Rapid resolution liquid chromatography-tandem mass spectrometry method for the determination of endocrine disrupting chemicals (EDCs), pharmaceuticals and personal care products (PPCPs) in wastewater irrigated soils

A multiresidue analytical method was developed for the determination of 9 endocrine disrupting chemicals (EDCs) and 19 pharmaceuticals and personal care products (PPCPs) including acidic and neutral pharmaceuticals in water and soil samples using rapid resolution liquid chromatography-tandem mass spectrometry (RRLC-MS/MS). Solid phase extraction (SPE), and ultrasonic extraction combined with silica gel purification were applied as pretreatment methods for water and soil samples, respectively. The extracts of the EDCs and PPCPs in water and soil samples were then analyzed by RRLC-MS/MS in electrospray ionization (ESI) mode in three independent runs. The chromatographic mobile phases consisted of Milli-Q water and acetonitrile for EDCs and neutral pharmaceuticals, and Milli-Q water containing 0.01 % acetic acid (v/v) and acetonitrile: methanol (1:1, v/v) for acidic pharmaceuticals at a flow rate of 0.3 mL/min. Most of the target compounds exhibited signal suppression due to matrix effects. Measures taken to reduce matrix effects included use of isotope-labeled internal standards, and application of matrix-match calibration curves in the RRLC-MS/MS analyses. The limits of quantitation ranged between 0.15 and 14.08 ng/L for water samples and between 0.06 and 10.64 ng/g for solid samples. The recoveries for the target analytes ranged from 62 to 208 % in water samples and 43 to 177 % in solid samples, with majority of the target compounds having recoveries ranging between 70–120 %. Precision, expressed as the relative standard deviation (RSD), was obtained less than 7.6 and 20.5 % for repeatability and reproducibility, respectively. The established method was successfully applied to the water and soil samples from four irrigated plots in Guangzhou. Six compounds namely bisphenol-A, 4-nonylphenol, triclosan, triclocarban, salicylic acid and clofibric acid were detected in the soils.     

Octyl and nonylphenol ethoxylates and carboxylates in wastewater and sediments by liquid chromatography/tandem mass spectrometry

This work presents an LC–MS–MS-based method for the quantitation of nonylphenol ethoxylates (NPEOs) and octylphenol ethoxylates (OPEOs) in water, sediment, and suspended particulate matter, and three of their carboxylated derivatives in water. The alkylphenol ethoxylates (APEOs) were analyzed using isotope dilution mass spectrometry with [¹³C₆]-labeled analogues, whereas the carboxylated derivatives were determined by external standard quantitation followed by confirmation using standard additions. The method was used to study APEO’s behavior in a wastewater treatment plant (WWTP), where total dissolved NP0-16EO concentration was reduced by approximately 99% from influent (390 μg l⁻¹) to final effluent (4 μg l⁻¹), and total OP0-5EO concentration decreased by 94% from 3.1 to 0.2 μg l⁻¹. In contrast, the carboxylated derivatives were formed during the process with NP0-1EC concentrations increasing from 1.4 to 24 μg l⁻¹. Short-chain APEOs were present in higher proportions in particulate matter, presumably due to greater affinity for solids compared to the long-chain homologues. NP (0.49 μg l⁻¹) and NP0-1EC (4.8 μg l⁻¹) were the only APEO-related compounds detected in a surface water sample from a WWTP-impacted estuary; implying that 90% of the mass was in the form of carboxylated derivatives. Sediment analysis showed nonylphenol to be the single most abundant compound in sediments from the Baltimore Harbor area, where differences in homologue distribution suggested the presence of treated effluent in some of the sites and non-treated sources in the rest.     

Occurrences of pharmaceutical and personal care products as micropollutants in rivers from Romania

The occurrence of pharmaceutical and personal care products (PPCPs) was investigated in the Somes River. The aim of this study was to obtain a first overview about the contamination of Somes River (Transylvania) with PPCPs. The samples were preconcentrated by Solid Phase Extraction (SPE) procedures and analysed by GC/MS. A number of 15 compounds including pharmaceutics, metabolites, intermediates and musk fragrances were detected in concentration ranging from 30 ng/l to 10 μg/l. The detected pharmaceuticals are included in following therapeutic groups: analgesics, antiepileptics, psychiatric, stimulants, anticoagulants, antineoplastic and disinfectants.     

