Removal of heavy metals and arsenic from a co-contaminated soil by sieving combined with washing process

Batch experiments were conducted with a heavy metals and arsenic co-contaminated soil from an abandoned mine to evaluate the feasibility of a remediation technology that combines sieving with soil washing.Leaching of the arsenic and heavy metals from the different particle size fractions was found to decrease in the order: 0.1,2–0.1,and 2 mm.With increased contact time,the concentration of heavy metals in the leachate was significantly decreased for small particles,probably because of adsorption by the clay soil component.For the different particle sizes,the removal efficiencies for Pb and Cd were75%–87%,and 61%–77% for Zn and Cu,although the extent of removal was decreased for As and Cr at 45%.The highest efficiency by washing for Pb,Cd,Zn,and As was from the soil particles 2 mm,although good metal removal efficiencies were also achieved in the small particle size fractions.Through SEM-EDS observations and correlation analysis,the leaching regularity of the heavy metals and arsenic was found to be closely related to Fe,Mn,and Ca contents of the soil fractions.The remediation of heavy metal-contaminated soil by sieving combined with soil washing was proven to be efficient,and practical remediation parameters were also recommended.     

Influence of zeta potential on the flocculation of cyanobacteria cells using chitosan modified soil

Using chitosan modified soil to flocculate and sediment algal cells has been considered as a promising strategy to combat cyanobacteria blooms in natural waters. However, the flocculation efficiency often varies with algal cells with different zeta potential (ZP) attributed to different growth phases or water conditions. This article investigated the relationship between ZP of Microcystis aeruginosa and its influence to the flocculation efficiency using chitosan modified soil. Results suggested that the optimal removal efficiency was obtained when the ZP was between − 20.7 and − 6.7 mV with a removal efficiency of more than 80% in 30 min and large floc size of > 350 μm. When the algal cells were more negatively charged than − 20.7 mV, the effect of chitosan modified soil was depressed (< 60%) due to the insufficient charge density of chitosan to neutralize and destabilize the algal suspension. When the algal cells were less negative than − 6.7 mV or even positively charged, a small floc size (< 120 μm) was formed, which may be difficult to sink under natural water conditions. Therefore, manipulation of ZP provided a viable tool to improve the flocculation efficiency of chitosan modified soil and an important guidance for practical engineering of cyanobacteria bloom control.     

芘在土壤不同粒径组分中的形态分布

以芘为PAHs代表物,采用土壤粒径分级和PAHs连续提取方法,研究了老化4周污染黄棕壤中芘在不同粒径组分中的形态分布.结果表明,供试土壤中芘主要以有机溶剂提取态和可脱附态存在,结合态残留量所占比例甚小;细砂粒、粉粒、粗黏粒和细黏粒中芘残留占原土总残留的比例分别为6.00%、4.66%、34.68%和40.88%.各粒径组分中各形态芘含量大小顺序为有机溶剂提取态>可脱附态>结合态,有机溶剂提取态和可脱附态是各粒径组分中芘残留的主要存在形态(占比98.82%以上),芘结合态残留量占比<1.18%.土壤中黏粒(包括细黏粒和粗黏粒)是芘可脱附态、有机溶剂提取态、结合态和可提取态残留储存的主要粒径组分.     

滇池典型湖区沉积物粒径与重金属分布特征

对滇池3个代表性湖区(草海、湖心区、外海南部)表层(0~10cm)沉积物的粒径组成进行了分析,测试了不同粒径沉积物的主要理化性质和Cu、Cr、Ni、Zn、Pb、Fe、Mn、Cd等8种重金属的质量分数,并对滇池沉积物中重金属质量分数的粒径效应作了校正. 结果表明:滇池表层沉积物粒径主要分布在<250μm的范围内;粉砂(4~<63μm)所占比例最大,平均达到60%;黏土(<4μm)次之,平均占19%. 随着粒径的减小,大部分重金属质量分数在不同粒径的沉积物中呈增加趋势. 重金属在细粒径(<63μm) 沉积物中所占比例平均达79%,显著高于其他粒径(63~<125、125~<250μm). Cr、Cd、Cu、Pb、Zn和Ni具有相似的富集特性,其质量分数高值均出现在粒径为4~<63μm的沉积物中,该粒径沉积物中6种重金属的质量分数分别为土壤背景值的2.04、9.77、4.35、5.11、3.47和4.60倍;而w(Fe)和w(Mn)在各粒径沉积物中无明显差异. 黏土校正结果与不同粒径沉积物黏土校正的理论计算值相差不大. 黏土校正与参比元素校正都适合校正滇池不同粒径沉积物的重金属质量分数.      

