Light scattering characteristics of aerosols at ambient and as a function of relative humidity: Part II--A comparison of measured scattering and aerosol concentrations using statistical models

The eastern United States national parks experience some of the worst visibility conditions in the nation. To study these conditions, the Southeastern Aerosol and Visibility Study (SEAVS) was undertaken to characterize the size-dependent composition, thermodynamic properties, and optical characteristics of the ambient atmospheric particles. It is a cooperative three-year study that is sponsored by the National Park Service and the Electric Power Research Institute and its member utilities. The field portion of the study was carried out from July 15 to August 25, 1995. The study design, instrumental configuration, and estimation of aerosol types from particle measurements is presented in a companion paper. In the companion paper, we compare measurements of scattering at ambient conditions and as functions of relative humidity to theoretical predictions of scattering. In this paper, we make similar comparisons, but using statistical techniques. Statistically derived specific scattering associated with sulfates suggest that a reasonable estimate of sulfate scattering can be arrived at by assuming nominal dry specific scattering and treating the aerosols as an external mixture with ammoniation of sulfate accounted for and by the use of Tang's growth curves to predict water absorption. However, the regressions suggest that the sulfate scattering may be underestimated by about 10%. Regression coefficients on organics, to within the statistical uncertainty of the model, suggest that a reasonable estimate of organic scattering is about 4.0 m2/g. A new analysis technique is presented, which does not rely on comparing measured to model estimates of scattering to evoke an understanding of ambient aerosol growth properties, but rather relies on measurements of scattering as a function of relative humidity to develop actual estimates of f(RH) curves. The estimates of the study average f(RH) curve for sulfates compares favorably with the theoretical f(RH) curve for ammonium bisulfate, which is in turn consistent with the study average sulfate ammoniation corresponding to a molar ratio of NH4/SO4 of approximately one. The f(RH) curve for organics is not significantly different from one, suggesting that organics are weakly to nonhygroscopic.     

Aerosol light scattering measurements as a function of relative humidity

The hygroscopic nature of atmospheric fine aerosol was investigated at a rural site in the Great Smoky Mountains National Park during July and August 1995. Passing the sample aerosol through an inlet, which housed an array of Perma Pure diffusion dryers, controlled the sample aerosol's relative humidity (RH). After conditioning the aerosol sample in the inlet, the light scattering coefficient and the aerosol size distribution were simultaneously measured. During this study, the conditioned aerosol's humidity ranged between 5% < RH < 95%. Aerosol response curves were produced using the ratio bspw/bspd; where bspw is the scattering coefficient measured at some RH greater than 20% and bspd is the scattering coefficient of the "dry" aerosol. For this work, any sample RH values below 15% were considered dry. Results of this investigation showed that the light scattering ratio increased continuously and smoothly over the entire range of relative humidity. The magnitude of the ratio at a particular RH value, however, varied considerably in time, particularly for RH values greater than approximately 60%. Curves of the scattering coefficient ratios as a function of RH were generated for each day and compared to the average 12-hour chemical composition of the aerosol. This comparison showed that for any particular RH value the ratio was highest during time periods of high sulfate concentrations and lowest during time periods of high soil or high organic carbon concentrations.     

Light Scattering Characteristics of Aerosols at Ambient and as a Function of Relative Humidity: Part II—A Comparison of Measured Scattering and Aerosol Concentrations Using Statistical Models

ABSTRACT

The eastern United States national parks experience some of the worst visibility conditions in the nation. To study these conditions, the Southeastern Aerosol and Visibility Study (SEAVS) was undertaken to characterize the size-dependent composition, thermodynamic properties, and optical characteristics of the ambient atmospheric particles. It is a cooperative three-year study that is sponsored by the National Park Service and the Electric Power Research Institute and its member utilities. The field portion of the study was carried out from July 15 to August 25, 1995.

