Validation studies of an automated preconcentration water sampler (APS) for chlorinated dibenzo-p-dioxins and dibenzofurans

An Automated Preconcentration Sampler (APS) was developed by the Ontario Ministry of the Environment (MOE) and Carleton University for the determination of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in drinking water. The APS employs a two-stage particulate filtration system followed by an XAD-2 resin column. Field and laboratory testing of the APS is required to validate the device before it is put into regular service.The capacity of the APS filtration system is 30 L for a 4 Formazin Turbidity Unit (FTU) input water turbidity and greater than 50 L for a typical treated water. Flushing of a clean XAD-2 resin column with 200 L of spiked water showed that the optimum flowrate in terms of spike breakthrough is equal to three times the resin bed volume per minute. This flowrate is used for APS operation. Testing also showed that no spike breakthrough occurred after 200 L of clean water was flushed through a spiked XAD-2 resin column at flowrates in excess of the APS operating flowrate. Spike testing was also carried out on the filters and results are pending. An analytical comparison between the present MOE sampling and analytical procedure and the proposed APS sampling and analytical procedure using a PCDD/PCDF source water is planned.     

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans from catalytic and thermal oxidizers burning dilute chlorinated vapors

Emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (dioxins) have been found from 57 field tests on the oxidation of low (a few to a few hundred) parts per million levels of chlorinated and non-chlorinated volatile organic compounds (VOCs). The oxidation occurs in catalytic oxidizers with platinum, platinum/palladium or chromium(IV) oxide combustion catalysts, or in thermal oxidizers (without a catalyst). The catalyst inlet temperatures ranged from 293 to 573 degrees C. The thermal oxidizer operating temperatures (post-flame) were from 773 to 927 degrees C. Data of the toxic dioxin and furan isomers are reported and also weighted and expressed as international toxic equivalents (TEQ) of 2,3,7,8-tetrachlorodibenzo-p-dioxin. The maximum stack emissions, 1.07 ng/m3 TEQ, occurred at 293 degrees C. Salient results of this field study are: (1) TEQ levels in the stack exponentially increase with a decrease in operating temperature, an empirical equation is TEQ (ng/dscm)=8.4 exp(-0.0084T degrees C); (2) dioxin/furan production occurs at the combustion catalyst; (3) small variations in temperature cause large changes in the congener distribution of the dioxin and furan isomers; (4) molar TEQ yields from the parent compounds fed to the oxidizers are very small (10(-9)-10(-13)); (5) catalytic and thermal oxidizers may destroy dioxins fed from the ambient air; and (6) the oxidation of chlorinated VOCs with non-chlorinated VOCs reduces emissions of dioxins, likely due to the consumption of Cl in producing HCl. Laboratory investigations are needed to understand how dioxins are formed (and emitted) under conditions of this study.     

Exposure of arc-furnace-plant workers to polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs)

This study aimed to evaluate serum polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) levels in electric-arc-furnace workers according to their corresponding occupational exposure. In addition, the ambient PCDD/Fs of the work environment were measured to provide additional support for the exposure and accumulation inside the electric arc furnace. The ambient PCDD/F concentrations inside the electric arc furnace were 1.557-1.917 pg-TEQ/Nm(3), 5-24 folds higher than those outside (0.080-0.385 pg-TEQ/N m(3)). In addition, higher average serum levels were measured in the workers with high occupational dioxin exposure (24.0 pg WHO-TEQ/g lipid) than in those with lower occupational dioxin exposure (13.8 pg WHO-TEQ/g lipid). Higher PCDFs/PCDDs ratios were found in serum samples from high-exposure groups than in low-exposure groups. The higher ratio of PCDFs/PCDDs was also found in ambient samples consistent with other metallurgical processes reported previously. Our results suggest that PCDD/Fs exposure exits in the smelting process of electric arc furnace, and the occupational hygiene should be taken more seriously concern in that workplace.     

