Effects of improved spatial and temporal modeling of on-road vehicle emissions

Numerous emission and air quality modeling studies have suggested the need to accurately characterize the spatial and temporal variations in on-road vehicle emissions. The purpose of this study was to quantify the impact that using detailed traffic activity data has on emission estimates used to model air quality impacts. The on-road vehicle emissions are estimated by multiplying the vehicle miles traveled (VMT) by the fleet-average emission factors determined by road link and hour of day. Changes in the fraction of VMT from heavy-duty diesel vehicles (HDDVs) can have a significant impact on estimated fleet-average emissions because the emission factors for HDDV nitrogen oxides (NOx) and particulate matter (PM) are much higher than those for light-duty gas vehicles (LDGVs). Through detailed road link-level on-road vehicle emission modeling, this work investigated two scenarios for better characterizing mobile source emissions: (1) improved spatial and temporal variation of vehicle type fractions, and (2) use of Motor Vehicle Emission Simulator (MOVES2010) instead of MOBILE6 exhaust emission factors. Emissions were estimated for the Detroit and Atlanta metropolitan areas for summer and winter episodes. The VMT mix scenario demonstrated the importance of better characterizing HDDV activity by time of day, day of week, and road type. More HDDV activity occurs on restricted access road types on weekdays and at nonpeak times, compared to light-duty vehicles, resulting in 5-15% higher NOx and PM emission rates during the weekdays and 15-40% lower rates on weekend days. Use of MOVES2010 exhaust emission factors resulted in increases of more than 50% in NOx and PM for both HDDVs and LDGVs, relative to MOBILE6. Because LDGV PM emissions have been shown to increase with lower temperatures, the most dramatic increase from MOBILE6 to MOVES2010 emission rates occurred for PM2.5 from LDGVs that increased 500% during colder wintertime conditions found in Detroit, the northernmost city modeled.     

Scattering cross-section emission factors for visibility and radiative transfer applications: military vehicles traveling on unpaved roads

Emission factors for particulate matter (PM) are generally reported as mass emission factors (PM mass emitted per time or activity) as appropriate for air quality standards based on mass concentration. However, for visibility and radiative transfer applications, scattering, absorption, and extinction coefficients are the parameters of interest, with visibility standards based on extinction coefficients. These coefficients (dimension of inverse distance) equal cross-section concentrations, and, therefore, cross-section emission factors are appropriate. Scattering cross-section emission factors were determined for dust entrainment by nine vehicles, ranging from light passenger vehicles to heavy military vehicles, traveling on an unpaved road. Each vehicle made multiple passes at multiple speeds while scattering and absorption coefficients, wind velocity and dust plume profiles, and additional parameters were measured downwind of the road. Light absorption of the entrained PM was negligible, and the light extinction was primarily caused by scattering. The resulting scattering cross-section emission factors per vehicle kilometer traveled (vkt) range from 12.5 m2/vkt for a slow (16 km/ hr), light (1176 kg) vehicle to 3724 m2/vkt for a fast (64 km/hr), heavy (17,727 kg) vehicle and generally increase with vehicle speed and mass. The increase is approximately linear with speed, yielding emission factors per vkt and speed ranging from 4.2 m2/(vkt km/hr) to 53 m2/(vkt km/hr). These emission factors depend approximately linearly on vehicle mass within the groups of light (vehicle mass < or =3100 kg) and heavy (vehicle mass >8000 kg) vehicles yielding emission factors per vkt, speed, and mass of 0.0056 m2/(vkt km/hr kg) and 0.0024 m2/(vkt km/hr kg), respectively. Comparison of the scattering cross-section and PM mass emission factors yields average mass scattering efficiencies of 1.5 m2/g for the light vehicles and of 0.8 m2/g for the heavy vehicles indicating that the heavy vehicles entrain larger particles than the light vehicles.     