Particle size distribution and characteristics of heavy metals in road-deposited sediments from Beijing Olympic Park

Due to rapid urbanization and industrialization, heavy metals in road-deposited sediments (RDSs) of parks are emitted into the terrestrial, atmospheric, and water environment, and have a severe impact on residents' and tourists' health. To identify the distribution and characteristic of heavy metals in RDS and to assess the road environmental quality in Chinese parks, samples were collected from Beijing Olympic Park in the present study. The results indicated that particles with small grain size (< 150 μm) were the dominant fraction. The length of dry period was one of the main factors affecting the particle size distribution, as indicated by the variation of size fraction with the increase of dry days. The amount of heavy metal (i.e., Cu, Zn, Pb and Cd) content was the largest in particles with small size (< 150 μm) among all samples. Specifically, the percentage of Cu, Zn, Pb and Cd in these particles was 74.7%, 55.5%, 56.6% and 71.3%, respectively. Heavy metals adsorbed in sediments may mainly be contributed by road traffic emissions. The contamination levels of Pb and Cd were higher than Cu and Zn on the basis of the mean heavy metal contents. Specifically, the geoaccumulation index (I_geo) decreased in the order: Cd > Pb > Cu > Zn. This study analyzed the mobility of heavy metals in sediments using partial sequential extraction with the Tessier procedure. The results revealed that the apparent mobility and potential metal bioavailability of heavy metals in the sediments, based on the exchangeable and carbonate fractions, decreased in the order: Cd > Zn ≈ Pb > Cu.     

Drinking water treatment using a submerged internal-circulation membrane coagulation reactor coupled with permanganate oxidation

A submerged internal circulating membrane coagulation reactor(MCR) was used to treat surface water to produce drinking water. Polyaluminum chloride(PACl) was used as coagulant,and a hydrophilic polyvinylidene fluoride(PVDF) submerged hollow fiber microfiltration membrane was employed. The influences of trans-membrane pressure(TMP), zeta potential(ZP) of the suspended particles in raw water, and KMnO_4 dosing on water flux and the removal of turbidity and organic matter were systematically investigated. Continuous bench-scale experiments showed that the permeate quality of the MCR satisfied the requirement for a centralized water supply, according to the Standards for Drinking Water Quality of China(GB 5749-2006), as evaluated by turbidity(1 NTU) and total organic carbon(TOC)(5 mg/L)measurements. Besides water flux, the removal of turbidity, TOC and dissolved organic carbon(DOC) in the raw water also increased with increasing TMP in the range of 0.01–0.05 MPa. High ZP induced by PACl, such as 5–9 mV, led to an increase in the number of fine and total particles in the MCR, and consequently caused serious membrane fouling and high permeate turbidity.However, the removal of TOC and DOC increased with increasing ZP. A slightly positive ZP, such as 1–2 mV, corresponding to charge neutralization coagulation, was favorable for membrane fouling control. Moreover, dosing with KMnO_4 could further improve the removal of turbidity and DOC, thereby mitigating membrane fouling. The results are helpful for the application of the MCR in producing drinking water and also beneficial to the research and application of other coagulation and membrane separation hybrid processes.     