溴代二噁英类化合物的环境研究进展

溴代二噁英类化合物是一类剧毒环境污染物,主要来源于溴系阻燃剂与含溴系阻燃剂聚合物的生产、使用和回收等过程.随着溴系阻燃剂的广泛使用,溴代二噁英类化合物的环境和健康风险日益增加,对其环境问题的研究已成为当今环境科学的一大热点,而中国在此方面的研究还相当薄弱.介绍了溴代二噁英类化合物的结构性质,综述了溴代二噁英类化合物的分析方法、污染来源和环境分布,重点探讨了溴代二噁英类化合物的生成机制,介绍了生成溴代二噁英类化合物的影响因素,讨论并总结了当前研究中溴代二噁英类化合物污染来源解析与生成机制所存在的问题,最后展望了未来溴代二噁英类化合物的环境研究趋势.     

Polychlorinated dibenzo-p-dioxins and dibenzofurans in Great Barrier Reef (Australia) dugongs (Dugong dugon)

Fat tissue samples from dugong (Dugong dugon) carcasses stranded at three sites along the Great Barrier Reef were analysed for polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Relatively high levels of PCDDs were determined in all three dugongs. In particular OCDD, the PCDD/F congener that is usually considered the least bioavailable of all 2,3,7,8 substituted congeners, was found at levels higher than reported for other marine mammals. Tissue accumulation of PCDDs by dugongs may be a consequence of sediment and/or seagrass ingestion during feeding, microbial biotransformation of PCDD precursors in the animal's hindgut or, alternatively, the possession of a selective degradation capability for PCDFs.     

“Shorthand” numbering of chlorinated dibenzodioxins (CDD) and dibenzofurans (CDF)

Numbers in base 16 (Hex) are used for an abbreviated designation of chlorine substitution in CDD and CDF. This “shorthand” requires two hexadecimal digits. A letter (“d” or “f”) may be used to distinguish between CDD and CDF. The digits describe the substitution patterns in positions 6,7,8,9, and 4,3,2,1, assigned values of 8,4,2, and 1, respectively. For example, 66d = 2,3,7,8-tetrachlorodibenzo-p-dioxin.     

The formation of polychlorinated dibenzo-p-dioxins/dibenzofurans from carbon model mixtures containing ferrous chloride

The potential to form polychlorinated dibenzo-p-dioxins/furans (PCDD/F) was investigated in carbon model systems containing ferrous chloride tetrahydrate and a matrix representative of that found in particle emission from the catalytic extraction process (CEP) for wastes. Various types of carbons were used resulting in different PCDD/F yields but, with one exception, similar homologue distributions. Due to the similarity between the turbostratic structure of the carbon in the representative CEP dusts and the carbon blacks used in the model system, experiments were performed using two carbon blacks (termed CBA and CBB). On a mass basis, CBB was more reactive over the temperature range of 275-325 degrees C and reaction times of 20-60 min in the formation of PCDD/F; as well as more adsorptive in terms of the desorption of PCDD/F. On a volume basis, the reactivities and adsorptivities were similar. A maximum in PCDD/F formation occurred at an oxygen concentration of 2% in nitrogen.     

Atmospheric bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the vicinity of an iron and steel making plant

An IRA-743 resin bulk sampler was validated to monitor long-term bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Six consecutive sampling campaigns (2008-2009) were conducted at four sites around steel complexes in Pohang, South Korea to investigate spatial and seasonal variations of PCDD/F bulk deposition. The bulk deposition within the steel complex showed the highest ∑_4-8PCDD/F (Tetra-Octa) fluxes, ranging from 204 to 608 (mean: 352) pg m⁻² d⁻¹, indicating steel complexes were major sources of PCDD/Fs. The homologue profiles were dominated with lower chlorinated PCDFs. Furthermore, the prevailing winds were confirmed to influence the spatial distribution of PCDD/F deposition. There were apparent seasonal variations of the bulk deposition at each site, and seasonal homologue patterns of PCDD/Fs were clearly observed. According to the passive air sampling, however, no significant seasonal change of ambient air concentrations of PCDD/Fs was observed. Therefore, it was concluded that the seasonal variations of deposition fluxes of PCDD/Fs probably resulted from temperature-dependent gas/particle partitioning.     