Size and composition distributions of particulate matter emissions: part 2--heavy-duty diesel vehicles

Particulate matter (PM) emissions from heavy-duty diesel vehicles (HDDVs) were collected using a chassis dynamometer/dilution sampling system that employed filter-based samplers, cascade impactors, and scanning mobility particle size (SMPS) measurements. Four diesel vehicles with different engine and emission control technologies were tested using the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) 5 mode driving cycle. Vehicles were tested using a simulated inertial weight of either 56,000 or 66,000 lb. Exhaust particles were then analyzed for total carbon, elemental carbon (EC), organic matter (OM), and water-soluble ions. HDDV fine (< or =1.8 microm aerodynamic diameter; PM1.8) and ultrafine (0.056-0.1 microm aerodynamic diameter; PM0.1) PM emission rates ranged from 181-581 mg/km and 25-72 mg/km, respectively, with the highest emission rates in both size fractions associated with the oldest vehicle tested. Older diesel vehicles produced fine and ultrafine exhaust particles with higher EC/OM ratios than newer vehicles. Transient modes produced very high EC/OM ratios whereas idle and creep modes produced very low EC/OM ratios. Calcium was the most abundant water-soluble ion with smaller amounts of magnesium, sodium, ammonium ion, and sulfate also detected. Particle mass distributions emitted during the full 5-mode HDDV tests peaked between 100-180 nm and their shapes were not a function of vehicle age. In contrast, particle mass distributions emitted during the idle and creep driving modes from the newest diesel vehicle had a peak diameter of approximately 70 nm, whereas mass distributions emitted from older vehicles had a peak diameter larger than 100 nm for both the idle and creep modes. Increasing inertial loads reduced the OM emissions, causing the residual EC emissions to shift to smaller sizes. The same HDDV tested at 56,000 and 66,000 lb had higher PM0.1 EC emissions (+22%) and lower PM0.1 OM emissions (-38%) at the higher load condition.     

隧道实验测定南京市机动车PM_（10）排放因子

选取南京城市隧道进行机动车PM10平均排放因子的测试研究。采用质量平衡模型和多元线性回归方法计算了4种车型PM10的综合排放因子。结果表明：隧道内机动车PM10平均排放因子为0.347±0.100 g/（km·辆）;大型车的PM10排放因子远高于其他车型的排放因子,其次是中型车和摩托车,小型车最小,其综合排放因子分别为1.440 g/（km·辆）、0.850 g/（km·辆）、0.790 g/（km·辆）和0.320 g/（km.辆）;在车速相似的情况下,本隧道实验所测机动车的PM10排放因子与国内隧道实验结果相仿,却远大于国外隧道实验结果。     

Comparison of emission factors for road traffic from a tunnel study (Gubrist tunnel,Switzerland) and from emission modeling

The emission factors of NO_x, VOC and CO of a road tunnel study performed in September 1993 in the Gubrist tunnel, close to Zürich (Switzerland) are compared with results of emission calculations based on recent results of dynamometric test measurements. The emission calculations are carried out with a traffic emission model taking into account the detailed composition of the vehicle fleet in the tunnel, the average speed and the gradient of the road and the special aerodynamics in a tunnel. With the exception of NO_x emission factors for heavy duty vehicles no evidence for a discrepancy between the results of the tunnel study and the emission modeling was found. The measured emission factors of individual hydrocarbons of light duty vehicles were in good agreement with the expectations for most components.     

Nitrous oxide emissions from light duty vehicles

Nitrous oxide (N₂O) emissions measurements were made on light duty gasoline and light duty diesel vehicles during chassis dynamometer testing conducted at the Environment Canada and California Air Resources Board vehicle emissions laboratories between 2001 and 2007. Per phase and composite FTP emission rates were measured. A subset of vehicles was also tested using other driving cycles to characterize emissions as a function of different driving conditions. Vehicles were both new (<6500 km) and in-use (6500–160,000 km) and were tested on low sulfur gasoline (<30 ppm) or low sulfur diesel (<300 ppm). Measurements from selected published studies were combined with these new measurements to give a test fleet of 467 vehicles meeting both US EPA and California criteria pollutant emissions standards between Tier 0 and Tier 2 Bin 3 or SULEV. Aggregate distance-based and fuel-based emission factors for N₂O are reported for each emission standard and for each of the different test cycles. Results show that the distinction between light duty automobile and light duty truck is not significant for any of the emission standards represented by the test fleet and the distinction between new and aged catalyst is significant for vehicles meeting all emission standards but Tier 2. This is likely due to the relatively low mileage accumulated by the Tier 2 vehicles in this study as compared to the durability requirement of the standard. The FTP composite N₂O emission factors for gasoline vehicles meeting emission standards more stringent than Tier 1 are substantially lower than those currently used by both Canada and the US for the 2005 inventories. N₂O emission factors from test cycles other than the FTP illustrate the variability of emission factors as a function of driving conditions. N₂O emission factors are shown to strongly correlate with NMHC/NMOG emission standards and less strongly with NO_X and CO emission standards. A review of several published reports on the effect of gasoline sulfur content on N₂O emissions suggests that additional research is needed to adequately quantify the increase in N₂O emissions as a function of fuel sulfur.     

