微生物监测在啤酒工业废水处理中的应用

采用活性污泥工艺处理啤酒工业废水,通过长期对活性污泥生物相中主要微生物的监测：表明其种类和数量变化与处理系统进出水水质变化密切相关。以此了解系统运行状况、判断工艺故障,获得了满意效果     

微生物监测在啤酒工业废水处理中的

采用活性污泥工艺处理啤酒工业废水，通过长期活性污泥生物相中主要微生物的监测：表明其种类和数量变化与处理系统进出水水质变化密切相关，以此了解系统运行状部位民工艺故障，获得了满意效果。     

造纸废水处理改造工程分析

对造纸企业原有废水处理工艺及处理设施进行分析和改造,采用浮动延时曝气活性污泥工艺处理造纸废水。实践证明,改造工程处理后的水质可以满足《污水综合排放标准》(GB 8978-1996)二级标准。     

苯系化合物好氧生物降解性实验研究

通过使用EJD－1和活性污泥2种菌源，在好氧振荡瓶和好氧曝气池中研究苯、甲苯、邻二甲苯、间二甲苯、对二甲苯的降解情况。研究结果表明，EJD－1对甲苯有较好的降解效果，活性污泥中有大量苯系化合物的降解菌，也有难降解污染物邻二甲苯的降解菌。可以通过好氧振荡瓶培养法来选择好氧曝气池处理法的工艺参数。     

浅谈活性污泥在废水处理中的应用

活性污泥法是如今进行污水处理的主要手段之一。本文主要论述活性污泥法进行污水处理的原理以及工艺流程,并对活性污泥法处理污水过程中所暴露出的种种问题进行一一阐述,并提出一些可行的解决方案。     

SBR、PAC-SBR反应器处理制药废水污泥变化特征

本文探讨了SBR和PAC-SBR反应器处理盐酸林可霉素原料液生产废水过程中活性污泥特征的变化．随着废水投加量的增加，PAC-SBR反应器的污泥性能始终优于SBR反应器，但是由于盐酸林可霉素原料液生产废水对生物较强的抑制作用，PAC-SBR反应器和SER反应器中污泥的活性均发生恶化，COD去除率已明显下降，单独采用SBR或PAC-SBR法处理已难以达到排放标准，必须进行工艺的组合．PAC-SBR反应器较SBR反应器在污泥性质及处理效率上均有一定的改善，处理盐酸林可霉素原料药生产废水有一定的优势．     

二沉池设计在印染污水处理中的应用

以南通三喜织染有限公司污水处理改造工程为例，阐述生物氧化，挂膜接触和活性污泥回流的复式好氧工艺，增设二沉池、均质、均量池、池底污泥回流，增加生物量，提高生化法处理染色污水的效果．     

氟喹诺酮类抗生素在水环境中的去除研究综评

介绍了水环境中氟喹诺酮类抗生素的危害,分析了其在污泥吸附、微生物降解和光降解作用下的去除机理。综述了去除氟喹诺酮类抗生素的常规处理技术（活性污泥法和人工湿地）、深度处理技术（高级氧化和膜处理）,以及新型处理技术（超声降解、土壤渗滤系统和生物电强化）的研究进展与优劣,指出不同反应体系的去除机理和途径不一致,需要针对多相、多污染介质的复杂实际环境开展进一步研究。     

城市污水处理厂参数自动监测中应注意的问题

城市污水处理厂参数自动监测中应注意的问题田伟根（苏州河道管理处苏州２１５００４）现就城市污水处理厂参数自动监测中应注意的几个问题作一些分析。１传感器组数及按装位置的确定在活性污泥法中,曝气池是污水处理的核心部分,运行中应根据有关参数的变化来调整工艺运...     

