铁改性酵母粉对锑酸盐的吸附机理

采用氯化铁(FeCl3)制备了铁改性酵母粉，测试其对溶液中锑酸盐(Sb(V))的吸附性能，考察了FeCl3浓度、溶液pH以及酵母粉投加量对Sb(V)去除的影响，研究了Sb(V)在铁改性酵母粉表面的吸附动力学、吸附等温线特征，并用SEM-EDS、ATR-FTIR、XRD、XPS等方法对改性酵母粉进行表征以探究其吸附机理.结果表明，改性酵母粉吸附Sb(V)的最佳条件为：FeCl3浓度0.5 mol·L^-1、酵母粉投加量2 g·L^-1、pH 3.0.5 mol·L^-1 FeCl₃改性酵母粉(0.5 Fe-Y)对溶液中Sb(V)的最大去除率为91.2%，吸附容量达68.15 mg·g^-1.0.5 Fe-Y对Sb(V)的吸附符合伪二级动力学和Langmuir等温线模型，该吸附过程属于化学吸附，涉及络合反应和静电吸附. FeCl₃改性能显著增强酵母粉对Sb(V)的吸附能力，酵母粉表面羟基等官能团增多、电位增加、晶形结构更加无序以及表面羟基铁与Sb(V)形成内层络合物是...     

四环素在矿化垃圾上的吸附特性及动态过程

为明确垃圾渗滤液中四环素在矿化垃圾上的吸附规律,通过傅里叶红外光谱（FTIR）、X射线光电子能谱（XPS）、孔径测试及N₂吸附解吸测试表征了矿化垃圾的结构特点和化学性质,探讨了矿化垃圾对四环素的静态吸附规律及初始浓度、pH和不同阳离子类型等环境因素对其吸附效率的影响,并进一步通过动态吸附实验模拟了实际动态条件下的吸附过程.结果表明,矿化垃圾表面含有大量的官能团及良好的孔隙结构;矿化垃圾对四环素具有良好的吸附效果,吸附过程符合Freundlich等温吸附模型和拟二级动力学模型;初始浓度和pH升高会降低吸附效率,K⁺对吸附性能的抑制高于Ca²⁺离子;动态吸附实验表明矿化垃圾对四环素的承载量为3.9 mg·g^-1,动态吸附性能良好.     

氢氧化钠改性生物炭/凹凸棒石复合材料对铅、镉的吸附机理研究

利用水稻秸秆与凹凸棒石在缺氧条件下热解制备稻秆生物炭/凹凸棒石复合材料(BA),并通过氢氧化钠改性提升其吸附性能。通过吸附动力学、等温吸附及改变初始pH等吸附试验研究复合材料在Cd、Pb一元及二元污染体系中的吸附行为,并结合扫描电镜能谱(SEM-EDS)、比表面积及孔径分析(BET)、傅里叶变换红外光谱(FTIR)、X射线衍射(XRD)及X射线光电子能谱分析(XPS)等表征手段深入分析改性后复合材料对溶液中重金属Cd、Pb的吸附机理。试验结果表明氢氧化钠改性复合材料(NBA)对Cd²⁺和Pb²⁺的吸附容量分别为117.05和274.65 mg·g^-1,其去除效率比BA分别增加31.2%和51.7%。在二元金属体系中NBA吸附能力也明显优于BA,准二级动力学模型和Langmuir等温模型能更好地用于模拟吸附结果,表明该吸附主要为单分子化学吸附过程。此外,竞争吸附分析表明在Cd、Pb共存溶液中,与Cd²⁺相比,Pb²⁺更易被复合材料吸附。通过SEM-EDS、FTIR、XRD和XPS...     

