Analysis of halogenated polycyclic aromatic hydrocarbons in urban air, snow and automobile exhaust

Urban air, snow and automobile exhaust samples were extensively cleaned up by open column liquid chromatography. The appropriate fractions were analysed for halogenated polycyclic aromatic hydrocarbons (XPAH) by gas chromatography/negative chemical ionization mass spectrometry (GC/NCIMS). XPAH were found in all three sample types. A urban air sample was found to contain chlorinated pyrenes, fluoranthenes and benzopyrene and brominated pyrenes and fluoranthenes. Furthermore, the concentration of 1-chloropyrene in that air sample was estimated to be 10 pg/m³. XPAH were also found in snow samples taken in the vicinity of a motor-way. Ethylene dibromide and ethylene dichloride, are probably the source of the halogen atoms in the XPAH detected in car exhaust.     

Quantitation of nitro- and dinitropol ycyclic aromatic hydrocarbons in diesel exhaust particulate matter

A method for routine trace analysis of nitropolycyclic aromatic hydrocarbons (nitro-PAH) in diesel exhaust particulate matter is described. Particle extracts are prefractionated by silica high pressure liquid chromatography and the appropriate band analyzed by capillary electron capture gas chromatography. With on-column injection, three dinitropyrene isomers were recovered in the range of 69–85% for fortifications of 10 ug nitro-PAH/g of soot. The high signal-to-noise ratio suggested detection limits of about 2 ug/g for these analytes. Analysis of the Bureau of Standards SRM 1650 diesel particulate sample demonstrated the methods accuracy for 1-nitropyrene determinations as well.     

Determination and comparison of nitrated-polycyclic aromatic hydrocarbons measured in air and diesel particulate reference materials

The National Institute of Standards and Technology has issued numerous environmental matrix standard reference materials (SRMs) for the measurement of polycyclic aromatic hydrocarbons; however, only one SRM (diesel particulate material) was issued with certified and reference values for four nitrated-polycyclic aromatic hydrocarbons (nitro-PAH). The objective of this study was to develop an improved analytical procedure to quantify 28 mononitro- and dinitro-PAHs, including numerous isomers, in air and diesel particulate SRMs. Two air particulate matrix SRMs, SRM 1649a Urban Dust and SRM 1648 Urban Particulate Matter, and fine particulate matter, collected from Baltimore MD for use as an "interim reference material" for the determination of organic contaminants, have been characterized for nitro-PAHs. Concentrations of nitro-PAHs in all three air particulate materials were at the ng/g level with the highest nitro-PAH concentration being 2-nitrofluoranthene (range between 246 and 340 ng/g). For the three diesel particulate-related SRMs, SRM 1650a Diesel Particulate Matter, SRM 1975 Diesel Particulate Extract, and SRM 2975 Diesel Particulate Matter (Industrial Fortlift), concentrations of nitro-PAHs were in the microg/g range, with 1-nitropyrene as the dominant nitro-PAH (range between 18 and 40 microg/g). Distinct nitro-PAH isomer patterns were present between the air and diesel particulate materials. These results will provide isomer identification and reference concentrations for a large number of nitro-PAHs in the existing diesel and air particulate SRMs. Published by Elsevier Science Ltd.     

Factors Influencing the Emissions of Nitrated-Polynuclear Aromatic Hydrocarbons(Nitro-PAH) from Diesel Engines

The potential problem of 1-nitropyrene (1-NP) formation during filter sampling of diesel emissions from dilution tubes is assessed. Rates of formation are calculated using data generated from several independent filter exposure studies. A portion of the 1-NP (12% average) found in participates collected from light-duty (LDD) and heavy-duty diesels (HOD) was found to be due to formation on the filter under average sampling conditions of 10-15/1 dilution at 44°C with 3 ppm NO₂ for 23 min. On the average, the concentration of 1-NP in participates emitted from HDD is 16 times less than that found in LDD run under similiar transient conditions. The average emission rate of 1-NP generated from the LDD and HDD was 4.7 μg/km and 1.5 μg/km, respectively for the vehicles operating under Federal Test Procedure (FTP)-transient conditions. Under operating conditions which increase exhaust temperature (increased speed and load), the concentration of nitro-PAH is significantly reduced with a concurrent increase in the concentration of partially oxidized nitro-PAH and dinitro-PAH. The concentration of 1-NP in the particulates measured from HDD in these dilution tube studies (0.33-0.95 ppm, depending upon engine load) is comparable to that measured in highway tunnel experiments (0.54 ppm average).     

