Water quality changes of a closed underground coal mine in Korea

The objective of this study was to assess the changes in mine water quality as an underground mine flooded from July 2005 to October 2008. The effect of air injection with a blower into the water was used to evaluate the potential to convert ferrous to ferric iron and to provide in situ treatment and precipitation. Mine flooding averaged 31 cm/day with a linear shape until November 2007, when it flattened out due to outflow. During flooding, mine water pH remained around 6, but Eh shifted from 200 to −150 mV. After the mine water level stabilized, contents of elements such as Fe and SO₄ tended to decrease as time passed. Air was injected by diffusers (150 L/min/each) at three different depths of 2, 3, and 5 m below the water level in the shaft. Dissolved oxygen eventually increased to 4 or 5 mg/L depending on the depth of the diffusers. Aeration caused conversion of ferrous iron to ferric iron and about 30 mg/l of iron was removed from the mine water. Therefore, air injection shows potential as a semi-active treatment or part of conventional treatment to precipitate iron in the mine pool.     

Occupational exposure to rubber vulcanization products during repair of rubber conveyor belts in a brown coal mine

Several hundred chemical compounds were found in workroom environments in the rubber industry, but most of the published exposure data relate to the production of tyres; information from the "non-tyre" sections are very limited, if any. This study was carried out to identify chemical substances and measure their air concentrations in the repair shop of a brown coal mine in which damaged rubber conveyor belts were repaired. GC-MS and HPLC analysis of stationary air samples resulted in identification of aliphatic and aromatic hydrocarbons to C12, PAHs, alcohols, phenols, ketones, heterocyclic nitrogen and sulfur compounds. Quantitative evaluation of occupational exposure included determination of organic compound vapours collected on charcoal (GC-MSD), polycyclic aromatic hydrocarbons (HPLC), N-nitrosoamines and other amines (GC-NPD) and DNPH derivatives of aldehydes (HPLC) in the breathing zone of workers representing all job titles. The concentrations of investigated compounds were very low. Carcinogenic substances: N-nitrosoamines, benzene, PAHs were not present in workroom air in concentrations exceeding limits of detection of the analytical methods being applied; concentrations of methylisobutylketone, tetrachloroethylene, naphtha, aromatic hydrocarbons, phthalates and aldehydes were much lower than the respective occupational exposure limit values. The results indicate much lower exposure than that reported in the production of tyres and other fabricated rubber products.     

Ecological risk assessment of open coal mine area

The coal mine areas in China have the serious conflicts between resources exploitation and ecology safety, therefore the coal mine ecological risk assessment is an important problem which relates to the sustainability of coal mines to regions and the whole country. In this study, open coal mine area serves as researching object, heavy metals, soil erosion and coast are screened out as risk resources, soil wireworm as the receiver of heavy metals risk, biotope ecosystem as the receiver of soil erosion and coast risk; ecological indexes are calculated with species background index, biological diversity index and natural degree index, ecological friability indexes are calculated with soil fertility index, plant coverage, plant species diversity index, soil wireworm index and maturity index, and the typical coal mine area assessment indexes system is established. In addition, the regional ecological risk assessment is conducted on the friable ecological system of Fuxin Haizhou open coal mine area. Examples are researched of Haizhou open coal mine, the coal mine risk distribution is established, and foundations are provided for the administrative decision-making.     

Assessment of respirable dust exposures in an opencast coal mine

All major opencast mining activities produce dust. The major operations that produce dust are drilling, blasting, loading, unloading, and transporting. Dust not only deteriorates the environmental air quality in and around the mining site but also creates serious health hazards. Therefore, assessment of dust levels that arise from various opencast mining operations is required to prevent and minimize the health risks. To achieve this objective, an opencast coal mining area was selected to generate site-specific emission data and collect respirable dust measurement samples. The study covered various mining activities in different locations including overburden loading, stock yard, coal loading, drilling, and coal handling plant. The dust levels were examined to assess miners' exposure to respirable dust in each of the opencast mining areas from 1994 to 2005. The data obtained from the dust measurement studies were evaluated by using analysis of variance (ANOVA) and the Tukey-Kramer procedure. The analyses were performed by using Minitab 14 statistical software. It was concluded that, drilling operations produce higher dust concentration levels and thus, drill operators may have higher incidence of respiratory disorders related to exposure to dust in their work environment.     