The study design, instrumental configuration, and estimation of aerosol types from particle measurements is presented in a companion paper. In the companion paper, we compare measurements of scattering at ambient conditions and as functions of relative humidity to theoretical predictions of scattering. In this paper, we make similar comparisons, but using statistical techniques. Statistically derived specific scattering associated with sulfates suggest that a reasonable estimate of sulfate scattering can be arrived at by assuming nominal dry specific scattering and treating the aerosols as an external mixture with ammoniation of sulfate accounted for and by the use of Tang's growth curves to predict water absorption. However, the regressions suggest that the sulfate scattering may be underestimated by about 10%. Regression coefficients on organics, to within the statistical uncertainty of the model, suggest that a reasonable estimate of organic scattering is about 4.0 m²/g.

A new analysis technique is presented, which does not rely on comparing measured to model estimates of scattering to evoke an understanding of ambient aerosol growth properties, but rather relies on measurements of scattering as a function of relative humidity to develop actual estimates of f(RH) curves. The estimates of the study average f(RH) curve for sulfates compares favorably with the theoretical f(RH) curve for ammonium bisulfate, which is in turn consistent with the study average sulfate am-moniation corresponding to a molar ratio of NH₄/SO₄ of approximately one. The f(RH) curve for organics is not significantly different from one, suggesting that organics are weakly to nonhygroscopic.     

Modeling the spectral optical properties of ammonium sulfate and biomass burning aerosols: parameterization of relative humidity effects and model results

The importance of including the global and regional radiative effects of aerosols in climate models has increasingly been realized. Accurate modeling of solar radiative forcing due to aerosols from anthropogenic sulfate and biomass burning emissions requires adequate spectral resolution and treatment of spatial and temporal variability. The variation of aerosol spectral optical properties with local relative humidity and dry aerosol composition must be considered. Because the cost of directly including Mie calculations within a climate model is prohibitive, parameterizations from off-line calculations must be used. Starting from a log-normal size distribution of dry ammonium sulfate, we developed optical properties for tropospheric sulfate aerosol at 15 relative humidities up to 99%. The resulting aerosol size distributions were then used to calculate bulk optical properties at wavelengths between 0.175 and 4 μm. Finally, functional fits of optical properties were made for each of 12 wavelength bands as a function of relative humidity. Significant variations in optical properties occurred across the total solar spectrum. Relative increases in specific extinction and asymmetry factor with increasing relative humidity became larger at longer wavelengths. Significant variation in single-scattering albedo was found only in the longest near-IR band. This is also the band with the lowest single scattering albedo. A similar treatment was done for aerosols from biomass burning. In this case, two size distributions were considered. One was based on a distribution measured for Northern Hemisphere temperate forest fires while the second was based on a measured size distribution for tropical fires. Equilibrium size distributions and compositions were calculated for 15 relative humidities and five black carbon fractions. Mie calculations and band averages of optical properties were done for each of the resulting 75 cases. Finally, fits were made for each of 12 spectral bands as functions of relative humidity and black carbon fraction. These optical properties result in global average forcing from anthropogenic sulfate aerosols of −0.81 Wm^-2. The global average forcing for biomass aerosols ranged from −0.23 to −0.25 Wm^-2 depending on the assumed size distribution, while fossil fuel organic and black carbon are estimated to heat the atmosphere by about 0.16 Wm^-2.     

Optical measurements of aerosol size distributions in Great Smoky Mountains National Park: dry aerosol characterization