SDBS/Na+对红壤胶体悬液稳定性的影响

土壤中普遍存在的有机污染物和无机离子与土壤胶体颗粒的相互作用深刻地影响着土壤中一系列物理、化学和生物学过程.选取红壤胶体作为对象,利用动态光散射技术研究了不同浓度十二烷基苯磺酸钠(SDBS)和Na+作用下红壤胶体颗粒的凝聚过程,并结合体系的pH和Zeta电位分析了SDBS/Na+与土壤胶体颗粒相互作用的机制.结果表明:①相同浓度Na+作用下,随着SDBS浓度的升高,土壤胶体悬液稳定性增强.例如120 mmol·L-1Na+作用下,随着SDBS浓度从0 mmol·L-1升高到10 mmol·L-1,凝聚体有效粒径从702 nm下降至193 nm,总体平均凝聚速率从28.6 nm·min-1减小到3.36 nm·min-1;②相同浓度SDBS作用下,随着Na+浓度的升高,体系Zeta电位绝对值显著降低,凝聚体有效粒径逐渐增大,凝聚速率逐渐加快;③仅SDBS作用下,随着SDBS浓度的升高,体系Zeta电位绝对值从47.6 mV增加到62.2 mV,体系pH从6.17升高到6.76,但均小于土壤胶体悬液本身的pH(6.89).因此,SDBS通过疏水作用和静电作用吸附于土壤胶体颗粒表面,增加了颗粒表面的负电荷数量,降低了作用于胶体颗粒表面的有效Na+浓度(SDBS疏水长链的空间阻碍和高浓度SDBS所形成的胶束结构对Na+的吸附),使得胶体悬液稳定性增强,需要添加更多的Na+才能发生凝聚.     

Responses of soil ammonia oxidizers to a short-term severe mercury stress

The responses of soil ammonia-oxidizing archaea(AOA) and ammonia-oxidizing bacteria(AOB) to mercury(Hg) stress were investigated through a short-term incubation experiment.Treated with four different concentrations of Hg(CK,Hg25,Hg50,and Hg100,denoting 0,25,50,and 100 mg Hg/kg dry soil,respectively),samples were harvested after 3,7,and 28 day incubation.Results showed that the soil potential nitrification rate(PNR) was significantly inhibited by Hg stress during the incubation.However,lower abundances of AOA(the highest in CK: 9.20 × 10~7 copies/g dry soil; the lowest in Hg50: 2.68 × 10~7 copies/g dry soil) and AOB(the highest in CK: 2.68 × 10~7 copies/g dry soil; the lowest in Hg50:7.49 × 10~6 copies/g dry soil) were observed only at day 28 of incubation(P 0.05).Moreover,only the community structure of soil AOB obviously shifted under Hg stress as seen through DGGE profiles,which revealed that 2–3 distinct AOB bands emerged in the Hg treatments at day 28.In summary,soil PNR might be a very useful parameter to assess acute Hg stress on soil ecosystems,and the community structure of soil AOB might be a realistic biological indicator for the assessment of heavy metal stress on soil ecosystems in the future.     

Microbial and size characterization of airborne particulate matter collected on sticky tapes along US–Mexico border

Particulate matter(PM) emissions from various sources can affect significantly human health and environmental quality especially in the Chihuahuan Desert region along US–Mexico border. The objective of this study was to use the low-cost sticky tape method to collect airborne PM for size characterization and identification of fungal spores. Sticky tape samplers were placed at 1.0 and 2.0 m above the ground surface at experimental sites in Ciudad Juárez, Mexico and at 0.6, 1.2 and 1.8 m at New Mexico sites, USA. Soil samples were collected in both countries to determine fungal diversity, texture and moisture content Dust particles collected from all of the experimental sites had a dominant texture of clay( 0.002 mm). The dominant textures identified from soil samples collected from the US and Mexican sites were loam and sandy clay loam, respectively. Alternaria, Penicillium and Fusarium were frequently found funguses in the US sites while Alternaria and Aspergillus were commonly observed in the Mexican sites. The sticky tapes also showed a similar diversity of fungal microorganisms present in the airborne PM at both Mexico and US sites Alternaria, Penicillium and Aspergillus were the three groups of airborne fungal microorganisms consistently present in the US and Mexican sites. The low-cost sticky tape method has the potential to be used for characterizing different airborne microorganisms and dust particles.     

