Kinetic adsorption of application of carbon nanotubes for Pb（II） removal from aqueous solution

The capability of carbon nanotubes (CNTs) to adsorb lead (Pb) in aqueous solution was investigated. Batch mode adsorption experiment was conducted to determine the effects of pH, agitation speed, CNTs dosage and contact time. The removal of Pb(II) was reach to maximum value 85% or 83% at pH 5 or 40 mg/L of CNTs, respectively. Higher correlation coefficients from Langmuir isotherm model indicates the strong adsorptions of Pb(II) on the surface of CNTs (adsorption capacity Xm = 102.04 mg/g). From this study, the results indicates that the highest percentage removal of Pb (96.03%) can be achieved at pH 5, 40 mg/L of CNTs, contact time 80 min, and agitation speed 50 r/min.     

Rapid adsorption of toxic Pb(Ⅱ) ions from aqueous solution using multiwall carbon nanotubes synthesized by microwave chemical vapor deposition technique

Multiwall carbon nanotubes(MWCNTs) were synthesized using a tubular microwave chemical vapor deposition technique, using acetylene and hydrogen as the precursor gases and ferrocene as catalyst. The novel MWCNT samples were tested for their performance in terms of Pb(Ⅱ)binding. The synthesized MWCNT samples were characterized using Fourier Transform Infrared(FT-IR), Brunauer, Emmett and Teller(BET), Field Emission Scanning Electron Microscopy(FESEM) analysis, and the adsorption of Pb(Ⅱ) was studied as a function of p H,initial Pb(Ⅱ) concentration, MWCNT dosage, agitation speed, and adsorption time, and process parameters were optimized. The adsorption data followed both Freundlich and Langmuir isotherms. On the basis of the Langmuir model, Qmaxwas calculated to be 104.2 mg/g for the microwave-synthesized MWCNTs. In order to investigate the dynamic behavior of MWCNTs as an adsorbent, the kinetic data were modeled using pseudo first-order and pseudo second-order equations. Different thermodynamic parameters, viz., ΔH0, ΔS0and ΔG0were evaluated and it was found that the adsorption was feasible, spontaneous and endothermic in nature. The statistical analysis revealed that the optimum conditions for the highest removal(99.9%) of Pb(Ⅱ) are at p H 5, MWCNT dosage 0.1 g, agitation speed 160 r/min and time of 22.5 min with the initial concentration of 10 mg/L. Our results proved that microwave-synthesized MWCNTs can be used as an effective Pb(Ⅱ) adsorbent due to their high adsorption capacity as well as the short adsorption time needed to achieve equilibrium.     

Synthesis,characterization and application of Lagerstroemia speciosa embedded magnetic nanoparticle for Cr(Ⅵ)adsorption from aqueous solution

Lagerstroemia speciosa bark(LB) embedded magnetic nanoparticles were prepared by co-precipitation of Fe~(2+) and Fe~(3+) salt solution with ammonia and LB for Cr(Ⅵ) removal from aqueous solution.The native LB,magnetic nanoparticle(MNP),L.spedosa embedded magnetic nanoparticle(MNPLB) and Cr(Ⅵ) adsorbed MNPLB particles were characterized by SEM-EDX,TEM,BET-surface area,FT-IR,XRD and TGA methods.TEM analysis confirmed nearly spherical shape of MNP with an average diameter of 8.76 nm and the surface modification did not result in the phase change of MNP as established by XRD analysis,while led to the formation of secondary particles of MNPLB with diameter of 18.54 nm.Characterization results revealed covalent binding between the hydroxyl group of MNP and carboxyl group of LB particles and further confirmed its physico-chemical nature favorable for Cr(Ⅵ) adsorption.The Cr(Ⅵ) adsorption on to MNPLB particle as an adsorbent was tested under different contact time,initial Cr(Ⅵ) concentration,adsorbent dose,initial pH,temperature and agitation speed.The results of the equilibrium and kinetics of adsorption were well described by Langmuir isotherm and pseudo-second-order model,respectively.The thermodynamic parameters suggest spontaneous and endothermic nature of Cr(Ⅵ)adsorption onto MNPLB.The maximum adsorption capacity for MNPLB was calculated to be 434.78 mg/g and these particles even after Cr(Ⅵ) adsorption were collected effortlessly from the aqueous solution by a magnet.The desorption of Cr(Ⅵ)-adsorbed MNPLB was found to be more than 93.72%with spent MNPLB depicting eleven successive adsorption-desorption cycles.     

Response to comment on "Removal of heavy metals from aqueous solution by carbon nanotubes: adsorption equilibrium and kinetics"

We would like to thank Dr. Ho for his careful examination of our paper. We agree with the comment on our paper published in Journal of Environmental Sciences.     

