Characterisation of FOGs in grease trap waste from the processing of chickens in Thailand

Industrial firms that kill and process chickens generate wastewater that contains fat, oil, and grease (FOG). The FOGs are located in the fatty waste that is collected by floatation in grease traps. Chemical and physical characterisation of FOGs would provide useful information that would help in the development of methods designed to decrease the extent of pollution caused by disposal of the waste and to utilise commercially some of its lipid constituents. Employing these methods would enhance the profitability and competitive potential of these commercial organisations. Samples of grease trap waste from 14 firms in central Thailand have been examined. Due to the very different schemes of waste management employed by these firms, the physical appearance of their fatty wastes showed considerable variation. The chemical and physical properties of the FOGs present in these wastes showed considerable variation also. Large amounts of free fatty acids (10–70% as oleic acid) were detected in most of the 14 wastes and palmitic, cis-9-oleic, cis,cis-9,12-linoleic, stearic, and palmitoleic acids were the predominant species of free and esterified acids. Most of the FOGs were solid at temperatures below 40 °C. Many of them contained traces of heavy metals (Cu and Pb) and some contained traces of the pesticides dimethoate and cypermethrin. The content of these potentially hazardous substances would have to be considered very carefully before discarding the fatty wastes and during the development of methods designed to isolate their potentially profitable lipid constituents.     

Use of thermal analysis techniques (TG-DSC) for the characterization of diverse organic municipal waste streams to predict biological stability prior to land application

The use of organic municipal wastes as soil amendments is an increasing practice that can divert significant amounts of waste from landfill, and provides a potential source of nutrients and organic matter to ameliorate degraded soils. Due to the high heterogeneity of organic municipal waste streams, it is difficult to rapidly and cost-effectively establish their suitability as soil amendments using a single method. Thermal analysis has been proposed as an evolving technique to assess the stability and composition of the organic matter present in these wastes. In this study, three different organic municipal waste streams (i.e., a municipal waste compost (MC), a composted sewage sludge (CS) and a thermally dried sewage sludge (TS)) were characterized using conventional and thermal methods. The conventional methods used to test organic matter stability included laboratory incubation with measurement of respired C, and spectroscopic methods to characterize chemical composition. Carbon mineralization was measured during a 90-day incubation, and samples before and after incubation were analyzed by chemical (elemental analysis) and spectroscopic (infrared and nuclear magnetic resonance) methods. Results were compared with those obtained by thermogravimetry (TG) and differential scanning calorimetry (DSC) techniques. Total amounts of CO₂ respired indicated that the organic matter in the TS was the least stable, while that in the CS was the most stable. This was confirmed by changes detected with the spectroscopic methods in the composition of the organic wastes due to C mineralization. Differences were especially pronounced for TS, which showed a remarkable loss of aliphatic and proteinaceous compounds during the incubation process. TG, and especially DSC analysis, clearly reflected these differences between the three organic wastes before and after the incubation. Furthermore, the calculated energy density, which represents the energy available per unit of organic matter, showed a strong correlation with cumulative respiration. Results obtained support the hypothesis of a potential link between the thermal and biological stability of the studied organic materials, and consequently the ability of thermal analysis to characterize the maturity of municipal organic wastes and composts.     

废聚苯乙烯的化学回收方法

废聚乙烯（ＰＳ）转化为燃料油和化学品的化学回收方法,分为废ＰＳ单独裂解及废ＰＳ与其它废塑料混合裂解两种方式,分别阐述了两种回收方式的研究成果和工艺现状,并就存在的问题进行了讨论。     

