Pesticides in rainfall in Europe

Papers and published reports investigating the presence of pesticides in rainfall in Europe were reviewed. Approximately half of the compounds that were analysed for were detected. For those detected, most concentrations were below about 100 ng/l, but larger concentrations, up to a few thousand nanograms per litre, were detected occasionally at most monitoring sites. The most frequently detected compounds were lindane (gamma-HCH) and its isomer (alpha-HCH), which were detected on 90-100% of sampling occasions at most of the sites where they were monitored. For compounds developed more recently, detection was usually limited to the spraying season. A classification of pesticides according to their deposition pattern is proposed.     

膜分离技术在油气回收中的应用

简单阐述了油气回收的意义,并对几种常用的油气回收方法进行了介绍,分析其优缺点,重点论述了膜分离技术在油气回收中的应用,以及国内外的进展情况和典型应用实例,最后对膜法油气回收与其它方法作了比较,对膜法回收现阶段的存在问题进行了剖析,并对今后的研究方向提出了建议。研究结果表明,膜法是一种大有前途的油气回收方法。     

The significance of PCBs in the atmosphere of the southern hemisphere

Air monitoring stations were set up at 2 sites in the southern hemisphere--Moody Brook, Falkland Island (51 degrees 25' S, 57 degrees 56' W) and Halley, Research Station, Antarctica (75 degrees 35' S, 26 degrees 30' W). PCBs were monitored at the stations throughout 1999. Highest concentrations were observed when temperatures were greater. In general, concentrations were greater at Moody Brook than at Halley, although the difference in concentrations between sites was less for more chlorinated congeners. Air concentrations at both sites were compared with samples collected nearby over-water. Over water air concentrations were found to be greater than over land air concentrations. Concentrations were also compared with literature data for air concentrations at a remote site in the Canadian Arctic. Atmospheric concentrations of tri-chlorinated biphenyls were found to be approximately double those reported for Ellesmere Island in the Canadian Arctic, whilst concentrations in samples from Antarctica were very similar to those found in the high Arctic. Most other PCBs were a factor of 2-4 greater in the Canadian Arctic.     

Identification and level estimation of chlorinated neutral aromatic sulfur compounds and their alkylated derivatives in pulp mill effluents and sediments

Seven effluent samples from a modern pulp mill, in which chlorine and chlorine dioxide bleaching is used, and five sediment samples from the recipient watercourse were investigated for polychlorinated dibenzothiophenes (PCDBTs), polychlorinated thianthrenes (PCTAs), polychlorinated diphenylsulfides (PCDPSs) and for alkylated derivatives of these. Mainly di-, tri-, tetra- and pentachlorinated congeners were studied. Particles and filtrates from the effluents were analyzed separately. The concentration levels of the nonalkylated compounds were found to be higher in the filtrates than in the particles. Trichlorinated dibenzothiophenes and thianthrenes were found as the major congeners. Pentachlorinated derivatives were not found. Alkylated di- and trichlorodibenzothiophenes were detected in some samples, while alkylated chlorinated thianthrenes and diphenylsulfides were nondetectable. The estimated concentration levels of the compounds detected were in the range of 40–2700 pg/L in the pulp mill effluents and in the range of 2–40 pg/g dry weight in the sediments. Mixtures of methylated di- and trichlorodibenzothiophenes used as references in analyses were prepared from methylchlorobiphenyls. Some new pure model compounds were obtained by HPLC fractionation of the chlorination mixture of dibenzothiophene. Structures of these were determined by ¹H NMR.     

Thermal exploitation of wastes with lignite for energy production

The thermal exploitation of wastewood with Greek lignite was investigated by performing tests in a laboratory-scale fluidized bed reactor, a 1-MW(th) semi-industrial circulating fluidized bed combustor, and an industrial boiler. Blends of natural wood, demolition wood, railroad sleepers, medium-density fiberboard residues, and power poles with lignite were used, and the co-combustion efficiency and the effect of wastewood addition on the emitted pollutants were investigated. Carbon monoxide, sulfur dioxide, and oxides of nitrogen emissions were continuously monitored, and, during the industrial-scale tests, the toxic emissions (polychlorinated dibenzodioxins and dibenzofurans and heavy metals) were determined. Ash samples were analyzed for heavy metals in an inductively coupled plasma-atomic emission spectroscopy spectrophotometer. Problems were observed during the preparation of wastewood, because species embedded with different compounds, such as railway sleepers and demolition wood, were not easily treated. All wastewood blends were proven good fuels; co-combustion proceeded smoothly and homogeneous temperature and pressure profiles were obtained. Although some fluctuations were observed, low emissions of gaseous pollutants were obtained for all fuel blends. The metal element emissions (in the flue gases and the solid residues) were lower than the legislative limits. Therefore, wastewood co-combustion with lignite can be realized, provided that the fuel handling and preparation can be practically performed in large-scale installations.     