Development of a fast instrumental method for the analysis of pharmaceuticals in environmental and wastewaters based on ultra high performance liquid chromatography (UHPLC)-tandem mass spectrometry (MS/MS)

This work describes the development, optimization and validation of an analytical method for the simultaneous detection and identification of 74 pharmaceutically active compounds (PhACs), from various therapeutic groups, in both environmental (ground and surface water) and wastewaters (WW). The method is based on the simultaneous extraction of all target compounds by solid phase extraction (SPE), using a hydrophilic-lipophilic balanced polymer followed by ultra high performance liquid chromatography (UHPLC) tandem mass spectrometry (MS/MS). Two selected reaction monitoring (SRM) transitions have been monitored per compound in order to fulfil the EC guidelines, as well as to ensure an accurate identification of target compounds in the samples. Quantification is performed by internal standard approach, applying 24 specific isotopically labeled compounds. The main advantages of the developed method, besides the selectivity and reliability of the results, is its high throughput. All compounds are extracted in a single step and the instrumental analysis lasts 5 min (NI mode) + 8 min (PI mode), allowing fast throughput of samples. The limits of detection range from 0.01 to 50 ng L⁻¹, depending on the matrix, for most of the compounds. Finally, the method developed has been applied to the analysis of pharmaceuticals in the Ebro river basin (NE Spain).     

Distribution of pesticides and bisphenol A in sediments collected from rivers adjacent to coral reefs

To investigate the deteriorating health of coral reefs in Okinawa, Japan, natural sediment samples were analyzed for diuron, Irgarol 1051, chlorpyrifos, and bisphenol A (BPA) which are hazardous to corals. Samples were analyzed by solid-phase extraction (SPE) followed by high-performance liquid chromatography with tandem mass spectrometry (LC–MS–MS). Although diuron and chlorpyrifos usage is only well recorded for farms and not for cities, these chemicals were detected in both rural and urban areas. Additionally, diuron concentration in urban areas was in some cases higher than in rural areas, which might be caused by greater consumption of these chemicals in home gardens in city areas. Irgarol 1051 was detected in downstream river areas, which are situated far from the source sites such as pier or fishery harbor (0.6–3.2 km). This result suggested that Irgarol 1051 could be transported from the river mouths to the sampling sites during flood tides. High BPA concentrations were associated with urban areas (<1.2–22.0 μg kg⁻¹), while low concentrations were associated with rural areas (nd–6.8 μg kg⁻¹). The river sediments under study are delivered to coral reefs in large quantity through runoff caused by typhoons and other heavy rains. The highly hazardous chemicals are carried into coral reefs on these sediments. Therefore, these hazardous chemical substances may already be influencing the coral reefs.     

Screening 31 endocrine-disrupting pesticides in water and surface sediment samples from Beijing Guanting reservoir

For screening 31 potential or suspected endocrine-disrupting pesticides in water and surface sediments, a multiresidue analysis method based on gas chromatography with electron capture detection (GC/ECD) was developed. Solid phase extraction (SPE) technology with Oasis^® HLB cartridge was also applied in sample extraction. The relevant mean recoveries were 70–103% and 71–103% for water and sediment, respectively. Relative standard deviations (RSD) are 2.0–7.0%, 4.0–8.0% for water and sediment, respectively. Thirty one pesticides (-HCH, β-HCH, γ-HCH, δ-HCH, hexachlorobenzene (HCB), aldrin, heptachlor, endosulfan I & II, p,p′-DDD, o,p′-DDT, p,p′-DDT, p,p′-DDE, endrin aldehyde, endosulfan sulphate, methoxychlor, hepachlor epoxide, -chlordane, γ-chlordane, dieldrin, endrin, dicofol, acetochlor, alachlor, metolachlor, chlorpyriphos, nitrofen, trifluralin, cypermethrin, fenvalerate, deltamethrin) in water and surface sediment samples from Beijing Guanting reservoir were analyzed. Concentrations of pesticides ranged from 7.59 to 36.0 ng g⁻¹ on a dry wt. basis for sediment samples, from 279.3 to 2740 ng l⁻¹ for pore waters and from 48.8 to 890 ng l⁻¹ for water samples, respectively, with a mean concentration of 10.7 ng g⁻¹ in sediment, 735 ng l⁻¹ in pore water and 295 ng l⁻¹ in water, respectively. The data obtained provides information on the levels and sources of endocrine-disrupting pesticides in Guanting reservoir. These results underscore the need to improved environmental protection measures in order to reduce the exposure of the population and aquatic biota to these endocrine-disrupting compounds.     