Effects of elevated atmospheric CO2 concentration and temperature on the soil profile methane distribution and diffusion in rice–wheat rotation system

The aim of this experiment was to determine the impacts of climate change on soil profile concentrations and diffusion effluxes of methane in a rice–wheat annual rotation ecosystem in Southeastern China. We initiated a field experiment with four treatments: ambient conditions (CKs), CO₂ concentration elevated to ~ 500 μmol/mol (FACE), temperature elevated by ca. 2°C (T) and combined elevation of CO₂ concentration and temperature (FACE + T). A multilevel sampling probe was designed to collect the soil gas at four different depths, namely, 7 cm, 15 cm, 30 cm and 50 cm. Methane concentrations were higher during the rice season and decreased with depth, while lower during the wheat season and increased with depth. Compared to CK, mean methane concentration was increased by 42%, 57% and 71% under the FACE, FACE + T and T treatments, respectively, at the 7 cm depth during the rice season (p < 0.05). Mean methane diffusion effluxes to the 7 cm depth were positive in the rice season and negative in the wheat season, resulting in the paddy field being a source and weak sink, respectively. Moreover, mean methane diffusion effluxes in the rice season were 0.94, 1.19 and 1.42 mg C/(m²·hr) in the FACE, FACE + T and T treatments, respectively, being clearly higher than that in the CK. The results indicated that elevated atmospheric CO₂ concentration and temperature could significantly increase soil profile methane concentrations and their effluxes from a rice–wheat field annual rotation ecosystem (p < 0.05).     

Distribution of chlorpyrifos in rice paddy environment and its potential dietary risk

Chlorpyrifos is one of the most extensively used insecticides in China. The distribution and residues of chlorpyrifos in a paddy environment were characterized under field and laboratory conditions. The half-lives of chlorpyrifos in the two conditions were 0.9–3.8 days (field) and 2.8–10.3 days (laboratory), respectively. The initial distribution of chlorpyrifos followed the increasing order of water < straw < soil, and soil was characterized as the major absorber. The ultimate residues in rice grain were below the maximum residue limit (MRL) with a harvest interval of 14 days. The chronic exposure for chlorpyrifos was rather low compared to the acceptable daily intake (ADI = 0.01 mg/kg bw) due to rice consumption. The chronic exposure risk from chlorpyrifos in rice grain was 5.90% and 1.30% ADI from field and laboratory results respectively. Concerning the acute dietary exposure, intake estimated for the highest chlorpyrifos level did not exceed the acute reference dose (ARfD = 0.1 mg/kg bw). The estimated short-term intakes (ESTIs) were 0.78% and 0.25% of the ARfD for chlorpyrifos. The results showed that the use of chlorpyrifos in rice paddies was fairly safe for consumption of rice grain by consumers.     

Aerosol-soil fractionation for Namib Desert samples

Four soil samples, collected in the central Namib Desert, were fractionated by dry sieving and aerosol generation into 16 size fractions in the range 0.15–300 μm diameter. The mass-size function of each soil and the dust (mineral aerosol) generated from the soil were studied. Due to the preferential lifting of smaller soil particles by the air stream, the soil underwent strong physical fractionation resulting in the bulk of the dust being found in the range of 1.3–10.3 μm, whereas the bulk of the soil was found in the range 63–300 μm. The concentrations of 11 elements in eight soil size fractions (from <45 to >300 μm) obtained by dry sieving were measured by X-ray fluorescence analysis while the concentration for these elements in eight size ranges (from <0.15 to >10.3 μm) obtained by aerosol generation were determined by particle-induced X-ray emission. The concentrations of the elements Al, Si, K, Rb and Sr were found to vary by less than a factor of two throughout the particle size range studied. However, the concentration of the elements Ca, Ti, Mn, Fe, Y and Zr increased when the particle size decreased below 150 μm to reach a maximum around 63-45 μm and then to decrease. The concentrations of the elements in the generated aerosol particles were found to be more similar to those in the bulk soil than any particular size fraction. For the aerosol size fraction, elemental enrichment factors were calculated with respect to the composition of average crustal rock, average soil, the bulk Namib soil and the small size fraction of the Namib soil. For several elements, the enrichment factors varied quite significantly, depending on the choice of the reference material. The elemental ratios in the mineral aerosol were also compared to those in the atmospheric aerosol from the Namib Desert. It was confirmed that there is a marine contribution for S, Cl and Sr in the Namib natural aerosol. The composition of the mineral aerosol generated in this study should be useful in source apportionment studies for the Namib Desert and sorrounding regions.     

