Changes in different organic matter fractions during conventional treatment and advanced treatment

XAD-8 resin isolation of organic matter in water was used to divide organic matter into the hydrophobic and hydrophilic fractions. A pilot plant was used to investigate the change in both fractions during conventional and advanced treatment processes. The treatment of hydrophobic organics (HPO), rather than hydrophilic organicas (HPI), should carry greater emphasis due to HPO’s higher trihalomethane formation potential (THMFP) and haloacetic acid formation potential (HAAFP). The removal of hydrophobic matter and its transmission into hydrophilic matter reduced ultimate DBP yield during the disinfection process. The results showed that sand filtration, ozonation, and biological activated carbon (BAC) filtration had distinct influences on the removal of both organic fractions. Additionally, the combination of processes changed the organic fraction proportions present during treatment. The use of ozonation and BAC maximized organic matter removal e ciency, especially for the hydrophobic fraction. In sum, the combination of pre-ozonation, conventional treatment, and O3-BAC removed 48% of dissolved organic carbon (DOC), 60% of HPO, 30% of HPI, 63% of THMFP, and 85% of HAAFP. The use of conventional treatment and O3-BAC without pre-ozonation had a comparable performance, removing 51% of DOC, 56% of HPO, 45% of HPI, 61% of THMFP, and 72% of HAAFP. The e ectiveness of this analysis method indicated that resin isolation and fractionation should be standardized as an applicable test to help assess water treatment process e ciency.     

Removal and transformation of organic matters in domestic wastewater during lab-scale chemically enhanced primary treatment and a trickling filter treatment

To find a simple and economical way for treating the domestic wastewater in small counties and towns, a process combining chemically enhanced primary treatment and a trickling filter (CEPT-TF, representing the physical and biological effects) was constructed and operated in laboratory conditions. The characteristic behaviors of dissolved organic matter in raw wastewater and effluents were examined during steady-state operation. Experimental results showed that the process of CEPT and TF in series was beneficial for the removal of hydrophobic and hydrophilic organics. Specially, the hydrophobic and aromatic materials could be preferentially removed in the CEPT unit, and the hydrophilic fraction in the TF. Structural changes of the organic fractions during the operation of the different units were also characterized via spectrum analysis.     

Disinfection byproduct precursor removal by enhanced coagulation and their distribution in chemical fractions

Raw water from the Songhua River was treated by four types of coagulants, ferric chloride(FeCl3), aluminum sulfate(Al2(SO4)3),polyaluminum chloride(PACl) and composite polyaluminum(HPAC), in order to remove dissolved organic matter(DOM). Considering the disinfection byproduct(DBP) precursor treatability, DOM was divided into five chemical fractions based on resin adsorption.Trihalomethane formation potential(THMFP) and haloacetic acid formation potential(HAAFP) were measured for each fraction. The results showed that hydrophobic acids(HoA), hydrophilic matter(HiM) and hydrophobic neutral(HoN) were the dominant fractions.Although both HoN and HoA were the main THM precursors, the contribution for THMFP changed after coagulation. Additionally,HoA and HiM were the main HAA precursors, while the contribution of HoN to HAAFP significantly increased after coagulation.HoM was more easily removed than HiM, no matter which coagulant was used, especially under enhanced coagulation conditions.DOC removal was highest for enhanced coagulation using FeCl3 while DBPFP was lowest using PACl. This could indicate that not all DOC fractions contained the precursors of DBPs. Reduction of THMFP and HAAFP by PACl under enhanced coagulation could reach51% and 59% respectively.     

Removal natural organic matter in typical south-China source water during enhanced coagulation of a with IPF-PACl