Characterizing the passage of personal care products through wastewater treatment processes.

Wastewater treatment facilities use secondary treatment to stabilize the effect of discharged effluent on receiving waters by oxidizing biodegradable organic matter and reducing suspended solids and nutrients. The process was never specifically intended to remove trace quantities of xenobiotics, such as endocrine-disrupting compounds (EDCs) and pharmaceuticals and personal care products (PPCPs). Nevertheless, European studies performed at bench-scale or at small facilities have demonstrated that a critical minimum solids retention time (SRT) can achieve good reduction of many EDCs and pharmaceuticals. The objective of this study was to expand these findings to the removal performance for 20 PPCPs commonly found in the influent to full-scale facilities operating in the United States. The participating plants use SRT conditions ranging from 0.5 to 30 days and include facility capacities ranging from 19 000 m3/d (5 mgd) to greater than 1 136 000 m3/d (300 mgd). Two pilot membrane bioreactors were also included in the study. The 20 PPCPs were categorized into nine bin combinations of occurrence frequency and treatment reduction performance. While most compounds were well removed, galaxolide (a musk fragrance) occurred frequently and was resistant to removal. A minimum critical SRT, defined as the minimum SRT, needed to consistently demonstrate greater than 80% removal (SRT80), was compound-dependent, with most compounds removed at 5 to 15 days and a small group requiring longer SRTs. From limited data, no additional removal could be attributed to the use of membrane bioreactors, media filters, or longer hydraulic retention times. Reverse osmosis was effective in removing any remaining compounds.     

Determination of 4-tert-octylphenol, 4-nonylphenol and bisphenol A in surface waters from the Haihe River in Tianjin by gas chromatography-mass spectrometry with selected ion monitoring

The estrogenic pollutants 4-tert-octylphenol (OP), 4-nonylphenol (NP) and bisphenol A (BPA) were determined in surface water samples from the Haihe River, Tianjin, China. The analytes were extracted and concentrated from 300 ml acidified water samples by liquid–liquid extractions using dichloromethane, derivatized with trifluoroacetic anhydride, and quantified by gas chromatography–mass spectrometry (GC–MS) with selected ion monitoring (SIM). Among the samples collected from 14 sampling sites, only one sample was found to have a relatively high concentration of BPA (8.30 μg l⁻¹) and NP (0.55 μg l⁻¹). The concentrations of OP, NP and BPA in the other samples were in the range of 18.0–20.2, 106–296 and 19.1–106 ng l⁻¹, respectively. Recoveries for OP, NP and BPA in the spiked water samples were all over 80%.     

Nonylphenols in freshwaters of the hydrologic system of an Italian district: association with human activities and evaluation of human exposure

A sampling campaign for the determination of concentrations of nonylphenol isomers (NPs) in freshwaters and sediments of the hydrologic system of the Rieti district (central Italy) was conducted from 2002 to 2003. Eighteen sampling points, selected on the basis of the different human activities in the vicinity, were monitored; six series of water samples (from June 2002 to February 2003) and one of sediment samples (summer 2002) were analyzed by GC/MS.

There was a direct relationship between concentrations of NPs and the presence of urban or industrial activities near the sampling point. However, concentrations of NPs in water were in the range of <0.1–1.4 μg l⁻¹, and their presence limited to short distances from the sources of contamination. Accumulation factors in sediment samples ranged from 10² to 5 × 10³.     