Removal of cobalt(Ⅱ) ion from aqueous solution by chitosan-montmorillonite

Montmorillonite （MMT） modified with chitosan （CTS, molecular weight = S x 104） was applied to remove heavy metal cations by using Co2＋ as a model ion. An increase in MMT interlayer distance observed from X-ray diffraction indicates the intercalation of CTS into MMT. Together with the results of scanning electron microscopy and Fourier transform infrared spectroscopy, it was concluded that the composite material of CTS and MMT （CTS-- MMT） was prepared successfully. The mass ratio of CTS to MMT had a strong influence on the adsorption performance of CTS-MMT. The highest adsorption value of 150 mg/g was obtained over the composite material with CTS to MMT mass ratio of 0.25, which is much higher than those reported in other studies. The adsorption isotherms and kinetic results indicated that Co2＋ was adsorbed over CTS-MMT in a multilayer model, and the chemical sorption of Co2＋ was determined to be the rate-limiting step.     

Preparation, characterization and application of thiosemicarbazide grafted multiwalled carbon nanotubes for solid-phase extraction of Cd(Ⅱ), Cu(Ⅱ) and Pb(Ⅱ) in environmental samples

Thiosemicarbazide-grafted multi-walled carbon nanotubes were prepared and employed to investigate the pre-concentration of Cd（Ⅱ）, Cu（Ⅱ） and Pb（Ⅱ） from aqueous solution prior to their determination by ICP-OES. The resulting material was characterized by FT-IR, TGA and SEM. Various factors influencing the separation and pre-concentration were investigated. The enrichment factor typically is 60. Under optimized experimental conditions, the maximum adsorption capacities of Cd（Ⅱ）, Cu（Ⅱ） and Pb（Ⅱ） were found to be 1.98, 10.94, 3.69 mg/g, and the relative standard deviations are 〈 3.5% （n = 6）. The new adsorbent shows superior reusability and stability. The procedure was successfully applied to the determination of trace quantities of Cd（Ⅱ）, Cu（Ⅱ） and Pb（Ⅱ） in water samples.     

Synthesis of linear low-density polyethylene-g-poly (acrylic acid)-co-starch/organo-montmorillonite hydrogel composite as an adsorbent for removal of Pb(Ⅱ) from aqueous solutions

The purpose of this work is to remove Pb(II) from the aqueous solution using a type of hydrogel composite. A hydrogel composite consisting of waste linear low density polyethylene, acrylic acid, starch, and organo-montmorillonite was prepared through emulsion polymerization method. Fourier transform infrared spectroscopy (FTIR), Solid carbon nuclear magnetic resonance spectroscopy (CNMR)), silicon^-29 nuclear magnetic resonance spectroscopy (Si NMR)), and X-ray diffraction spectroscope ((XRD) were applied to characterize the hydrogel composite. The hydrogel composite was then employed as an adsorbent for the removal of Pb(II) from the aqueous solution. The Pb(II)-loaded hydrogel composite was characterized using Fourier transform infrared spectroscopy (FTIR)), scanning electron microscopy (SEM)), and X-ray photoelectron spectroscopy ((XPS)). From XPS results, it was found that the carboxyl and hydroxyl groups of the hydrogel composite participated in the removal of Pb(II). Kinetic studies indicated that the adsorption of Pb(II) followed the pseudo-second-order equation. It was also found that the Langmuir model described the adsorption isotherm better than the Freundlich isotherm. The maximum removal capacity of the hydrogel composite for Pb(II) ions was 430 mg/g. Thus, the waste linear low-density polyethylene-g-poly (acrylic acid)-co-starch/organo-montmorillonite hydrogel composite could be a promising Pb(II) adsorbent.     

Synthesis of linear low-density polyethylene-g-poly(acrylic acid)-co-starch/organo-montmorillonite hydrogel composite as an adsorbent for removal of Pb(Ⅱ) from aqueous solutions