Systematic investigation on enhancing removal of natural organic matter （NOM） using inorganic polymer flocculant （IPF）, polyaluminum chloride（PACI） and polyacrylamide（PAM） was performed in a typical south-China source water. Enhanced coagulation and applying polymer flocculant-aid were compared through jar tests and pilot tests. Raw water and settled water were characterized and fractionated by resin adsorption. The results show that DOC composes major part of TOC. The DOC distribution keeps relatively stable all around the year with typical high amounts of the hydrophilic matter around 50%. The distribution between HoB, HoA and HoN varies and undergoes fluctuation with the year round. During the summer season, the HoN becomes gradually the major part in hydrophobic parts. PACI with the species being tailor-made shows little pH effect during coagulation. The enhanced coagulation dosage for PACI could be 4.5 mg/L for the typical source water. The highest TOC removal achieved 31%. To be economically, 3 mg/L dose is the optimum dosage. Although hydrophilic fractions of NOM of both treatment strategies are removed about 30%, NOM causing UV254 absorbance were well removed（about 90%）. Hydrophobic bases and acids fractions are much more removed under enhanced conditions. The hydrophilic fraction could be better removed using PAM, the polymer coagulant aid.     

Transformations of particles, metal elements and natural organic matter in different water treatment processes

Characterizing natural organic matter （NOM）, particles and elements in different water treatment processes can give a useful information to optimize water treatment operations. In this article, transformations of particles, metal elements and NOM in a pilot-scale water treatment plant were investigated by laser light granularity system, particle counter, glass-fiber membrane filtration, inductively coupled plasma-optical emission spectroscopy, ultra filtration and resin absorbents fractionation. The results showed that particles, NOM and trihalomethane formation precursors were removed synergistically by sequential treatment of different processes. Preozonation markedly changed the polarity and molecular weight of NOM, and it could be conducive to the following coagulation process through destabilizing particles and colloids; mid-ozonation enhanced the subsequent granular activated carbon （GAC） filtration process by decreasing molecular weight of organic matters. Coagulation-flotation and GAC were more efficient in removing fixed suspended solids and larger particles; while sand-filtration was more efficient in removing volatile suspended solids and smaller particles. Flotation performed better than sedimentation in terms of particle and NOM removal. The type of coagulant could greatly affect the performance of coagulation-flotation. Pre-hydrolyzed composite coagulant （HPAC） was superior to FeCl3 concerning the removals of hydrophobic dissolved organic carbon and volatile suspended solids. The leakages of flocs from sand-filtration and microorganisms from GAC should be mitigated to ensure the reliability of the whole treatment system.     

Simultaneous removal of dissolved organic matter and bromide from drinking water source by anion exchange resins for controlling disinfection by-products

Anion exchange resins （AERs） with different properties were evaluated for their ability to remove dissolved organic matter （DOM） and bromide, and to reduce disinfection by-product （DBP） formation potentials of water collected from a eutrophic surface water source in Japan. DOM and bromide were simultaneously removed by all selected AERs in batch adsorption experiments. A polyacrylic magnetic ion exchange resin （MIEX） showed faster dissolved organic carbon （DOC） removal than other AERs because it had the smallest resin bead size. Aromatic DOM fractions with molecular weight larger than 1600 Da and fluorescent organic fractions of fulvic acid- and humic acid-like compounds were efficiently removed by all AERs. Polystyrene AERs were more effective in bromide removal than polyacrylic AERs. This result implied that the properties of AERs, i.e. material and resin size, influenced not only DOM removal but also bromide removal efficiency, MIEX showed significant chlorinated DBP removal because it had the highest DOC removal within 30 rain, whereas polystyrene AERs efficiently removed brominated DBPs, especially brominated trihalomethane species. The results suggested that, depending on source water DOM and bromide concentration, selecting a suitable AER is a key factor in effective control of chlorinated and brominated DBPs in drinking water.     

Effect of ozone on the performance of a hybrid ceramic membrane-biological activated carbon process

Two hybrid processes including ozonation-ceramic membrane-biological activated carbon （BAC） （Process A） and ceramic membrane-BAC （Process B） were compared to treat polluted raw water. The performance of hybrid processes was evaluated with the removal efficiencies of turbidity, ammonia and organic matter. The results indicated that more than 99% of particle count was removed by both hybrid processes and ozonation had no significant effect on its removal. BAC filtration greatly improved the removal of ammonia. Increasing the dissolved oxygen to 30.0 mg/L could lead to a removal of ammonia with concentrations as high as 7.80 mg/L and 8.69 mg/L for Processes A and B, respectively. The average removal efficiencies of total organic carbon and ultraviolet absorbance at 254 nm （UV254, a parameter indicating organic matter with aromatic structure） were 49% and 52% for Process A, 51% and 48% for Process B, respectively. Some organic matter was oxidized by ozone and this resulted in reduced membrane fouling and increased membrane flux by 25%-30%. However, pre-ozonation altered the components of the raw water and affected the microorganisms in the BAC, which may impact the removals of organic matter and nitrite negatively.     