Distribution of endocrine disruptors in the Llobregat River basin (Catalonia, NE Spain)

The Llobregat basin is a Mediterranean fluvial system with major agricultural, urban and industrial impacts. We combined chemical quantification by liquid chromatography–mass spectrometry with electrospray interface (LC-ESI-MS) and the recombinant yeast assay (RYA) assays to estimate the loads of endocrine disrupting compounds (EDCs) along the basin. Chemical analysis revealed maximum concentrations (at μg l⁻¹ level) of alkylphenols at the lower course of the Llobregat River, which correlated with high levels of estrogenic activity detected by RYA. Analysis by RYA and LC-ESI-MS of influent and effluent waters from four sewage treatment plants (STP) discharging into the basin showed the removal of 80–95% of EDCs by STP treatment. Chemical analysis data and RYA data showed a quasi-linear correlation, demonstrating the complementariness of both methods. Our data suggest that the concentrations of the analysed compounds were enough to explain the total estrogenicity of water and STP samples from the Llobregat basin.     

Determination and distribution characteristics of degradation products of nonylphenol polyethoxylates in the rivers of Taiwan

Concentrations of degradation products of nonylphenol polyethoxylates (NPEOs) were analyzed in river water samples in order to determine the distribution characteristic of these alkylphenolic compounds in 18 major rivers of Taiwan. The degradation products of NPEOs were detected in all river samples, with the dicarboxylates alkylphenolic degradation products (CAPEC) being detected most frequently and at the highest concentrations. Concentrations of NP and NP1EO in rivers ranged from n.d. to 5.1 μg l⁻¹ and n.d. to 0.5 μg l⁻¹, respectively. The total concentrations of shortened carboxylates (i.e., NP1EC + NP2EC + NP3EC) and dicarboxylates alkylphenolic degradation products (CAP1EC + CAP2EC) ranged from n.d. to 63.6 μg l⁻¹ and n.d. to 94.6 μg l⁻¹, respectively. Concentrations of NP2EC, NP3EC and all CAPEC residues were determined semi-quantitatively by comparing with the internal standard. Significantly higher concentrations of CAPEC residues were detected in the river waters as compared to those of NP, NP1EO and NPEC degradation products and the average proportions of these compounds in the samples of the rivers were as follows: NP + NP1EO was 5 ± 2.5%, total NPEC was 25 ± 12%, and total CAPEC was 70 ± 12%. The high concentration ratios of CAPEC/NPEC illustrate that aerobic biodegradation plays a main route in the fate of NPEO in the rivers of Taiwan.     

Leaching and degradation of 21 pesticides in a full-scale model biobed

Filling and cleaning of pesticide sprayers presents a potential risk of pollution of soil and water. Three different solutions for handling sprayers have been suggested: Filling and cleaning in the field, filling and cleaning on hard surfaces with collection of the waste water, and filling and cleaning on a biobed, which is an excavation lined with clay and filled with a mixture of chopped straw, sphagnum and soil with turf on top, and with increased sorption capacity and microbial activity for degradation of the pesticides. In the present study the degradation and leaching of 21 pesticides (5 g of each) was followed in an established full-scale model biobed. Percolate was collected and analysed for pesticide residues, and the biobed material was sampled at three different depths and analysed by liquid chromatography double mass spectrometry (LC-MSMS). During the total study period of 563 days, no traces of 10 out of 21 applied pesticides were detected in the percolate (detection limits between 0.02 and 0.9 μg l⁻¹) and three pesticides were only detected once and at concentrations below 2 μg l⁻¹. During the first 198 days before second application, 14% of the applied herbicide bentazone was detected in the leachate with maximum and mean concentrations of 445 and 172 μg l⁻¹, respectively. About 2% of the initial mecoprop and fluazifop dose was detected in the percolate, with mean concentrations of 23 μg l⁻¹, while MCPA and dimethoate had mean concentrations of 3.5 and 4.7 μg l⁻¹, respectively. Leachate concentrations for the remaining pesticides were generally below the detection limit (0.02–0.9 μg l⁻¹, below 1% of applied). Sorption studies of five pesticides showed that compounds with a low K_d value appeared in the leachate. After 169 days, all pesticides in the biobed profile were degraded to a level below 50% of the calculated initial dose. Pesticides with K_oc values above 100 were primarily found in the uppermost 10 cm and degraded slowest due to the low bioavailability. The 11 most degradable pesticides were all degraded such that less than 3% remained in the biobed after 169 days.

