Experimental study on effect of anion surfactant on degradation rate of aldicarb in soil

Degradation kinetics of aldicarb [2-methyl-2-(methylthio) propionaldehyde O-(methyl carbamoyl) oxime] in surface and subsurface soil containing different levels of sodium dodecylbenzenesulfonate (SDBS) were determined to understand complex effect of SDBS on aldicarb degradation process. The results showed that degradation curves of aldicarb in soil can be described with first order kinetics formula and the degradation rate constant. k (d(-1)), in surface soil was larger than that in subsurface soil. SDBS can accelerate the degradation of aldicarb in soil and there was a good linear relationship between degradation rate constant and the logarithm of SDBS concentration. The possible reasons were that SDBS could change pH value of soil, have solubilization effect on aldicarb, and be used as carbon source of microorganisms. But SDBS had a larger promotion to the degradation of aldicarb in surface than in subsurface soil. When SDBS concentration was 1000 mg/kg of dried soil the first order degradation rate constant of aldicarb could be increased by 56.6 percent in surface soil and by 27.6 percent in subsurface soil, respectively.     

Fe(III)-oxalate complexes induced photooxidation of diethylstilbestrol in water

In this work, the photooxidation of diethylstilbestrol (DES), a synthetic estrogen, was investigated in a concentric reactor under a 125 W high-pressure mercury lamp (lambda > or = 365 nm). The photooxidation efficiencies were dependent on the pH values and Fe(III)/oxalate ratios of the system, with higher efficiency at pH 3.50+/-0.05 and Fe(III)/oxalate ratio 10.0/120.0 micromol l(-1). The photooxidation reactions obeyed the law of pseudo-first-order reaction at the concentration over the range of 2.0-10.0 mg l(-1) of DES. The photooxidation rates decreased with increasing the initial concentrations of DES. For 2.0 mg l(-1) DES, the observed photooxidation rate coefficient (k(obs)) was 0.00622 min(-1). By using GC-MS and LC-MS techniques, the predominant photooxidation products DES-o-catechol ([M](+), m/z 284) and DES-4-semiquinone ([M](-), m/z 267) were respectively identified and the mechanisms for the oxidative degradation were proposed. When DES reacted with OH radicals, C atoms in 3-position were added with OH radicals to produce hydrolyzed DES radical followed by two oxidation pathways: (1) dehydrolyzing to produce DES-4-semiquinone which was oxidized further to DES-4,4'-quinone; (2) undergoing peroxidation by O(2) and getting rid of HO(2) radical to produce DES-o-catechol. After that, the two H atoms on the hydroxy group of the catechol were extracted in two individual steps to form intermediates semiquinone radical and o-quinone. The catechol intermediates underwent further oxidation, benzene ring cleavage and decarboxylation, up to mineralization ultimately.     

Influences of metals on kinetics of methyl tert-butyl ether biodegradation by Ochrobactrum cytisi

The influence of zinc, manganese, and nickel on the degradation of MTBE (methyl tert-butyl ether), by an aerobic MTBE-degrading strain, Ochrobactrum cytisi, were investigated. The result showed that unlike previous findings, O. cytisi was able to degrade MTBE through direct metabolism when MTBE was present as the only carbon source. The degradation rate of MTBE was rapid, completed within 80 h. MTBE biodegradation by this strain was stimulated at low concentrations of Zn(2+) (1-5 mg l(-1)) and Mn(2+) (1-5 mg l(-1)) but inhibited at high concentrations of Zn(2+) (20 mg l(-1)) and Mn(2+) (20 mg l(-1)), and at low concentration of Ni(2+) (1-4 mg l(-1)). Kinetic parameters for MTBE degradation in the presence or absence of metals were obtained through nonlinear regression and a least-square minimization procedure. In all cases, a good agreement was achieved between kinetic simulations and experimental results.     