膨化活性生物炭高效吸附双酚A的机理研究

物理和化学改性方法会引起生物炭理化性质和微观结构的改变,从而影响其对污染物的吸附.通过对玉米粒进行微波膨化制备出膨化生物炭,再用氢氧化钠和磷酸分别对膨化生物炭进行改性制备膨化活性生物炭.利用SEM、BET、FT-IR和XRD等手段对生物炭材料进行表征.通过吸附试验探究了膨化和活化过程对生物炭吸附双酚A(BPA)的影响.结果发现,膨化后炭材料比表面积增大,吸附量增加.膨化结合酸活化的生物炭比表面积最大(856.34 m2·g^-1),对双酚A的吸附量也最大(220.73 mg·g^-1),吸附量较未经膨化和活化的生物炭提升了7倍.膨化结合碱活化的生物炭孔结构更加发达,平均孔径为6种材料中最大(2.25 nm). Langmuir模型能够较好地拟合6种生物炭对BPA的吸附等温线,说明吸附过程以单层吸附为主.吸附位点能量分析表明,BPA在低浓度时优先占据碳材料表面的高能位点,高浓度时转为占据较低能量的位点.内扩散模型分析说明膨化和活化均能提高扩散过程速率.     

生物炭对土壤中阿特拉津吸附特征的影响

为探究生物炭对土壤中阿特拉津的吸附特征及影响因素,采用批处理实验研究了灭菌(T1)、5%秸秆生物炭+灭菌(T2)、未灭菌(T3)和5%秸秆生物炭+未灭菌(T4)条件下对土壤中阿特拉津吸附特征及土壤理化性质的影响.结果表明,在最初0—12 h内,不同处理下阿特拉津吸附量均随时间的延长而快速增加,而在12—96 h内增加较为缓慢并逐渐趋于平衡.在96 h时,T2和T4处理下阿特拉津最大吸附量分别达到46.22 mg·kg^-1和46.43 mg·kg^-1,而未添加生物炭的T1和T3处理则有所降低,分别为44.20 mg·kg^-1和43.09 mg·kg^-1.准二级动力学模型更好地拟合不同处理下土壤对阿特拉津吸附特征,T2和T4处理下吸附速率常数K分别为0.257 kg·mg^-1·h^-1和0.339 kg·mg^-1·h^-1,显著高于未添加生物炭处理的T1和T3处理(K分别为-0.083 kg·mg^-1·h^-1和-0.261 kg·mg^-1·h^-1).内扩散模型显示添加生物炭后,土壤对阿特拉津的吸附是一个由边界扩散、内部孔隙扩散等多因素控制的复杂化学过程.添加生物炭可显著提高土壤pH、有机碳、碱解氮、速效磷和速效钾含量,其中土壤有机碳含量与阿特拉津最大吸附量之间存在显著的正相关关系(P<0.05).由此可见,添加生物炭可以提高土壤对阿特拉津的固持能力,减少其淋溶迁移风险,从而达到修复阿特拉津污染土壤的目的.     

废弃茶叶吸附剂去除水中的氟离子

地热温泉常含有高浓度的氟,给温泉利用带来不可忽视的环境问题,因此温泉水中氟离子吸附净化处理是重要的研究热点.本文采用废弃茶叶作为吸附剂,氟离子为目标离子,优化了茶叶吸附剂种类、溶液pH对吸附效果的影响.在pH 3、初始浓度为5 mg·L^-1时,大红袍茶叶对氟离子的吸附容量达到0.126 mg·g^-1.进一步考察了吸附剂对氟离子的吸附机制,结果表明,氟离子吸附符合Pseudo-secondorder动力学模型,等温线符合Freundlich模型,氟离子吸附过程主要通过与茶叶中的羟基和羧基活性基团发生交换作用.茶叶氟吸附量虽较其它天然吸附剂略低但无需复杂改性和前处理,具有环境友好,成本低廉,来源丰富,易与获得等优点,在含氟水净化处理具有潜在应用和发展前景.     

以NH2-MIL-53(Al)为前驱体制备多孔掺碳Al2O3吸附剂及其对水中Cr(Ⅵ)的吸附性能

铬是污染性金属元素,铬含量是水质污染控制的一项重要指标,其中Cr(Ⅵ)的毒性最大,且易被人体吸收.本研究以水中的Cr(Ⅵ)吸附传质分离为目标,利用以铝为金属源水热法合成的铝基MOFs为前驱体,600℃煅烧后制备了多孔掺碳Al₂O₃吸附材料,利用现代分析技术对其进行微观结构表征,探究了其吸附作用能力与机制.研究结果表明,XRD、SEM、BET等表征手段证明了NH₂-MIL-53(Al)与多孔掺碳Al₂O₃结构的成功合成.前驱体NH₂-MIL-53(Al)和煅烧后的衍生物多孔掺碳Al₂O₃,在形貌上相似,且多孔掺碳Al₂O₃材料(180.24 m²·g^-1)的比表面积要大于NH₂-MIL-53(Al)(116.73 m²·g^-1).多孔掺碳Al₂     