Potential of chicken by-products as sources of useful biological resources

By-products from different animal sources are currently being utilised for beneficial purposes. Chicken processing plants all over the world generate large amount of solid by-products in form of heads, legs, bones, viscera and feather. These wastes are often processed into livestock feed, fertilizers and pet foods or totally discarded. Inappropriate disposal of these wastes causes environmental pollution, diseases and loss of useful biological resources like protein, enzymes and lipids. Utilisation methods that make use of these biological components for producing value added products rather than the direct use of the actual waste material might be another viable option for dealing with these wastes. This line of thought has consequently led to researches on these wastes as sources of protein hydrolysates, enzymes and polyunsaturated fatty acids. Due to the multi-applications of protein hydrolysates in various branches of science and industry, and the large body of literature reporting the conversion of animal wastes to hydrolysates, a large section of this review was devoted to this subject. Thus, this review reports the known functional and bioactive properties of hydrolysates derived from chicken by-products as well their utilisation as source of peptone in microbiological media. Methods of producing these hydrolysates including their microbiological safety are discussed. Based on the few references available in the literature, the potential of some chicken by-product as sources of proteases and polyunsaturated fatty acids are pointed out along with some other future applications.     

A mathematical model to predict the composition and generation of hospital wastes in Iran

The aim of this study is to investigate the quality and quantity of hospital wastes in Iran. The generated hospital wastes have been estimated by the number of hospitals and the number of active beds in each province of Iran in 2001. All data and information have been gathered from: (i) Iran Statistics Center, (ii) literature review, and (iii) hospital waste investigations for an average hospital. Physical analyses have been conducted in terms of various materials (plastic, textile, paper, metal, and others) and components (biological, infectious, medical, and regular wastes). Based on the above-mentioned investigation and information, a mathematical model has been developed to calculate the generation of (infectious) hospital wastes for any desired year. Utilizing the model, generated infectious hospital wastes has been estimated as 698,937 tones for 2008 (short-term) and 3,494,387 tones for 2028 (long-term period). If the real infectious wastes are collected separately, then the generated infectious wastes will be reduced by 15.1% of the above-mentioned amount (139,787 tones for 2008, and 698,877 tones for 2028). Results of physical analysis show the components of the hospital waste as: (a) infectious, 67.3%; (b) medical, 8.8%; (c) biological, 1.8%; and (d) common municipal wastes, 22.1%. An appropriate collection method requires training the staff at hospitals along with preparation of the required facilities. Of course, both of these requirements are cost intensive.     

火炸药生产废水污染土壤修复的研究进展

总结了国内外化学修复法和生物修复法修复火炸药生产废水污染土壤的研究进展。比较了各种方法的优缺点,提出了未来火炸药生产废水污染土壤修复技术的研究方向。指出:应将物理修复法、化学修复法及生物修复法相结合,将修复定位于综合化、彻底化及可利用化,以期达到火炸药生产废水污染土壤的无害化治理。     

Techniques for the evaluation of maturity for composts of industrially contaminated lake sediments

Composting was applied as a bioremediation methodology for the reclamation of dredged sediments of Isnapur, Khazipally and Gandigudem lakes polluted with industrial wastes. The present study is an attempt to elaborate upon organic matter transformations and define the parameters for product maturity adapting chemical and spectroscopic methods during composting. The stability and maturity of sediments were evaluated by assessing parameters like C/N ratio, nitrification index (NH(4)-N/NO(3)-N), water-soluble organic carbon concentration, CO(2) evolution rate, cation exchange capacity and indices such as humification index, E4/E6 ratio, compost mineralization index (ash content/oxidizable carbon), germination index, dehydrogenase, polyphenoloxidase activities and FTIR spectroscopy. The results showed that the changes in the above chemical and biological parameters can be employed as reliable indicators of stability and maturity. The FTIR spectra revealed enrichment in the aromatic groups and a degradation of the aliphatic groups indicating stabilization of the final compost.     

Using a second-order polynomial model to determine the optimum dregs/bark ratio for industrial-biosolid composting: the initial conditioning stage.