Activated carbon from industrial solid waste as an adsorbent for the removal of Rhodamine-B from aqueous solution: kinetic and equilibrium studies

The activated carbon was prepared using industrial solid waste called sago waste and physico-chemical properties of carbon were carried out to explore adsorption process. The effectiveness of carbon prepared from sago waste in adsorbing Rhodamine-B from aqueous solution has been studied as a function of agitation time, adsorbent dosage, initial dye concentration, pH and desorption. Adsorption equilibrium studies were carried out in order to optimize the experimental conditions. The adsorption of Rhodamine-B onto carbon followed second order kinetic model. Adsorption data were modeled using both Langmuir and Freundlich classical adsorption isotherms. The adsorption capacity Q0 was 16.12 mg g(-1) at initial pH 5.7 for the particle size 125-250 microm. The equilibrium time was found to be 150 min for 10, 20 mg l(-1) and 210 min for 30, 40 mg l(-1) dye concentrations, respectively. A maximum removal of 91% was obtained at natural pH 5.7 for an adsorbent dose of 100mg/50 ml of 10 mg l(-1) dye concentration and 100% removal was obtained when the pH was increased to 7 for an adsorbent dose of 275 mg/50 ml of 20 mg l(-1) dye concentration. Desorption studies were carried out in water medium by varying the pH from 2 to 10. Desorption studies were performed with dilute HCl and show that ion exchange is predominant dye adsorption mechanism. This adsorbent was found to be both effective and economically viable.     

超声波降解四环素类抗生素废水

采用超声波降解模拟废水中四环素类抗生素(TCs):土霉素(OTC)、四环素(TC)和金霉素(CTC),考查废水初始浓度、初始pH、超声波输入功率密度、曝气量和自由基清除剂(正丁醇)对降解效率的影响。结果表明,超声波可以快速高效地降解废水中的TCs,CTC最易被降解,TC和OTC次之;在OTC、TC和CTC初始浓度0.25 mg/L,初始pH=8.2,声功率密度1.2 W/mL,气水体积比30∶1的条件下,超声波辐照20 min后去除率分别达到76.8%、84.0%和94.4%。在实验研究条件下,TCs去除率均随初始浓度(0.25~2.00 mg/L)的增大而降低,但总去除浓度升高;碱性条件有利于TCs降解,去除率随初始pH(6~11)升高而升高;功率密度(0.24~1.96 W/mL)越高,TCs去除率也越高;曝气后TCs的去除率明显升高,随着气水比(10∶1~60∶1)的增大,去除率逐渐上升;正丁醇有效抑制TCs超声波降解,可推断TCs主要降解途径为自由基氧化。TCs超声波降解过程符合伪一级动力学反应特征。     

Influence of humic substances on the photolysis of aqueous pesticide residues

The present work investigated the direct and indirect photolysis of pesticide residues (atrazine, imazaquin, iprodione), in aqueous solutions and under UV-visible radiation (280-480nm). Different kinds of humic substances (HS) were added to samples in order to evaluate their behaviour as possible photocatalysts and their effect on the photolysis of pesticides. The fulvic acids were purchased from the International Humic Substances Society, and they were added to samples in concentrations ranging from 1 to 150 mgl(-1). Titanium dioxide was used as the photocatalyst, in concentration ranging from 10 to 150 mgl(-1). Pesticides photolysis were measured by UV-visible absorption spectroscopy and differential pulse polarography with all used pesticides, reaching total degradation after 2h of irradiation, thus indicating a fast direct photolysis. Photocatalysis by TiO(2) could increase the pesticides photolysis rate up to 40%. This effect, however, was not observed for imazaquin photolysis. Again, except for imazaquin, HS presence showed a positive effect in increasing pesticide degradation, but only within specific concentration ranges (below 10mg l(-1) for iprodione and about 30mgl(-1) for atrazine). Above these ranges HS induce a decrease in the pesticides photolysis rate. Spin-trapping measurements by electronic paramagnetic resonance spectroscopy, using the spin-trap DMPO, showed that HS are able to photogenerate hydroxyl radicals, increasing the pesticides molecule degradation. However, the HS also react with the photogenerated hydroxyl radical, influencing the pesticide photolysis, leading to a decrease in the photolysis rate and causing it to be strongly dependent on the nature and concentration of residues in the water to be treated.     