Mechanism of Methylene Blue adsorption on hybrid laponite-multi-walled carbon nanotube particles

The kinetics of adsorption and parameters of equilibrium adsorption of Methylene Blue(MB)on hybrid laponite-multi-walled carbon nanotube(NT)particles in aqueous suspensions were determined.The laponite platelets were used in order to facilitate disaggregation of NTs in aqueous suspensions and enhance the adsorption capacity of hybrid particles for MB.Experiments were performed at room temperature(298 K),and the laponite/NT ratio(X_l)was varied in the range of 0–0.5.For elucidation of the mechanism of MB adsorption on hybrid particles,the electrical conductivity of the system as well as the electrokinetic potential of laponite-NT hybrid particles were measured.Three different stages in the kinetics of adsorption of MB on the surface of NTs or hybrid laponite-NT particles were discovered to be a fast initial stage Ⅰ(adsorption time t=0–10 min),a slower intermediate stage Ⅱ(up to t=120 min)and a long-lasting final stage Ⅲ(up to t=24 hr).The presence of these stages was explained accounting for different types of interactions between MB and adsorbent particles,as well as for the changes in the structure of aggregates of NT particles and the long-range processes of restructuring of laponite platelets on the surface of NTs.The analysis of experimental data on specific surface area versus the value of X_l evidenced in favor of the model with linear contacts between rigid laponite platelets and NTs.It was also concluded that electrostatic interactions control the first stage of adsorption at low MB concentrations.     

Pollution levels and characteristics of phthalate esters in indoor air of offices

The pollution status and characteristics of PAEs (phthalate esters) were investigated in indoor air of offices, and PAEs of both gas-phase and particulate-phase were detected in all the samples. The concentration (sum of the gas phase and the particulate phase) was 4748.24 ng/m³, ranging between 3070.09 and 6700.14 ng/m³. Diethyl phthalate, dibutyl phthalate, and di(2-ethylhexyl) phthalate were the most abundant compounds, together accounting for 70% of the ∑ 6PAEs. Dividing the particulate-phase PAEs into four size ranges (< 2.5, 2.5–5, 5–10, > 10 μm), the result indicated that PAEs in PM_2.5 were the most abundant, with the proportion of 72.64%. In addition, the PAE concentration in PM_2.5 correlated significantly with the total particulate-phase PAEs (R² = 0.85). Thus, the amount of PAEs in PM_2.5 can be estimated from the total amount of particulate-phase PAEs using this proportion. In a comparison between the offices and a newly decorated study room, it was found that pollution characteristics were similar between these two places. Thus, it is implied that the PAE concentration decreased by 50% 2 yr after decorating.     

Removal of Cs from water and soil by ammonium-pillared montmorillonite/Fe3O4 composite

To remove cesium ions from water and soil, a novel adsorbent was synthesized by following a one-step co-precipitation method and using non-toxic raw materials. By combining ammonium-pillared montmorillonite (MMT) and magnetic nanoparticles (Fe₃O₄), an MMT/Fe₃O₄ composite was prepared and characterized. The adsorbent exhibited high selectivity of Cs⁺ and could be rapidly separated from the mixed solution under an external magnetic field. Above all, the adsorbent had high removal efficiency in cesium-contaminated samples (water and soil) and also showed good recycling performance, indicating that the MMT/Fe₃O₄ composite could be widely applied to the remediation of cesium-contaminated environments. It was observed that the pH, solid/liquid ratio and initial concentration affected adsorption capacity. In the presence of coexisting ions, the adsorption capacity decreased in the order of Ca^2 + > Mg^2 + > K⁺ > Na⁺, which is consistent with our theoretical prediction. The adsorption behavior of this new adsorbent could be expressed by the pseudo-second-order model and Freundlich isotherm. In addition, the adsorption mechanism of Cs⁺ was NH₄⁺ ion exchange and surface hydroxyl group coordination, with the former being more predominant.     