Aerosol size distributions were measured during the summertime 1995 Southeastern Aerosol and Visibility Study (SEAVS) in Great Smoky Mountains National Park using an Active Scattering Aerosol Spectrometer (ASASP-X) optical particle counter. We present an overview of the experimental method, our data inversion technique, timelines of the size distribution parameters, and calculations of dry accumulation mode aerosol density and refractive index. Aerosol size distributions were recorded during daylight hours for aerosol in the size range 0.1 < Dp < 2.5 microns. The particle refractive index used for the data inversion was calculated with the partial molar refractive index approach using 12-hr measured aerosol chemical composition. Aerosol accumulation mode volume concentrations ranging from 1 to 26 micron 3 cm-3 were observed, with an average of 7 +/- 5 micron 3 cm-3. The study average dry accumulation mode geometric volume median diameter was 0.27 +/- 0.03 micron, and the mean geometric standard deviation was 1.45 +/- 0.06. Using an internally mixed aerosol model, and assuming chemical homogeneity across the measured particle distribution, an average accumulation mode dry sulfate ion mass scattering efficiency of 3.8 +/- 0.6 m2 g-1 was calculated.     

Estimates of particle hygroscopicity during the Southeastern Aerosol and Visibility Study

Aerosol water content was determined from relative humidity controlled optical particle counter (ASASP-X) size distribution measurements made during the Southeastern Aerosol and Visibility Study (SEAVS) in the Great Smoky Mountains National Park during summer 1995. Since the scattering response function of the ASASP-X is sensitive to particle refractive index, a technique for calibrating the ASASP-X for any real refractive index was developed. A new iterative process was employed to calculate water mass concentration and wet refractive index as functions of relative humidity. Experimental water mass concentrations were compared to theoretically predicted values assuming only ammonium sulfate compounds were hygroscopic. These comparisons agreed within experimental uncertainty. Estimates of particle hygroscopicity using a rural aerosol model of refractive index as a function of relative humidity demonstrated no significant differences from those made with daily varying refractive index estimates. Although aerosol size parameters were affected by the assumed chemical composition, forming ratios of these parameters nearly canceled these effects.     

Estimates of Particle Hygroscopicity during the Southeastern Aerosol and Visibility Study

ABSTRACT

Aerosol water content was determined from relative humidity controlled optical particle counter (ASASP-X) size distribution measurements made during the Southeastern Aerosol and Visibility Study (SEAVS) in the Great Smoky Mountains National Park during summer 1995. Since the scattering response function of the ASASP-X is sensitive to particle refractive index, a technique for calibrating the ASASP-X for any real refractive index was developed. A new iterative process was employed to calculate water mass concentration and wet refractive index as functions of relative humidity. Experimental water mass concentrations were compared to theoretically predicted values assuming only ammonium sulfate compounds were hygroscopic. These comparisons agreed within experimental uncertainty. Estimates of particle hygroscopicity using a rural aerosol model of refractive index as a function of relative humidity demonstrated no significant differences from those made with daily varying refractive index estimates. Although aerosol size parameters were affected by the assumed chemical composition, forming ratios of these parameters nearly canceled these effects.     

Size distribution and sources of aerosol in Launceston, Australia, during winter 1997

As part of a pilot study into the chemical and physical properties of Australian fine particles, a suite of aerosol samples was collected at Ti Tree Bend in Launceston, Tasmania, during June and July 1997. This period represents midwinter in the Southern Hemisphere, a period when aerosol sources in Launceston are dominated by smoke from domestic wood burning. This paper describes the results from this measurement campaign, with the aim of assessing the effect of wood smoke on the chemical and physical characteristics of ambient aerosol. A micro orifice uniform deposit impactor (MOUDI) was used to measure the size distributions of the aerosol from 0.05 to 20 microns aerodynamic diameter. Continuous measurements of fine particle mass were made using a PM2.5 tapered element oscillating microbalance (TEOM) and light scattering coefficients at 530 nm were measured with nephelometers. Mass size distributions tended to be bimodal, with the diameter of the dominant mode tending to smaller sizes with increases in total mass. Non-sea salt potassium and polycyclic aromatic hydrocarbons (PAHs) were used as chemical tracers for wood smoke. Wood smoke was found to increase absolute particle mass (enough to regularly exceed air quality standards), and to concentrate mass in a single mode below 1 micron aerodynamic diameter. The acid-base equilibrium of the aerosol was altered by the wood smoke source, with free acidity hydrogen ion, non-sea salt sulfate, and ammonium concentrations being higher and the concentration of all species, including nitrate (to differing extents), focused in the fine particle size ranges. The wood smoke source also heavily influenced the aerosol scattering efficiency, adding to a strong diurnal cycle in both mass concentration and light scattering.     