Influence of pH on persulfate oxidation of TCE at ambient temperatures

In situ chemical oxidation (ISCO) is a technology used for groundwater remediation. This laboratory study investigated the use of the oxidant sodium persulfate for the chemical oxidation of trichloroethylene (TCE) at near ambient temperatures (10, 20 and 30 degrees C) to determine the influence of pH (pH=4, 7 and 9) on the reaction rate (i.e., pseudo-first-order rate constants) over the range of temperatures utilized. TCE solutions (60 mg l(-1); 0.46 mM) were prepared in phosphate buffered RO water and a fixed persulfate/TCE molar ratio of 50/1 was employed in all tests. Half-lives of TCE degradation at 10, 20 and 30 degrees C (pH 7) were 115.5, 35.0 and 5.5h, respectively. Maximum TCE degradation occurred at pH 7. Lowering system pH resulted in a greater decrease in TCE degradation rates than increasing system pH. Radical scavenging tests used to identify predominant radical species suggested that the sulfate radical (SO(4)(.-)) predominates under acidic conditions and the hydroxyl radical (.OH) predominates under basic conditions. In a side by side comparison of TCE degradation in a groundwater vs. unbuffered RO water it was demonstrated that when the system pH is buffered to near neutral pH conditions due to the presence of natural occurring groundwater constituents that the TCE degradation rate is higher than in unbuffered RO water where the system pH dropped from 5.9 to 2.8. The results of this study suggest that in a field application of ISCO, pH should be monitored and adjusted to near neutral if necessary.     

Enhanced ozonation of simulated dyestuff wastewater by microbubbles

The ozonation of synthetic wastewater containing azo dye, CI Reactive Black 5, was investigated using a microbubble generator and a conventional bubble contactor. The microbubble generator produced a milky and high intensity microbubble solution in which the bubbles had a mean diameter of less than 58 microm and a numerical density of more than 2.9 x 10(4) counts ml(-1) at a gas flow rate of less than 0.5 l min(-1). Compared with the bubble contactor, the total mass transfer coefficient was 1.8 times higher and the pseudo-first order rate constant was 3.2-3.6 times higher at the same initial dye concentration of 100 mg l(-1), 230 mg l(-1) and 530 mg l(-1) in the proposed microbubble system. The amount of total organic carbon removed per g of ozone consumed was about 1.3 times higher in the microbubble system than in the bubble contactor. The test using terephthalic acid as the chemical probe implied that more hydroxyl radicals were produced in the microbubble system, which contributed to the degradation of the dye molecules. The results suggested that in addition to the enhancement of mass transfer, microbubbles, which had higher inner pressure, could accelerate the formation of hydroxyl radicals and hence improve the oxidation of dye molecules.     

Degradation of toxaphene in aged and freshly contaminated soil

Degradation of toxaphene in soil from both newly contaminated (from Sweden) and aged spills (from Nicaragua) were studied. The newly contaminated soil contained approximately 11 mg kg(-1) toxaphene while the aged Nicaraguan soil contained approximately 100 mg kg(-1). Degradation was studied in anaerobic bioreactors, some of which were supplied with lactic acid and others with Triton X-114. In this study we found that the lower isomers Parlar 11, 12 were degraded while the concentration of isomer Parlar 15 increased. This supported an earlier evaluation which indicated that less chlorinated isomers are formed from more heavily isomers. Lactic acid when added to the soil, interfere with the degradation of toxaphene. Lactic acid was added; several isomers appeared to degrade rather slowly in newly contaminated Swedish soil. The Swedish soil, without any external carbon source, showed the slowest degradation rate of all the compounds studied. When Triton X-114 at 0.4 mM was added, the degradation rate of the compounds increased. This study illustrates that biodegradation of toxaphene is a complex process and several parameters have to be taken into consideration. Degradation of persistent pollutants in the environment using biotechnology is dependent on bioavailability, carbon sources and formation of metabolites.     