Following second pesticide application of the biobed, leachate was sampled 215 and 365 days after the treatment. This showed the same pesticides to be leached out and at concentrations comparable to those of the first treatment. The same pesticides as after the first treatment were retained in the biobed.     

Determination of dithiocarbamate fungicide propineb and its main metabolite propylenethiourea in airborne samples

A simple, rapid and sensitive GC–MS method for the determination of dithiocarbamate fungicide propineb [polymeric zinc propylenebis (dithiocarbamate)] and an improved HPLC procedure for the simultaneous determination of its main metabolite, propylenethiourea, and ethylenethiourea, the main metabolite of all ethylenedithiocarbamates, in airborne samples are described. The method for the analysis of propineb involves the evolution of carbon disulfide (CS₂), under acidic conditions in the presence of stannous chloride, extraction of the generated CS₂ into a layer of isooctane which is then analyzed for CS₂ content by GC–MS in SIM mode. Under the optimum conditions, the retention time of CS₂ was 1.89 min and the total time of chromatographic analysis was 5 min. Recoveries from spiking glass microfibre filters (GF/A) and silica gel filters were 86 ± 7 (n = 9) and 89 ± 4 (n = 9), respectively. The limit of detection is 0.7 ng per filter, which is equivalent to about 0.8–1.0 ng m⁻³ in air. In parallel, an HPLC method with ultraviolet detection is presented for the simultaneous analysis of the metabolites. Separation of the two metabolites was attained in less than 5 min. Recoveries from spiking GF/A and silica gel filters for ethylenethiourea were 100 ± 1 (n = 3) and 98 ± 2 (n = 3), respectively, while for propylenethiourea were 102 ± 1 (n = 3) and 98 ± 1 (n = 3), respectively. The detection limits are about 36–43 and 40–49 ng m⁻³ in air for ethylenethiourea and propylenethiourea, respectively. All the analytes spiked in the filters are proven to be stable for more than one month, at −4 °C.     

Synthesis of branched para-nonylphenol isomers: occurrence and quantification in two commercial mixtures

Eight tertiary nonanols were synthesized via Grignard reaction and coupled by Friedel–Crafts alkylation with phenol to the corresponding nonylphenols. Six branched para-nonylphenols (NP) were obtained: 4-(3′-methyl-3′-octyl)phenol (33NP), 4-(2′-methyl-2′-octyl)phenol (22NP), 4-(2′,5′-dimethyl-2′-heptyl)phenol (252NP), 4-(2′,5′,5′-trimethyl-2′-hexyl)phenol (2552NP), 4-(2′,4′-dimethyl-2′-heptyl)phenol (242NP) and 4-(4′-ethyl-2′-methyl-2′-hexyl)phenol (4E22NP). Their structures were confirmed by GC–MS and NMR spectroscopy. These six isomers as well as the earlier synthesized 4-(3′,5′-dimethyl-3′-heptyl)phenol (353NP), 4-(3′,6′-dimethyl-3′-heptyl)phenol (363NP) and 4-(2′,6′-dimethyl-2′-heptyl)phenol (262NP) were compared with commercial NP mixtures purchased from Acros and Fluka by GC–MS (equipped with a 100 m polysiloxane column). The analyses revealed that all obtained isomers are occurring in different quantities in both commercial NP mixtures.     

