氯、氯胺消毒下钱江源水源水消毒副产物形成特征研究

以钱江源水源水为研究对象,以氯、氯胺为消毒方式,研究了不同消毒条件下,三卤甲烷(THMs)、卤乙腈(HANs)、氯代酮(CKs)、二卤乙酸(DHAAs)、三卤乙酸(THAAs)等消毒副产物(DBPs)的形成情况,以便为水务工作者监测钱江源建库前后水质、DBPs形成的变化提供基础数据.结果显示,氯消毒下DBPs的产量比氯胺消毒高出3~7倍甚至1个数量级,但不管是氯消毒还是氯胺消毒,THMs、HAAs形成量均在我国饮用水标准范围内.氯消毒下,大部分DBPs产量为中、碱性条件酸性条件(除了CKs),氯胺消毒则呈现不同的情况(所有DBPs的产量均为p H=6、p H=7p H=8).消毒剂量对所有DBPs形成具有明显的促进作用;溴离子对THMs、DHANs、DHAAs的形成有明显的促进作用.进一步研究表明,钱江源水源水的水质比钱塘江下游九溪水源水好,DBPs形成也较低,某些指标(如有机碳、有机氮、HANs形成量等)甚至比同省水质较好的金兰水库还要好;而且由于其较高的比紫外吸收值(SUVA),DBPs的溴嵌入能力均比九溪水源水、金兰水库低.此外,就目前的钱江源水源水来说,控制消毒剂量(氯、或氯胺)是控制DBPs形成的有效策略.     

Formation of regulated and unregulated disinfection byproducts during chlorination and chloramination: Roles of dissolved organic matter type, bromide, and iodide

Algal blooms and wastewater effluents can introduce algal organic matter (AOM) and effluent organic matter (EfOM) into surface waters, respectively. In this study, the impact of bromide and iodide on the formation of halogenated disinfection byproducts (DBPs) during chlorination and chloramination from various types of dissolved organic matter (DOM, e.g., natural organic matter (NOM), AOM, and EfOM) were investigated based on the data collected from literature. In general, higher formation of trihalomethanes (THMs) and haloacetic acids (HAAs) was observed in NOM than AOM and EfOM, indicating high reactivities of phenolic moieties with both chlorine and monochloramine. The formation of haloacetaldehydes (HALs), haloacetonitriles (HANs) and haloacetamides (HAMs) was much lower than THMs and HAAs. Increasing initial bromide concentrations increased the formation of THMs, HAAs, HANs, and HAMs, but not HALs. Bromine substitution factor (BSF) values of DBPs formed in chlorination decreased as specific ultraviolet absorbance (SUVA) increased. AOM favored the formation of iodinated THMs (I-THMs) during chloramination using preformed chloramines and chlorination-chloramination processes. Increasing prechlorination time can reduce the I-THM concentrations because of the conversion of iodide to iodate, but this increased the formation of chlorinated and brominated DBPs. In an analogous way, iodine substitution factor (ISF) values of I-THMs formed in chloramination decreased as SUVA values of DOM increased. Compared to chlorination, the formation of noniodinated DBPs is low in chloramination.     

Formation potentials of typical DBPs and changes of genotoxicity for chlorinated tertiary effluent pretreated by ozone

The effects of ozonation on the formation potential of typical disinfection byproducts (DBPs) and the changes of genotoxicity during post chlorination of tertiary effluent from a sewage treatment plant were investigated. Ozonation enhanced the yields of all detected chlorine DBPs except CHCl3. At a chlorine dose of 5 mg/L, the three brominated THMs and five HAAs increased, while chloroform decreased with the increase of ozone dose from 0 to 10 mg/L (ozone dose in consumption base). At a chlorine dose of 10 mg/L, the two mixed bromochloro species THMs and two dominant HAAs (DCAA and TCAA) firstly increased and then decreased with the increase of ozone dose, with the turning point approximately occurring at an ozone dose of 5 mg/L. The genotoxicity detected using umu test, on the other hand, was removed from 7 μg 4-NQO/L to a negligible level by ozonation under an ozone dose of 5 mg/L. Chlorination could further remove the genotoxicity to some extent. It was found that SUVA (UV absorbance divided by DOC concentration) might be used as an indicative parameter for monitoring the removal of genotoxicity during the oxidation.     