Analysis and simulation of wintertime light scattering by the urban aerosol in Dallas-Fort Worth

Wintertime atmospheric light scattering in Dallas, TX, was estimated through the use of aerosol models. Input data for the aerosol models were provided by measurements of aerosol chemistry, physical particle size distributions, and distributions of particulate sulfur by particle size, and by predictions by an atmospheric simulation model. Light scattering measurements provided a basis for testing the aerosol models. The SCAPE thermodynamic equilibrium model was used to estimate the amount of liquid water associated with particles and the ELSIE Mie scattering model was applied to estimate the resulting light scattering. The calculations were based on aerosol properties measured in Dallas during December 1994 and February 1995, and changes in scattering due to hypothetical changes in the aerosol were predicted. The predicted light scattering was compared to scattering measured by an Optec nephelometer; agreement was within 20% in every case.     

Light Scattering Characteristics of Aerosols as a Function of Relative Humidity: Part I—A Comparison of Measured Scattering and Aerosol Concentrations Using the Theoretical Models

ABSTRACT

The Southeastern Aerosol and Visibility Study (SEAVS) was undertaken to characterize the size-dependent composition, thermodynamic properties, and optical characteristics of the ambient atmospheric particles in the southeastern United States. The field portion of the study was carried out from July 15 to August 25, 1995.

As part of the study a relative humidity controlled inlet was built to raise or lower the relative humidity to predetermined levels before the aerosol was passed into an integrating nephelometer or particle-sizing device. Five other integrating nephelometers were operated in various configurations, two of which were fitted with a 2.5 μm inlet. Fine particle (<2.5 μm) samplers were operated to measure concentrations of sulfate, nitrate, and ammonium ions, organic and elemental carbon, and fine soil. Mass size distributions were measured with an eight-stage, single orifice cascade impactor.     

Evaluation of the IMPROVE Equation for estimating aerosol light extinction

The [revised] IMPROVE Equation for estimating light extinction from aerosol chemical composition was evaluated considering new measurements at U.S. national parks. Compared with light scattering (Bsp) measured at seven IMPROVE sites with nephelometer data from 2003–2012, the [revised] IMPROVE Equation over- and underestimated Bsp in the lower and upper quintiles, respectively, of measured Bsp. Underestimation of the worst visibility cases (upper quintile) was reduced by assuming an organic mass (OM)/organic carbon (OC) ratio of 2.1 and hygroscopic growth of OM, based on results from previous field studies. This assumption, however, tended to overestimate low Bsp even more. Assuming that sulfate was present as ammonium bisulfate rather than as ammonium sulfate uniformly reduced estimated Bsp. The split-mode model of concentration- and size-dependent dry mass scattering efficiencies in the [revised] IMPROVE Equation does not eliminate systematic biases in estimated Bsp. While the new measurements of OM/OC and OM hygroscopicity should be incorporated into future iterations of the IMPROVE Equation, the problem is not well constrained due to a lack of routine measurements of sulfate neutralization and the water-soluble fraction of OM in the IMPROVE network.

Implications: Studies in U.S. national parks showed that aerosol organics contain more mass and absorb more water as a function of relative humidity than is currently assumed by the IMPROVE Equation for calculating chemical light extinction. Consideration of these results could significantly shift the apportionment of light extinction to water-soluble organic aerosols and therefore better inform pollution control strategies under the U.S. Environmental Protection Agency Regional Haze Rule.     