Effects of Ca(OH)2 assisted aluminum sulfate coagulation on the removal of humic acid and the formation potentials of tri-halomethanes and haloacetic acids in chlorination

The effects of addition of calcium hydroxide on aluminum sulphate(or alum) coagulation for removal of natural organic matter(NOM) and its subsequent effect on the formation potentials of two major types of regulated disinfection byproducts(DBPs),haloacetic acids(HAAs) and trihalomethanes(THMs),have been examined.The results revealed several noteworthy phenomena.At the optimal coagulation pH(i.e.6),the coagulation behavior of NOM water solutions versus alum dose,showed large variation and a consequent great change in the formation potentials of the DBPs at certain coagulant doses.However,with addition of a relatively small amount of Ca(OH) 2,although the zeta potential of coagulated flocs remained almost the same,NOM removal became more consistent with alum dose.Importantly,also the detrimental effect of charge reversal on NOM removal at the low coagulant dose disappeared.This resulted in a steady decrease in the formation potentials of DBPs as a function of the coagulant dose.Moreover,the addition of Ca(OH) 2 broadened the pH range of alum coagulation and promoted further reduction of the formation potentials of the DBPs.The enhancement effects of Ca(OH) 2 assisted alum coagulation are especially pronounced at pH 7 and 8.Finally,synchronous fluorescence spectra showed that the reduction in DBPs formation potential by Ca(OH) 2-assisted alum coagulation was connected to an enhanced removal of small hydrophobic and hydrophilic HA molecules.Ca(OH) 2-assistance of alum coagulation appeared to increase substantially the removal of the hydrophilic HA fraction responsible for HAAs formation,prompting further reduction of HAA formation potentials.     

Performance of two biofilters with neutral and low pH treating off-gases

Two different functional biofilters were carried out and compared for the treatment of off-gas containing multicomponent odors and volatile organic compounds (VOCs) in this study. The effects of pH values and the empty bed retention time (EBRT) on the performance of the bioreactors were studied; and the characteristics of microbial populations in the two biofilters were also determined. The experimental results indicated that the removal effciencies of hydrophilic compounds such as butyric acid and ammonia ...     

Investigating the coagulation of non-proteinaceous algal organic matter: Optimizing coagulation performance and identification of removal mechanisms

The removal of algal organic matter(AOM) is a growing concern for the water treatment industry worldwide. The current study investigates coagulation of non-proteinaceous AOM(AOM after protein separation), which has been minimally explored compared with proteinaceous fractions. Jar tests with either aluminum sulphate(alum) or polyaluminium chloride(PACl) were performed at doses of 0.2–3.0 mg Al per 1 mg of dissolved organic carbon in the p H range 3.0–10.5. Additionally, non-proteinaceous matter was characterized in terms of charge, molecular weight and carbohydrate content to assess the treatability of its different fractions. Results showed that only up to 25% of non-proteinaceous AOM can be removed by coagulation under optimized conditions. The optimal coagulation p H(6.6–8.0 for alum and 7.5–9.0 for PACl) and low surface charge of the removed fraction indicated that the prevailing coagulation mechanism was adsorption of non-proteinaceous matter onto aluminum hydroxide precipitates. The lowest residual Al concentrations were achieved in very narrow p H ranges, especially in the case of PACl. High-molecular weight saccharidelike organics were amenable to coagulation compared to low-molecular weight( 3 k Da)substances. Their high content in non-proteinaceous matter(about 67%) was the reason for its low removal. Comparison with our previous studies implies that proteinaceous and nonproteinaceous matter is coagulated under different conditions due to the employment of diverse coagulation mechanisms. The study suggests that further research should focus on the removal of low-molecular weight AOM, reluctant to coagulate, with other treatment processes to minimize its detrimental effect on water safety.     