Formation potentials of typical disinfection byproducts and changes of genotoxicity for chlorinated tertiary e uent pretreated by ozone

The effects of ozonation on the formation potential of typical disinfection byproducts (DBPs) and the changes of genotoxicity during post chlorination of tertiary effluent from a sewage treatment plant were investigated. Ozonation enhanced the yields of all detected chlorine DBPs except CHCl3. At a chlorine dose of 5 mg/L, the three brominated THMs and five HAAs increased, while chloroform decreased with the increase of ozone dose from 0 to 10 mg/L (ozone dose in consumption base). At a chlorine dose of 10 mg/L, the two mixed bromochloro species THMs and two dominant HAAs (DCAA and TCAA) firstly increased and then decreased with the increase of ozone dose, with the turning point approximately occurring at an ozone dose of 5 mg/L. The genotoxicity detected using umu test, on the other hand, was removed from 7 μg 4-NQO/L to a negligible level by ozonation under an ozone dose of 5 mg/L. Chlorination could further remove the genotoxicity to some extent. It was found that SUVA (UV absorbance divided by DOC concentration) might be used as an indicative parameter for monitoring the removal of genotoxicity during the oxidation.     

Effect of ferric and bromide ions on the formation and speciation of disinfection byproducts during chlorination

The e ects of ferric ion, pH, and bromide on the formation and distribution of disinfection byproducts (DBPs) during chlorination were studied. Two raw water samples from Huangpu River and Yangtze River, two typical drinking water sources of Shanghai, were used for the investigation. Compared with the samples from Huangpu River, the raw water samples from Yangtze River had lower content of total organic carbon (TOC) and ferric ions, but higher bromide concentrations. Under controlled chlorination conditions, four trihalomethanes (THMs), nine haloacetic acids (HAAs), total organic halogen (TOX) and its halogen species fractions, including total organic chlorine (TOCl) and total organic bromide (TOBr), were determined. The results showed that co-existent ferric and bromide ions significantly promoted the formation of total THMs and HAAs for both raw water samples. Higher concentration of bromide ions significantly changed the speciation of the formed THMs and HAAs. There was an obvious shift to brominated species, which might result in a more adverse influence on the safety of drinking water. The results also indicated that high levels of bromide ions in raw water samples produced higher percentages of unknown TOBr.     

Formation and control of disinfection byproducts and toxicity during reclaimed water chlorination: A review

Chlorination is essential to the safety of reclaimed water; however, this process leads to concern regarding the formation of disinfection byproducts (DBPs) and toxicity. This study reviewed the formation and control strategies for DBPs and toxicity in reclaimed water during chlorination. Both regulated and emerging DBPs have been frequently detected in reclaimed water during chlorination at a higher level than those in drinking water, indicating they pose a greater risk to humans. Luminescent bacteria and Daphnia magna acute toxicity, anti-estrogenic activity and cytotoxicity generally increased after chlorination because of the formation of DBPs. Genotoxicity by umu-test and estrogenic activity were decreased after chlorination because of destruction of toxic chemicals. During chlorination, water quality significantly impacted changes in toxicity. Ammonium tended to attenuate toxicity changes by reacting with chlorine to form chloramine, while bromide tended to aggravate toxicity changes by forming hypobromous acid. During pretreatment by ozonation and coagulation, disinfection byproduct formation potential (DBPFP) and toxicity formation potential (TFP) occasionally increase, which is accompanied by DOC removal; thus, the decrease of DOC was limited to indicate the decrease of DBPFP and TFP. It is more important to eliminate the key fraction of precursors such as hydrophobic acid and hydrophilic neutrals. During chlorination, toxicities can increase with the increasing chlorine dose and contact time. To control the excessive toxicity formation, a relatively low chlorine dose and short contact time were required. Quenching chlorine residual with reductive reagents also effectively abated the formation of toxic compounds.     

配水管网中生物稳定性和消毒副产物的变化及相关性

研究了上海市2条不同水源水厂配水管网中可同化有机碳（AOC）、三卤甲烷（THMs）和卤乙酸（HAAs）的变化情况,并对饮用水生物稳定性和消毒副产物间的相关性进行了分析.结果表明,管网中AOC和HAAs含量受余氯和微生物活动双重作用的影响,在距水厂较近、余氯较高的管网中,可能因氯与有机物继续反应出现上升,在余氯较低的管网末梢则因为微生物降解作用使含量下降;THMs含量则只受余氯的影响,随管网延伸持续增长.HAAs与AOC含量间存在较好的线形关系,前体物间具有相似性,THMs与AOC含量间呈正相关性;作为饮用水安全性的2个重要方面,生物稳定性和消毒副产物间具有内在的关联性.     