生活污水中糖类测试方法研究

分别用蒽酮比色、苯酚-硫酸及气相色谱法3种测试方法测试了上海市某生活小区生活污水的糖类组成.试验结果表明,蒽酮比色法测试糖类浓度的准确性与精确性优于苯酚-硫酸法,但不能得出污水中糖类的详细组成情况;与蒽酮比色法和苯酚-硫酸法相比,气相色谱法不仅能得出污水中糖类的详细组成,而且还具有较高的精密度.气相色谱法测得的生活污水中各种单糖,如木糖、甘露糖、葡萄糖、半乳糖、鼠李糖、核糖、岩藻糖的质量浓度分别为8.25、 6.02、5.52、4.80、4.44、4.41、2.66 mg/L.     

Determination of tris(4-chlorophenyl)methanol and tris(4-chlorophenyl)methane in fish, marine mammals and sediment

Tris(4-chlorophenyl)methanol (TCP) and tris(4-chlorophenyl)methane (TCPMe) were determined in aquatic organisms and sediment by a method based on Soxhlet extraction, gel permeation chromatography, fractionation over silica and gas chromatography/mass spectrometry (GC/MS) analysis. TCPMe was identified as the 4-substituted isomer after synthesis of this compound. TCP could be determined by GC/MS with negative chemical ionistation (GC/NCI-MS) with a detection limit of 0.02 g kg(-1) and a recovery of 90%. TCP concentrations in marine mammals from the North Sea and Dutch Wadden Sea ranged from 0.2 to 2 mg kg(-1), and those in marine and freshwater fish samples from 0.005 to 0.4 mg kg(-1) on a lipid wt basis. TCP concentrations in two Rhine delta sediment samples were 1.2 and 3.0 microg kg(-1) dry wt, respectively. TCPMe concentrations, determined by GC/MS with electron impact (GC/EI-MS), were 10-50% of the TCP concentration in all samples analysed.     

Application of a permethrin immunosorbent assay method to residential soil and dust samples

A low-cost, high throughput bioanalytical screening method was developed for monitoring cis/trans-permethrin in dust and soil samples. The method consisted of a simple sample preparation procedure [sonication with dichloromethane followed by a solvent exchange into methanol:water (1:1)] with bioanalytical detection using a magnetic particle enzyme-linked immunosorbent assay (ELISA). Quantitative recoveries (83–126 %) of cis/trans-permethrin were obtained for spiked soil and dust samples. The percent difference of duplicate ELISA analyses was within ± 20 % for standards and ± 35 % for samples. Similar sample preparation procedures were used for the conventional gas chromatography/mass spectrometry (GC/MS) analysis except that additional cleanup steps were required. Recoveries of cis/trans-permethrin ranged from 81 to 108 % for spiked soil and dust samples by GC/MS. The ELISA-derived permethrin concentrations were highly correlated with the GC/MS-derived sum of cis/trans-permethrin concentrations with a correlation coefficient (r) of 0.986. The ELISA method provided a rapid qualitative screen for cis/trans-permethrin in soil and dust while providing a higher sample throughput with a lower cost as compared to the GC/MS method. The ELISA can be applied as a complementary, low-cost screening tool to prioritize and rank samples prior to instrumental analysis for exposure studies.     

An enzyme-linked immunosorbent assay for the determination of dioxins in contaminated sediment and soil samples

A 96-microwell enzyme-linked immunosorbent assay (ELISA) method was evaluated to determine PCDDs/PCDFs in sediment and soil samples from an EPA Superfund site. Samples were prepared and analyzed by both the ELISA and a gas chromatography/high resolution mass spectrometry (GC/HRMS) method. Comparable method precision, accuracy, and detection level (8 ng kg(-1)) were achieved by the ELISA method with respect to GC/HRMS. However, the extraction and cleanup method developed for the ELISA requires refinement for the soil type that yielded a waxy residue after sample processing. Four types of statistical analyses (Pearson correlation coefficient, paired t-test, nonparametric tests, and McNemar's test of association) were performed to determine whether the two methods produced statistically different results. The log-transformed ELISA-derived 2,3,7,8-tetrachlorodibenzo-p-dioxin values and log-transformed GC/HRMS-derived TEQ values were significantly correlated (r=0.79) at the 0.05 level. The median difference in values between ELISA and GC/HRMS was not significant at the 0.05 level. Low false negative and false positive rates (<10%) were observed for the ELISA when compared to the GC/HRMS at 1,000 ng TEQ kg(-1). The findings suggest that immunochemical technology could be a complementary monitoring tool for determining concentrations at the 1,000 ng TEQ kg(-1) action level for contaminated sediment and soil. The ELISA could also be used in an analytical triage approach to screen and rank samples prior to instrumental analysis.     