PCDD/F emissions from heavy duty vehicle diesel engines

The currently available information on PCDD/F emissions from diesel vehicles is briefly surveyed. Considerable uncertainty is identified concerning the emissions from heavy duty diesel trucks which have been measured only twice so far. These measurements led to emission factors differing by a factor of 200; similar discrepancy was also revealed by measurements of ambient air in traffic tunnels. New PCDD/F emission measurement results are presented which have been carried out at the exhaust systems of a stationary engine and of a modern heavy duty vehicle engine at transient operation conditions simulated on a test bench. PCDD/F concentrations in the exhaust gases were found to be in the range of control blank samples. Based on the highest concentration observed in the truck engine exhaust (9.7 pg I-TEQ/dry standard m3) a worst case estimate of the annual PCDD/F emission freight from diesel fuel combustion in the European countries of about 30 g I-TEQ/year is calculated. This emission appears to be irrelevant compared to the overall emission rate of more than 6,000 g I-TEQ/year being inventoried recently. Finally the possibilities to link congener/homologue profiles of diesel emission to profiles found in food or human samples are discussed.     

A new approach to in-situ determination of roadside particle emission factors of individual vehicles under conventional driving conditions

A method for continuous on-road measurements of particle number emissions for both diesel- and petrol-fuelled vehicles is presented. The setup allows the determination of particle number emission factors on an individual vehicle basis by the simultaneous measurement of CO₂ and particle concentrations. As an alternative to previous measurements on the kerbside, the sample is taken directly in the street, with the advantage of sampling in-situ within the exhaust plumes of passing vehicles, allowing the separation of the individual high-concentration plumes. The method was tested in two experiments that were conducted in the Gothenburg area. In the first study, which was performed at an urban roadside, we were able to determine particle emission factors from individual vehicles in a common car fleet passing the measurement site. The obtained emission factors were of the same order of magnitude (between 1.4 × 10¹² and 1.8 × 10¹⁴ particles km^?1) as values published in the recent literature for light duty vehicles. An additional on-road experiment was conducted at a rural road with four light duty reference vehicles (three of them petrol-powered and one diesel-powered) at driving speeds of 50 and 70 km h^?1, realised with different engine speeds. The results of the traffic emission studies show that the method is applicable provided that instruments with an adequate dynamic range are used and that the traffic is not too dense. In addition, the variability in particle emissions for a specified driving condition was estimated.     

HCB,PCB, PCDD and PCDF emissions from ships

Since current estimates of hexachlorobenzene (HCB), polychlorinated biphenyls (PCB), dioxins (PCDD) and furans (PCDF) from ships are based on a relatively limited and old data set, an update of these emission factors has been outlined as a target towards improved Swedish emission inventories. Consequently, a comprehensive study was undertaken focusing on these emissions from three different ships during December 2003 to March 2004. Analyses were performed on 12 exhaust samples, three fuel oil samples and three lubricating oil samples from a representative selection of diesel engine models, fuel types and during different “real-world” operating conditions.The determined emissions corresponded reasonably well with previous measurements. The data suggest however that previous PCDD/PCDF emission factors are somewhat higher than those measured here. As expected the greatest emissions were observed during main engine start-up periods and for engines using heavier fuel oils. Total emissions for 2002, using revised emission factors, have been calculated based on Swedish sold marine fuels and also for geographical areas of national importance. In terms of their toxic equivalence (WHO-TEQ), the PCDD/PCDF emissions from ships using Swedish fuels are small (0.37–0.85 g TEQ) in comparison to recent estimates for the national total (ca. 45 g TEQ). Emissions from other land-based diesel engines (road vehicles, off-road machinery, military vehicles and locomotives) are estimated to contribute a further 0.18–0.42 g TEQ. Similarly, HCB and PCB emissions from these sources are small compared to 1995 national emission inventories.     

Estimations of real-world N2O emissions from road vehicles by means of measurements in a traffic tunnel

Ambient air measurements of N2O, NOx, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N2O for road traffic. Two different methods--relative and mass balance-were used to calculate a N2O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N2O/ km, with a range of 7-56 mg/km.     