PM10 in the ambient air of Chandrapur coal mine and its comparison with other environments

This study compares the ambient air particulate matter (PM10) data of 15 different coal mine environments. For most of these mine environments, the monitoring was carried out by different researchers using respirable dust sampler (RDS) that separates PM10 by centrifugal inertial separation. At two sites — Padmapur and Ghugus (Chandrapur, Maharashtra, India) — mass inertial impaction-based sampler was used for PM10 monitoring. It is observed that the spatiotemporal average value of ambient air PM10 monitored using mass inertial impactor reports relatively higher values (240–372 μg/m³) compared to those monitored using RDS (<227 μg/m³). In order to realize the severity of mine area pollution, it is compared with PM10 values found in an urban area (Delhi, India). It is found that PM10 values in Delhi (using mass inertial impactor) are much higher (300–400 μg/m³) than those reported for the mine environment. The data seems to indicate that the mine environment is relatively cleaner than urban air and therefore raises doubt about the appropriateness of using either mass impactor or RDS for PM10 sampling.     

Blood levels of cadmium and lead in residents near abandoned metal mine areas in Korea

We analyzed national data on blood lead levels (BLL) and blood cadmium levels (BCL) in residents living near 38 abandoned metal mining areas (n?=?5,682, 18–96 years old) in Korea that were collected by the first Health Effect Surveillance for Residents in Abandoned Metal mines (HESRAM) from 2008 to 2011. The geometric mean BCL and BLL were 1.60 μg/L (95 % CI?=?1.57–1.62 μg/L) and 2.87 μg/dL (95 % CI?=?2.84–2.90 μg/dL), respectively, notably higher than levels in the general population in Korea and other countries. We found significantly higher BLL and BCL levels in people living within 2 km of an abandoned metal mine (n?=?3,165, BCL?=?1.87 μg/L, BLL?=?2.91 μg/dL) compared to people living more than 2 km away (n?=?2,517, BCL?=?1.31 μg/L, BLL?=?2.82 μg/dL; P?<?0.0001) and to the general population values reported in the literature.     

Indoor air pollution levels in public buildings in Thailand and exposure assessment

Levels of pollutants including PM2.5 and PM2.5 composition (black carbon and water soluble ions), SO(2), NO(2), CO, CO(2), and BTEX (benzene, toluene, ethylbenzene, xylene) were monitored for indoor and outdoor air at a university campus and a shopping center, both located in the Northern suburb of Bangkok. Sampling was done during December 2005-February 2006 on both weekdays and weekends. At the university, indoor monitoring was done in two different air conditioned classrooms which shows the I/O ratios for all pollutants to be below 0.5-0.8 during the weekends. However, on weekdays the ratios for CO(2) and most detected BTEX were above 1.0. The concept of classroom occupancy was defined using a function of the student number in a lecture hour and the number of lecture hours per day. Classroom 2, which had a higher occupancy than classroom 1, was characterized by higher concentrations of most pollutants. PM2.5 was an exception and was higher in classroom 1 (37 microg/m(3), weekdays) as compared to classroom 2 (26 microg/m(3), weekdays) which was likely linked to the dust resuspension from the carpeted floor in the former. Monitoring was also done in the shopping mall at three different sites. Indoor pollutants levels and the I/O ratios at the shopping mall were higher than at the university. Levels of all pollutants measured at the car park, except for toluene and CO(2), were the highest. I/O ratios of the pollutants at the mall were above 1.0, which indicates the relatively higher influence of the indoor sources. However, the black carbon content in PM2.5 outdoor is higher than indoor, which suggest the important contribution from outdoor combustion sources such as the traffic. Major sources of outdoor air pollution in the areas were briefly discussed. Exposure modeling was applied using the time activity and measured pollutant concentrations to assess the exposure of different groups of people in the study areas. High exposure to PM2.5, especially for the people working in the mall, should be of health effect concern.     

Heavy metal accumulation and ecosystem engineering by two common mine site-nesting ant species: implications for pollution-level assessment and bioremediation of coal mine soil

The present study focuses on the abundance, heavy metal content, and the impact of ecosystem engineering activities of two coal mine site-inhabiting ant species, Cataglyphis longipedem and Camponotus compressus. The abundance of Ct. longipedem increased while that of C. compressus decreased, with increasing soil pollution. Correspondence analysis reveals a close association between soil heavy metal concentrations and Ct. longipedem abundance, but this association is lacking in the case of C. compressus. Cataglyphis ants which occupy stress-characterized niches appear to be pre-adapted to tolerate heavy metal pollution. Higher concentrations of Zn and Mn in Ct. longipedem may contribute to the strengthening of the cuticular structures, necessary for nest excavation in the hard, arid soil and for single load carrying. C. compressus ants appear to be pollution sensitive. Their higher Fe content may be related to metal uptake via plant-derived liquids and species-specific regulatory mechanisms. The metal pollution index and biota-to-soil accumulation factors, calculated by using the ant body metal content of the two species, indicate an overall decrease of soil heavy metal concentrations with increase of the site age, which reflects the degree of pollution related to the mine site age. The concentrations of total and available heavy metals (Fe, Zn, Mn, Pb, and Cu) were significantly lower in the ant nest debris soil as compared to the reference soil. The results of the present study highlight the role of ants as bioindicators and in bioremediation of contaminated soil.     