Comparison of an enzyme-linked immunosorbent assay (ELISA) to gas chromatography (GC)--measurement of polychlorinated biphenyls (PCBs) in selected US fish extracts

The analysis of PCBs in fish tissues by immunoassay methods was evaluated using fish collected from a US monitoring program, the National Contaminant Biomonitoring Program of the US Department of Interior, Fish and Wildlife Service. Selected composite whole fish samples, which represented widely varying concentrations and sources of PCBs, were extracted and subjected to congener PCB analysis by gas chromatography (GC) and total PCB analysis using an ELISA (ePCBs) calibrated against technical Aroclor 1248. PCB congener patterns in these fishes were different from the patterns found in commercial Aroclors or their combinations as demonstrated by principal component analysis of normalized GC congener data. The sum of the PCB congeners measured by GC (total-PCBs) ranged from 37 to 4600 ng/g (wet weight). Concentrations of PCBs as determined by the ELISA method were positively correlated with total-PCBs and the ePCBs/total-PCBs ratios for individual samples ranged from 1 to 6. Ratios of ePCBs/total-PCBs for dilutions of Aroclors 1242, 1254, and 1260 and for matrix spikes range from 0.6 for 1242 to 2.5 for 1254 and 1260. These results suggest that higher chlorinated PCB congeners have higher affinity for the anti-PCB antibodies. Partial least squares with latent variable analysis of GC and ELISA data of selected Aroclors and fish samples also support the conclusion that ELISA derived PCB concentrations are dependent on the degree of chlorination.     

Occurrence and sources of particulate nitro-polycyclic aromatic hydrocarbons in ambient air in Denmark

The occurrence of selected nitro-polycyclic aromatic hydrocarbons (nitro-PAHs) associated with atmospheric particulate matter has been investigated at an urban site and at a semi-rural site. For this purpose an analysis method based on gas chromatography and tandem ion trap mass spectrometry has been developed and applied. The nitro-PAH levels have been compared with levels of other air pollutants including unsubstituted PAHs, inorganic gases and particulate matter, as well as with meteorological parameters. Correlations and concentration ratios suggest that the dominant source of 9-nitroanthracene at the urban site is direct emissions, whereas at the semirural site its dominant source is atmospheric formation. The atmospheric formation of 2-nitrofluoranthene and 2-nitropyrene generally seems to be initiated by OH radicals during the day rather than by NO₃ radicals at night. The average contribution of the OH initiated formation is estimated to be in the range of 90–100%. However, under wintertime conditions with cloudy weather implying low OH radical production, NO₃ radicals may also be important as initiators of nitro-PAH formation. Samples influenced by transport of polluted air masses from the European continent have significantly elevated concentrations of atmospherically formed nitro-PAHs. The directly emitted nitro-PAHs, 1-nitropyrene and 3-nitrofluoranthene, do not exhibit elevated levels during such long-range transport episodes.     

Nitration of polycyclic aromatic hydrocarbons adsorbed to different carriers in a fluidized bed reactor

The reactivity of selected polycyclic aromatic hydrocarbons (PAH) adsorbed to various surfaces has been studied. PAH were adsorbed to silica, alumina or charcoal particles and exposed to ambient concentrations of NO₂ in air in a fluidized bed reactor. The reaction products were analyzed by capillary gas chromatography and gas chromatograpy/mass spectrometry.The results show that silica is a more reactive surface than alumina. The charcoal used showed to be very adsorbtive and too little material was recovered for analyses. The reactivity of the PAH compounds studied decrease in the order perylene > benzo(a)pyrene > pyrene > chrysene > fluoranthene and phenanthrene. The relevance of these results to the assessment of the possible formation of nitro-PAH in the atmosphere is discussed.     

Mutagenicity of Airborne Particulates Assessed by Salmonella Assay and the SOS Chromotest in Wrocław,Poland

