Removal of carbon constituents from hospital solid waste incinerator fly ash by column flotation

Hospital solid waste incinerator (HSWI) fly ash contains a large number of carbon constituents including powder activated carbon and unburned carbon, which are the major source of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in fly ash. Therefore, the removal of carbon constituents could reduce PCDD/Fs in fly ash greatly. In this study, the effects of the main flotation parameters on the removal of carbon constituents were investigated, and the characteristics of the final product were evaluated. The results showed that loss on ignition (LOI) of fly ash increased from 11.1% to 31.6% during conditioning process. By optimizing the flotation parameters at slurry concentration 0.05 kg/l, kerosene dosage 12 kg/t, frother dosage 3 kg/t and air flow rate 0.06 m³/h, 92.7% of the carbon constituents were removed from the raw fly ash. Under these conditions, the froth product has LOI of 56.35% and calorific values of 12.5 MJ/kg, LOI in the tailings was below 5%, and the total toxic equivalent (TEQ) of PCDD/Fs decreased from 5.61 ng-TEQ/g in the raw fly ash to 1.47 ng-TEQ/g in the tailings. The results show that column flotation is a potential technology for simultaneous separation of carbon constituents and PCDD/Fs from HSWI fly ash.     

Use of fly ash for the removal of phenol and its analogues from contaminated water

This work attempts to elucidate the effects of different operational variables affecting the mechanistic function of fly ash for removal of some priority organic pollutants viz. phenol and its analogues. Thermodynamic parameters like free energy change, enthalpy and entropy of the process, as well as the sorption isotherms for phenols on fly ash, were measured and the most suitable isotherm was determined. Results of the study indicate that the extent of solute removal is determined by the initial solute concentration, molecular size and molecular arrangement of the solute. At the fixed set of experimental conditions, a model equation can be developed from which the percent removal corresponding to the load of the particular solute is determined. It is assumed that the mechanism of adsorption is governed by the surface characteristics of fly ash; pH has a vital role in influencing the solute removal as both the ionizing power (acidity, pKa) of the solutes and the zero point charge of fly ash (pH(ZPC)) depend on the solution pH. Isotherm pattern and the free energy change indicate that the process is favorable, as well as spontaneous. The information gathered from the study will serve as a predictive modeling procedure for the analysis and design of the removal of organic pollutants and decontamination of water. The leaching experiment indicates that the retained solutes do not release from fly ash. The retained solutes can be recovered and utilized as industrial raw material.     

Classification and categorization of treatment methods for ash generated by municipal solid waste incineration: A case for the 2 greater metropolitan regions of greece

The primary goal of managing MSW incineration residues is to avoid any impact on human health or the environment. Incineration residues consist of bottom ash, which is generally considered as rather harmless and fly ash which usually contains compounds which are potentially harmful for public health. Small quantities of ash (both bottom and fly) are produced currently in Greece, mainly from the healthcare waste incineration facility in Attica region. Once incineration plants for MSW (currently under planning) are constructed in Greece, the produced ash quantities will increase highly. Thus, it is necessary to organize, already at this stage, a roadmap towards disposal/recovery methods of these ash quantities expected.Certain methods, related to the treatment of the future generated ash which are more appropriate to be implemented in Greece are highlighted in the present paper. The performed analysis offers a waste management approach, having 2016 as a reference year for two different incineration rates; 30% and 100% of the remaining MSW after recycling process. The results focus on the two greater regions of Greece: Attica and Central Macedonia. The quantity of potential future ash generation ranges from 137 to 459 kt for Attica region and from 62 to 207 kt for central Macedonia region depending on the incineration rate applied. Three alternative scenarios for the treatment of each kind of ash are compiled and analysed. Metal recovery and reuse as an aggregate in concrete construction proved to be the most advantageous -in terms of economy-bottom ash management scenario. Concerning management of the fly ash, chemical treatment with phosphoric solution addition results to be the lowest total treatment cost and is considered as the most profitable solution. The proposed methodology constitutes a safe calculation model for operators of MSW incineration plants regardless of the region or country they are located in.     