Equivalency of a personal dust monitor to the current United States coal mine respirable dust sampler

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% confidence that greater than 95% of individual PDM measurements fall within +/-25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr-Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed specifically to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A stratified random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I.=(1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler-equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m(-3).     

Determination of contaminant levels and remediation efficacy in groundwater at a former in situ recovery uranium mine

There has been increasing interest in uranium mining in the United States via in situ recovery techniques. One of the main environmental concerns with in situ uranium mining is the potential for spreading groundwater contamination. There is a dearth of detailed analysis and information regarding the outcome of in situ uranium mine remediation to ascertain the environmental impacts. Regulatory measurements performed at a Wyoming in situ uranium mine were collected and analysed to ascertain the efficacy of remediation and potential long term environmental impact. Based on the measurements, groundwater sweeping followed by reverse osmosis (RO) treatment proved to be a highly efficient method of remediation. However, injection of a reductant in the form of H(2)S after groundwater sweeping and RO did not further reduce the aqueous concentration of U, Mn, or Fe. Low concentrations of target species at monitoring wells outside the mined area appear to indicate that in the long term, natural attenuation is likely to play a major role at reductively immobilizing residual (after remediation) concentrations of U(VI) thus preventing it from moving outside the mined area. Our analysis indicates the need for additional monitoring wells and sampling in conjunction with long term monitoring to better understand the impacts of the different remediation techniques.     

An analytical model for the assessment of pesticide exposure levels in soils and groundwater

The movement and degradation of pesticide residues in soils and groundwater are complex processes affected by soil physical, (bio)chemical, and hydrogeological properties, climatic conditions, and agricultural practices. This work presents a physically-based analytical model suitable for long-term predictions of pesticide concentrations in groundwater. The primary interest is to investigate the impact of soil environment, related physical and (bio)chemical processes, especially, volatilization, crop uptake, and agricultural practices on long-term vulnerability of groundwater to contamination by pesticides. The soil is separated into root and intermediate vadose zones, each with uniform properties. Transport in each soil zone is modeled on the basis of complete mixing, by spatial averaging the related point multiphase-transport partial differential equation (i.e., linear-reservoir models). Transport in the aquifer, however, is modeled by a two-dimensional advection-dispersion transport equation, considering adsorption and first-order decay rate. Vaporization in the soil is accounted for by assuming liquid-vapor phase partitioning using Henry's law, and vapor flux (volatilization) from the soil surface is modeled by diffusion through an air boundary layer. Sorption of liquid-phase solutes by crops is described by a linear relationship which is valid for first-order (passive) crop uptake. The model is applied to five pesticides (atrazine, bromacil, chlordane, heptachlor, and lindane), and the potential for pesticide contamination of groundwater is investigated for sandy and clayey soils. Simulation results show that groundwater contamination can be substantially reduced for clayey soil environments, where bio(chemical) degradation and volatilization are most efficient as natural loss pathways for the pesticides. Also, uptake by cross can be a significant mechanism for attenuating exposure levels in ground-water especially in a sandy soil environment, and for relatively persisting pesticides. Further, simulations indicate that changing agricultural practices can have a profound effect on vulnerability of groundwater to mobile and relatively persisting pesticides.     