Abstract

Ambient air particulate matter less than 2.5 μm in aerodynamic diameter (PM_2.5) samples were collected during summer and autumn using a Staplex high-volume air sampler. They were later extracted with dichloromethane in a Soxhlet apparatus. Polyaromatic hydrocarbon (PAH) content in extracts was determined by the high-performance liquid chromatography technique using fluorescence detection, whereas the nitro-PAH content was determined by gas chromatography using mass detection. Four Salmonella typhimurium strains (TA98, TA100, YG1041, and YG1042) were used in assays conducted with and without metabolic activation. The extracts were also tested with the SOS chromotest supplied by Environmental Biodetection Products Incorporated. The obtained results confirmed the Salmonella assay and the SOS chromotest usability for the purpose of atmospheric pollution monitoring within an urban agglomeration. The atmospheric pollution extracts under examination differed among each other regarding total content and percentage of individual compounds, depending on the season of sampling. The highest total PAH content and the highest nitro-PAH content in the tested samples as well as the most extensive range of detected compounds were found in the autumn season (heating season). The highest mutagenicity was noted for PM_2.5 samples collected in autumn. The high values of mutagenicity ratios and induction factors were obtained from assays carried out with and without metabolic activation, which is an argument for the presence of promutagens and direct mutagens. The YG1041 strain proved to be the most effective in detection of mutagenicity of the suspended dust extracts because of its notably high sensitivity to nitro-aromatic compounds. The SOS chromotest was very sensitive to a large spectrum of genotoxic air pollutants and showed a high degree of similarity with the results of the Salmonella assay. In comparison with the frequently used Ames test, the SOS chromotest enables quick analysis of the genotoxic effects of samples using only one tester strain. In addition, its miniaturized design decreases the consumption of tested samples.     

Reductive degradation of nitrobenzene in aqueous solution by zero-valent iron

The reductive degradation of nitrobenzene (NB) by zero-valent iron was investigated. Experimental results showed that the degradation of NB was influenced by pH and NB concentration. The optimum pH value was found to be 3.0 for the reductive degradation of NB in the tested pH ranges of 3.0-12.0. The formation rate of aniline, a major reductive product of NB, followed zero-order kinetics at various pH levels. Furthermore, GC/MS analysis showed that aniline, azobenzene and azoxybenzene were the reductive products of NB by zero-valent iron. With the analysis of the products with GC/MS and FTIR, possible reductive pathways of NB by zero-valent iron were suggested.     

Evaluating peats for their capacities to remove odorous compounds from liquid swine manure using headspace "solid-phase microextraction".

This paper reports on research designed to investigate the capacities of different highly characterized peats to remove odorous compounds from liquid swine manure (LSM). Peat types representing a wide range of properties were tested in order to establish which chemical and physical properties might be most indicative of their capacities to remediate odors produced by LSM. Eight percent slurries (of peat/LSM) were measured for odor changes after 24 hours using odor panel and GC/MS-Solid-phase microextraction (GC/MS-SPME) analysis. The GC/MS-SPME and odor panel results indicated that, although all peats tested in this study were found to be effective at removing odor-causing compounds found in LSM, some peats tended to work better than others. Overall, the peats that were the most effective at removing odor-causing compounds tended to have lower bulk densities, ash contents, fulvic acids contents, and guaiacyl lignins contents, and higher water holding capacities, hydraulic conductivities, "total other lignins" contents, hydrogen contents, carbon contents, and total cellulose contents. GC/MS-SPME analysis was found to be a reasonably inexpensive and efficient way of conducting this type of research. It allows one to identify a large number of the odor-causing compounds found in LSM, and more importantly, to detect with some precision specific differences in the amounts of these compounds between peat types.     

Comparison of dioxin and furan TEQ determination in contaminated soil using chemical,micro-EROD,and immunoassay analysis

High resolution mass spectrometry gas chromatography (GC/MS) is the standard method for dioxin and furan analysis in environmental matrices. Considered as very accurate, this method is however time consuming and expensive. Methods based on biological interactions have the necessary sensitivity but began only recently to be investigated in the context of environmental applications. We have compared dioxin and furan toxicity levels (expressed as toxic equivalent quantities (TEQs)) in soil samples by three analytical approaches: the micro-ethoxyresorufin-o-deethylase (EROD) bioassay (a receptor-based method), an immunoassay (antibody-based method) and GC/MS analysis (used as a reference) using a shortened extraction-purification method. Both biological methods were sensitive to interferences from compounds co-extracted from samples. Most samples were underestimated by the immunoassay and, at a greater extent, overestimated by the EROD bioassay. The average accuracy of TEQ estimation (86 +/- 45% of values established by GC/MS) and the absence of false-negatives showed by the immunoassay suggest the usefulness of this method for semi-quantitative, preliminary characterization of potentially contaminated sites.     