城市下水污泥焚烧过程中二次污染物排放特性的试验研究

在0.15 MWt循环流化床燃烧试验台上进行了城市下水污泥与煤的混烧试验,分析了烟气中的二次污染物排放特性.分析结果表明,利用循环流化床焚烧城市下水污泥时,添加辅助燃料(如煤)及改变焚烧条件,不仅可以达到稳定燃烧的目的,而且有利于抑制焚烧中二次污染物(如CO及二恶英等有机污染物)的生成.分析了焚烧污泥污染物的排放特性,为采用焚烧方式处理城市下水污泥提供了基础性试验数据.     

Factors inhibiting bioremediation of soil contaminated with weathered oils and drill cuttings

Oily drill cuttings and a soil contaminated with weathered crude oils were treated by enhanced biodegradation under tropical conditions in industrial scaled experiments. Oil contaminants were characterized by gas chromatography and mass spectrometry. This allowed for the identification of a mixture of two crude oils in the contaminated soil. After 12 months of bioremediation process, the removal of hydrocarbons reached by biodegradation an extent of 60% although nutrient amendment with elevated concentration of N-urea had highly detrimental effects on the hydrocarbon degrading fungal populations due to the production of toxic concentration of ammonia gas by nitrification. The saturated hydrocarbons were extensively assimilated, though n-alkanes were not completely removed. Aromatic hydrocarbons were less degraded than saturated whereas resin and asphaltene fractions were, surprisingly, partly assimilated. In laboratory conditions, the residual hydrocarbons in the field-treated materials were 15-20% further degraded when metabolic byproducts resulting from biodegradation were diluted or removed.     

The metabolism of some chlorinated dibenzofurans by rats

Rats were given single oral doses of 2-chloro-, 2,8-dichloro-, 2,3,8-trichloro- and octachloro-dibenzofuran. Urine, faeces, fat and liver were analysed for starting materials and metabolites. The mono-, di- and trichlorodibenzofurans yielded mono- and dihydroxy derivatives, but metabolites containing sulphur were detected only with the mono- and dichlorodibenzofuran.Contrary to the chlorodibenzo-p-dioxins, where hydroxylated metabolites with substitution only at the 2,3-positions were isolated, chlorodibenzofuran-metabolites show a wider substitution pattern; five monohydroxy-derivatives were found, for instance, from 2,8-dichlorodibenzofuran.No metabolites were detected in urine, faeces and tissues of rats which were fed with octachlorodibenzofuran.     

Interaction of ozone exposure and Fusarium subglutinans inoculation on growth and disease development of loblolly pine seedlings

Seedlings from ten half-sib families of loblolly pine (Pinus taeda) were exposed in open-top chambers to carbon-filtered air (CF), non-filtered air (NF), or air amended with ozone to 1.7 or 2.5 times ambient. After 105 days of exposure, half the seedlings within each family were wounded but not inoculated and half were wounded and inoculated with the pitch canker fungus, Fusarium subglutinans, to which five families were relatively resistant. After an additional 50 days of ozone treatment, seedling growth and canker development were recorded. Cankers were significantly (sigma < or = 0.05) smaller among resistant compared to susceptible families, and were significantly larger among seedlings receiving the highest (2.5) compared to the ambient (NF) ozone treatment. The wound scars of non-inoculated seedlings were also significantly larger among seedlings receiving the 2.5 compared to the NF treatment, but these dimensions did not differ significantly with seedling family or resistance. The weights of needles and large roots were significantly smaller at the 2.5 compared to the 1.7 ozone treatment for inoculated but not for non-inoculated seedlings; this resulted in a significant interaction for ozone and inoculation effects. Among resistant families, root weights were significantly smaller for inoculated seedlings. Diameter growth and dry weights of needles were significantly smaller among inoculated compared to non-inoculated seedlings, but did not differ between NF and 2.5 ozone treatments.     

Effects of cadmium on the performance and microbiology of laboratory-scale lagoons treating domestic sewage

Two experiments were performed to assess the impact of cadmium on the sewage lagoon wastewater treatment process. For each one, three laboratory-scale pilot plants with one tank receiving the same raw effluent were used; one plant served as control and the other two were contaminated once only with cadmium. In the first study, the effects of a shock load of two concentrations of cadmium chloride (60 and 300 micrograms/l) on the plant performance, microbial populations (protists and bacteria) and enzyme activities were determined. Initially, most of the performance parameters were affected concentration-dependently. A reduction in the protist population density and some influence on the total bacterial population were observed, and the potential enzymatic activities were also modified. A second experiment with a lower cadmium concentration (30 micrograms/l), supplied as chloride or sulphate, still perturbed most of the parameters studied, and the effects of the two cadmium salts were identical.     