Monitoring and assessment of daily exposure of roadside workers to traffic noise levels in an Asian city: a case study of Bangkok streets

Four noise monitoring sites were strategically established to evaluate average noise level and audiometric assessment at various traffic zones of Bangkok Metropolitan Region (BMR). During the monitoring period, noise levels were found to be 72.8–83.0 dBA during day time and 59.5–74.5 dBA during night time. The finding also indicated that traffic noise levels depend on distance from roadside, diurnal variation and character of the traffic and street configuration. Audiometric measurement of 4000 persons was carried by four major hospitals in Bangkok to study the relationship between traffic noise exposure of groups of people working in the streets and hearing loss. Four different categories of occupational people, i.e., drivers, street vendors, traffic officers and dwellers were selected and were further classified into age groups (16–25, 26–35, 36–45 and 46–55 years old) to monitor the traffic noise induced hearing loss throughout their everyday lives. The control group was deliberately chosen to screen out the effects of traffic noise. According to the audiometric investigation, it was revealed that hearing capacity of the daily noise exposure groups living in the three urban sites (Yaowarat Road, Din Daeng Road and Ratchaprarop Road) were noticeably poorer than those who were living in suburban site (Phahonyothin Road). It was noted that the mean hearing threshold level (HTL) of the 16–25 years old groups were found to have better hearing capacity than those older adults of 46–55 years old. In particular the mean HTL dropped at the frequency of 4000 Hz. Among the occupational population who were living in the urban monitoring sites, the driver groups were found to have the highest risk of traffic noise induced hearing loss.     

Chemical speciation in mining affected waters: the case study of Asarel-Medet mine

The inorganic chemical species in Maresh and Luda Yana rivers affected by the Cu– Mo Asarel-Medet mine, Bulgaria were determined during a low-flow and a high-flow period. The mining activities, the weathering and the oxidation processes strongly influenced the physicochemical processes in the whole water system. The main pollution source was a small lake receiving the acid effluents of the mining activities. High levels of SO₄ ^2???, Cu, Mg, Al, Mn and Fe were determined at the mining polluted and affected stations. Cu^2?+? and CuCO₃ ⁰ species (1:1) were present in the reference waters and Cu^2?+? and CuSO₄ ⁰ species (1:1) in the polluted and affected waters; Cu^2?+? species was dominating downstream. Me^2?+? followed by $\rm{MeSO}_{4}^{\kern3pt{0}}$ (Me = Mn, Zn, Cd and Pb), $\rm{PbCO}_{3}^{\kern3pt{0}}$ and $\rm{PbHCO}_{3}^{\kern3pt{+}}$ species as well as $\rm{Fe(OH)}_{2}^{\kern3pt{+}}$ , $\rm{Al(OH)}_{4}^{\kern3pt{-}}$ , $\rm{Al(OH)}_{2}^{\kern3pt{+}}$ , $\rm{Al(OH)}_{3}^{\kern3pt{0}}$ were prevailing in the system. $\rm{MeSO}_{4}^{\kern3pt{+}}$ and $\rm{Me(SO}_{4})_{2}^{\kern3pt{-}}$ (Me = Fe, Al), $\rm{Me(SO}_{4})_{2}^{\kern3pt{2-}}$ (Me = Zn, Cd and Pb), $\rm{Me(SO}_{4})_{3}^{\kern3pt{4-}}$ (Me = Zn, Cd) and $\rm{Cd(SO}_{4})_{4}^{\kern3pt{6-}}$ species polluted and affected waters. The major elements K and Na were mainly Me^?+? species, whereas Ca and Mg were Me^2?+? and $\rm{MeSO}_{4}^{\kern3pt{0}}$ species in different ratios. The concentration of concentration of $\rm{NO}_{2}^{\kern3pt{-}}$ , $\rm{NO}_{3}^{\kern3pt{-}}$ and $\rm{NH}_{4}^{\kern3pt{+}}$ species as well as complex phosphorous species such as H₂ $\rm{PO}_{4}^{\kern3pt{-}}$ , $\rm{FeHPO}_{4}^{\kern3pt{+}}$ , $\rm{HPO}_{4}^{\kern4pt{2-}}$ , $\rm{CaPO}_{4}^{\kern3pt{-}}$ , $\rm{CaHPO}_{4}^{\kern3pt{0}}$ and $\rm{MgHPO}_{4}^{\kern3pt{0}}$ were also calculated. The trace element concentrations decreased downstream due to dilution, sorption processes and precipitation, but the percentage of free metal species, which are more toxic, increased. An exception was iron and aluminum of which the dominant hydroxy colloidal and sulphate species were easily incorporated into the suspended phase.     