Dry deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in ambient air

The PCDD/Fs in the ambient air associated with concentration and dry deposition flux of four seasons were characterized in rural area. The mean PCDD/F concentrations were 0.342, 0.221, 0.675, 0.741 pg m(-3) and the mean I-TEQ values were 0.027, 0.016, 0.024, 0.063 pg m(-3) in spring, summer, fall and winter, respectively. Ambient air in winter was higher by a factor of 3.4 and 3.9 for PCDD/F concentration and I-TEQ, respectively, than in summer. The study area is located in a Tropical region. Hence, domestic heating is not found in this area and is not responsible for the elevated winter concentration in comparison to other studies. A smooth plate with a sharp leading edge that is pointed into the wind by a wind vane was used for measuring dry deposition flux of PCDD/Fs. Atmospheric dry deposition fluxes of total PCDD/Fs were 140, 116, 137, and 207 pg m(-2)day(-1) in spring, summer, fall, and winter, respectively, and averaged approximately 150 pg m(-2)day(-1). The total dry deposition flux was found to decrease as the temperature increased. Calculated dry deposition velocities of total PCDD/Fs were 0.45, 0.52, 0.32 and 0.39 cm s(-1) in spring, summer, fall, and winter, respectively, and averaged 0.42 cm s(-1).     

Polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs) and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPXDD/Fs) in the atmosphere and bulk deposition in Kyoto, Japan

Polybrominated diphenyl ethers (PBDEs), polybrominated dibenzo-p-dioxins/dibenzofurans (PBDD/Fs) and monobromo-polychlorinated dibenzo-p-dioxins/dibenzofurans (MoBPXDD/Fs) in atmosphere, bulk atmospheric deposition and soil in Kyoto, which is an urban city in Japan, were measured. Decabromodiphenyl ether (D(10)BDE, BDE-209) was detected in relatively high concentrations compared to other PBDE congeners in most samples. Similar results, in which D(10)BDE was predominantly detected, were reported in other studies in Japan. However, these homologue profiles differ from those of studies conducted in North America. The partitioning of semivolatile organic compounds between atmospheric gas phase and particulate-associated phase is an important factor in their environmental behavior. In this study, atmospheric particulate phase fraction (f(P)) of the brominated compounds increased with increasing bromine number, and f(P) was higher in samples collected in winter than in those collected in summer. Moreover, f(P) of PBDFs and MoBPXDFs was higher than that of PCDFs with the same halogen number. These results agree well with expectations from the vapor pressure of the brominated compounds and PCDD/Fs. Among the brominated compounds in the atmosphere, the level of MoBPXDD/Fs correlates positively with that of PCDD/Fs. This relationship has been previously observed in waste incineration samples. These results suggest that one of the sources of MoBPXDD/Fs in the atmosphere is incineration byproduct. The level of PBDD/Fs seems to correlate positively with that of PBDEs. This relationship suggest that the PBDD/Fs in the atmosphere relate to PBDEs, which is an impurity of PBDE products, or formed by the manufacture or combustion of plastics containing PBDEs.     

Formation of chlorinated phenols, dibenzo-p-dioxins, dibenzofurans, benzenes, benzoquinnones and perchloroethylenes from phenols in oxidative and copper (II) chloride-catalyzed thermal process

Formation of polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs), and chlorinated phenols on CuCl(2) from unsubstituted phenol and three monochlorophenols was studied in a flow reactor over a temperature range of 100-425 degrees C. Heated nitrogen gas streams containing 8.0% oxygen were used as carrier gas. The 0.00024mol of unsubstituted phenol and 0.00039mol of each monochlorophenol were passed through a 1g and 1cm SiO(2) particle containing 0.5% (Cu by mass) CuCl(2). Chlorination preferentially occurred on ortho-(2, 6) and para-(4) positions. Chlorination increased up to 200 degrees C, and thereafter decreased as temperature increased. Chlorination of phenols plays an important role in the formation of the more chlorinated PCDD/Fs. Chlorinated benzenes are formed possibly from both chlorination of benzene and chlorodehydroxylation of phenols. Chlorinated phenols with ortho chlorine formed PCDD products, and major PCDD products were produced via loss of one chlorine. For PCDF formation, at least one unchlorinated ortho carbon was required.     