Comparison of two methods for detection of fecal indicator bacteria used in water quality monitoring of the Three Gorges Reservoir

Scientifically sound methods to rapidly measure fecal indicator bacteria are important to ensure safe water for drinking and recreational purposes.A total of 200 water samples obtained from the Three Gorges Reservoir during three successive one-year study periods(October 2009 to September 2012) were analyzed using multiple-tube fermentation(MTF)and most probable numbers combined with polymerase chain reaction(MPN–PCR).The MPN–PCR method was found to be significantly more sensitive than the MTF method for detecting Escherichia coli and Enterococcus spp.,and of equal sensitivity for detecting total coliforms when all surface water samples were grouped together.The two analytical methods had a strong,significant relationship,but MPN–PCR took only 12–18 hr,compared with the 3–8 days needed using the MTF method.Bacterial concentrations varied per sampling site but were significantly lower in the mainstream of the Yangtze River than those in the backwater areas of tributaries.The water quality of 85.8% of water samples from the mainstream was suitable for use as a centralized potable water source,while the water quality of 52.5% of water samples from the backwater areas was unsuitable for recreational activities.Relationships between fecal indicator bacteria showed significant correlation(r = 0.636–0.909,p 0.01,n = 200),while a weak but significant correlation was found between fecal indicators and water turbidity,water temperature,daily inflow,and total dissolved solids(r = 0.237–0.532,p 0.05,n = 200).The study indicated that MPN–PCR is a rapid and easily performed deoxyribonucleic acid(DNA)-based method for quantitative detection of viable total coliforms,E.coli,and Enterococcus spp.in surface water.     

Occurrence and impact of polychlorinated dibenzo-p-dioxins/dibenzofurans in the air and soil around a municipal solid waste incinerator

To assess the influence of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans(PCDD/Fs) on the environment in the vicinity of municipal solid waste incinerators(MSWIs), we determined the levels of PCDD/Fs in air and soil samples collected around a MSWI, which is the largest in China. The International Toxicity Equivalency Quantity(I-TEQ) concentrations of PCDD/Fs in air samples were from 0.0300 to 1.03 pg I-TEQ/m~3(0.445–13.6 pg/m~3), with an average of 0.237 pg I-TEQ/m~3, while in soil samples they ranged from 0.520 to 3.40 pg I-TEQ/g(2.41–88.7 pg/g) with an average of1.49 pg I-TEQ/g. The concentrations of PCDD/Fs in air and soil samples were comparable to other areas, and Pe CDFs were the dominant contributors, which was different from stack gas homologue patterns. Multivariate statistical analysis showed that PCDD/Fs emission from the MSWI did not directly affect the profiles of PCDD/Fs in air and soils, so that vehicles and unidentified emission sources should be considered. The daily inhalation levels of PCDD/Fs for children(0.0110 to 0.392 pg I-TEQ/(kg·day) and adults(0.00600 to 0.221 pg I-TEQ/(kg·day) near the MSWI were lower than the tolerable daily intake of 1.00 to 4.00 pg WHO-TEQ/(kg·day), but in winter the values were higher than in summer. These results can be used as basic data for assessing the risk of PCDD/Fs exposure in residents living around this MSWI, and more monitoring programs and studies should be carried out around MSWIs.     