Evaluation of retrofit crankcase ventilation controls and diesel oxidation catalysts for reducing air pollution in school buses

This study evaluates the effect of retrofit closed crankcase ventilation filters (CCFs) and diesel oxidation catalysts (DOCs) on the in-cabin air quality in transit-style diesel school buses. In-cabin pollution levels were measured on three buses from the Pueblo, CO District 70 fleet. Monitoring was conducted while buses were driven along their regular routes, with each bus tested three times before and three times after installation of control devices. Ultrafine number concentrations in the school bus cabins were 33–41% lower, on average, after the control devices were installed. Mean mass concentrations of particulate matter less than 2.5 μm in diameter (PM2.5) were 56% lower, organic carbon (OC) 41% lower, elemental carbon (EC) 85% lower, and formaldehyde 32% lower after control devices were installed. While carbon monoxide concentrations were low in all tests, mean concentrations were higher after control devices were installed than in pre-retrofit tests. Reductions in number, OC, and formaldehyde concentrations were statistically significant, but reductions in PM2.5 mass were not. Even with control devices installed, during some runs PM2.5 and OC concentrations in the bus cabins were elevated compared to ambient concentrations observed in the area. OC concentrations inside the bus cabins ranged from 22 to 58 μg m^?3 before and 13 to 33 μg m^?3 after control devices were installed. OC concentrations were correlated with particle-bound organic tracers for lubricating oil emissions (hopanes) and diesel fuel and tailpipe emissions (polycyclic aromatic hydrocarbons (PAH) and aliphatic hydrocarbons). Mean concentrations of hopanes, PAH, and aliphatic hydrocarbons were lower by 37, 50, and 43%, respectively, after the control devices were installed, suggesting that both CCFs and DOCs were effective at reducing in-cabin OC concentrations.     

In situ and laboratory bioassays using Poecilia reticulata Peters, 1859 in the biomonitoring of an acidic lake at Camaçari, BA, Brazil

The suitability and viability of acute in situ bioassays were investigated in the biomonitoring program of an acidic lake contaminated with sulphur residues. Responses of organisms observed in laboratory and in situ bioassays were also assessed to determine whether or not they were similar and comparable, regarding accuracy and precision. Newborn Poecilia reticulata were employed as test organisms and exposed to the same water samples under in situ and laboratory conditions. Mortality/immobility was the endpoint assessed and dead/immobile organisms were counted at various time intervals during exposure. The mean calculated LT50 values and 95% confidence intervals were 1.61 (1.36-1.87) h in the laboratory bioassays and 0.72 (0.55-0.89) h in the in situ bioassays. Statistical comparison of these values revealed a significant difference (p<0.05). In situ bioassays were more accurate than those carried out in the laboratory, demonstrating higher sensitivity and better reproduction of what occurs in nature, while laboratory bioassays were more precise.     

Main products and kinetics of the thermal degradation of polyamides

The thermal degradation of the polyamides (PA) 6, 12, 66 and 612 was investigated by means of thermal analysis/mass spectrometry (TA-MS) and pyrolysis in a german standard oven. Sample masses were about 20 and 40 mg. The heating rates used in the dynamic studies were 1, 5 and 10 K min(-1). Both air and nitrogen atmospheres were utilized. The kinetic parameters were calculated from the TA-MS measurements and the main decomposition products were registered online. The evolved products from the pyrolysis oven were captured and analyzed off-line by GC/MS.     

城市下水污泥焚烧过程中二次污染物排放特性的试验研究

在0．15MWt循环流化床燃烧试验台上进行了城市下水污泥与煤的混烧试验，分析了烟气中的二次污染物排放特性。分析结果表明，利用循环流化床焚烧城市下水污泥时，添加辅助燃料（如煤）及改变焚烧条件，不仅可以达到稳定燃烧的目的，而且有利于抑制焚烧中二次污染物（如CO及二恶英等有机污染物）的生成。分析了焚烧污泥污染物的排放特性。为采用焚烧方式处理城市下水污泥提供了基础性试验数据。     