Toxic effects of acetochlor, methamidophos and their combination on nifH gene in soil

Toxic effects of two agrochemicals on nifH gene in agricultural black soil were investigated using denaturing gradient gel electrophoresis （DGGE） and sequencing approaches in a microcosm experiment. Changes of soil nifH gene diversity and composition were examined following the application of acetochlor, methamidophos and their combination. Acetochlor reduced the nifH gene diversity （both in gene richness and diversity index values） and caused changes in the nifH gene composition. The effects of acetochlor on nifH gene were strengthened as the concentration of acetochlor increased. Cluster analysis of DGGE banding patterns showed that nifH gene composition which had been affected by low concentration of acetochlor （50 mg/kg） recovered firstly. Methamidophos reduced nifH gene richness that except at 4 weeks. The medium concentration of methamidophos （150 mg/kg） caused the most apparent changes in nifH gene diversity at the first week while the high concentration of methamidophos （250 mg/kg） produced prominent effects on nifH gene diversity in the following weeks. Cluster analysis showed that minimal changes of nifH gene composition were found at 1 week and maximal changes at 4 weeks. Toxic effects of acetochlor and methamidophos combination on nifH gene were also apparent. Different nifH genes （bands） responded differently to the impact of agrochemicals： four individual bands were eliminated by the application of the agrochemicals, five bands became predominant by the stimulation of the agrochemicals, and four bands showed strong resistance to the influence of the agrochemicals. Fifteen prominent bands were partially sequenced, yielding 15 different nifH sequences, which were used for phylogenetic reconstructions. All sequences were affiliated with the alpha- and beta-proteobacteria, showing higher similarity to eight different diazotrophic genera.     

Arsenic uptake by arbuscular mycorrhizal maize （Zea mays L.） grown in an arsenic-contaminated soil with added phosphorus

The effects of arbuscular mycorrhizal (AM) fungus (Glomus mosseae) and phosphorus (P) addition (100 mg/kg soil) on arsenic (As) uptake by maize plants (Zea mays L.) from an As-contaminated soil were examined in a glasshouse experiment.Non-mycorrhizal and zero-P addition controls were included.Plant biomass and concentrations and uptake of As,P,and other nutrients,AM colonization,root lengths,and hyphal length densities were determined.The results indicated that addition of P significantly inhibited root colonization and development of extraradical mycelium.Root length and dry weight both increased markedly with mycorrhizal colonization under the zero-P treatments,but shoot and root biomass of AM plants was depressed by P application.AM fungal inoculation decreased shoot As concentrations when no P was added,and shoot and root As concentrations of AM plants increased 2.6 and 1.4 times with P addition,respectively.Shoot and root uptake of P,Mn,Cu,and Zn increased,but shoot Fe uptake decreased by 44.6%,with inoculation, when P was added.P addition reduced shoot P,Fe,Mn,Cu,and Zn uptake of AM plants,but increased root Fe and Mn uptake of the nonmycorrhizal ones.AM colonization therefore appeared to enhance plant tolerance to As in low P soil,and have some potential for the phytostabilization of As-contaminated soil,however,P application may introduce additional environmental risk by increasing soil As mobility.     

Potential of plant polyphenol oxidases in the decolorization and removal of textile and non-textile dyes

In this study an effort has been made to use plant polyphenol oxidases; potato （Solanum tuberosum） and brinjal （Solanum melongena）, for the treatment of various important dyes used in textile and other industries. The ammonium sulphate fractionated enzyme preparations were used to treat a number of dyes under various experimental conditions. Majority of the treated dyes were maximally decolorized at pH 3.0. Some of the dyes were quickly decolorized whereas others were marginally decolorized. The initial first hour was sufficient for the maximum decolorization of dyes. The rate of decolorization was quite slow on long treatment of dyes. Enhancement in the dye decolorization was noticed on increasing the concentration of enzymes. The complex mixtures of dyes were treated with both preparations of polyphenol oxidases in the buffers of varying pH values. Potato polyphenol oxidase was significantly more effective in decolorizing the dyes to higher extent as compared to the enzyme obtained from brinjal polyphenol oxidase. Decolorization of dyes and their mixtures, followed by the formation of an insoluble precipitate, which could be easily removed simply by centrifugation.     