微波消解—原子吸收/原子荧光光度法测定活性污泥中的Cd、Pb、Ni、Cu、Zn、Cr、K、As、Hg

通过实验,建立了活性污泥中金属和重金属的测定方法。活性污泥样品经硝酸—氢氟酸或硝酸—高氯酸微波消解处理后,Pb、Ni、Cu、Zn、Cr、K选用火焰原子吸收分光光度法测定,Cd用石墨炉原子吸收分光光度法测定,As、Hg用原子荧光光度法测定。该方法操作简单,结果准确,重现性好。样品加标回收率为93%-108%,相对标准偏差〈5%。     

COD adsorption capacity of the activated sludge — Its determination and application in the activated sludge process

Proper control of the activated sludge process is essential in ensuring production of good effluent. COD adsorption capacity (CAC) of the activated sludge could be used as a control parameter. CAC is determined by mixing the activated sludge with the settled sewage and measuring the instantaneous COD reduction per unit mass of activated sludge. CAC measures substrate removal by physical adsorption and reflects the quality of the activated sludge. CAC of a healthy activated sludge increases with the flow along the aeration units. CAC could be used for process decision on variation in air supply and feed pattern to the aeration units. In a modified process to cope with sludge bulking problem, CAC could be used to estimate the air supply to the aeration unit which is merely used for reaerating the returned sludge.     

利用活性污泥制造活性炭的研究

论述了利用在活性污泥法处理废水过程中产生的好氧污泥和厌氧污泥制造活性炭的过程,选择出最佳的制作条件,并进一步测试了产品的性能。实验结果表明,利用剩余活性污泥制造活发现灰这一方法是可行的,并且在最佳条件下制成的活性炭的吸附性能比较令人满意。     

Assessing the performance of wastewater treatment with the combination of Fenton and ferrite process

Industrial wastewater typically contains various metal ions. Traditional metal ion treatment processes such as chemical precipitation generate large volumes of toxic sludge which needs to be further solidified or disposed of. The ferrite process (FP), which is another effective approach of treating metal ion-containing wastewater, can crystallize metal ions into ferrites; the sludge easily precipitates, is stable and can be recycling. This investigation explores the feasibility of the Fenton process and the FP (FFP) for treating wastewater that contains metal ions. It considers one factor that adds noise to the FP, ethylenediaminetetraacetic acid, and establishes the optimum parameters of each procedure. The analytical results demonstrate that the proper conditions for Fenton process were pH = 2, [Fe(2+)] = 10(-2) M, H(2)O(2) dosing rate = 5 x 10(-4) mol min(-1), reaction time = 12 min. For the proposed multi-stage FP, the preferred Fe(2+) dosage was 0.098 mol in each stage and the sludge met the toxicity characteristic leaching procedure standards. Following the FFP, the effluent water or the sludge easily met Taiwan's standards. Finally, the SEM test demonstrated that size of the sludge particles was 50-110 nm.     

Reduction of sludge formed during a coagulation treatment of Ridomil Gold by means of non-thermal quenched plasma pre-treatment

Chemical coagulation and adsorption, despite many drawbacks, are actually the main techniques used for the removal of pollutants from aqueous solution; however, these techniques are becoming ineffective due to the exponential increase in the amount and complexity of discharged pollutants; thus, the sludge treatment process became a more complex challenge. The present study focuses on the way to reduce the quantity of sludge formed during the removal of Ridomil Gold, a widely used pesticide-fungicide in agriculture. Results revealed that pre-treatment of initial waste solution by the gliding arc (Glidarc), a source of non-thermal plasma, leads to a significant reduction of the sludge formed during the coagulation treatment. For a 20-min pre-treated effluent Glidarc followed by chemical coagulation, there was a reduction in the volume of sludge formed in the order of 90 and 80% for alum and ferric sulfate coagulants respectively without reducing the performance of pesticide removal. Therefore, there is a positive synergism between treatment by chemical coagulation and plasma treatment. These results suggest that the Glidarc can be an effective solution for the reduction of sludge obtained during treatment by coagulation.     

Repetitive extragenic palindromic PCR (REP-PCR) as a method used for bulking process detection in activated sludge

Bulking of activated sludge is a world-widely prevalent problem and can lead to loss of bio-oxidation, further deterioration of effluent quality, and even to a complete breakdown of the entire treatment process. Most common reasons of bulking are bacterial community changes, especially excessive growth of filamentous bacteria or excess of biopolymers on surface of non-filamentous microbes. Because of complex nature of the bulking phenomenon, the successful bulking control strategy finding is still a very important need awaiting new options and advices. The repetitive extragenic palindromic PCR (REP-PCR) fingerprinting method has been applied to distinguish bacterial community in non-bulking and bulking activated sludge. The characteristic REP-PCR fingerprinting patterns, using the Ward??s clustering method, have been analyzed to determine homology/similarity relation between particular non-bulking and bulking sludge sampling. The received clustering results were in high concordance with activated sludge typing done based on physicochemical sludge analysis. The choice and application of molecular typing method in sludge analysis will depend upon the needs, skill level, and resources of the laboratory. The proposed REP-PCR method and statistical analysis of fingerprinting patterns seems to be simple, rapid, and effective methods to show differences between population in non-bulking and bulking activated sludge. It is easy to implement, and it may be useful for routinely activated sludge monitoring as well as may be helpful in early detection of bulking process.     