Road traffic emission factors for heavy metals

Quantifying the emissions and concentrations of heavy metals in urban air is a prerequisite for assessing their health effects. In this paper a combination of measurements and modelling is used to assess the contribution from road traffic emissions. Concentrations of particulate heavy metals in air were measured simultaneously during 1 year at a densely trafficked street and at an urban background site in Stockholm, Sweden. Annual mean concentrations of cadmium were 50 times lower than the EU directive and for nickel and arsenic concentrations were 10 and six times lower, respectively. More than a factor of two higher concentrations was in general observed at the street in comparison to roof levels indicating the strong influence from local road traffic emissions. The only compound with a significantly decreasing trend in the urban background was Pb with 9.1 ng m^?3 in 1995/96 compared to 3.4 ng m^?3 2003/04. This is likely due to decreased emissions from wear of brake linings and reduced emissions due to oil and coal combustion in central Europe.Total road traffic emission factors for heavy metals were estimated using parallel measurements of NOx concentrations and knowledge of NOx emission factors. In general, the emission factors for the street were higher than reported in road tunnel measurements. This could partly be due to different driving conditions, since especially for metals which are mainly emitted from brake wear, more stop and go driving in the street compared to in road tunnels is likely to increase emissions. Total emissions were compared with exhaust emissions, obtained from the COPERT model and brake wear emissions based on an earlier study in Stockholm. For Cu, Ni and Zn the sum of brake wear and exhaust emissions agreed very well with estimated total emission factors in this study. More than 90% of the road traffic emissions of Cu were due to brake wear. For Ni more than 80% is estimated to be due to exhaust emissions and for Zn around 40% of road traffic emissions are estimated to be due to exhaust emissions. Pb is also mainly due to exhaust emissions (90%); a fuel Pb content of only 0.5 mg L^?1 would give similar emission factor as that based on the concentration increment at the street. This is the first study using simultaneous measurements of heavy metals at street and roof enabling calculations of emission factors using a tracer technique.     

Nonparametric factorial analysis of daily weigh-in-motion traffic: implications for the ozone “weekend effect” in Southern California

The Ozone Weekend Effect (OWE) has become increasingly more frequent and widespread in southern California since the mid-1970s. Although a number of hypotheses have been suggested to explain the effect, there remains uncertainty associated with the root factors contributing to elevated weekend ozone concentrations. Targeting the time window of the 1997 Southern California Ozone Study (SCOS97), this paper examines traffic activity data for 14 vehicle classes at 27 weigh-in-motion (WIM) stations in southern California. Nonparametric factorial analyses of light-duty vehicle (LDV) and heavy-duty truck (HDT) traffic volumes indicate significant differences in daily volumes by day of week and between the weekly patterns of daily LDV and HDT volumes. Across WIM stations, the daily LDV volume was highest on Friday and decreased by 10% on weekends compared to that on midweek days. In contrast, daily HDT volumes showed dramatic weekend drops of 53% on Saturday and 64% on Sunday. As a result, LDV to HDT ratios increased by 145% on weekends. Nonparametric tests also suggest that weekly traffic patterns varied significantly between WIM stations located close to (central) and far from (peripheral) the Los Angeles Metro area. Weekend increases in LDV/HDT ratios were more pronounced at central WIM sites due to greater weekend declines of HDT relative to LDV traffic. The implications of these weekly traffic patterns for the OWE in southern California were investigated by estimating daily WIM traffic on-road running exhaust emissions of total organic gas (TOG) and oxides of nitrogen (NO_x) using EMFAC2002 emission factors. The results support the California Air Resource Board's (CARB's) NO_x reduction hypothesis that greater weekend NO_x reductions relative to volatile organic compound (VOC) emissions, in combinations with the VOC-limited ozone system, contribute to the OWE observed in the region. The results from this study can be used to develop weekend on-road mobile emission inventories for the purpose of air quality modeling.     

Estimations of Real-World N2O Emissions from Road Vehicles by Means of Measurements in a Traffic Tunnel

Abstract

Ambient air measurements of N₂O, NO_x, CO, and HC based on grab sampling were conducted in a major traffic tunnel in Sweden, that carries up to 4,000 vehicles per hour, in order to estimate real-world emissions of N₂O for road traffic. Two different methods—relative and mass balance—were used to calculate a N₂O emission factor for the mixed vehicle fleet, which gave an average emission factor, at average speeds of 30-70 km/h, of approximately 25 mg N₂O/ km, with a range of 7-56 mg/km.     