Removal of heavy metals from sewage sludge by low costing chemical method and recycling in agriculture

ＲｅｍｏｖａｌｏｆｈｅａｖｙｍｅｔａｌｓｆｒｏｍｓｅｗａｇｅｓｌｕｄｇｅｂｙｌｏｗｃｏｓｔｉｎｇｃｈｅｍｉｃａｌｍｅｔｈｏｄａｎｄｒｅｃｙｃｌｉｎｇｉｎａｇｒｉｃｕｌｔｕｒｅＷｕＱｉｔａｎｇ，ＮｙｉｒａｎｄｅｇｅＰａｓｃａｓｉｅ，ＭｏＣｅｈｕｉＦ...     

Single and joint effects of pesticides and mercury on soil urease

The influence of two pesticides including chlorimuron-ethyl and furadan and mercury （Hg） on urease activity in 4 soils （meadow burozem and phaeozem） was investigated. The soils were exposed to various concentrations of the two pesticides and Hg individually and simultaneously. Results showed that there was a close relationship between urease activity and organic matter content in soil. Chlorimuron-ethyl and furadan could both activate urease in the 4 soils. The maximum increment of urease activity by chlorimuronethyl was up to 14%-18%. There was almost an equal increase （up to 13%-21%） in the urease activity by furadan. On the contrary, Hg markedly inhibited soil urease activity. A logarithmic equation was used to describe the relationship （P〈0.05） between the concentration of Hg and the activity of soil urease in the 4 tested soils. Semi-effect dose （ED50） values by the stress of Hg based on the inhibition of soil urease in the 4 soils were 88, 5.5, 24 and 20 mg/kg, respectively, according to the calculation of the corresponding equations. The interactive effect of chlorimuron-ethyl or furadan with metal Hg on soil urease was mainly synergic at the highest tested concentrations.     

Isolation and preliminary characterization of a 3-chlorobenzoate degrading bacteria

A study was conducted to compare the diversity of 2-, 3-, and 4-chlorobenzoate degraders in two pristine soils and one contaminated sewage sludge. These samples contained strikingly different populations of mono-chlorobenzoate degraders. Although fewer cultures were isolated in the uncontaminated soils than contaminated one, the ability of microbial populations to mineralize chlorobenzoate was widespread. The 3- and 4-chlorobenzoate degraders were more diverse than the 2-chlorobenzoate degraders. One of the strains isolated from the sewage sludge was obtained. Based on its phenotype, chemotaxonomic properties and 16S rRNA gene, the organism S-7 was classified as Rhodococcus erythropolis. The strain can grow at temperature from 4 to 37℃. It can utilize several （halo）aromatic compounds. Moreover, strain S-7 can grow and use 3-chlorobenzoate as sole carbon source in a temperatures range of 10-30℃ with stoichiometric release of chloride ions. The psychrotolerant ability was significant for bioremediation in low temperature regions. Catechol and chlorocatechol 1,2-dioxygenase activities were present in cell free extracts of the strain, but no （chloro）catechol 2,3- dioxygenase activities was detected. Spectral conversion assays with extracts from R. erythropolis S-7 showed accumulation of a compound with a similar UV spectrum as chloro-cis,cis-muconate from 3-chlorobenzoate. On the basis of these results, we proposed that S-7 degraded 3-chlorobenzoate through the modified ortho-cleave pathway.     

Organochlorine pesticides in soils under different land usage in the Taihu Lake region, China