Reactions of the amine-containing drugs fluoxetine and metoprolol during chlorination and dechlorination processes used in wastewater treatment

The reactivities of the amine-containing pharmaceuticals fluoxetine and metoprolol with hypochlorite were studied using conditions that simulate wastewater disinfection including neutral pH (7.0), a range of reaction times (2–60 min), and a molar excess of hypochlorite relative to the pharmaceutical concentration (5.7 times). The reactions were monitored using liquid chromatography (LC) with several detection modes including ultraviolet absorbance (UV), mass spectrometry (MS), and post-column reaction/reductive electrochemistry (EC) for determining active chlorine products. At levels of 10 μM, both compounds reacted rapidly (<2 min) to form principally N-chloramine products that were stable in aqueous solution for at least 1 h. The reaction was also studied in wastewater, and similar reactivity was noted. These results demonstrate that the cations fluoxetine and metoprolol are likely to be rapidly transformed into neutral N-chloramines during wastewater disinfection. The reactivity of the N-chloramines was also studied with sulfite to simulate dechlorination, which is often employed in wastewater treatment. Both N-chloramines reacted slowly with sulfite. In the pure water dechlorination experiments, it was estimated that 70% and 10% of the peak areas remained after 2 min reaction time for fluoxetine and metoprolol, respectively. At longer reaction times both N-chloramines had been completely reduced by sulfite, and the product of the sulfite reduction reaction was the parent pharmaceutical amine. Since typical dechlorination times in wastewater treatment are on the order of seconds, this suggests the chloramines formed from these two basic drugs might evade dechlorination and be released into the environment. The implications of chloramine release are discussed.     

Degradation of organic pollutants in Mediterranean forest soils amended with sewage sludge

The degradation of two groups of organic pollutants in three different Mediterranean forest soils amended with sewage sludge was studied for nine months. The sewage sludge produced by a domestic water treatment plant was applied to soils developed from limestone, marl and sandstone, showing contrasting alkalinity and texture. The compounds analysed were: linear alkylbenzene sulphonates (LAS) with a 10–13 carbon alkylic chain, and nonylphenolic compounds, including nonylphenol (NP) and nonylphenol ethoxylates with one and two ethoxy groups (NP1EO + NP2EO). These compounds were studied because they frequently exceed the limits proposed for sludge application to land in Europe. After nine months, LAS decomposition was 86–96%, and NP + NP1EO + NP2EO decomposition was 61–84%, which can be considered high. Temporal trends in LAS and NP + NP1EO + NP2EO decomposition were similar, and the concentrations of both types of compounds were highly correlated. The decomposition rates were higher in the period of 6–9 months (summer period) than in the period 0–6 months (winter + spring period) for total LAS and NP + NP1EO + NP2EO. Differences in decay rates with regard to soil type were not significant. The average values of decay rates found are similar to those observed in agricultural soils.     

Photodegradation of malachite green under natural sunlight irradiation: kinetic and toxicity of the transformation products

This article describes the photolytic degradation of malachite green (MG), a cationic triphenylmethane dye used worldwide as a fungicide and antiseptic in the aquaculture industry. Photolysis experiments were performed by direct exposure of a solution of MG in water to natural sunlight. The main transformation products (TPs) generated during the process were identified by liquid chromatography time-of-flight mass spectrometry (LC–TOF-MS) and gas chromatography mass spectrometry (GC–MS). The 28 TPs identified with this strategy indicate that MG undergoes three main reactions, N-demethylation, hydroxylation and cleavage of the conjugated structure forming benzophenone derivatives. These processes involve hydroxyl radical attack on the phenyl ring, the N,N-dimethylamine group and the central carbon atom. The Vibrio fischeri acute toxicity test showed that the solution remains toxic after MG has completely disappeared. This toxicity could be assigned, at least in part, to the formation of 4-(dimethylamine)benzophenone, which has an EC_50,30 min of 0.061 mg l⁻¹, and is considered “very toxic to aquatic organisms” by current EU legislation.     

Fast determination of phenoxy acid herbicides in carrots and apples using liquid chromatography coupled triple quadrupole mass spectrometry

A fast, simple and inexpensive method has been developed for the analysis of phenoxy acid herbicides: 2,4-dichlorophenoxyacetic acid (2,4-D), 4-chloro-2-methylphenoxyacetic acid (MCPA), 2-(4-chloro-o-tolyloxy)propionic acid (MCPP), 2-(4-aryloxyphenoxy)propionic acid (Fluazifop) and 2-(4-aryloxyphenoxy)propionic acid (Haloxyfop) in carrots and apples by liquid chromatography coupled to triple quadrupole mass spectrometry (LC/MS/MS). The compounds were analyzed by QuEChERS (quick, easy, cheap, effective, rugged, safe) methodology without cleanup.