The adsorption characteristics of heavy metals by various particle sizes of MSWI bottom ash

The incineration rate of municipal solid waste (MSW) has been increased because of difficulty in securing a proper disposal site for MSW in Korea. The advantage of incineration is reduction of the volume of waste; however, significant amounts of bottom ash and fly ash were generated in the incineration process. Their treatment has attracted growing interest because of the potential toxicity of hazardous heavy metals. Generally, heavy metals are less released from bottom ash than from fly ash. In this study the adsorption characteristics of heavy metals were investigated using various particle sizes of MSWI bottom ash. Since bottom ash has a broad particle size distribution, it was sieved to size classes of +20, -20, -48, -80, -100 mesh. Cation exchange capacity (CEC) was analyzed by the ammonium acetate method to evaluate the potential as an adsorbent. The CEC values and surface areas increase as the range of particle size becomes finer. The adsorption experiment was conducted using synthetic (Cu and Ni) and plating rinse water as a function of reaction time (10-180 min), liquid/solid ratio (2-100) and particle size (+20 to -100 mesh), respectively. The adsorption rate increased with decreasing particle size and with increasing liquid/solid ratio; however, the removal efficiency of Cu was higher than that of Ni. In the case of plating rinse water, the adsorption rate decreased sharply at high liquid/solid ratio, and it showed over 80% of adsorption rates for Cu and Ni at an initial pH of 3.     

Chloride extraction for quality improvement of municipal solid waste incinerator ash for the concrete industry.

Coal ash from power stations has long been used successfully in the cement industry as binders in several Portland formulations. This is not the case for municipal solid waste (MSW) ash as chloride concentrations, ranging from 10 to 200 g kg(-1) dry weight in the bottom and fly ash, respectively, exceed the maximum allowable concentration in most cement mixtures. To reduce chloride content in MSW bottom ash, a laboratory investigation was carried out based on the exhaustive washing in tap water. The influence of operative parameters such as temperature, granulometric properties and solid/liquid ratio of extraction was evaluated. In addition to optimization of the mentioned operative parameters for full-scale application, the paper gives preliminary indications on mechanistic aspects of the washing operation.     

Leachability of municipal solid waste ashes in simulated landfill conditions

In Japan the volume of municipal solid waste is reduced by incineration, with fly ash and bottom ash disposed in controlled landfills. The leachability of anions and heavy metal cations, Zn, Cu and Pb, from MSW fly ash and bottom ash at different pHs was examined using batch- and column-leaching tests. The MSW ashes had a high capacity for neutralizing acids. Behaviour during leaching depended on the pH of the solution. For the volumes applied, the leachabilities of MSW fly ash were very similar at pHs from 3 to 6. Due to its amphoteric nature, Pb is leachable at pHs of approximately 10 or more, with leachate concentrations of about 3 and 3-10mg/L for the fly ash and bottom ash, respectively, much higher than for Zn and Cu. Pb concentrations for most leaching solutions were 1 and 3mg/L for the fly ash and bottom ash, respectively. Zn, and Cu leached at low concentrations for solutions of pH 3-6. Na and K ions leached at high concentrations of approximately 5000 mg/L in the first batch leaching test, decreasing to 10mg/L by the fourth leach. Ca and Mg ions leached more gradually than Na and K. Cl(-) and SO(4)(2+) ions were the major anions in the MSW ash. The high pH and cation leaching are expected to have negative impacts on the performance of clay liners.     

Use of zeolitised coal fly ash for landfill leachate treatment: a pilot plant study

Treatment of municipal solid waste (MSW) landfill leachate generally results in low percentages of nutrient removal due to the high concentration and accumulation of refractory compounds. For this reason, individual physical, chemical and biological processes have been used for the treatment of raw landfill leachate and sometimes for the mixture of domestic wastewater and landfill leachate. In this work, the possibility of treating landfill leachate was tested in a bench-scale pilot plant by a two-step method combining adsorption and coagulation-flocculation. Zeolite synthesized from coal fly ash, a by-product of coal-fired power stations, was used in this study both as a decantation aid reagent and as an adsorbent of COD and NH4-N. The coagulation-flocculation step was performed by the use of aluminium sulphate and a polyelectrolyte (ACTIPOL A-401). The leachate was collected directly from a storage unit of the organic fraction of MSW, before it was composted. For this reason the raw leachate was diluted before treatment. The sludge was recirculated to enhance the removal efficiency of nutrients as well as to optimize flocculant saving and to decrease sludge production. The results showed that it is possible to remove 43%, 53% and 82% of COD, NH4-N, and suspended solids, respectively. Therefore, this method may be an alternative for ammonium removal, as well as a suitable pre- or post-treatment step, in combination with other processes in order to meet regulatory limits.     