氮改性对生物炭理化性质的影响及其对废水中铜离子的吸附特性

原状生物炭对废水中污染物的去除效果有限,改性是提高其吸附能力的重要途径.本文以水稻秸秆为对象,尿素为改性剂,在700℃无氧热解条件下分别制备了原状秸秆生物炭（RSBC）和氮改性秸秆生物炭（N-RSBC）,采用扫描电子显微镜（SEM）、比表面积分析仪（BET）、元素分析仪（EA）、Zeta电位、X射线衍射（XRD）、傅里叶红外光谱（FTIR）以及X射线光电子能谱（XPS）对RSBC和N-RSBC的形貌、比表面积、元素组成、矿物类型和官能团进行表征,考察溶液初始pH值、离子类型和离子强度对生物炭吸附Cu²⁺的影响,并结合吸附等温线和吸附动力学实验、吸附后表征结果探究生物炭对废水中Cu²⁺的吸附性能和机理.结果表明,氮改性导致了生物炭的比表面积和孔体积的降低,而生物炭的官能团类型却更加丰富,特别是含氮官能团.当溶液初始pH值从2.0增加到6.0,生物炭对于Cu²⁺的去除率逐渐增加.对RSBC而言,Na⁺、K⁺、Ca²⁺、Mg2+的存在能略微增加其对Cu^...     

水环境中天然有机物对纳米颗粒吸附铅和镉的不同作用

为阐明天然有机物(NOM)在纳米颗粒(NPs)吸附重金属中的作用,研究了蛋白质(牛血清白蛋白,BSA)、碳水化合物(海藻酸钠,NaAlg)和腐殖酸(HA)对二氧化钛纳米颗粒(TNPs)和氧化铈纳米颗粒(CNPs)聚集沉降和吸附Cd²⁺和Pb²⁺的影响.结果表明,当Pb²⁺和Cd²⁺在20—120 mg·L-1范围内,HA和NaAlg显著促进了TNPs和CNPs对这些金属离子的吸附(P<0.05),而BSA对这些金属吸附的影响甚微.TNPs-HA和TNPs-NaAlg对Pb²⁺的吸附分别提高了14%—41%和16%—57%,对Cd²⁺的吸附分别提高了12%—112%和22%—143%.与CNPs相比,CNPs-HA和CNPs-NaAlg对Pb²⁺的吸附增加了21%—71%和23%—65%,对Cd²⁺的吸附增加了26%—45%和45%—91%.并且NPs和NPs-NOM对Pb²⁺和Cd²⁺的吸附符合Freundlich吸附模型.离子强度的增加抑制了NPs-HA/NaAlg和NPs对Pb²⁺和Cd²⁺的吸附,而pH的增加对NPs-HA/NaAlg和NPs吸附Pb²⁺和Cd²⁺起促进作用.     

改性多孔碳微球的制备及去除水中四溴双酚A的性能

为提高多孔碳微球对TBBPA的去除性能,采用氮掺杂、H₂O₂氧化和球磨对多孔碳微球进行表面改性,运用比表面积及孔隙度分析仪、傅里叶红外光谱（FT-IR）和X射线衍射仪（XPS）等方法表征改性前后多孔碳微球形貌、孔隙特征、官能团种类及含量和热稳定性等变化情况,通过吸附实验确定多孔碳微球的最佳改性方法,并探究吸附机理.结果表明,多孔碳微球、C-N、C-H₂O₂和C-球磨对TBBPA的最大吸附量分别为36.6、 43.1、 47.4、 58.35 mg·g^-1.吸附过程符合准二级动力学模型,Langmuir模型能够更好的描述多孔碳微球对TBBPA的吸附过程,主要为单分子层均匀化学吸附.其中C-球磨对TBBPA的吸附性能最佳,最大吸附量和吸附速率分别提高了1.6倍和2.9倍;球磨改性极大提高了碳材料的比表面积和含氧官能团,增加了吸附污染物的活性位点,强化了氢键和π-π电子供受体作用,且受pH和腐殖酸（HA）的影响较小,拓宽了环境适用范围.本研究以期为廉价碳材料去除有机污染物性能提供理论...     