饮用水含氮与含碳消毒副产物的生成潜能及其毒性

消毒副产物生成潜能测试常用于表征水中消毒副产物的前体物含量.不同于三氯甲烷等含碳消毒副产物,二卤代乙腈（DHANs）与二卤代乙酰胺（DHAcAms）等含氮消毒副产物在氯消毒的余氯存在下易分解,并且在氯胺消毒过程中可由氯胺提供氮源生成,因此常用于含碳消毒副产物的生成潜能测试方法（如Krasner提出的测试法）可能无法有效揭示DHANs与DHAcAms的前体物水平.本研究以三氯甲烷和氯醛两种含碳消毒副产物为对比,考察DHANs与DHAcAms在饮用水氯消毒与氯胺消毒过程中不同投氯量与反应时间下的生成量,识别最大生成量对应的消毒条件,以便更好地评估水样中DHANs与DHAcAms的前体物浓度.同时,对消毒过程中生成的这些挥发性消毒副产物进行毒性评价.结果显示,两个水样氯消毒的DHANs与DHAcAms生成量分别为6.19~40.08、1.34~15.75 nmol·mg^-1（mg^-1以TOC计）;氯胺消毒的DHANs与DHAcAms生成量分别为2.63~21.46、18.43~49.99 nmol·mg^-1.Krasner测试法条件下的DHANs与DHAcAms生成量均最低.在投氯量为TOC+8×NH₃-N、反应时间为24 h的氯消毒条件下,氯胺投加量20×TOC、反应时间为3 d的氯胺消毒条件下,两个水样具有最高水平的DHANs与DHAcAms生成量,并且消毒副产物毒性也高于Krasner法测试条件下的毒性水平.因此,氯消毒采用投氯量TOC+8×NH₃-N、反应时间24 h,氯胺消毒采用投加量20×TOC、反应时间3 d的生成潜能测试条件可能更好地揭示水中DHANs和DHAcAms的前体物浓度水平.     

Formation potential and analysis of 32 regulated and unregulated disinfection by-products: Two new simplified methods

Water disinfection is an essential process that provides safe water by inactivating pathogens that cause waterborne diseases. However, disinfectants react with organic matter naturally present in water, leading to the formation of disinfection by-products (DBPs). Multi-analyte methods based on mass spectrometry (MS) are preferred to quantify multiple DBP classes at once however, most require extensive sample pre-treatment and significant resources. In this study, two analytical methods were developed for the quantification of 32 regulated and unregulated DBPs. A purge and trap (P&T) coupled with gas chromatography mass spectrometry (GC-MS) method was optimized that automated sample pre-treatment and analyzed volatile and semi-volatile compounds, including trihalomethanes (THMs), iodinated trihalomethanes (I-THMs), haloacetonitriles (HANs), haloketones (HKTs) and halonitromethanes (HNMs). LOQs were between 0.02-0.4 µg/L for most DBPs except for 8 analytes that were in the low µg/L range. A second method with liquid chromatography (LC) tandem mass spectrometry (MS/MS) was developed for the quantification of 10 haloacetic acids (HAAs) with a simple clean-up and direct injection. The LC-MS/MS direct injection method has the lowest detection limits reported (0.2-0.5 µg/L). Both methods have a simple sample pre-treatment, which make it possible for routine analysis. Hyperchlorination and uniform formation conditions (UFC) formation potential tests with chlorine were evaluated with water samples containing high and low TOC. Hyperchlorination formation potential test maximized THMs and HAAs while UFC maximized HANs. Ascorbic acid was found to be an appropriate quencher for both analytical methods. Disinfected drinking water from four water utilities in Alberta, Canada were also evaluated.     