Mineralization of paracetamol in aqueous medium by anodic oxidation with a boron-doped diamond electrode

The degradation of 100ml of solutions with paracetamol (N-(4-hydroxyphenyl)acetamide) up to 1 g l(-1) in the pH range 2.0-12.0 has been studied by anodic oxidation in a cell with a boron-doped diamond (BDD) anode and a graphite cathode, both of 3-cm2 area, by applying a current of 100, 300 and 450 mA between 25 and 45 degrees C. Complete mineralization is always achieved due to the great concentration of hydroxyl radical (*OH) generated at the BDD surface, with release of NH4+ and NO3- ions. The mineralization rate is pH-independent, increases with increasing applied current and temperature, but decreases when drug concentration raises from 315 mg l(-1). Reversed-phase chromatography revealed a similar complex paracetamol decay in acid and alkaline media. Ion-exclusion chromatography allowed the detection of oxalic and oxamic acids as ultimate carboxylic acids. When the same solutions have been comparatively treated with a Pt anode, a quite poor mineralization is found because of the production of much lower *OH concentration. Under these conditions, the degradation rate is enhanced in alkaline medium and polymerization of intermediates is favored in concentrated solutions. Paracetamol can be completely destroyed with Pt and its kinetics follows a pseudo-first-order reaction with a constant rate independent of pH.     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl(-) increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl(-) at total mineralization was detected when initial diuron concentration was 13.8 mg L(-1). For N species, the final concentrations of NO3(-) and NH4+ after 60 min of reaction time were 0.28 and 0.19 mg L(-1), respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na2CO3, additive NaHCO3 and additive H2O2 were all advantageous to improve the degradation efficiency of diuron.     

双频超声辐射协同H_2O_2降解偶氮染料废水的研究

采用双频超声协同H2O2降解酸性绿20染料废水,考察超声功率密度、染料初始浓度和pH、饱和气体及H2O2投加量等因素对酸性绿20降解效果的影响,结果表明,在给定实验条件下,双频降解效果优于单频超声波,且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解,当染料废水初始pH=4可取得最佳的降解效果;酸性绿20的降解效率随染料初始浓度的增大而降低,其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H2O2,可取得最佳的降解效果。在优化实验条件下,采用双频超声协同H2O2降解5 h,酸性绿20的色度和TOC去除率分别为94.6%和36.3%;分析降解前后的紫外-可见光谱图可知,酸性绿20并非完全被降解为CO2和H2O,而是生成一些小分子有机中间体。     

羟基氧化铁催化臭氧氧化去除水中阿特拉津

以实验室制备的羟基氧化铁(FeOOH)为催化剂,研究了其催化臭氧氧化去除水中痕量阿特拉津的效能,并对影响催化效果因素及降解机理进行了探讨。在本实验条件下,反应8 min时催化氧化阿特拉津的去除率比单独臭氧氧化高出63.2%,而FeOOH对阿特拉津的吸附量很小,结果表明,FeOOH对臭氧氧化水中的痕量阿特拉津具有明显的催化活性。探讨了催化剂投量、pH、阿特拉津初始浓度和重碳酸盐碱度对催化氧化阿特拉津的影响。催化剂最佳投量为150 mg/L,去除率随pH和阿特拉津初始浓度的增加而升高,重碳酸盐浓度为200 mg/L时催化作用受到明显抑制。通过研究叔丁醇对催化反应的影响间接推断了催化反应的机理,叔丁醇作为羟基自由基抑制剂有效地抑制了水中羟基自由基的生成和它对阿特拉津的氧化反应,间接证明这种催化作用遵循羟基自由基的反应机理。     

Biodegradation of triazine herbicide metribuzin by the strain Bacillus sp. N1

By enrichment culturing of soil contaminated with metribuzin, a highly efficient metribuzin degrading bacterium, Bacillus sp. N1, was isolated. This strain grows using metribuzin at 5.0% (v/v) as the sole nitrogen source in a liquid medium. Optimal metribuzin degradation occurred at a temperature of 30ºC and at pH 7.0. With an initial concentration of 20 mg L^?1, the degradation rate was 73.5% in 120 h. If the initial concentrations were higher than 50 mg L^?1, the biodegradation rates decreased as the metribuzin concentrations increased. When the concentration was 100 mg L^?1, the degradation rate was only 45%. Degradation followed the pesticide degradation kinetic equation at initial concentrations between 5 mg L^?1 and 50 mg L^?1. When the metribuzin contaminated soil was mixed with strain N1 (with the concentration of metribuzin being 20 mg L^?1 and the inoculation rate of 10¹¹ g^?1 dry soil), the degradation rate of the metribuzin was 66.4% in 30 days, while the degradation rate of metribuzin was only 19.4% in the control soil without the strain N1. These results indicate that the strain N1 can significantly increase the degradation rate of metribuzin in contaminated soil.     