Toxicity Assessment of Treated Wastewater Using Cultured Human Cell Lines

Bioassay using cultured human cell lines was applied to an effluent of a wastewater treatment plant (WWTP) in Sapporo to assess their toxicity, and in order to investigate the fate of toxicity in the WWTP, bioassay of the water samples from several points in WWTP (influent, effluent, return flow from thickener, from dewatering process and from incineration process) was performed. We also applied bioassay to the mixture of the activated sludge from the investigated plant and artificial sewage. These results showed that the toxicity of the effluent was more intensive than the influent, and organic matter released from activated sludge bacteria during their decay process contributed to the increase of toxicity in the effluent.     

污水中抗生素生化去除研究进展

综述了活性污泥法、膜生物反应器、人工湿地等国内外常见抗生素生化去除方法的优缺点与适用范围,通过工艺对比发现,膜生物反应器和人工湿地能有效去除污水中的抗生素,活性污泥法对抗生素的去除率不高,且选择性较强;污泥龄和水力停留时间对抗生素的去除率有着显著影响,多数情况下反应器的运行改进也能提高抗生素的去除效果。针对抗生素污染问题,提出了采取加强型的复合式处理工艺、开展分区研究、出台相关管理政策等建议。     

A Simplified Dynamic Model for the Activated Sludge Process with High Strength Wastewaters

A simplified dynamic model for the activated sludge process with high-strength wastewaters is presented. The model is based on activated sludge models and predicts effluent chemical oxygen demand concentration using only four parameters. Experimental data for testing the model were obtained in an activated sludge plant using flax retting wastewater. The proposal of the model is described: mass balance to the system, selection of variables and behaviour of the theoretical values versus experimental results.     

Conditioning of Oily Sludge with Alum

Sludge dewatering is a process whereby water is removed from sludge so as to reduce its volume and alter its physical state from semisolid to damp solid. This physical change reduces the volume of sludge considerably and therefore the cost of disposal. The degree of reduction of sludge volume or dewatering is a function of the characteristics of sludge and the type of dewatering device. Sludge characteristics such as specific resistance, capillary suction time(CST), filter yield and solid content can be determined in the laboratories. Knowledge of these characteristics with different dosages of sludge conditioners helps in effective dewatering and sludge handling operations.Oil and grease have an affinity for suspended solids. Experiences show that the presence of oil in wastewater results in poor substrate utilization causing less aerobic treatment and subsequently hinder settling and dewatering processes. Sludge samples with different oil contents varying from 1.8% to 8.0% by weight have been examined in the laboratory to find out their specific resistance, capillary suction time and filter yield. Alum was used as a conditioner. Different dosages of alum varying from 2% to 12% by weight were used to determine the optimum chemical dosage for varying oil contents. Buchner funnel apparatus, filter leaf apparatus and capillary suction time test apparatus were used to determine the dewatering characteristics specific resistance, filter yield and capillary suction time respectively.Addition of alum decreases the specific resistances and capillary suction times of oily sludges rapidly upto 4% dosages. Alum dosages beyond 4% only increase the solids content in the sludge cake and increase the sludge volume to be handled. The total suspended solids of filtrate decrease with alum dosage. The correlations between dewatering characteristics were studied. A correlation between CST and specific resistance to filtration was established. CST can be measured easily and quickly in the laboratories. Using the CST and the correlation a quick prediction on dewaterability can be established.     

印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移转化及鉴别因子筛选

简述了印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移转化及鉴别因子筛选。以采用活性染料的印染企业为例,从常用的原辅材料、使用的生产工艺、常用的废水处理工艺等几个方面来对印染废水处理污泥危险废物鉴别过程中有毒污染物的迁移及转化进行分析。提出危险废物鉴别工作任重而道远,危险废物鉴别的关键在于日常监管。