The purpose of this work is to remove Pb(II) from the aqueous solution using a type of hydrogel composite. A hydrogel composite consisting of waste linear low density polyethylene, acrylic acid, starch, and organo-montmorillonite was prepared through emulsion polymerization method. Fourier transform infrared spectroscopy(FTIR), Solid carbon nuclear magnetic resonance spectroscopy(CNMR)), silicon-29 nuclear magnetic resonance spectroscopy(Si NMR)), and X-ray diffraction spectroscope((XRD) were applied to characterize the hydrogel composite. The hydrogel composite was then employed as an adsorbent for the removal of Pb(II) from the aqueous solution. The Pb(II)-loaded hydrogel composite was characterized using Fourier transform infrared spectroscopy(FTIR)),scanning electron microscopy(SEM)), and X-ray photoelectron spectroscopy((XPS)). From XPS results, it was found that the carboxyl and hydroxyl groups of the hydrogel composite participated in the removal of Pb(II). Kinetic studies indicated that the adsorption of Pb(II)followed the pseudo-second-order equation. It was also found that the Langmuir model described the adsorption isotherm better than the Freundlich isotherm. The maximum removal capacity of the hydrogel composite for Pb(II) ions was 430 mg/g. Thus, the waste linear low-density polyethylene-g-poly(acrylic acid)-co-starch/organo-montmorillonite hydrogel composite could be a promising Pb(II) adsorbent.     

Alkynyl carbon materials as novel and efficient sorbents for the adsorption of mercury(Ⅱ) from wastewater

For the first time, a series of alkynyl carbon materials(ACMs) were prepared via the mechanochemical reaction of CaC_2 with six polyhalogenated precursors, namely CCl_4,C_2Cl_6, C_2Cl_4, C_6Cl_6, C_6Br_6, and C_(14)H_4Br_(10)(ACM-1, ACM-2, ACM-3, ACM-4, ACM-5, and ACM-6,respectively) and used for the adsorptive removal of mercury from aqueous solutions.Based on preliminary investigations, the adsorption of mercury on ACM-5 was studied in depth. Specifically, the effect of p H on mercury adsorptivity, adsorption kinetics,thermodynamics, isotherms, and recyclability was studied. The adsorptivity of mercury on ACMs was found to be closely related to the hydrocarbon precursor, specific surface area of sorbent, and the alkynyl content. ACM-5 showed the best performance and is among the best raw carbonaceous sorbents reported so far, with a Langmuir saturated adsorption capacity of 191.9 mg g~(-1). The promising mercury adsorption performance mainly arises from the strong Lewis soft acid–soft base interactions between the alkynyl groups and mercury ions. The adsorption isotherms could be satisfactorily correlated with the Langmuir equation. The results show that the ACMs can be used as efficient sorbents for the removal of mercury and may also be useful for the adsorption of other heavy metals.     

Recovery of Cu(Ⅱ) from aqueous solution by induced crystallization in a long-term operation

The feasibility of copper recovery by induced crystallization in a long period(174 days) was investigated in a seeded fluidized bed reactor(FBR). The process was divided into 3 periods according to different influent conditions, and the period III was separated into III-a and IIIb due to the adjustment of the molar ratio of CO_3~(2-)concentration to copper concentration([CT]/[Cu~(2+)]). The removal efficiency could exceed 95% and the average effluent copper concentration decreased to 3.0 mg/L. The mean particle size of seed grains with copper crystals coating on, raised to 0.36 mm from initial 0.18 mm. During period III-a, the supersaturation exceeded 2.88 × 104, the removal efficiency decreased to 60%–80% and the particle size dropped to 0.30 mm, due to the generation of fines by homogeneous crystallization and seeds breaking. And the morphology of the crystals on the seed grains changed from rod-like to spherical which lead to the particle size decreasing. In period III-b,the supersaturation was modified by adjusting the molar ratio of [CT]/[Cu2+] to 1.2 from 2.The efficiency was back to 95% and the mean particle size grew to 0.36 mm at the end of IIIb, the crystals coating on the seeds turned back to rod-like products of good stability. This study illustrated that the copper salt crystal could keep on growing on the seed grains for over 150 days, the feasibility and controllability of copper recovery by induced crystallization process in FBR were satisfactory, even under the dramatic changes in influent conditions.     

Preparation and characterization of a novel hybrid chelating material for effective adsorption of Cu(Ⅱ) and Pb(Ⅱ)

The discharge of heavy metal ions such as Cu~2+and Pb~2+poses a severe threat to public health and the environment owing to their extreme toxicity and bioaccumulation through food chains Herein, we report a novel organic–inorganic hybrid adsorbent, Al(OH)_3-poly(acrylamide dimethyldiallylammonium chloride)-graft-dithiocarbamate(APD), for rapid and effectiv removal of Cu~2+and Pb~2+. In this adsorbent, the "star-like" structure of Al(OH)3 poly(acrylamide-dimethyldiallylammonium chloride) served as the support of dithiocarbamat(DTC) functional groups for easy access of heavy metal ions and assisted development of larg and compact floccules. The synthesized adsorbent was characterized by scanning electron microscopy(SEM), transmission electron microscopy(TEM), Fourier transform infrared spectroscopy(FTIR), and thermogravimetric analysis(TGA). APD was demonstrated to hav rapid adsorption kinetics with an initial rate of 267.379 and 2569.373 mg/(g·min) as well a superior adsorption capacities of 317.777 and 586.699 mg/g for Cu~2+and Pb~2+respectively. Th adsorption process was spontaneous and endothermic, involving intraparticle diffusion and chemical interaction between heavy metal ions and the functional groups of APD. To assess it versatility and wide applicability, APD was also used in turbid heavy metal wastewater, and performed well in removing suspended particles and heavy metal ions simultaneously through flocculation and chelation. The rapid, convenient and effective adsorption of Cu~2+and Pb~2+give APD great potential for heavy metal decontamination in industrial applications.     