Recycling of municipal solid waste incinerator fly ash by using hydrocyclone separation

The municipal solid waste incinerators (MSWIs) in Taiwan generate about 300,000 tons of fly ash annually, which is mainly composed of calcium and silicon compounds, and has the potential for recycling. However, some heavy metals are present in the MSWI fly ash, and before recycling, they need to be removed or reduced to make the fly ash non-hazardous. Accordingly, the purpose of this study was to use a hydrocyclone for the separation of the components of the MSWI fly ash in order to obtain the recyclable portion. The results show that chloride salts can be removed from the fly ash during the hydrocyclone separation process. The presence of a dense medium (quartz sand in this study) is not only helpful for the removal of the salts, but also for the separation of the fly ash particles. After the dense-medium hydrocyclone separation process, heavy metals including Pb and Zn were concentrated in the fine particles so that the rest of the fly ash contained less heavy metal and became both non-hazardous and recyclable.     

Optimizing Cr(VI) adsorption on activated carbon produced from heavy oil fly ash

In order to explore the beneficial utilization of heavy oil fly ash (HOFA) generated in the power plants, the present study is intended to optimize the chromium(VI) [Cr(VI)] adsorption on activated carbon produced from HOFA. The raw HOFA obtained from a power plant was washed by nitric/hydrochloric acid and activated at 800 °C with a holding time of 60 min to produce fly ash activated carbon (FAC). Phosphoric acid was used as a chemical agent to improve the surface characteristics of the HOFA during the activation process. Batch adsorption experiments were employed to evaluate the effects of different parameters such as initial Cr(VI) concentration, pH, and FAC dose on the removal of Cr(VI) from aqueous solution. A total of 17 adsorption experimental runs were carried out employing the detailed conditions followed the response surface methodology based on the Box–Behnken design. The results indicate that developed FAC has the potential for removing Cr(VI) from wastewater. Under the test conditions, a maximum of 91.51 % Cr(VI) removal efficiency was achieved.     

Characterization of PCDD/Fs and heavy metals from MSW incineration plant in Harbin

The characterization of PCDD/Fs and heavy metals in the flue gas and fly ash of Harbin municipal solid waste (MSW) incineration plant, located in the northeast of China, was investigated in this study. The MSW was treated in a twin internal fluidized (TIF) bed incinerator. The results indicate that the emission of PCDD/Fs into the environment is 0.02 ng I-TEQ/m3 and the level of PCDD/Fs in the fabric filter fly ash is 0.7982 ng I-TEQ/g. The leachability levels of Pb, Cd and Hg in the fly ash are below the limits of environmental protection standard in China. However, the contents of Cu, Zn, and Hg are high in the fly ash. This suggests that the fly ash is a hazardous waste that requires special treatment and disposal. The practice of more than four years of operation shows that the TIF bed incinerator is very suitable and practical for China.     

Heavy metals removal/stabilization from municipal solid waste incineration fly ash: a review and recent trends

Waste treatment using thermal technologies, such as incineration, leads to the production of pollutants and wastes, including fly ash (FA). Fly ash contains heavy metals (HMs) and other contaminants and can potentially pose high risks to the environment and negatively impact health and safety. Consequently, stabilizing fly ash prior to either use or landfilling is crucial. The toxicity of fly ash through heavy metal leaching can be assessed using leaching tests. The leaching rates of heavy metals primarily depend on the surrounding conditions as well as fly ash properties and metal speciation. Physical separation, leaching or extraction, thermal treatment and solidification/chemical stabilization are proposed as suitable approaches for fly ash treatment. Economic considerations, environmental concerns, energy consumption and processing times can define the efficiency and selection of the treatment approach. This review considers the latest findings and compares the advantages and shortcomings of different fly ash treatment methods with the aim of highlighting the recent advances in the field. The review concludes that the simultaneous implementation of various methods can lead to highly efficient heavy metals removal/stabilization while simultaneously taking economic and environmental considerations into account.

     

Distribution of remaining Cd in MSWI fly ash washed with nitric acid

Municipal solid waste incineration (MSWI) fly ash is by-product and hazardous waste produced from MSWI plant. In the MSWI fly ash there are high contents heavy metals, among which cadmium (Cd) is more active and toxic. Although inorganic acid leaching is an effective way to remove heavy metals out from the MSWI fly ash and nitric acid has great efficiency for Cd removal, little literature reported the redistribution of remaining Cd in the MSWI fly ash. This investigation focused on the change of different factions (exchangeable, bound to carbonates, bound to Fe–Mn oxides, bound to organic matter and residual) of Cd in treated (i.e. washed with nitric acid) MSWI fly ash. Sequence extraction procedures (SEP) have been used to derive different fractions of Cd, results indicated that fractions of Cd have changed significantly after nitric acid washing procedures. Due to the changes of main compounds and microstructures stable Cd (bound to organic matter and residual) had opportunity to leach out, which resulted in a higher potential risk (or higher bioavailability index) for living creatures, although the total amount of Cd decreased. X-ray diffraction (XRD) and images of scanning electron microscope (SEM) proved these changes in washed MSWI fly ash.     