Influence of pesticides contamination on the emission of PCDD/PCDF to the land from open burning of corn straws

Open burning of crop residues has been identified as an important emission source of PCDD/PCDF to the environment. This paper presents the first known data on the emission of PCDD/PCDF to the land considering the influence of pesticides applied in crops planting. Emission factor for PCDD/PCDF to the land from open burning of corn straw with pesticides contamination ranged from 0.07 to 0.57 ng WHO₂₀₀₅-TEQ/kg straw burned with a mean value of 0.24 ng WHO₂₀₀₅-TEQ/kg straw burned and median value of 0.20 ng WHO₂₀₀₅-TEQ/kg straw burned, respectively. The concentration was 35 to 270 times higher than that without additional pesticide contaminated. Initial observation was that emission factor for PCDD/PCDF from open burning of crop residues was overestimated in the former UNEP Dioxin Toolkit. Pesticides contamination should be considered in some hotpots where special and over dosed pesticides has been sprayed especially in developing countries.     

Evaluating the air quality impacts of the 2008 Beijing Olympic Games: On-road emission factors and black carbon profiles

The aggressive traffic interventions and emission control measures implemented to improve air quality during the 2008 Beijing Olympic Games created a valuable case study to evaluate the effectiveness of these measures on mitigating air pollution and protecting public health. In this paper, we report the results from our field campaign in summer 2008 on the on-road emission factors of carbon monoxide, black carbon (BC) and ultrafine particles (UFP) as well as the ambient BC concentrations. The fleet average emission factors for light-duty gasoline vehicles (LDGV) showed considerable reduction in the Olympic year (2008) compared to the pre-Olympic year (2007). Our measurement of Black Carbon (BC), a primary pollutant, at different elevations at the ambient site suggests consistent decrease in BC concentrations as the height increased near the ground level, which indicates that the nearby ground level sources, probably dominated by traffic, contributed to a large portion of BC concentrations in the lower atmospheric layer in Beijing during summertime. These observations indicate that people living in near ground levels experience higher exposures than those living in higher floors in Beijing. The BC diurnal patterns on days when traffic control were in place during the Olympic Games were compared to those on non-traffic-control days in both 2007 and in 2008. These patterns strongly suggest that diesel trucks are a major source of summertime BC in Beijing. The median BC concentration on Olympic days was 3.7 μg m⁻³, which was dramatically lower than the value on non-traffic-control days, indicating the effectiveness of traffic control regulations in BC reduction in Beijing.     

The impact of transportation control measures on emission reductions during the 2008 Olympic Games in Beijing,China

Traffic congestion and air pollution were two major challenges for the planners of the 2008 Olympic Games in Beijing. The Beijing municipal government implemented a package of temporary transportation control measures during the event. In this paper, we report the results of a recent research project that investigated the effects of these measures on urban motor vehicle emissions in Beijing. Bottom–up methodology has been used to develop grid-based emission inventories with micro-scale vehicle activities and speed-dependent emission factors. The urban traffic emissions of volatile organic compounds (VOC), carbon monoxide (CO), nitrogen oxides (NO_x) and particulate matter with an aerodynamic diameter of 10 μm or less (PM₁₀) during the 2008 Olympics were reduced by 55.5%, 56.8%, 45.7% and 51.6%, respectively, as compared to the grid-based emission inventory before the Olympics. Emission intensity was derived from curbside air quality monitoring at the North 4th Ring Road site, located about 7 km from the National Stadium. Comparison between the emission intensity before and during the 2008 Olympics shows a reduction of 44.5% and 49.0% in daily CO and NO_x emission from motor vehicles. The results suggest that reasonable traffic system improvement strategies along with vehicle technology improvements can contribute to controlling total motor vehicle emissions in Beijing after the Olympic Games.     

Emissions of unintentional persistent organic pollutants from open burning of municipal solid waste from developing countries

Open burning of waste is the most significant source of polychlorinated dibenzo-para-dioxins and dibenzofurans (PCDD/PCDF) in many national inventories prepared pursuant to the Stockholm Convention on Persistent Organic Pollutants. This is particularly true for developing countries. Emission factors for POPs such as PCDD/PCDF, dioxin-like polychlorinated biphenyls (dl-PCB) and penta- and hexachlorobenzenes (PeCBz/HCB) from open burning of municipal solid waste in China and Mexico are reported herein. Six different waste sources were studied varying from urban-industrial to semi-urban to rural. For PCDD/PCDF, the emission factors to air ranged from 3.0 to 650 ng TEQ kg⁻¹ waste and for dl-PCB from 0.092 to 54 ng TEQ kg⁻¹ waste. Emission factors for PeCBz (17-1200 ng kg⁻¹ waste) and HCB (24-1300 ng kg⁻¹ waste) spanned a wide but similar range. Within the datasets there is no indication of significant waste composition effect on emission factor with the exception of significantly higher Mexico rural samples.     