Atmospheric deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in Guangzhou,China

Atmospheric deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) was investigated at four locations, namely at Yuancun, Wushan, Haizhu and Changban in Guangzhou City, Guangdong Province. The annual deposition fluxes of tetra- to octa-CDD/Fs (total PCDD/Fs) were found to range from 170 to 3000 (mean 1500) pg m⁻² day⁻¹, and the fluxes of total 2, 3, 7, 8-substituted PCDD/F congeners ranged from 2.1 to 41 (mean 20) pg WHO-TEQ m⁻² day⁻¹ at Wushan. The average deposition fluxes of total 2, 3, 7, 8-substituted PCDD/F congeners in rainy season were found to be 37, 27 and 28 pg WHO-TEQ m⁻² day⁻¹ at Yuancun, Haizhu and Changban, respectively, and the PCDD/F deposition fluxes behaved obviously higher in rainy season than in dry season. Results from regression analysis showed that number of rainy days, the amount of wet precipitation, PCDD/F concentrations in particles and organic carbon content played important roles in the variation of PCDD/F deposition fluxes. Monthly average temperatures change little over the year. Therefore, it only played a minor role in monthly variation of PCDD/F deposition fluxes. Particle deposition fluxes were generally not considered as the factor that could cause the differences in PCDD/F deposition fluxes between rainy and dry season, but were found to be related with PCDD/F deposition fluxes in rainy season or dry season. It was found that the profiles of PCDD/F homologs or congeners in the samples were the same either spatially or temporally, indicating that the PCDD/F emission sources were similar to one another. The similarities in PCDD/F homolog patterns and the differences in deposition fluxes between samples collected from heavy-traffic roadside and nearby residence house roof indicated that vehicle exhaust might be an important source for PCDD/F in Guangzhou. PCDD/F concentrations and profiles of PCDD/F homologs in atmospheric deposition were compared with those in both total suspended particles in air and soils, and conclusions indicated that atmospheric deposition possibly tended to remove lower-chlorinated DD/Fs from air and was one of sources for PCDD/Fs in soils.     

Atmospheric deposition of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) in urban and suburban areas of Korea

Bulk atmospheric samples (wet and dry) were collected monthly throughout a year at urban and suburban areas of Korea to assess the deposition flux and seasonal variations of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). The PCDDs/DFs deposition fluxes ranged from 1.0 to 3.7 ng TEQ/m²/year in the urban area and from 0.5 to 4.6 ng TEQ/m²/year in the suburban area. The deposition fluxes of PCDDs/DFs in this study were comparable to or lower than those previously reported at different locations. The atmospheric deposition fluxes of particles and PCDDs/DFs in winter tended to be higher than those in summer. However, monthly variations between particle and PCDDs/DFs deposition fluxes were small, and the correlation coefficients between the deposition fluxes of air particles and each homologue group of PCDDs/DFs varied according to the degree of chlorination of the homologue group. The deposition velocity of PCDDs/DFs in the urban area was estimated at 0.04 cm/s, which is a lower value than those found in other studies. The two most likely factors affecting the monthly variation of deposition fluxes are the ambient temperature and the amount of precipitation. In particular, the ambient temperature had an influence on the lower chlorinated homologues of PCDDs/DFs while precipitation had an influence on the higher chlorinated PCDDs/DFs. The PCDDs/DFs profiles in atmospheric deposition bulk samples showed a similar pattern at the urban and suburban sites. The possibility of the loading of PCDDs/DFs by Asian dust events could be partly confirmed by investigation of homologue profiles.     