Aerosol light-scattering in The Netherlands

The relation between the (midday) aerosol light-scattering and the concentrations of nitrate and sulfate has been assessed at a site near the coast of the North Sea in The Netherlands. Midday was selected for the measurements because this is the time at which the aerosol is most effective in the scattering of solar radiation. Automated thermodenuders were used for the hourly measurement of the concentration of nitrate and sulfate with a lower detection limit of 0.1 μ m⁻³. The site is operational since October 1993. The first-year average dry aerosol light-scattering (measured with an integrating nephelometer at a wavelength of 525 nm) was 0.71 × 10⁻⁴ m^1&#x0304;. In arctic marine air the aerosol light-scattering was a factor of 10 lower than the average value, in polluted continental air it was up to a factor of 10 higher. The ratio of the total aerosol light-scattering to the concentration of sulfate was 20 m² g⁻¹. The contribution of nitrate to the aerosol light-scattering was higher than that of sulfate in the winter and of about equal magnitude in the summer period. In November and December of 1993, the humidity dependence of the aerosol light-scattering was investigated. Two types of (continental) aerosol were found with respect to the humidity behavior. One type showed a significant increase in light-scattering at the deliquescence points of ammonium nitrate and ammonium sulfate, with that of ammonium nitrate the most pronounced. The second type of continental aerosol did not show deliquescence, but followed the typical humidity dependence of aerosol in a supersaturated droplet state. In this latter aerosol type, nitrate dominated over sulfate. It was concluded from the study that the aerosol light-scattering in The Netherlands, in particular its humidity dependence, is governed by (ammonium) nitrate.     

Seasonal Variations in Aerosol Composition and Acidity at Shenandoah and Great Smoky Mountains National Parks

The concentration of elements Na through Pb, select ions, and organic carbon from fine (<2.5 µm) particles has been monitored at Shenandoah and Great Smoky Mountains National Parks from 1988 through 1995. The data obtained from 1988 through 1994 show that significant changes in the concentrations of many aerosol constituents occur on a seasonal basis. Particulate sulfate and organic carbon are shown to exhibit substantially higher concentrations during the summer, while sulfur dioxide and nitrate concentrations are highest during the winter.

A method for estimating the degree of neutralization of particulate sulfate is given. This method uses routinely measured aerosol elemental compositions because ammonium ion, the primary neutralizing species for sulfate, is not measured on a routine basis. Application of this method to the selected data set shows that sulfate aerosol is most acidic during summer with an average molar H_s (moles of hydrogen associated with sulfur) to S (moles of sulfur) ratio of approximately 4. This suggests the average sulfate particle during the summer has a molar coon slightly more acidic than ammonium bisulfate (NH₄HSO₄) which has a molar hydrogen to sulfur ratio of 5. Winter H_s to S ratios, however, are approximately 8, suggesting the aerosol is on average fully neutralized ammonium sulfate [(NH₄)₂SO₄].     

The effect of water on gas–particle partitioning of secondary organic aerosol. Part I: α-pinene/ozone system

The effect of relative humidity (RH) on aerosol formation by the semi-volatile oxidation products of the α-pinene/O₃ system has been comprehensively studied. Experiments were performed in the presence of ammonium sulfate (aqueous, dry), ammonium bisulfate seed (aqueous, dry), and aqueous calcium chloride seed aerosols to ascertain their effect on the partitioning of the oxidation products. The yield of organic aerosol varies little with RH, and is not affected by the presence of dry inorganic salt aerosols. Aqueous salt aerosols reduce the yield of organic aerosol compared to that under seed-free or dry seed conditions. The degree of reduction is electrolyte dependent, with aqueous ammonium sulfate leading to the largest reduction and aqueous calcium chloride the smallest. Hygroscopic growth of the organic aerosol from <2% to 85% RH was also monitored, and could be satisfactorily represented as the sum of the individual contributions of the organic and inorganic fractions. The implications of the growth factor measurements for concentration/activity relationships of the condensed phase organic material (assuming a liquid solution) was explored. The formation of the organic aerosol was investigated using a simple two component model, and also one including the 12 product compounds identified in a previous study. The experimental results for <2% and 50% RH (without salt seed aerosols) could be satisfactorily predicted. However, the aqueous salt seed aerosols are predicted to increase the overall yield due to the dissolution of the organic compounds into the water associated with the seed aerosol—the opposite effect to that observed. The implications of two distinct phases existing the aerosol phase were investigated.     