A field study was conducted in the Taihu Lake region, China in 2004 to reveal the organochlorine pesticide concentrations in soils after the ban of these substances in the year 1983. Thirteen organochlorine pesticides (OCPs) were analyzed in soils from paddy field, tree land and fallow land. Total organochlorine pesticide residues were higher in agricultural soils than in uncultivated fallow land soils. Among all the pesticides, ΣDDX (DDD, DDE and DDT) had the highest concentration for all the soil samples, ranging from 3.10 ng/g to 166.55 ng/g with a mean value of 57.04 ng/g and followed by ΣHCH, ranging from 0.73 ng/g to 60.97 ng/g with a mean value of 24.06 ng/g. Dieldrin, endrin, HCB and α-endosulfan were also found in soils with less than 15 ng/g. Ratios of p,p'-(DDD DDE)/DDT in soils under three land usages were: paddy field ＞ tree land ＞ fallow land, indicating that land usage inlfuenced the degradation of DDT in soils. Ratios of p,p'-(DDD DDE)/DDT ＞1, showing aged residues of DDTs in soils of the Taihu Lake region. The results were discussed with data from a former study that showed very low actual concentrations of HCH and DDT in soils in the Taihu Lake region, but according to the chemical half-lives and their concentrations in soils in 1980s, the concentration of DDT in soils seemed to be underestimated. In any case our data show that the ban on the use of HCH and DDT resulted in a tremendous reduction of these pesticide residues in soils, but there are still high amounts of pesticide residues in soils, which need more remediation processes.     

Sorption of 1-naphthol by plant cuticular fractions

The contribution of aliphatic-rich plant biopolymer to sorption of hydrophobic organic compounds is significantly important because of their preservation and accumulation in the soil environment,but sorption mechanism is still not fully understood.In this study, sorption of 1-naphthol by plant cuticular fractions was examined to better understand the contributions of respective fraction.Toward this end,cuticular materials were isolated from the fruits of tomato by chemical method.The tomato cuticle sheet consisted of waxes (6.5 wt%),cuticular monomer (69.5 wt%),and polysaccharide (24.0 wt%).Isotherms of l-naphthol to the cuticular fractions were nonlinear (N value (0.82-0.90)) at the whole tested concentration ranges.The KodKow ratios for bulk cuticle (TC1),dewaxed cuticle (TC2),cutin (TC4),and desugared cuticle (TC5) were larger than unity,suggested that tomato bulk cuticle and cutin are much powerful solption medium.Sorption capability of cutin (TC4) was 2.4 times higher than the nonsaponifiable fraction (TC3).The 1-naphthol interactions with tomato cuticular materials were governed by both hydrophobic-type interactions and polar (H-bonding) interactions. Removal of the wax and polysaccharide materials from the bulk tomato cuticle caused a significant increase in the sorption ability of the cuticular material.There was a linear negative trend between K_(oc) values and the amount of polysaccharides or fraction's polarities ((N O)/C);while a linear positive relationship between K_(oc) values and the content of cutin monomer (linear R~2=0.993) was observed for present in the cuticular fractions.Predominant sorbent of the hydrophobic organic compounds (HOCs) in the plant cuticular fraction was the cutin monomer,contributing to 91.7% of the total sorption of tomato bulk cuticle.     

Alterations of organ histopathology and metallolhionein mRNA expression in silver barb, Puntius gonionotus during subchronic cadmium exposure

Common silver barb,Puntius gonionotus,exposed to the nominal concentration of 0.06 mg/L Cd for 60 d,were assessed for histopathological alterations(gills,liver and kidney),metal accumulation,and metallothionein(MT)mRNA expression.Fish exhibited pathological symptoms such as hypertrophy and hyperplasia of primary and secondary gill lamellae,vacuolization in hepatocytes,and prominent tubular and glomerular damage in the kidney.In addition,kidney accumulated the highest content of cadmium,more than gills and liver.Expression of MT mRNA was increased in both liver and kidney of treated fish.Hepatic MT levels remained high after fish were removed to Cd-free water.In contrast,MT expression in kidney was peaked after 28 d of treatment and drastically dropped when fish were removed to Cd-free water.The high concentrations of Cd in hepatic tissues indicated an accumulation site or permanent damage on this tissue.     

Seed selections for crystallization of calcium phosphate for phosphorus recovery

Seed induces and promotes the crystallization of calcium phosphate, and acts as carrier of the recovered phosphorus （P）. In order to select suitable seed for P recovery from wastewater, three seeds including Apatite （AP）, Juraperle （JP） and phosphate-modified Juraperle （M-JP） were tested and compared. Batch and fixed-bed column experiments of seeded crystallization of calcium phosphate were undertaken by using synthetic wastewater with 10 mg/L P phosphate. It shows that AP has bad enduring property in the crystallization process, while JP has better performance for multiple uses, and M-JP is a hopeful seed for P recovery by crystallization of calcium phosphate.