氯消毒过程中水中色氨酸产生THMs和HAAs的特征研究

以氨基酸为代表的溶解性含氮有机物在水源水中广泛存在,成为制水工艺消毒副产物的主要前体物之一.选取色氨酸（Trp）为含氮前体物模型,考察了其在消毒工艺中产生受控消毒副产物的途径及影响因素.结果表明,Trp氯化过程经取代,脱羧,水解等一系列反应,可生成卤乙酸（HAAs）,三卤甲烷（THMs）等消毒副产物.THMs和HAAs的生成量随加氯量增加;随接触时间的延长逐渐增加.温度的升高,HAAs的生成量先增大后减少;碱性条件有利于THMs和HAAs的生成.氯胺消毒和遮光条件下可明显减少THMs和HAAs的产生.     

膜生物反应器处理城市污水的后续次氯酸钠消毒研究

针对膜生物反应器（membrane bioreactor,MBR）处理城市污水的后续次氯酸钠消毒,分别开展了不同氯的投加剂量对指示微生物（总大肠菌群和粪大肠菌群）的灭活效果、消毒副产物（disinfection by-products,DBPs）生成量以及消毒后出水发光菌急性毒性研究.结果表明,在工程应用中MBR处理工...     

组合氯化消毒工艺的卤代消毒副产物生成特性

比较4种单独使用氯或组合氯化消毒工艺在较长管网停留时的卤代消毒副产物生成情况.4种工艺为单独游离氯消毒、氯胺消毒、清水池游离氯消毒后转氯胺的先氯后氨消毒、短时游离氯后转氯胺的顺序氯化消毒工艺.结果表明,游离氯消毒工艺在管网停留时间长时,卤代消毒副产物会持续大量的生成,而一氯胺消毒工艺生成的卤代消毒副产物量很低.目前使用较为普遍的先氯后氨消毒工艺与游离氯消毒相比,可以降低卤代消毒副产物的生成量,管网停留24 h时,三卤甲烷的生成量降低了9.6%,卤乙酸的生成量减低了42%.但是先氯后氨消毒工艺由于游离氯接触时间约为2 h,卤代消毒副产物已经大量生成.短时游离氯后转氯胺的顺序氯化消毒工艺,由于控制了游离氯的接触时间,可以在保障消毒工艺灭活微生物效果的同时更为有效地控制卤代消毒副产物,管网停留24 h时,三卤甲烷的生成量与单独游离氯消毒工艺相比降低了48%,卤乙酸的生成量减低了72%.因此,顺序氯化消毒工艺可以更好地控制卤代消毒副产物的生成,提高水质安全性.     

How well does XAD resin extraction recover halogenated disinfection byproducts for comprehensive identification and toxicity testing?

Halogenated disinfection byproducts (DBPs) are an unintended consequence of drinking water disinfection, and can have significant toxicity. XAD resins are commonly used to extract and enrich trace levels of DBPs for comprehensive, nontarget identification of DBPs and also for in vitro toxicity studies. However, XAD resin recoveries for complete classes of halogenated DBPs have not been evaluated, particularly for low, environmentally relevant levels (ng/L to low µg/L). Thus, it is not known whether levels of DBPs or the toxicity of drinking water might be underestimated. In this study, DAX-8/XAD-2 layered resins were evaluated, considering both adsorption and elution from the resins, for extracting 66 DBPs from water. Results demonstrate that among the 7 classes of DBPs investigated, trihalomethanes (THMs), including iodo-THMs, were the most efficiently adsorbed, with recovery of most THMs ranging from 50%-96%, followed by halonitromethanes (40%-90%). The adsorption ability of XAD resins for haloacetonitriles, haloacetamides, and haloacetaldehydes was highly dependent on the individual species. The adsorption capacity of XAD resins for haloacetic acids was lower (5%-48%), even after adjusting to pH 1 before extraction. Recovery efficiency for most DBPs was comparable with their adsorption, as most were eluted effectively from XAD resins by ethyl acetate. DBP polarity and molecular weight were the two most important factors that determine their recovery. Recovery of trichloromethane, iodoacetic acid, chloro- and iodo-acetonitrile, and chloroacetamide were among the lowest, which could lead to underestimation of toxicity, particularly for iodoacetic acid and iodo-acetonitrile, which are highly toxic.     