Preparation of Fe–Co based MOF-74 and its effective adsorption of arsenic from aqueous solution

To obtain a cost-effective adsorbent for the removal of arsenic in water,a novel nanostructured Fe–Co based metal organic framework(MOF-74)adsorbent was successfully prepared via a simple solvothermal method.The adsorption experiments showed that the optimal molar ratio of Fe/Co in the adsorbent was 2:1.The Fe_2Co_1MOF-74 was characterized by various techniques and the results showed that the nanoparticle diameter ranged from60 to 80 nm and the specific surface area was 147.82 m~2/g.The isotherm and kinetic parameters of arsenic removal on Fe_2Co_1MOF-74 were well-fitted by the Langmuir and pseudo-second-order models.The maximum adsorption capacities toward As(III)and As(V)were 266.52 and 292.29 mg/g,respectively.The presence of sulfate,carbonate and humic acid had no obvious effect on arsenic adsorption.However,coexisting phosphate significantly hindered the removal of arsenic,especially at high concentrations(10 mmol/L).Electrostatic interaction and hydroxyl and metal–oxygen groups played important roles in the adsorption of arsenic.Furthermore,the prepared adsorbent had stable adsorption ability after regeneration and when used in a real-water matrix.The excellent adsorption performance of Fe_2Co_1MOF-74 material makes it a potentially promising adsorbent for the removal of arsenic.     

Novel functional fiber loaded with carbon dots for the deep removal of Cr(Ⅵ) by adsorption and photocatalytic reduction

A novel functional fiber(PAN-CDs) loaded with carbon dots(CDs) with excellent photoreduction and adsorption properties for Cr(VI) was prepared via an amidization reaction between the CDs' carboxyl groups and amine groups on polyacrylonitrile(PAN)-based ion exchange fibers, which could completely preserve the fluorescence properties of the CDs. The photoluminescence(PL), photocatalysis and adsorption properties of PAN-CDs were characterized and analyzed. The PAN-CDs possess high adsorption capacity(297.6 mg/g) and excellent kinetic behavior(attaining adsorption equilibrium in 30 min)for Cr(VI) adsorption. Furthermore, the residual Cr(VI)(approximately 3 mg/L) after adsorption could be removed completely by subsequent photoreduction by the PAN-CDs.The Cr-saturated PAN-CDs could be easily separated by filtering and regenerated, with no observable decay of removal efficiency after five regeneration cycles. In addition, due to the PL quenching action of Cr(VI), the PAN-CDs can also be used as sensor for quantitative detection of trace Cr(VI) in aqueous solution.     

Removal of perchlorate from aqueous solution by cross-linked Fe(Ⅲ)-chitosan complex

Cross-linked Fe（III）-chitosan composite （Fe-CB） was used as the adsorbent for removing perchlorate from the aqueous solution. The adsorption experiments were carried out by varying contact time, initial concentrations, temperatures, pH, and the presence of co-existing anions. The morphology of the adsorbent was discussed using FT-IR and SEM with X-EDS analysis. The pH ranging from 3.0-10.2 exhibited very little effect on the adsorption capability. The perchlorate uptake onto Fe-CB obeyed Langmuir isotherm model. The adsorption process was rapid and the kinetics data obeyed the pseudo second-order model well. The eluent of 2.5% （W/V） NaC1 could regenerate the exhausted adsorbent efficiently. The adsorption mechanism was also discussed.     