Increasing pulp industry production has generated additional solid waste (i.e. biological sludge, dregs, etc.) and therefore an increasing disposal problem. On the other hand, composting is emerging as an interesting alternative for the disposal of residues. The objective of this study was to evaluate the physical and chemical properties of sludge, dregs and bark and the effect on their initial conditioning stage prior to composting, using pine chips as bulking agent. After their characterization, these solid wastes were combined in different mixture proportions defined by a 32 experimental design based on the response surface methodology (RSM), in which 18 observations were required for the independent variables (dregs and bark) and the C: N ratio, moisture content and pH were the dependent variables. The characterization indicated that the dregs have alkaline properties with the presence of some essential plant nutrients, such as phosphorous (0.37%), potassium (0.76%), magnesium (1.4%) and calcium (27%). The combination of the macronutrients (phosphorous: 0.39%, potassium: 0.24%, calcium: 1.7%, magnesium: 0.44%) and micronutrients such as ferrous material (0.47%) and zinc (0.12%) found in the sludge suggest a promising alternative despite the potential problem due to the high pH of the dregs. The RSM design indicated a feasible region that satisfied the optimal dregs: bark ratio of 0.25 without exceeding the addition of 12.5% dregs, due to the alkaline properties of these inorganic wastes and the quadratic influence over the C:N ratio. The experimental results indicated that the composting process of dregs, bark and sludge is technically suitable, although the use of a rapidly available C source needs to be evaluated.     

老化油处理技术研究进展

老化油是石油工业生产过程中产生的含大量化学药剂、水、黏土及无机盐的状态稳定的复杂乳液,其产生量大、处理难度高。介绍了老化油的来源、成分、数量、对生产的危害、特点及处理难点,总结了老化油现有的处理方法,包括物理法、化学法、生物法及组合工艺,分析了各种方法的优缺点,并对老化油的管理和研究方向提出了建议。     

含硝基苯类化合物废水处理技术研究进展

综述了近年来处理含硝基苯类化合物废水的物理法（包括吸附法和溶剂萃取法）、化学法（包括电化学法、铁碳微电解法、超声波氧化法和臭氧氧化法及复合技术）和生物法的研究进展。指出将现有的处理技术高效整合并降低成本是今后处理含硝基苯类化合物废水的研究方向和重点。     

Medical wastes characterisation in healthcare institutions in Mauritius

This study was initiated to characterize solid and liquid wastes generated in healthcare institutions and to provide a framework for the safe management of these wastes. The project was carried at three major medical institutions, namely, the Jeetoo Hospital, the Sir Seewoosagur Ramgoolam National (SSRN) Hospital and the Clinic Mauricienne. A waste audit carried out at these sites revealed that approximately 10% of solid wastes was hazardous in nature, consisting mainly of infectious, pathological and chemical wastes. The average amount of hazardous wastes per patient per day was found to be 0.072 kg at Jeetoo hospital, 0.091 kg at SSRN hospital and 0.179 kg at the clinic. The amount of hazardous wastes generated as a function of the number of occupied beds was found to follow a relationship of type y=0.0006x-0.19, where y was the amount of hazardous wastes generated per bed per day and x was the number of occupied beds. The waste quantifying process also revealed that at SSRN Hospital, 0.654 m(3) of water was being consumed per patient per day and the amount of wastewater produced was 500 m(3)/day. Further analysis revealed that the wastewater was polluting with chemical oxygen demand (COD), biological oxygen demand (BOD(5)), total suspended solids (TSS) and coliform content well above permissible limits.     

Superfund site remediation by landfilling—overview of landfill design,operation, closure,and postclosure issues

This article discusses the appropriateness of using landfills as part of remediating hazardous chemical and Superfund sites, with particular emphasis on providing for true long‐term public health and environmental protection from the wastes and contaminated soils that are placed in the landfills. On‐site landfilling or capping of existing wastes is typically the least expensive approach for gaining some remediation of existing hazardous chemical/Superfund sites. The issues of the deficiencies in US EPA and state landfilling approaches discussed herein are also applicable to the landfilling of municipal and industrial solid “nonhazardous” wastes. These deficiencies were presented in part as “Problems with Landfills for Superfund Site Remediation” at the US EPA National Superfund Technical Assistance Grant Workshop held in Albuquerque, New Mexico, in February 2003. They are based on the author's experience in investigating the properties of landfill liners and the characteristics of today's landfills, relative to their ability to prevent groundwater pollution and to cause other environmental impacts. Discussed are issues related to both solid and hazardous waste landfills and approaches for improving the ability of landfills to contain wastes and monitor for leachate escape from the landfill for as long as the wastes in the landfill will be a threat. © 2004 Wiley Periodicals, Inc.     

