicide by strain A6, belonging to the genus Acinetobacter. The strain A6 was able to degrade nearly 80 % of the 250-ppm atrazine after 6 days of growth. The bacterium degraded atrazine by de-alkylation process. Bacterial cell surface hydrophobicity as well as atrazine solubility increased in the presence of surfactant. However, addition of surfactant to the mineral salt media reduced the rate and extent of atrazine degradation by decreasing the bioavailability of herbicide. On the contrary, addition of surfactant to atrazine-contaminated soil increased the rate and extent of biodegradation by increasing the bioavailability of herbicide. As compared to triton X-100, rhamnolipids were more efficient in enhancing microbial degradation of atrazine as a significant amount of atrazine was removed from the soil by rhamnolipids. Surfactants added for the purpose of hastening microbial degradation may have an unintended inhibitory effect on herbicide degradation depending upon contiguous condition, thus highlighting the fact that surfactant must be judiciously used in bioremediation of herbicides.     

Biodegradation rates of 2-methylisoborneol (MIB) and geosmin through sand filters and in bioreactors

Taste and odour (T&O) causing compounds, in particular, 2-methylisoborneol (MIB) and geosmin, are a problem for water authorities as they are recalcitrant to conventional water treatment. In this study, biological sand filtration was shown to be an effective process for the complete removal of MIB and geosmin, with removal shown to be predominantly through biodegradation. In addition, MIB and geosmin were also effectively degraded in batch bioreactor experiments using biofilm sourced from one of the sand filters as the microbial inoculum. The biodegradation of MIB and geosmin was determined to be a pseudo-first-order reaction with rate constants ranging between 0.10 and 0.58 d⁻¹ in the bioreactor experiments. Rate constants were shown to be dependent upon the initial concentration of the microbial inoculum but not the initial concentration of MIB and geosmin when target concentrations of 200 and 50 ng l⁻¹ were used. Furthermore, rate constants were shown to increase upon re-exposure of the biofilm to both T&O compounds. Enrichment cultures with subsequent community profile analysis using 16S rRNA-directed PCR-DGGE identified four bacteria most likely involved in the biodegradation of geosmin within the sand filters and bioreactors. These included a Pseudomonas sp., Alphaproteobacterium, Sphingomonas sp. and an Acidobacteriaceae member.