介质阻挡放电氧化降解木质素磺酸钠的动力学研究

为了有效地处理难生物降解的造纸废水,采用气相介质阻挡放电产生氧化性物质,对木质素磺酸钠进行了氧化降解研究。在不同操作条件下,对其降解动力学及矿化程度进行了研究。结果表明,介质阻挡放电能有效地降解木质素磺酸钠,其氧化降解反应遵循准一级动力学反应。当峰值电压为20 kV,被水蒸气饱和的空气为气源,流量为7 L/min时,氧化处理60 min后,木质素磺酸钠降解率达到70％。其速率常数K随峰值电压、气源、气体流量和木质素磺酸钠的初始浓度的变化而不同。气体流量越大,木质素磺酸钠的初始浓度越低,速率常数K越大,降解效果越好。随着处理时间的增加,氧化性物质能将部分木质素磺酸钠矿化使溶液TOC降低,当被水蒸气饱和的空气作为气源时,氧化处理120min,21.38%的TOC被去除。     

Processes controlling the distribution and natural attenuation of dissolved phenolic compounds in a deep sandstone aquifer

Processes controlling the distribution and natural attenuation (NA) of phenol, cresols and xylenols released from a former coal-tar distillation plant in a deep Triassic sandstone aquifer are evaluated from vertical profiles along the plume centerline at 130 and 350 m from the site. Up to four groups of contaminants (phenols, mineral acids, NaOH, NaCl) form discrete and overlapping plumes in the aquifer. Their distribution reflects changing source history with releases of contaminants from different locations. Organic contaminant distribution in the aquifer is determined more by site source history than degradation. Contaminant degradation at total organic carbon (TOC) concentrations up to 6500 mg l(-1) (7500 mg l(-1) total phenolics) is occurring by aerobic respiration NO3-reduction, Mn(IV)-/Fe(III)-reduction, SO4-reduction, methanogenesis and fermentation, with the accumulation of inorganic carbon, organic metabolites (4-hydroxybenzaldehyde, 4-hydroxybenzoic acid), acetate, Mn(II), Fe(II), S(-II), CH4 and H2 in the plume. Aerobic and NO3-reducing processes are restricted to a 2-m-thick plume fringe but Mn(IV)-/Fe(II)-reduction, SO4-reduction, methanogenesis and fermentation occur concomitantly in the plume. Dissolved H2 concentrations in the plume vary from 0.7 to 110 nM and acetate concentrations reach 200 mg l(-1). The occurrence of a mixed redox system and concomitant terminal electron accepting processes (TEAPs) could be explained with a partial equilibrium model based on the potential in situ free energy (deltaGr) yield for oxidation of H2 by specific TEAPs. Respiratory processes rather than fermentation are rate limiting in determining the distribution of H2 and TEAPs and H2 dynamics in this system. Most (min. 90%) contaminant degradation has occurred by aerobic and NO3-reducing processes at the plume fringe. This potential is determined by the supply of aqueous O2 and NO3 from uncontaminated groundwater, as controlled by transverse mixing, which is limited in this aquifer by low dispersion. Consumption to date of mineral oxides and SO4 is, respectively, <0.15% and 0.4% of the available aquifer capacity, and degradation using these oxidants is <10%. Fermentation is a significant process in contaminant turnover, accounting for 21% of degradation products present in the plume, and indicating that microbial respiration rates are slow in comparison with fermentation. Under present conditions, the potential for degradation in the plume is very low due to inhibitory effects of the contaminant matrix. Degradation products correspond to <22% mass loss over the life of the plume, providing a first-order plume scale half-life >140 years. The phenolic compounds are biodegradable under the range of redox conditions in the aquifer and the aquifer is not oxidant limited, but the plume is likely to be long-lived and to expand. Degradation is likely to increase only after contaminant concentrations are reduced and aqueous oxidant inputs are increased by dispersion of the plume. The results imply that transport processes may exert a greater control on the natural attenuation of this plume than aquifer oxidant availability.     