Polychlorinated dibenzo-p-dioxins and dibenzofurans: Correlation between in vitro and in vivo structure-activity relationships (SARs)

Polychlorinated dibenzofurans (PCDFs) and dibenzo-p-dioxins (PCDDs) elicit a number of common biologic and toxic responses which are triggered by their initial binding to a cytosolic receptor protein. These effects include the induction of several cytochrome P-448 dependent monooxygenases (eg, aryl hydrocarbon hydroxylase, AHH), body weight loss and thymic atrophy. The dose-response effects of selected PCDFs on AHH induction in rat hepatoma H-4-II E cells and cytosolic receptor binding affinities have been determined. The results of these and studies demonstrate the remarkable effects of structure on the activity of PCDFs. A systematic study of each of the four different position for chlorine substitution in the dibenzofuran ring system showed that the toxic and biologic potencies of these compounds varied with respect to differential chlorine substitution at all four position, i.e. C-3(7) > C-2(8) >C-4(6) > C-1(9). SARs for PCDDs confirmed the importance of the lateral CI substituents and also showed that 1,2(or 6,7-) substituted PCDDs were more active than the corresponding 1,3-dichloro analogs. In addition, there were significant decreases in activity with increasing non-lateral CI substitution. The SARs for PCDFs were different from the PCDDs and this was directly related to the asymmetric structure of the former group of compounds.     

A national inventory to estimate release of polychlorinated dibenzo-p-dioxins and dibenzofurans in Portugal

Taking into account current environmental concerns, the main objective of this work focused a national inventory aiming to estimate the amount of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) released in Portugal in 2006. The methodology used was based on the Standardized Toolkit for Identification and Quantification of Dioxins and Furan Releases, developed by UNEP Chemicals, in 2005. The method allows the assessment of the amount of PCDD/PCDF released into the environment along five vectors involving air, water, land, products and residues. Facing some difficulties mainly regarding to the availability of data for some activities known to produce PCDD/PCDF, three scenarios (Sc1 to Sc3) corresponding to lower, central and upper estimates were established. The Sc1 scenario (lower estimate) includes the situations where in case of doubt or scarce information, reduced or none emission values were assumed, Sc2 refers to a central estimate, which is believed to be the most realistic for the Portuguese situation, while Sc3 corresponds to the worst case (upper estimate). The results obtained pointed out that the total amount of PCDD/PCDF emitted in Portugal during the period under analysis was in the range of 51.2-217.9 g TEQ year⁻¹, with the most likely value of 95.2 g TEQ year⁻¹ achieved under the Sc2 scenario. This study also showed that the methodology developed by UNEP Chemicals is a very simple one, and the main difficulty is the availability of data. The main indicators calculated in this study were 8.98 μg TEQ/(year person) by taking into account the total amount of PCDD/PCDF released, and 3.63 μg TEQ/(year person) when only air emissions were considered.     

Disposition of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in two Norwegian epibenthic marine food webs

Polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) are a group of halogenated hydrocarbons, comprising 210 different, theoretically possible congeners. They are relatively hydrophobic and persistent to biodegradation, thereby rendering them subject to bioaccumulation. This study was conducted in Frierfjord and Eidangerfjord in the Grenland fjord system, Norway, heavily polluted by PCDD/PCDF discharges from the magnesium production at Herøya from 1951 to 2001. Pooled samples of surface-sediments and the following organisms were collected for the Frierfjord and Eidangerfjord study areas: common shrimp (Crangon crangon), polychaetes (mainly Nereis diversicolor), shore crab (Carcinus maenas), cod (Gadus morhua), flounder (Platichthys flesus), trout (Salmo trutta), herring (Clupea harengus), benthic amphipods and zooplankton. Concentrations of 2,3,7,8-PCDD/Fs were quantified in pooled samples for all species. The relative abundances of stable isotopes of nitrogen (δ¹⁵N) were evaluated in the organisms as a measure of chemically-derived trophic level. Contrary to earlier studies on other persistent organochlorines, it was found that the concentrations of PCDD/Fs declined with increasing trophic level. Principal Component Analysis (PCA) also showed differences between species in the pattern of PCDD/Fs. Higher chlorinated congeners constituted lower percentages of the PCDD/F-concentrations higher in the food chain as compared to lower trophic levels. In general, congener patterns did not differ between fjords. Infauna (polychaetes) and zooplankton had congener patterns most similar to the pollution source. The results indicate lower accumulation of higher chlorinated congeners in species at higher trophic levels (fish), presumably due to low membrane permeability (high molecular size) and possibly slow transport through intestinal aqueous phases because of low aqueous solubility.