Measurements and modelling of cloudwater deposition to moorland and forests

The objective of the study was to measure the size dependence of cloudwater deposition and associated average ionic fluxes to vegetated surfaces. Measurements were made over a forest canopy at Dunslair heights in south Scotland and a moorland site, Great Dun Fell, in northern England. Measurements were made using the gradient and eddy correlation techniques. Eddy correlation measurements were made using an ultrasonic anemometer, a Knollenberg forward scattering spectrometer probe (to measure liquid water fluxes and fluxes of droplets in 1 microm size intervals) and a GSI particulate volume monitor (to measure liquid-water fluxes). Measurements were made at Great Dun Fell of the size dependence of droplet deposition velocity, using the gradient technique with two Knollenberg probes. Simultaneous gradient and eddy correlation measurements were also made at Great Dun Fell of average cloud-water fluxes, together with chemical analysis of cloud water composition, using a continuous analysis system. At Dunslair Heights, eddy correlation measurements were made using both the Knollenberg and Gerber Scientific Instruments (GSI) probes, while simultaneous gradient measurements using two GSI probes were also attempted. Samples of cloud water were collected at Dunslair Heights, using passive string collectors for chemical analysis by ion chromatography. The major findings of the study were: 1. The droplet deposition velocities measured by the two techniques were similar. 2. The deposition velocities were a strong function of droplet size. Considerable resistance to deposition was evident for droplets of less than 5 microm radius. Deposition velocities for particles from about 6 to 8 microm exceeded those for momentum. 3. Except when the droplets were very small or the winds very light, bulk cloud-water deposition velocities were about 80% or more of the momentum deposition velocities to forests.     

江苏盐城滩涂土壤中多环芳烃的测定

文中采用江苏盐城滩涂响水到滨海一带的滩涂土壤样品,利用索氏提取法提取、硅胶柱净化、高效液相色谱法分离检测土壤样品中的多环芳烃(PAHs),并用优化洗脱程序对滩涂土壤中PAHs的含量进行了测定。结果表明:11个滩涂土壤样品中检出萘、苊烯、菲、蒽、荧蒽、芘六种PAHs,其含量较低,说明该段滩涂土壤尚未受到多环芳烃的污染。     

Participate and Gaseous Emissions from Natural Gas Furnaces and Water Heaters

Three furnaces and one hot water heater were tested for particulate and gaseous emissions. The effects of fuel, stoichiometry, operating conditions, and appliance type on emission levels were studied. The filterable particulate levels from a properly operating furnace were very low. However, condensable particulate emissions were considerably greater, approximately the same as predicted by EPA estimates of furnace particulate emissions. Carbon emissions comprised about 12% of filterable particulate emissions. However, when operated highly fuel-rich, copious amounts of elemental carbon particles were emitted with a mass median diameter of less than 0.4 μm. Gaseous emissions were dependent on cycling of the furnace and stoichiometry.

An estimate was made of the daily furnace emissions compared to daily emissions from a 1980 catalyst-equipped automobile. While gaseous emissions were less than the corresponding vehicle emissions, the particle emissions from the furnace were three times greater than particle emissions from a 1980 vehicle.     

Toxic emissions during co-combustion of biomass-waste wood-lignite blends in an industrial boiler

The objectives of this work were to study the PCDD/F emissions during the co-combustion of waste wood/coal co-combustion in an industrial boiler and to determine the relation of the toxic emissions to the fuel properties. Co-combustion experiments were performed in a 13.8 MWthermal industrial moving grate combustor. The fuels which were examined in this study included Greek lignite, natural uncontaminated wood, power poles and medium density fibers (MDFs) which were by-products of the plant production process. Fuel blends were prepared by mixing single components in various concentrations. PCDD/F emissions were collected during experimental runs and were analyzed according to standard methods. Low PCDD/F emissions were obtained during the co-combustion tests, lower than the limit value of 0.1 ng TEQ/Nm3. The lowest values were observed during the combustion of fuel blends containing MDF, possibly due to the inhibitory action of some of the N-containing MDF ingredients, such as urea. No direct correlation was found between the PCDD/F and the copper emissions, while examination of the PCDD/F homologue patterns revealed the predominance of the lower chlorinated isomers over the higher ones.     

微细水雾除尘技术的实验研究

分析了煤矿并下呼吸性粉尘防治技术现状，并对水的超声雾化技术进行了实验研究，应用回归分析建立了超声雾化性能的数学模型。在分析微细水雾捕尘机理及捕尘水雾凝并沉降技术的基础上，设计了一集微细水雾捕尘-凝聚、凝并降尘-惯性沉降分离为一体的含尘气流净化系统，并对该系统的除尘效率进行了实验研究，建立了相应的数学模型。     

Detection of organic pollutants in sandy soils via TDR and eigendecomposition

In this study, organic pollutants in sandy soils are detected using a time domain relectrometry (TDR) probe system and eigendecomposition technique. As a demonstration, four types of organic fluids (motor oil, diesel oil, methanol and ethanol) were examined. Samples were prepared with different combinations of deionized water and organic fluid contents. For each experiment, reflected signals were captured by an oscilloscope, and their characteristics were identified using eigendecomposition technique. Autoregressive modeling and singular value decomposition methods were utilized for calculating the eigenvalues. The most significant eigenvalues were then identified based on their relative magnitude. Experimental results indicated that the presented system is sensitive to both water and pore fluid organic contents. For saturated conditions, signature curves were determined for identification of organic and/or water contents in soil pore fluids.