Preparation of a novel anion exchange group modified hyper-crosslinked resin for the effective adsorption of both tetracycline and humic acid

A novel hyper-crosslinked resin (MENQ) modified with an anion exchange group was prepared using divinylbenzene (DVB) and methyl acrylate (MA) as comonomers via four steps: suspension polymerization, post-crosslinking, ammonolysis and alkylation reactions. The obtained resin had both a high specific surface area (793.34 m²·g^-1) and a large exchange capacity (strong base anion exchange capacity, SEC: 0.74 mmol·g^-1, weak base anion exchange capacity, WEC: 0.45 mmol·g^-1). XAD-4 was selected as an adsorbent for comparison to investigate the adsorption behavior of tetracycline (TC) and humic acid (HA) onto the adsorbents. The results revealed that MENQ could effectively remove both TC and HA. The adsorption capacity of XAD-4 for TC was similar to that of MENQ, but XAD-4 exhibited poor performance for the adsorption of HA. The adsorption isotherms of TC and HA were well-fitted with the Freundlich model, which indicated the existence of heterogeneous adsorption through cation-π bonding and π–π interactions. The optimal solution condition for the adsorption of TC was at a pH of 5–6, whereas the adsorption of HA was enhanced with increasing pH of the solution.     

Comparing the adsorption behaviors of Cd,Cu and Pb from water onto Fe-Mn binary oxide,MnO2 and FeOOH

The adsorption potential of FMBO, FeOOH, MnO₂ for the removal of Cd²⁺, Cu²⁺ and Pb²⁺ in aqueous systems was investigated in this study. Comparing to FMBO and FeOOH, MnO₂ offered a much higher removal capacity towards the three metal ions. The maximal adsorption capacity of MnO₂ for Cd²⁺, Cu²⁺ and Pb²⁺ were 1.23, 2.25 and 2.60 mmol·g^-1, respectively. And that for FMBO were 0.37, 1.13, and 1.18 mmol·g^-1 and for FeOOH were 0.11, 0.86 and 0.48 mmol·g^-1, respectively. The adsorption behaviors of the three metal ions on the three adsorbents were all significantly affected by pH values and heavy metal removal efficiency increased with pH increased. The Langmuir and Freundlich adsorption models were used to describe the adsorption equilibrium of the three metal ions onto the three adsorbents. Results showed that the adsorption equilibrium data fitted well to Langmuir isotherm and this indicated that adsorption of metal ions occurred on the three metal oxides adsorbents limited to the formation of a monolayer. More negative charged of MnO₂ surface than that of FMBO and FeOOH could be ascribed by lower pH_iep of MnO₂ than that of FMBO and FeOOH and this could contribute to more binding sites on MnO₂ surface than that of FMBO and FeOOH. The higher metal ions uptake by MnO₂ than FMBO and FeOOH could be well explained by the surface charge mechanism.     

Fe3O4@SA/Ce微球的表征及对染料的吸附特性

以天然高分子化合物海藻酸钠(sodium alginate,SA)为骨架,结合磁性Fe₃O₄和稀土铈离子Ce(Ⅲ)通过溶液反应制备出一种新型的磁性海藻酸铈复合微球(Fe₃O₄@SA;Ce).采用X射线衍射(XRD)、孔结构比表面积分析(BET)、扫描电子显微镜(SEM)、红外光谱(FT-IR)及振动样品强磁计(VSM)对Fe₃O₄@SA;Ce的结构进行了表征,并以直接桃红12B(direct red 12B,DR 12B)和直接橙S(direct orange S,DO S)两种染料为吸附对象,探讨了Fe₃O₄@SA;Ce的吸附剂性能、吸附动力学和热力学.结果表明,Fe₃O₄@SA;Ce对室温下自然pH染料溶液中DR 12B和DO S均表现出良好的吸附效果,吸附量分别可达464 mg·g^-1和730 mg·g^-1.在不同温度下(298、313、328 K),Fe₃O₄@SA;Ce对DR 12B和DO S的吸附过程均可用拟二级吸附动力学方程准确描述.通过等温吸附研究,发现Fe₃O₄@SA;Ce对两种染料的等温吸附较好地符合Freundlich模型.各种表征结果表明,SA与Ce(Ⅲ)和Fe₃O₄交联反应后生成的Fe₃O₄@SA;Ce凝胶球表面有大量深浅不一的褶皱沟纹,形貌发生了显著变化.作为一种绿色环保、制备方法简单、可高效吸附的磁性高分子复合吸附剂,Fe₃O₄@SA;Ce对高浓度染料具有很好的吸附效果,期望能够在染料废水处理中得到广泛应用.     