Potential use of lignite fly ash for the control of acid generation from sulphidic wastes

In the present paper, the potential use of lignite fly ash in the control of acid generation from sulphidic tailings disposed of at Lavrion, Greece was studied. Long-term laboratory column kinetic tests were performed on tailings containing 27% S, which were homogeneously mixed with various amounts of fly ash, ranging from 10 to 63% w/w. The drainage quality of the columns was monitored over a test period of 600 days. Chemical and mineralogical characterisation of column solid residues was performed after a 270-day test period. The hydraulic conductivity of the mixtures was also measured to evaluate the potential of fly ash to form a low permeability layer. Based on the results, the addition of fly ash to sulphidic tailings, even at the lower amount, increased the pH of the drainage at values of 8.6-10.0 and decreased the dissolved concentrations of contaminants, mainly Zn and Mn, to values that meet the European regulatory limits for potable water. Higher fly ash addition to tailings, at amounts of 31 and 63% w/w also reduced the water permeability of material from 1.2 x 10(-5) cm/sec to 3 x 10(-7) and 2.5 x 10(-8) m/s, respectively.     

Diopside-based glass-ceramics from MSW fly ash and bottom ash

By utilising MSW fly ash from the Shanghai Yuqiao municipal solid waste (MSW) incineration plant as the main raw material, diopside-based glass-ceramics were successfully synthesized in the laboratory by combining SiO(2), MgO and Al(2)O(3) or bottom ash as conditioner of the chemical compositions and TiO(2) as the nucleation agent. The optimum procedure for the glass-ceramics is as follows: melting at 1500 degrees C for 30 min, nucleating at 730 degrees C for 90 min, and crystallization at 880 degrees C for 10h. It has been shown that the diopside-based glass-ceramics made from MSW fly ash have a strong fixing capacity for heavy metals such as lead (Pb), chromium (Cr), cadmium (Cd) etc.     

Lysimeter washing of MSW incinerator bottom ash

Stockpiled municipal waste incinerator bottom ash is frequently considered for utilization as a construction material. Two 360 kg lysimeter experiments were conducted to study percolation washing of contaminants from stockpiled MSW bottom ash. One lysimeter was leached with a concentrated sodium hydroxide solution, as a possible pre-treatment for improvement of the bottom ash characteristics prior to utilization, while the other was leached using distilled water. The lysimeter leachate was analysed, and at the end of the 2-year leaching period, the bottom ash from each lysimeter was subjected to several laboratory tests to assess the effect of the treatments. The laboratory tests showed that distilled water leachability of both treated ashes was an order of magnitude lower than that of fresh ash, but long-term contaminant leachability under acidic conditions had not changed. Although alkaline washing clearly resulted in greater contaminant removal than did distilled water washing, the chemical properties of the alkaline-leached bottom ash were not significantly different from those of the water-leached ash.     

Occurrence of phenols in leachates from municipal solid waste landfill sites in Japan

The concentrations of 41 phenols in leachates from 38 municipal solid waste (MSW) landfill sites in Japan were measured. The main phenols detected in leachates were phenol, three cresols, 4-tert-butylphenol, 4-tertoctylphenol, 4-nonylphenol, bisphenol A, and some chlorophenols. The concentration levels of phenols were affected by the pH values of the leachates and the different types of landfill waste. The origins of phenol and p-cresol were considered to be incineration residues, and the major origin of 4-tert-butylphenol, bisphenol A, and 2,4,6-trichlorophenol was considered to be solidified fly ash. In contrast, the major origins of 4-tert-octylphenol and 4-nonylphenol were considered to be incombustibles. The discharge of leachates to the environment around MSW landfill sites without water treatment facilities can cause environmental pollution by phenols. In particular, the disposal of incineration residues including solidified fly ash and the codisposal of solidified fly ash and incombustibles might raise the possibility of environmental pollution. Moreover, the discharge of leachates at pH values of 9.8 or more could pollute the water environment with phenol. However, phenol, 4-nonylphenol, and bisphenol A can be removed to below the con centration levels that impact the environment around landfill sites by a series of conventional water treatment processes.     