Synthesis of unsaturated polyester resin from glycolysed postconsumer PET wastes

The purpose of this study was to explore ways to extend the chemical recycling of poly(ethylene terephthalate) (PET) as a valuable feedstock for chemical processes. First, PET wastes were depolymerised using a glycolysis method in the presence of sodium carbonate, which is considered to be a less environmentally damaging option for a catalyst. Good yields of the monomer bis(2-hydroxyethyl) terephthalate (BHET) were obtained (80 %). Second, to develop an economically viable recycling programme for the reclaimed BHET, the conversion of purified BHET into unsaturated polyester resins (UPR) was studied. The recovered monomer was thus polyesterified with maleic anhydride and subsequently mixed with styrene monomer to prepare UPRs. The resins were casted by a crosslinking reaction using methyl ethyl ketone peroxide and cobalt 2-ethylhexanoate as the initiator and catalyst, respectively. The polyesterification reaction was followed by gel permeation chromatography. The curing process was studied by differential scanning calorimetry and infrared spectroscopy. The cured resin was subjected to various characterisation methods in order to determine its chemical, physical and mechanical properties. Resins with suitable properties for commercial application were obtained.     

Potential useful products from solid wastes

Wastes have been aptly defined as “items i.e. resources, that have been discarded because their possessors no longer have an apparent use for them”. Accordingly, “wastes” have a significance only in relation to the items and those who have discarded them. The discarded items now are resources awaiting reclamation. Reclamation usually involves either salvage or conversion—or in modern terminology, “reuse” or “recycling”. Reclamation for reuse consists in refurbishing or other upgrading without significantly altering original form and composition. Examples of wastes amenable to reuse are containers (bottles, etc.), cartons and repairable tires. With “recycling” (i.e. conservation), the discarded items are processed such that they become raw material i.e. resources in the manufacture of “new” products. The variety of processes is wide, ranging from simply physical (grinding) through thermal (melting, gasification, combustion), to biological (composting, biogasification, hydrolysis, microbial protein production). In the paper, reuse and recycling (conversion) are evaluated in terms of advantages and disadvantages (limitations) and their respective technologies are described and discussed in detail.     

污水处理固体废弃物污泥的处置方法研究

从生活污水处理工艺出发介绍污泥产生的环节,探究污泥传统处置方法和资源化处置方法,同时对污泥源头减量化方法做了详细论述,最后分析了污泥处置成本的影响因素,对污泥环保处置提供参考与帮助。     

An ecotoxic risk assessment of residue materials produced by the plasma pyrolysis/vitrification (PP/V) process

Plasma is the fourth state of matter, following the three states of solid, liquid and gas. Experience has amply demonstrated that solids exposed to the oxygen-deficient plasma flame are converted to liquid, and liquid exposed to the same flame is converted to gas. A low amount of vitrified solid residue material usually remains at the end of this process. Plasma pyrolysis/vitrification (PP/V) has been demonstrated as a safe, efficient, cost-effective technology for the treatment of wastes, including hazardous wastes. Besides the low amounts of gaseous byproducts that PP/V produces, the solid vitrified residue presents a low leachability of pollutants. Studies have been performed in many countries in order to assess the leachability of chemical substances. But from the results of identified studies, none has reported results on the ecotoxicological properties of the leachates. The aim of this study was to contribute to the assessment of ecotoxic risk of four different vitrified materials. Vitrified samples of contaminated soils, municipal solid wastes, and incinerator bottom ashes were submitted to the European leaching pre-standard test number prEN 12457-2. The leachates were analyzed for 22 chemical parameters. The biological characterization comprised the assessment of bioluminescence inhibition of Photobacterium phosphoreum bacterium, growth inhibition of Pseudokirchneriella subcapitata algae and the germination inhibition of Lactuca sativa vegetable. The chemical and ecotoxicological results were analyzed according to the French proposal of Criteria on the Evaluation Methods of Waste Toxicity (CEMWT) and a Toxicity Classification System (TCS). The chemical and ecotoxicological results indicated a low leachability of pollutants and a low toxicity level of leachates. All samples studied were as below the TCS class 1 level (no significant toxicity observed) and as non-ecotoxic for CEMWT. Therefore, the environmental ecotoxic risk of the analyzed vitrified samples was determined to be very low.     