Removal of fluoride from water using titanium-based adsorbents

Three adsorbents including TiO₂, Ti-Ce, and Ti-La hybrid oxides were prepared to remove fluoride from aqueous solution. The Ti-Ce and Ti-La hybrid adsorbents obtained by the hydrolysis-precipitation method had much higher sorption capacity for fluoride than the TiO₂ adsorbent prepared through hydrolysis. Rare earth (Ce and La) oxides and TiO₂ exhibited a synergistic effect in the hybrid adsorbents for fluoride sorption. The sorption equilibrium of fluoride on the three adsorbents was achieved within 4 h, and the pseudo-second-order model described the sorption kinetics well. The sorption isotherms fitted the Langmuir model well, and the adsorption capacities of fluoride on the Ti-Ce and Ti-La adsorbents were about 9.6 and 15.1 mg·g^-1, respectively, at the equilibrium fluoride concentration of 1.0 mg·L^-1, much higher than the 1.7 mg·g^-1 on the TiO₂. The sorption capacities of fluoride on the three adsorbents decreased significantly when the solution pH increased from 3 to 9.5. The electrostatic interaction played an important role in fluoride removal by the three adsorbents, and Fourier transform infrared (FTIR) analysis indicated that the hydroxyl groups on the adsorbent surface were involved in fluoride adsorption.     

Preparation of a permanent magnetic hypercrosslinked resin and assessment of its ability to remove organic micropollutants from drinking water

A rapid and effective method based on a novel permanent magnetic hypercrosslinked resin W150 was proposed for the removal of organic micropollutants in drinking water. W150 was prepared by suspension and post-crosslinking reaction and found to possess a high specific surface area of 1149.7 m²·g^-1, a small particle size of 50 μm to 100 μm, and a saturation magnetization as high as 8 emu·g^-1. W150 was used to eliminate nitrofurazone (NFZ) and oxytetracycline (OTC) from drinking water compared with commercial adsorbents XAD-4 and F400D. The adsorption kinetics of NFZ and OTC onto the three adsorbents well fitted the pseudo-second-order equation (r>0.972), and the adsorption isotherms were all well described by the Freundlich equation (r>0.851). Results showed that the reduction in adsorbent size and the enlargement in sorbent pores both accelerated adsorption. Moreover, the effect of particle size on adsorption was more significant than that of pore width. Given that the smallest particle size and the highest specific surface area were possessed by W150, it had the fastest adsorption kinetics and largest adsorption capacity for NFZ (180 mg·g^-1) and OTC (200 mg·g^-1). For the adsorbents with dominant micropores, the sorption of large-sized adsorbates decreased because of the inaccessible micropores. The solution pH and ionic strength also influenced adsorption.     

Fabrication,characterization and evaluation of mesoporous activated carbons from agricultural waste: Jerusalem artichoke stalk as an example

This work explores the feasibility of Jerusalem artichoke stem (JAS), an agricultural waste, as an alternative precursor for fabrication of mesoporous activated carbon (MAC) via conventional ZnCl₂ activation. The as-prepared JAS-MACs were characterized by thermogravimetric, nitrogen gas adsorption isotherm and high resolution scanning electron microscopy analysis. The interacting effects of chemical dosage, activation temperature and time on the mesoporosity, mesopore volume and carbon yield were investigated, and further optimized by response surface methodology (RSM). The Brunauer-Emmett-Teller surface area, mesoporosity and mesopore volume of the JAS-MAC prepared under optimum condition were identified to be 1631 m²·g^-1, 90.16% and 1.11 cm³·g^-1, respectively. Compared with commercial activated carbons, this carbon exhibited a comparable monolayer adsorption capacity of 374.5 mg·g^-1 for Methylene Blue dye. The findings suggest that RSM could be an effective approach for optimizing the pore structure of fabricated activated carbons.     