Effects of the type of sintering atmosphere on the chromium leachability of thermal-treated municipal solid waste incinerator fly ash

The sintering process offers an opportunity to combine detoxification and resource recovery for the treatment of municipal solid waste (MSW) incinerator fly ash. However, the chromium (Cr) in the sintered fly ash becomes more readily leachable with increasing sintering time and temperature, thus posing severe threats to the environment and human health when the sintered ash is recycled or reused. This study investigated the enhanced leachability of fly ash containing Cr, by heating the chromium (III) oxide (Cr2O3)-spiked fly ash to 800 degrees C in atmospheres containing air, nitrogen gas (N2), and 5% H2 + 95% N2, respectively. The results indicated that trivalent chromium was converted to its soluble hexavalent form during sintering in the air atmosphere; whereas sintering in a nitrogen atmosphere significantly reduced the leachability of Cr due to lack of oxygen (O2) to oxidize. The effects of the sintering temperature on the total chromium content and the leaching concentration in the toxicity characteristic leaching procedure (TCLP) extract are also discussed.     

Leaching behaviour of elements and evaluation of pre-treatment methods for municipal solid waste incinerator residues in column leaching tests.

Two new pre-treatment methods (water-washing/carbonation and carbonation/phosphate stabilization) of municipal solid waste (MSW) incinerator residues were evaluated by column leaching tests under aerobic conditions and anaerobic conditions (which were changed to aerobic conditions after 10 months). A mixture of bottom ash and fly ash (5:1 ratio) was pre-treated using each method. Shredded incombustible residues (SIR) were added to each ash preparation in proportions similar to the ratios present in landfills. For comparison, landfill wastes typical of Japan, namely, a mixture of bottom ash, chelating-pre-treated fly ash, and SIR, were also examined. Leachate samples were collected periodically and analysed over a 15-month period. When compared with chelating pretreatment, both water-washing/carbonation and carbonation/ phosphate stabilization reduced the leaching of Pb, Al, and Cu by about one to two orders of magnitude. Moreover, the initial concentrations of Ca and Pb in leachates from column of water-washing/carbonation were 56-57% and 84-96% less than those from the column of carbonation/phosphate stabilization. Therefore, water-washing/carbonation was considered to be a promising approach to obtain early waste stabilization and to reduce the release of heavy metals to near-negligible levels. The leaching behaviour of elements was also discussed.     

粉煤灰的改性、成型及深度除磷应用

选择合适的改性剂对粉煤灰进行改性,通过有机高分子交联方法对改性粉煤灰进行成型处理,并采用静态吸附法评价改性粉煤灰的深度除磷效果。采用1 g氢氧化铝改性粉煤灰处理100 mL磷质量浓度为10.0 mg/L的模拟废水,磷去除率可达99.70％,处理后模拟废水中磷质量浓度低于0.50 mg/L, 达到GB8978-1996《污水综合排放标准》。成型处理可提高粉煤灰的沉降速率,改善灰水分离效果。经超声再生后的成型氢氧化铝改性粉煤灰的磷去除率仍可达67.9％。     

Production of cement clinkers from municipal solid waste incineration (MSWI) fly ash

This communication reports the laboratory scale study on the production of cement clinkers from two types of municipal solid waste incineration fly ash (MSW ash) samples. XRD technique was used to monitor the phase formation during the burning of the raw mixes. The amount of trace elements volatilized during clinkerization and hydration, as well as leaching behaviours of the clinkers obtained from optimum compositions, were also evaluated. From the results it is observed that all of the major components of ordinary Portland cement (OPC) clinkers are present in the produced clinkers. Results also show the volatilization of considerable amounts of Na, K, Pb, Zn and Cd during the production of clinkers. However, major parts of the toxic elements remaining in the clinkers appear to be immobilized in the clinkers phases. Hydration studies of the clinkers obtained from optimum compositions show that the clinkers prepared from raw MSW ash are more reactive than the washed MSW ash based clinkers. TG/DTA analyses of the hydrated pastes show the formation of hydration products, which are generally found in OPC and OPC derived cements. The initial study, therefore, shows that more than 44% of MSW ash with the addition of very small amounts of silica and iron oxide can be used to produce cement clinkers. The amount of CaCO3 necessary to produce clinkers (approximately 50%) is also smaller than the same required for the conventional process (more than 70%).