Simultaneous measurement of light-scattering properties and particle size distribution for aerosols: Application to ammonium sulfate and quartz aerosol particles

An apparatus for measuring the scattering phase function and linear polarization of aerosol particles has been developed. The apparatus uses an elliptical mirror and CCD camera to image the full angular scattering range simultaneously. An in-line aerodynamic particle sizer (APS) in the particle flow stream provides for the simultaneous measurement of the aerosol particle size distribution. This apparatus allows for a comparison of measured optical properties with theoretical model calculations based on the measured aerosol size distribution. The system was calibrated and tested using monodisperse polystyrene latex (PSL) spheres and with ammonium sulfate (AS) aerosol. We have also used the apparatus for measuring the scattering phase function and linear polarization for light scattering from irregular quartz aerosol particles. Our results show that Mie theory substantially overestimates the backscattering cross-section for quartz particles in the size parameter range X∼2–4, in agreement with previous experimental work and theoretical modeling studies. We also present a normalized synthetic phase function for quartz dust aerosol in the accumulation mode size range (0.1–2.0 μm).     

Analysis and Simulation of Wintertime Light Scattering by the Urban Aerosol in Dallas-Fort Worth

ABSTRACT

Wintertime atmospheric light scattering in Dallas, TX, was estimated through the use of aerosol models. Input data for the aerosol models were provided by measurements of aerosol chemistry, physical particle size distributions, and distributions of particulate sulfur by particle size, and by predictions by an atmospheric simulation model. Light scattering measurements provided a basis for testing the aerosol models. The SCAPE thermodynamic equilibrium model was used to estimate the amount of liquid water associated with particles and the ELSIE Mie scattering model was applied to estimate the resulting light scattering. The calculations were based on aerosol properties measured in Dallas during December 1994 and February 1995, and changes in scattering due to hypothetical changes in the aerosol were predicted. The predicted light scattering was compared to scattering measured by an Optec nephelom-eter; agreement was within 20% in every case.     

Optical Measurements of Aerosol Size Distributions in Great Smoky Mountains National Park: Dry Aerosol Characterization

ABSTRACT

Aerosol size distributions were measured during the summertime 1995 Southeastern Aerosol and Visibility Study (SEAVS) in Great Smoky Mountains National Park using an Active Scattering Aerosol Spectrometer (ASASP-X) optical particle counter. We present an overview of the experimental method, our data inversion technique, timelines of the size distribution parameters, and calculations of dry accumulation mode aerosol density and refractive index. Aerosol size distributions were recorded during daylight hours for aerosol in the size range 0.1 < Dp < 2.5 u,m. The particle refractive index used for the data inversion was calculated with the partial molar refractive index approach using 12-hr measured aerosol chemical composition. Aerosol accumulation mode volume concentrations ranging from 1 to 26 u,m³ cm^-3 were observed, with an average of 7 ± 5 u,m³ cm^-3. The study average dry accumulation mode geometric volume median diameter was 0.27 ± 0.03 u,m, and the mean geometric standard deviation was 1.45 ± 0.06. Using an internally mixed aerosol model, and assuming chemical homogeneity across the measured particle distribution, an average accumulation mode dry sulfate ion mass scattering efficiency of 3.8 ± 0.6 m² g^-1 was calculated.     