The recoveries were performed at two spiked levels (0.05 and 0.5 mg/kg) for both matrices with six replicates for each level. The mean recoveries ranged from 70–92% for both apples and carrots. The precision of the method expressed as relative standard deviation (RSD%) was found to be in the range 3–15%. For all compounds, good linearity (r² > 0.99) was obtained over the range of concentration from 0.05 μ g/mL to 0.5 μ g/mL, corresponding to the pesticide concentrations of 0.05 mg/kg and 0.5 mg/kg, respectively. The determination limits (LOQs) ranged from 0.01 ng/mL to 1.3 ng/mL in solvent, whereas, the LOQs calculated in matrix ranged from 0.05 ng/g to 21.0 ng/g for apples and from 0.06 ng/g to 10.2 ng/g for carrots. The developed methodology combines the advantages of both QuEChERS and LC/MS/MS producing a very rapid, sensitive and cheap method useful for the routine analytical laboratories.     

Monoterpene emissions and carbonyl compound air concentrations during the blooming period of rape (Brassica napus)

An increasing percentage of agricultural land in Germany is used for oil seed plants. Hence, rape has become an important agricultural plant (in Saxony 1998: 12% of the farmland) in the recent years. During flowering of rape along with intensive radiation and high temperatures, a higher production and emission of biogenic VOC was observed. The emissions of terpenes were determined and more importantly, high concentrations of organic carbonyl compounds were observed during this field experiment. All measurements of interest have been carried out during two selected days with optimal weather conditions. It is found that the origin or the mechanism of formation of different group of compounds had strong influence on the day to day variation of their concentrations. The emission flux of terpenes from flowering rape plants was determined to be 16–32 μg h⁻¹ m⁻² (30–60 ng h⁻¹ per g dry plant––540–1080 ng h⁻¹ per plant), in total. Limonene, -thujene and sabinene were the most important compounds (about 60% of total terpenes). For limonene and sabinene reference emission rates (M_S) and temperature coefficients were determined: β_limonene=0.108 K⁻¹ and M_S=14.57 μg h⁻¹ m⁻²; β_sabinene=0.095 K⁻¹ and M_S=5.39 μg h⁻¹ m⁻².

The detected carbonyl compound concentrations were unexpectedly high (maximum formaldehyde concentration was 18.1 ppbv and 3.4 ppbv for butyraldehyde) for an open field. Possible reasons for these concentrations are the combination of primary emission from the plants induced by high temperature and high ozone stress, the secondary formation from biogenically and advected anthropogenically emitted VOC at high radiation intensities and furthered by the low wind speeds at this time.     

Determination of the toxic impurities 3,3′,4,4′-tetrachloroazobenzene and 3,3′,4,4′-tetrachloroazoxybenzent in commercial diuron, linuron and 3,4-dichloroaniline samples

Methods are described for the determination of 3,3′,4,4′-tetrachloroazobenzene (TCAB) and 3,3′,4,4′-tetrachloroazoxybenzene (TCAOB) in diuron and linuron formulations and in 3,4-dichloroaniline. The formulations were extracted with acetone, and after removal of solvent, the residue was partitioned between methanol-water and hexane. 3,4-Dichloroaniline products were partitioned between methanol-1M hydrochloric acid and hexane. The hexane extracts were purified by column chromatography on silica gel and analysed by gas chromatography with electron-capture detection. Detection limits for TCAB and TCAOB were around 0.1 ug/g using samples of one gram. Levels of 5.5 – 28 ug TCAB and 1.9 − < 0.05 ug TCAOB/g herbicide formulation and 2.4 – 460 ug TCAB/g TCAB/g 3,4-dichloroaniline have been found. TCAOB levels were below the detection limits in the 3,4-dichloroaniline samples. The presence of TCAB and TCAOB was confirmed by gas chromatography-mass spectrometry.