Emissions of Polychlorinated Dibenzo-p-Dioxins and Dibenzofurans from Various Industrial Sources

Abstract

This study characterized the emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) from the stack flue gases of 17 industrial sources, which were classified into 10 categories. The results show that the mean PCDD/PCDF concentration of secondary zinc smelter (Zn-S) and secondary copper smelter (Cu-S) is 2.44 ng international toxic equivalent (I-TEQ)/Nm³ (N represents normal conditions at 0 °C, 760 mmHg), which was found to be significantly greater than that of industrial waste incinerators (mean concentration = 0.15 ng I-TEQ/Nm³). These results imply that the controlling of secondary metallurgical melting processes is more important than industrial waste incineration for the reduction of PCDD/PCDF emissions. The mean emission factors of cement production, Zn-S and Cu-S, are 0.052, 1.99, and 1.73 μg I-TEQ/t product, respectively. For industrial waste incineration, the mean emission factors of waste rubber, waste liquor, waste sludge, industrial waste solid (IWI)-1, IWI-2, IWI-3, and IWI-4 are 0.752, 0.435, 0.760, 6.64, 1.67, 2.38, and 0.094 μg I-TEQ/t feed, respectively. Most of the PCDD/PCDF emission factors established in this study are less than those reported in previous studies, which could be because of the more stringent regulations for PCDD/PCDF emissions in recent years.     

Formation of artefacts while sampling emissions of PCDD/PCDF from open burning of biomass

Emission factors for PCDD/PCDF determined from open combustion are used to estimate national emission budgets; therefore, it is important to have confidence in their accuracy. It has been suspected that artefacts may form due to the presence of hot metal surfaces of sampling equipment, thus skewing emission factors. In this study, emissions of PCDD/PCDF from open burning of forest biomass over a brick hearth were sampled. Five experiments were carried out using a portable sampler. Experiments were designed where the key variable, sample hood and inlet temperatures were manipulated. Other variables such as fuel origin, type and density were consistent. The measured concentration of PCDD/PCDF in the smoke samples ranged from 0.01 μg TEQ (t fuel)⁻¹ at the lowest maximum hood temperature (185 °C) to 15 μg TEQ (t fuel)⁻¹ at the highest maximum hood temperature (598 °C). when hood inlet temperatures exceeded 400 °C emission factors were significantly elevated and this is attributed to the formation of artefacts that can cause the over estimation of emission factors. The increase in hood temperature also resulted in a change in the PCDD/PCDF congener and homologue profile of the emissions. For example at the lowest temperature (Fire 1) the PCDD/PCDF ratio measured was 50:1, whereas at the highest temperature (Fire 5) this ratio was about 0.53:1. When the sampler hood and inlet temperatures were kept in the normal operating range of <200 °C, emission factors were comparable to those observed in many previous studies in Australia with emissions dominated by PCDD.     

Concentrations of polychlorinated dibenzo-p-dioxins, dibenzofurans and non-ortho substituted biphenyls in polar bear milk from Svalbard (Norway)

Polychlorinated dibenzo-p-dioxins (PCDD), dibenzofurans (PCDF) and non-ortho substituted biphenyls (PCB, CB) were determined in 6 polar bear milk samples from Svalbard (Norway). For these compounds, no data for polar bears have been reported before from this region. Most of the PCDD/PCDF congeners were found at detectable levels. Concentrations expressed as 2,3,7,8-TCDD equivalents (Nordic model) were in the order of 1–3 pg/g⁻¹ fat (0.2–1.6 pg ml⁻¹ milk) which is comparable with ringed and harp seal blubber from the same region. On whole milk basis, concentrations were similar to those found in human milk. An estimation of the daily uptake via milk showed that the intake is lower for polar bears compared to humans. As in human milk, relatively high levels of OCDD were found in some polar bear milk samples. The PCDD/PCDF congener pattern in the milk was different to that found in polar bear fat from the Canadian Arctic. Non-ortho substituted PCB levels in polar bear milk were similar to those found in polar bear fat from the Canadian North. However, CB 77 or 169 dominated in the milk while CB 126 was the most abundant congener in fat. PCDD/PCDF levels expressed as 2,3,7,8-TE were highly correlated with the fat content of the milk. No correlation between CB and PCDD/PCDF concentrations was found. Some data indicate that PCDD/PCDF concentrations in polar bear milk decrease with increasing time after delivery.