Adsorption of Co(Ⅱ) from aqueous solutions by water treatment residuals

A study on the removal of Co(Ⅱ) from aqueous solutions by water treatment residuals(WTR)was conducted in batch conditions. The sorption process of Co(Ⅱ) followed pseudosecondorder kinetics, with 30 hr required to reach equilibrium. Using the Langmuir adsorption isotherm model, a relatively high maximum sorption capacity of 17.31 mg/g Co(Ⅱ) was determined. The adsorption of Co(Ⅱ) was dependent on pH values and was affected by the ionic strength. Results show that Co(Ⅱ) adsorption was a spontaneous endothermic process and was favorable at high temperature. Most of the adsorbed Co(Ⅱ) stayed on the WTR permanently, whereas only small amounts of adsorbed Co(Ⅱ) were desorbed. The shifting of peaks in FT-IR spectra indicated that Co(Ⅱ) interacted with the WTR surface through strong covalent bond formation with Fe(Al)–O functional groups. It was concluded that WTR can be a suitable material from which to develop an efficient adsorbent for the removal of Co(Ⅱ) from wastewater.     

Enhanced adsorption of Methylene Blue from aqueous solution by chitosan-g-poly （acrylic acid）/vermiculite hydrogel composites

A series of chitosan-g-poly (acrylic acid)/vermiculite hydrogel composites were synthesized and used as adsorbents for the investigation of the e ect of process parameters such as vermiculite content, pH of dye solution, contact time, initial concentration of dye solution, temperature, ionic strength and concentration of surfactant sodium dodecyl sulfate on the removal of Methylene Blue (MB) from aqueous solution. The results showed that the adsorption capacity for dye increased with increasing pH, contact time and initial dye concentration, but decreased with increasing temperature, ionic strength and sodium dodecyl sulfate concentration in the present of the surfactant. The adsorption kinetics of MB onto the hydrogel composite followed pseudo second-order kinetics and the adsorption equilibrium data obeyed Langmuir isotherm. By introducing 10 wt.% vermiculite into chitosan-g-poly (acrylic acid) polymeric network, the obtaining hydrogel composite showed the highest adsorption capacity for MB, and then could be regarded as a potential adsorbent for cationic dye removal in a wastewater treatment process.     

Biosorption of cadmium(Ⅱ) and lead(Ⅱ) ions from aqueous solutions onto dried activated sludge

The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions（Cd（Ⅱ） and Pb（Ⅱ）） followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd（Ⅱ） and Pb（Ⅱ） biosorption onto dried activated sludge was their binding with amide I group.     

Biosorption of cadmium(Ⅱ) and lead(Ⅱ) ions from aqueous solutions onto dried activated sludge

The removal of heavy-metal ions from aqueous solutions by using dried activated sludge has been investigated in batch systems. Effect of solution pH, initial metal ion concentration, and temperature were determined. The results of the kinetic studies showed that the uptake processes of the two metal ions(Cd(Ⅱ) and Pb(Ⅱ)) followed the pseudo-second-order rate expression. The equilibrium data fitted very well to both the Langmuir and Freundlich adsorption models. The FT-IR analysis showed that the main mechanism of Cd(Ⅱ) and Pb(Ⅱ) biosorption onto dried activated sludge was their binding with amide I group.     

Evaluation of adsorption capacities of humic acids extracted from Algerian soil on polyaniline for application to remove pollutants such as Cd(Ⅱ), Zn(Ⅱ) and Ni(Ⅱ) and characterization with cavity microelectrode

The adsorption capacities of new humic acids isolated from Yakouren forest (YHA) and Sahara (Tamenrasset: THA) soils (Algeria) and commercial humic acid (PFHA) on polyaniline emeraldine base (PEB) were studied at pH 6.6. Also the adsorption of heavy metals such as Cd2+, Zn2+ and Ni2+ on humic acid-polyaniline systems (HA-PEB) was investigated at the same conditions. HA-PEB compounds were characterized by scanning electron microscopy (SEM), infrared spectrometry and cavity microelectrode. In addition, batch adsorption and cavity microelectrode were used in the adsorption study of Cd2+, Zn2+ and Ni2+ on HA-PEB. To develop biocaptors of polluting metals using a cavity microelectrode modified by HA-PEB systems, the adsorption kinetic and adsorption capacity were investigated. The SEM analysis showed that the presence of humic acid affected the PEB surface and caused the formation of a granular morphology. The maximum adsorption capacities (qmax) of PFHA, THA and YHA determined by adsorption isotherms were 91.31, 132.1 and 151.0 mg/g, respectively. Batch adsorption results showed that qmax of Cd2+, Zn2+ and Ni2+ on HA-PEB followed the order: THA-PEB > YHA-PEB > PFHA-PEB. The voltammograms obtained with HA-PEB modified cavity microelectrode showed the appearance of new redox couples reflecting the adsorption of HA on PEB. Metal-humic acid-polyaniline voltammograms were characterized by appearance of oxidation-reduction couples or reduction wave corresponding to metal. Finally, the result may be exploited to develop a biocaptor based on the cavity microelectrode amended by THA-PEB and YHA-PEB.