Environmental behaviors of phoxim with two formulations in bamboo forest under soil surface mulching

Phoxim (emulsifiable concentrate (EC) and granules (G)) has been widely used in bamboo forests. The persistence and magnitude of phoxim residues in the crop and soil must be investigated to ensure human and environmental safety. The environmental behaviors of the two formulations were investigated in a bamboo forest under soil surface mulching conditions (CP) and non-covered cultivation conditions (NCP). The half-lives of phoxim in soil under the two conditions in soil were 4.1–6.2 days (EC) and 31.5–49.5 days (G), respectively. Phoxim in EC could be leached from the topsoil into the subsoil. A minimized leaching effect was observed for G under NCP. Inversely, an enhanced leaching effect was observed for G under CP. The G formulation resulted in more parent compound (in bamboo shoots) and metabolite (in soil) residues of phoxim than in the case of EC, especially under CP conditions. In addition, the intensity and duration of the formulation effect on soil pH adjustment from G were more obvious than that from EC. Results showed that the environmental behaviors (distribution, degradation, residue) of phoxim in the bamboo forest were significantly influenced by the type of formulation. The prolongation effect from phoxim G might cause persistence and long-term environmental risk. However, bamboo shoot consumption could be considered relatively safe after applying the recommended dose of the two phoxim formulations.     

Effects of aging process on adsorption–desorption and bioavailability of fomesafen in an agricultural soil amended with rice hull biochar

Biochar has been introduced as an acceptable soil amendment due to its environmental benefits such as sequestering soil contaminants. However, the aging process in biochar amended soil probably decreases the adsorption capacity of biochar through changing its physico-chemical properties. Adsorption, leaching and bioavailability of fomesafen to corn in a Chinese soil amended by rice hull biochar after 0, 30, 90 and 180 days were investigated.Results showed that the addition of 0.5%–2% fresh biochar significantly increases the adsorption of fomesafen 4–26 times compare to unamended soil due to higher SSA of biochar. Biochar amendment also decreases fomesafen concentration in soil pore water by5%–23% resulting lower risk of the herbicide for cultivated plants. However, the aging process decreased the adsorption capacity of biochar since the adsorption coefficient values which was 1.9–12.4 in 0.5%–2% fresh biochar amended soil, declined to 1.36–4.16, 1.13–2.78 and 0.95–2.31 in 1, 3 and 6-month aged treatments, respectively. Consequently, higher desorption, leaching and bioavailable fraction of fomesafen belonged to 6-month aged treatment. Nevertheless, rice hull biochar was effective for sequestering fomesafen as the adsorption capacity of biochar amended soil after 6 months of aging was still 2.5–5 times higher compared to that of unamended soil.     

Availability of phosphorus to algae from eroded soil fractions

A study was conducted to determine the concentrations of algal-available P (P_aa) in unfractionated samples and size-classified separates of soil eroded from wheat stubble plots during a simulated rainfall experiment conducted in Warren County, Indiana, U.S.A. Run-off samples were collected, concentrated, dispersed by sonification, separated according to size and incubated with algal cells (Selanastrum capricornutum) in P-free nutrient medium for 2 weeks. Algal-available P in soil separates was determined by decreases in sediment inorganic P (P_i) over the incubation period. The initial concentrations of dissolved molybdate-reactive P_i (DMRP), P_i extractable with NaOH (NaOH-P_i), P_i extractable with HCl (HCl-P_i), organic P (P_o, and total P increased with decreasing particle size. A higher proportion of P_i was HCl-extractable in fractions > 2 μm than in clay-size separates. The level of P_aa in samples increased with decreasing particle size. Available P concentrations in separates < 0.2, 0.2–2, 2–50, > 50 μm and unfractionated samples averaged 447, 282, 113, 26 and 261 μg g^?1, respectively. From 42 to 69% of the P_i and 20–37% of the total P in unfractioned samples was P_aa. A lower proportion of P_i in the > 50 μm fraction was P_aa than in the other size fractions (34 vs. 50%). There was no relationship between particle size and the proportion of total P that was available. The majority (> 84%) of P_aa originated in the P_i fraction extractable with NaOH, whereas HCl-P_i only contributed small amounts of P_aa. The proportion of initial NaOH-P_i assimilated by algae in 2 weeks ranged between 43 and 77%, whereas an average of 16% of HCl-P_i in separates was P_aa. On average, a greater proportion of NaOH-P_i was assimilated by algae in samples from no-till plots as compared to those from chisel-plowed plots.