Optical properties of the San Joaquin Valley aerosol collected during the 1995 integrated monitoring study

Optical, filter chemistry, and cascade impactor data collected during the winter intensive of the IMS95 Study in the San Joaquin Valley (SJV) of California were analyzed to determine the light-extinction efficiency of aerosol species. Regression of light scattering by particles (b_sp) measured by a heated nephelometer without a size selective inlet against PM_2.5 front filter mass gave a scattering efficiency of 3.67±0.05 m²/g with an R² (fraction of variance explained) of 0.94. Division of the aerosol into two components and applying two different corrections to the filter data for nitrate and organic carbon on the backup filter gave scattering efficiencies of 3.7±0.3 or 4.1±0.2 m²/g for the salts composed of sulfate, nitrate, and ammonium and 2.9±0.2 or 3.1±0.2 m²/g for all other species with R² of 0.985 and 0.986. The ambient b_sp measured by an open nephelometer was a simple function of PM_2.5 mass and relative humidity (RH), giving R² of 0.90 and 0.88 for two different RH sensors. Variations in PM_2.5 size distribution and composition did not have an important effect on ambient b_sp. The RH data from each sensor were repeatable enough to show the existence of a simple dependence of aerosol water uptake on RH, but RH sensor calibration uncertainties prevented determining this dependence. Inversion of MOUDI cascade impactor data gave sulfate and nitrate mass median diameters (MMD) between 0.4 and 0.8 μm. Mie scattering calculations based on MOUDI data provided humidity-dependent extinction efficiencies for the principal aerosol chemical species. These efficiencies combined with particle filter data showed that ammonium nitrate was the dominant contributor to wintertime light extinction. Source apportionment showed that light extinction was dominated by emissions sources contributing to the formation of secondary species, especially nitrate. These wintertime data are not expected to apply to summertime in the SJV.     

Variation of mass scattering efficiencies in IMPROVE

The Interagency Monitoring of Protected Visual Environments (IMPROVE) equation used to assess compliance under the U.S. Environmental Protection Agency (EPA) Haze Rule assumes that dry mass scattering efficiencies for aerosol chemical components are constant. However, examination of aerosol size distributions and chemical composition during the Big Bend Regional Aerosol and Visibility Observational Study and the Southeastern Aerosol and Visibility Study suggests that volume and mass scattering efficiencies vary directly with increasing particle light scattering and aerosol mass concentration. This is consistent with the observation that particle distributions were shifted to larger sizes under more polluted conditions and appears to be related to aging of the aerosol during transport to remote locations.     

Size Distribution and Sources of Aerosol in Launceston,Australia, during Winter 1997

ABSTRACT

As part of a pilot study into the chemical and physical properties of Australian fine particles, a suite of aerosol samples was collected at Ti Tree Bend in Launceston, Tasmania, during June and July 1997. This period represents midwinter in the Southern Hemisphere, a period when aerosol sources in Launceston are dominated by smoke from domestic wood burning. This paper describes the results from this measurement campaign, with the aim of assessing the effect of wood smoke on the chemical and physical characteristics of ambient aerosol. A micro orifice uniform deposit impactor (MOUDI) was used to measure the size distributions of the aerosol from 0.05 to 20 n m aerodynamic diameter. Continuous measurements of fine particle mass were made using a PM_2.5 tapered element oscillating microbalance (TEOM) and light scattering coefficients at 530 nm were measured with nephelometers.

Mass size distributions tended to be bimodal, with the diameter of the dominant mode tending to smaller sizes with increases in total mass. Non-sea salt potassium and polycyclic aromatic hydrocarbons (PAHs) were used as chemical tracers for wood smoke. Wood smoke was found to increase absolute particle mass (enough to regularly exceed air quality standards), and to concentrate mass in a single mode below 1 μm aerodynamic diameter. The acid-base equilibrium of the aerosol was altered by the wood smoke source, with free acidity hydrogen ion, non-sea salt sulfate, and ammonium concentrations being higher and the concentration of all species, including nitrate (to differing extents), focused in the fine particle size ranges. The wood smoke source also heavily influenced the aerosol scattering efficiency, adding to a strong diurnal cycle in both mass concentration and light scattering.