Reduction of hexavalent chromium with scrap iron in a fixed bed reactor

The reduction of hexavalent chromium by scrap iron was investigated in continuous long-term fixed bed system. The effects of pH, empty bed contact time (EBCT), and initial Cr(VI) concentration on Cr(VI) reduction were studied. The results showed that the pH, EBCT, and initial Cr(VI) concentration significantly affected the reduction capacity of scrap iron. The reduction capacity of scrap iron were 4.56, 1.51, and 0.57 mg Cr(VI)·g^-1 Fe⁰ at pH 3, 5, and 7 (initial Cr(VI) concentration 4 mg·L^-1, EBCT 2 min, and temperature 25°C), 0.51, 1.51, and 2.85 mg Cr(VI)·g^-1 Fe⁰ at EBCTs of 0.5, 2.0, and 6.0 min (initial Cr(VI) concentration 4 mg·L^-1, pH 5, and temperature 25°C), and 2.99, 1.51, and 1.01 mg Cr(VI)·g^-1 Fe⁰ at influent concentrations of 1, 4, and 8 mg·L^-1 (EBCT 2 min, pH 5, and temperature 25°C), respectively. Fe(total) concentration in the column effluent continuously decreased in time, due to a decrease in time of the iron corrosion rate. The fixed bed reactor can be readily used for the treatment of drinking water containing low amounts of Cr(VI) ions, although the hardness and humic acid in water may shorten the lifetime of the reactor, the reduction capacity of scrap iron still achieved 1.98 mg Cr⁶⁺·g^-1 Fe. Scanning electron microscope equipped with energy dispersion spectrometer and X-ray diffraction were conducted to examine the surface species of the scrap iron before and after its use. In addition to iron oxides and hydroxide species, iron-chromium complex was also observed on the reacted scrap iron.     

pH值对有机蒙脱土吸附苯酚的影响

利用十六烷基三甲基溴化铵(HDTMA)改性的蒙脱土来处理含酚废水,了解pH值对有机蒙脱土吸附苯酚的影响．结果表明：不论是酸性还是碱性含酚水溶液,加入有机蒙脱土后其pH值都趋向中性,因此,有机蒙脱土对酸碱具有良好的缓冲能力．在相同pH条件下,吸附在有机蒙脱土上苯酚的数量随着其改性量的提高而增加．在碱性条件下,被有机蒙脱土吸附的苯酚可以发生解吸,pH值愈高,有机蒙脱土吸附的苯酚数量愈少,因此,吸附在有机蒙脱上上的苯酚在碱性条件下是不稳定的．通过碱再生有机蒙脱土又能吸附水溶液中的苯酚,但是其吸附苯酚的能力有所下降．     

One-pot preparation of graphene oxide magnetic nanocomposites for the removal of tetrabromobisphenol A

A simple solvothermal method was used to prepare monodisperse magnetite (Fe₃O₄) nanoparticles attached onto graphene oxide (GO) sheets as adsorbents to remove tetrabromobisphenol A (TBBPA) from an aqueous solution. These Fe₃O₄/GO (MGO) nanocomposites were characterized by transmission electron microscopy. The adsorption capacity at different initial pH, contact duration, and temperature were evaluated. The kinetics of adsorption was found to fit the pseudo-second-order model perfectly. The adsorption isotherm well fitted the Langmuir model, and the theoretical maximum of adsorption capacity calculated by the Langmuir model was 27.26 mg?g^-1. The adsorption thermodynamics of TBBPA on the MGO nanocomposites was determined at 303 K, 313 K, and 323 K, respectively. The results indicated that the adsorption was spontaneous and endothermic. The MGO nanocomposites were conveniently separated from the media by an external magnetic field within several seconds, and then regenerated in 0.2 M NaOH solution. Thus, the MGO nanocomposites are a promising candidate for TBBPA removal from wastewater.