Using polymer mats to biodegrade atrazine in groundwater: laboratory column experiments

Large-scale column experiments were undertaken to evaluate the potential of in situ polymer mats to deliver oxygen into groundwater to induce biodegradation of the pesticides atrazine, terbutryn and fenamiphos contaminating groundwater in Perth, Western Australia. The polymer mats, composed of woven silicone (dimethylsiloxane) tubes and purged with air, were installed in 2-m-long flow-through soil columns. The polymer mats proved efficient in delivering dissolved oxygen to anaerobic groundwater. Dissolved oxygen concentrations increased from <0.2 mg l(-1) to approximately 4 mg l(-1). Degradation rates of atrazine in oxygenated groundwater were relatively high with a zero-order rate of 240-380 microg l(-1) or a first-order half-life of 0.35 days. Amendment with an additional carbon source showed no significant improvement in biodegradation rates, suggesting that organic carbon was not limiting biodegradation. Atrazine degradation rates estimated in the column experiments were similar to rates determined in laboratory culture experiments, using pure cultures of atrazine-mineralising bacteria. No significant degradation of terbutryn or fenamiphos was observed under the experimental conditions within the time frames of the study. Results from these experiments indicate that remediation of atrazine in a contaminated aquifer may be achievable by delivery of oxygen using an in situ polymer mat system.     

超声波光催化协同降解对甲基苯磺酸水溶液的机理研究

采用超声波与光催化联合法对模拟废水中难生物降解的对甲基苯磺酸(4-TSA)进行降解实验研究,借助紫外光谱、红外光谱、质谱、气相色谱、高效液相色谱、化学需氧量和总有机碳的检测结果对反应机理进行了初步探讨.实验结果表明:超声波和光催化之间存在着协同效应;当溶液初始质量浓度30 mg/L,光催化剂TiO2投加量为100 mg...     

双频超声辐射协同H2O2降解偶氮染料废水的研究

采用双频超声协同H₂O₂降解酸性绿20染料废水,考察超声功率密度、染料初始浓度和pH、饱和气体及H₂O₂投加量等因素对酸性绿20降解效果的影响,结果表明,在给定实验条件下,双频降解效果优于单频超声波,且降解率随超声功率密度的增大而增大。酸性条件有利于酸性绿20的降解,当染料废水初始pH=4可取得最佳的降解效果;酸性绿20的降解效率随染料初始浓度的增大而降低,其优化初始浓度为40 mg/L。在反应体系中通入空气并投加H₂O₂,可取得最佳的降解效果。在优化实验条件下, 采用双频超声协同H₂O₂降解5 h,酸性绿20的色度和TOC去除率分别为94.6%和36.3%;分析降解前后的紫外可见光谱图可知,酸性绿20并非完全被降解为CO₂和H₂O,而是生成一些小分子有机中间体。     

Sonochemical degradation of a pharmaceutical waste,atenolol, in aqueous medium

Atenolol is a β-blocker drug and an identified emerging pollutant. Advanced oxidation processes (AOPs) utilise the reaction of a highly oxidising species (hydroxyl radicals, ^?OH) for the mineralisation of emerging pollutants since conventional treatment methodologies generally fail to degrade these compounds. In the present work, degradation of atenolol was carried out using ultrasound with frequencies ranging from 200 kHz to 1 MHz as a source of hydroxyl radical. The degradation was monitored by HPLC, total organic carbon (TOC) and chemical oxygen demand (COD) reduction and ion chromatography (IC). Nearly 90 % of degradation of atenolol was observed with ultrasound having 350 kHz. Both frequency and power of ultrasound affect the efficiency of degradation. Nearly 100 % degradation was obtained at a pH of 4. Presence of various additives such as sodium dodecyl sulphate, chloride, sulphate, nitrate, phosphate and bicarbonate was found to reduce the efficiency of degradation. Although nearly 100 % degradation of atenolol was observed under various experimental conditions, only about 62 % mineralisation (from TOC and COD measurements) was obtained. Nearly eight intermediate products were identified using high-resolution mass spectrometry (LC-Q-TOF). These products were understood as the results of hydroxyl radical addition to atenolol. The degradation studies were also carried out in river water which also showed a similar degradation profile. A mechanism of degradation and mineralisation is presented.