Analysis of nitrated polynuclear aromatic hydrocarbons

A derivatization-gas chromatography/electron capture detector (GC/ECD) method has been developed for the measurement of trace nitrated polynuclear aromatic hydrocarbons (NPAHs) in air. The method involves first the derivatization of parent nitro-PAHs to their corresponding fluorinated derivatives, followed by GC/ECD analysis. The sensitivity of the method is an order of magnitude higher than those of direct GC/ECD analysis of NPAHs themselves. The method is simple and robust and thus ideally suited for the routine monitoring of NPAHs in air samples. The sensitivity and reproducibility of GC/negative ion chemical ionization MS (NICIMS) for the measurement of NPAHs after derivatization has been evaluated. The method has sensitivity comparable to GC/ECD, but is less reproducible in quantification. The method is therefore suitable for method validation and NPAHs peak confirmation rather than routine operations.     

Joint representation of physical locations and volatile organic compounds in indoor air from a healthy and a sick building

Many modern, energy-efficient buildings have been labeled “sick”, in view of the fact that their occupants display an unusually large number of sensory symptoms (e.g. eye irritation, dry skin and perception of persistent odors). Air samples were taken from locations (17) in two Stockholm preschools, one considered healthy, the other, sick. The samples (170) were analyzed by gas chromatography/mass spectrometry (GC/MS) and 33 volatile organic compounds were identified and quantified by GC peak heights. The relationship between chemicals and locations in the two preschools was represented spatially by correspondence analysis and other statistical techniques. The analyses clearly distinguish among the buildings and among locations within each building, including whether the sample was collected outdoors or indoors. Within the sick preschool, concentrations of light aromatic hydrocarbons increased with distance from the air supply, but there was no similar gradient in the healthy preschool. The chief results obtained by the comparatively new method of correspondence analysis are supported further by a discriminant analysis and a principal components analysis.     

Analysis of pesticide runoff from mid-Texas estuaries and risk assessment implications for marine phytoplankton

During 1993, estuarine surface water samples were collected from the mid-Texas coast (Corpus Christi to Port Lavaca, TX). Agricultural watershed areas as well as tidal creeks immediately downstream were chosen as sampling sites along with adjoining bay sampling stations. Collections were made throughout the growing season (February to October 1993) before and after periods of significant (> 1.25 cm) rainfall. All samples were initially screened for the presence of pesticides using enzyme-linked immunosorbent assay (ELISA) test kits (EnviroGard) for triazine herbicides and carbamate insecticides. All samples were extracted and then analyzed using gas chromatography (GC) for quantification of atrazine. Only samples testing positive for carbamate insecticides via ELISA were further extracted for GC analysis to quantify aldicarb and carbofuran. Additionally, laboratory toxicity tests using phytoplankton were examined from published, peer-reviewed literature and compared with the atrazine field levels found in Texas. Results of ELISA screening indicated the presence of triazine herbicides in nearly all samples (>93%). GC analysis further confirmed the presence of atrazine concentrations ranging from <0.01-62.5 microg/L. Screening tests also found detectable levels of carbamate insecticides (aldicarb and carbofuran) that were also confirmed and quantified by GC. Comparison of measured concentrations of atrazine compared with published toxicity tests results indicated that there was a potential environmental risk for marine/estuarine phytoplankton in surface waters of Texas estuaries, particularly when the chronic nature of atrazine exposure is considered.     

Inter-comparison of three instruments for measuring regional background carbon monoxide

Three CO instruments, i.e., vacuum ultraviolet resonance fluorescence (VUV-RF), gas chromatography/reduction gas detection (GC/RGD), and non-dispersive infrared (NDIR) spectrometry, were inter-compared at a background site, i.e., Lulin Atmospheric Baseline Station (LABS) in central Taiwan. For a period of 18 days of continuous measurements, highly coherent results were observed between the three instruments. Calibration of the GC/RGD and VUV-RF was based on the same batch of CO standards, producing results that agreed within 4%. Nevertheless, NDIR displayed a significant bias with a large offset compared to the other two instruments (about ?63.1 ppb), due mainly to its over-simplified calibration procedure. The NDIR bias was then removed by aligning the NDIR data to those of GC/RGD in a process termed “post-run correction”. Through this practice, the NDIR was linked to the same calibration scale as that of GC/RGD. As a result, by simultaneously exploiting both GC/RGD and NDIR to measure background CO, both time-resolution and accuracy can be secured.     

Catalyzed dehalogenation of Delor 103 by sodium hydridoaluminate

The complete dechlorination of PCB liquid Delor 103 (42.6% Cl) to biphenyl has been effected in toluene with sodium dihydridobis(2-methoxyethoxo)aluminate (SDMA) in the presence of catalytic amounts of Ni(II) and Co(II) 2,4-pentanedionates at elevated temperatures. Changes in PCB congeners distribution during dechlorination were monitored by GC(ECD) and GC/MS, and the scheme of their transformation was proposed on the basis of site selectivity observed. A kinetic analysis of the reaction is presented.