Properties of slate mining wastes incubated with grape marc compost under laboratory conditions

The effect of the addition of spent grape marc compost (GMC) and vermicompost (GMV) as amendments to slate mining wastes was evaluated in a laboratory incubation experiment. Mixtures of slate processing fines (SPF), with three doses of each amendment (4%, 8% and 16% compost, dry weight), plus a control were incubated at 25 degrees C in the laboratory for 90 days. The changes in the chemical and biological properties of the mixtures (pH, total C, total N, inorganic N, available nutrients, microbial biomass carbon and dehydrogenase activity) were investigated during the incubation period, and once it was finished, the phytotoxicity of the mixtures was determined by the germination of Lolium multiflorum Lam. seeds. The addition of the amendments significantly increased the nutrient concentrations of the SPF and enhanced biological activity by increasing microbial biomass and enzymatic activity. Results improved with higher doses; within the composts, GMV showed a better performance than GMC. These results prove the suitability of grape marc-derived amendments for the biochemical amelioration of mining wastes, and highlight the benefits of organic amendment in restoration projects.     

DISCRISET: A battery of tests for fast waste classification – Application of tests on waste extracts

The Hazardous Waste Directive (HWD, Council Directive 91/689/EC, 1991) provides a framework for classification of hazardous waste, based on 15 Hazard (H)-criteria. For complex wastes the HWD foresees the application of toxicity tests on the waste material itself to assess its toxic properties. However, these proposed test methods often involve mammalian testing, which is not acceptable from an ethical point of view, nor is it feasible economically. The DISCRISET project was initiated to investigate the use of alternative chemical and biological fast screening tests for waste hazard classification. In the first part of the project, different methods were reviewed and a testing strategy was proposed to minimize time and cost of analysis by a tiered approach. This includes as a first tier chemical analysis followed by a general acute toxicity screen as a second tier and as a third tier mechanistic toxicity tests to assess chronic toxicity (genotoxicity, hormone disturbance, teratogenic effects, immunologic activity). In this phase of the project, selected methods were applied to 16 different waste samples from various sources and industries. The first tier chemical tests are recommended for the full characterization of the leachate fraction (inorganics) but not for the organic fraction of samples. Here the chemical characterization is only useful if toxic content is known or suspected. As second tier the fast bacterial test Microtox is validated as a general toxicity screen for the organic fraction (worst case organic extract). Samples that are not classified in tier 1 or 2 are then further investigated in the third tier by the mechanistic toxicity tests and tested for their potential chronic toxicity: immune activity (TNF-α upregulation) is indicative for corrosive, irritating or sensitising effects (H4/H8/H15), reproductive effects (H10) are indicated by hormone disturbance and early life stage abnormalities in fish larvae when exposed to the extracts and mutagenicity and carcinogenicity (H7, H11) are indicated by SOS response induction and increased mutation frequency in the Ames test when exposed to the extracts. Results indicate that the combination of chemical tests and bioassays allows important hazardous properties to be addressed and the tiered approach ensures that the tests are performed quickly and economically. The suggested strategy provides a solid and ethical alternative to the methods described in the HWD and is a vast improvement on the current, arbitrary classification.     

Co-disposal of hazardous and municipal wastes in landfills: Experimental work

During the past 15 years considerable research has taken place in the U.K. to investigate the decomposition processes occurring within municipal waste landfills. This, in turn, has led to a better understanding of the environmental fate of many industrial wastes currently, or formerly, co-disposed with municipal refuse. Codisposal is defined in this paper as the disposal of chemical wastes in an admixture with domestic waste so that full advantage is taken of the attenuation and biochemical processes operating within a landfill to reduce the environmental impact to an insignificant level. Central to this philosophy is the maintenance of a balanced input of different wastes to ensure that attenuation and degradation processes are not overwhelmed. It is contended that co-disposal is an effective disposal option for a wide range of industrial wastes at correctly sited and well managed landfills.Co-disposal research findings for three selected industrial waste types are presented and related to the scientific basis for the prohibition, or continuation of their disposal to landfills.