Determination and evaluation of hexavalent chromium in power plant coal combustion by-products and cost-effective environmental remediation solutions using acid mine drainage

The chromium species leaching from a coal combustion fly ash landfill has been characterized as well as a novel approach to treat leachates rich in hexavalent chromium, Cr(VI), by using another natural waste by-product, acid mine drainage (AMD), has been investigated during this study. It is observed that as much as 8% (approximately 10 microg g(-1) in fly ash) of total chromium is converted to the Cr(VI) species during oxidative combustion of coal and remains in the resulting ash as a stable species, however, it is significantly mobile in water based leaching. Approximately 1.23 +/- 0.01 microg g(-1) of Cr(VI) was found in the landfill leachate from permanent deposits of aged fly ash. This study also confirmed the use of AMD, which often is in close proximity to coal combustion by-product landfills, is an extremely effective and economical remediation option for the elimination of hexavalent chromium in fly ash generated leachate. Speciated isotope dilution mass spectrometry (SIDMS), as described in EPA Method 6800, was used to analytically evaluate and validate the field application of the ferrous iron and chromate chemistry in the remediation of Cr(VI) runoff.     

An indicative method for determination of the most hazardous changes in slopes of the subsidence basins in underground coal mining area in Ostrava (Czech Republic)

Considering growing population and decreasing mineral resource reserves, the issue of undermining has been and shall remain very topical. This study aims to identify the mutual connections between mined out panels of a deposit and the final manifestations on the ground surface related to deep black coal mining. On the grounds of the identified connections, the study describes a method to simplify a common evaluation of undermined areas according to building site categories. Within the study, a demarcation of the areas was conducted in two localities in Czech Republic influenced by the effects of undermining in the Upper-Silesian Basin. In the allotment of the CSM Mine, an area unsuitable for founding structures was defined from the centre of the worked out workings to the distance of 175 m from the panel's edge, for which the corresponding break angle is 78.3°. Similarly, in the allotment of the Paskov Mine, an area unsuitable for founding structures was determined to the distance of 500 m from the panel's edge, for which the corresponding break angle is 50.2°. This demarcation may be implemented prior to deposit mining being aware of several physical-mechanical parameters of rocks in the deposit's overburden. Having mined out a particular section of a deposit, it is recommended to verify the values of break angle using the method described herein. The study may be applied as a relatively fast and effective method to evaluate future land use for planning.     

Coal mining and the resource community cycle: A longitudinal assessment of the social impacts of the Coppabella coal mine

Two social impact assessment (SIA) studies of Central Queensland's Coppabella coal mine were undertaken in 2002–2003 and 2006–2007. As ex post studies of actual change, these provide a reference point for predictive assessments of proposed resource extraction projects at other sites, while the longitudinal element added by the second study illustrates how impacts associated with one mine may vary over time due to changing economic and social conditions. It was found that the traditional coupling of local economic vitality and community development to the life cycle of resource projects—the resource community cycle—was mediated by labour recruitment and social infrastructure policies that reduced the emphasis on localised employment and investment strategies, and by the cumulative impacts of multiple mining projects within relative proximity to each other. The resource community cycle was accelerated and local communities forced to consider ways of attracting secondary investment and/or alternative industries early in the operational life of the Coppabella mine in order to secure significant economic benefits and to guard against the erosion of social capital and the ability to cope with future downturns in the mining sector.     

SPME-based air sampling method for inhalation exposure assessment studies: case study on perchlorethylene exposure in dry cleaning

Exposure to perchlorethylene, especially for dry cleaning workers and for people living near dry cleaning shops, could lead to several diseases and disorders. This study examines the value of solid-phase microextraction (SPME) for sampling perchlorethylene in the atmosphere of dry cleaning shops. Carboxen/polydimethylsiloxane (CAR/PDMS) in 0.5-cm retracted mode was selected. There were no significant differences between sampling rates at different temperatures (range of 20 to 30 °C) and air velocities (2 to 50 cm/s). On the opposite, relative humidity (RH) had a significant effect on sampling rates. Method reproducibility was realized in the laboratory and field conditions and was 6.2 % and 7 to 11 %, respectively. Repeatability was also determined as 8.9 %. Comparison of the results according to the American Industrial Hygiene Association exposure assessment strategy showed the SPME sampler yields more conservative results in comparison with traditional standard method.     

A study of exposure standards in Russia and the role of occupational hygiene

This paper is the result of an investigation carried out in February 1997, which set out to learn about the development and application of occupational health standards, and in turn approaches to occupational environmental monitoring, in Russia, and to see how these were similar to, or different from, what takes place in other countries. The enquiry involved face-to-face meetings with senior Russian occupational health scientists and officials. It was confirmed that Russian occupational exposure standards are very stringent and provide a very high level of protection of workers. However, they are difficult to enforce, and it is suggested that the development of a strong and distinctive occupational hygiene discipline and profession in Russia would provide a "bridge" to enable more effective implementation and interpretation of those standards.