One representative water supply system in China with nitrosamine concern: Challenges and treatment strategies

Four sampling campaigns were conducted in two years to understand the fluctuation of N-Nitrosamines (NAs) and their precursors in one drinking water treatment plant (DWTP) in East China in different seasons. This water supply system has been facing several nitrosamine challenges related with source water, including the switch of water source, high concentration of ammonium, formed NAs and NA formation potential (FP) in source water. Besides, the use of ozonation in the DWTP and chloramination in networks will increase the NDMA concentration in tap water. To address these challenges, the bio-pretreatment was applied in this DWTP to decrease the concentration of ammonium and NAs. The following biological activated carbon (BAC) will neutralize the nitrosamine increase brought by ozonation. The use of free chlorine in disinfection process will also decrease the NDMA formation compared with chloramination. The results will benefit other cities in China and other countries with similar impacted water sources.     

Formation potentials of typical disinfection byproducts and changes of genotoxicity for chlorinated tertiary effluent pretreated by ozone

The effects of ozonation on the formation potential of typical disinfection byproducts (DBPs) and the changes of genotoxicity during post chlorination of tertiary effluent from a sewage treatment plant were investigated. Ozonation enhanced the yields of all detected chlorine DBPs except CHCl3. At a chlorine dose of 5 mg/L, the three brominated THMs and five HAAs increased, while chloroform decreased with the increase of ozone dose from 0 to 10 mg/L (ozone dose in consumption base). At a chlorine dose of 10 ...     

南水北调丹江口水库水氯(胺)化消毒副产物产生特性与消毒工艺对比

系统研究了南水北调中线工程水源——丹江口水库水在氯(胺)化消毒条件下,常规消毒副产物的产生特性,考察了消毒方式、消毒剂投加量、接触时间、p H和溴离子浓度等因素的影响,并对消毒工艺参数进行了优化.结果发现,丹江口水库水经氯化消毒可产生三氯甲烷、二氯一溴甲烷等常规含碳和较低浓度二氯乙腈、三氯硝基甲烷等含氮消毒副产物,而氯胺化消毒仅产生三氯甲烷和三氯硝基甲烷等消毒副产物(disinfection by-products,DBPs).自由氯消毒过程产生的各类型DBPs浓度约为氯胺消毒的7.5倍,短时自由氯转氯胺方式DBPs产生量介于两者之间;随着自由氯投加量增加,各类型消毒副产物均呈现增加趋势,投加量大于2 mg·L-1后DBPs增加量较少.随氯胺投加量增加,三氯甲烷生成量变化不大,投加量大于2mg·L-1后可产生三氯硝基甲烷等副产物.随反应时间延长,自由氯的衰减速率明显大于氯胺,同时消毒副产物增长量明显快于氯胺消毒.随着p H升高,自由氯消毒后三卤甲烷含量呈现增加趋势,而氯胺消毒后变化不明显.随溴离子浓度的增加,自由氯和氯胺消毒后副产物类型均向溴代DBPs转变,同时总生成量明显增加,自由氯消毒DBPs增长量明显大于氯胺消毒过程.丹江口水库水采用氯胺化消毒可以降低消毒副产物的生成风险,如采用自由氯消毒方式,水厂需根据实际常规处理工艺重点控制自由氯的投加量等参数.     

饮用水消毒副产物分析及相关研究进展

饮用水消毒副产物（DBPs）是消毒剂和一些天然有机物（NOM）反应生成的化合物,主要包括三卤甲烷（THMs）、卤代G@（HAAs）、卤代乙腈（HANs）和致诱变化舍物（MX）4类。本文针对氯、氯胺、二氧化氯、臭氧4种主要消毒方式产生的消毒副产物,讨论了有关分析技术的发展过程,从DBPs的前处理技术、分析技术等角度,介绍了DBPs研究领域近期所取得的进展,并展望了今后研究的发展方向。     

两点短时游离氯后转氯胺的顺序氯化消毒工艺研究

基于顺序氯化消毒工艺的原理,采用两点短时游离氯后转氯胺的两点顺序氯化消毒工艺,即在过滤和清水池前的两点分别加氯,并在清水池加氯后立即加氨转化为氯胺消毒的工艺,该工艺在常规处理工艺的给水厂进行了消毒试验.结果表明,加氯点的适当提前,不仅有利于控制消毒副产物的生成量,而且有效抑制了滤池中的生物膜滋生.两点顺序氯化消毒工艺中生成的卤代消毒副产物比相同条件下一次性加入等量的氯消毒剂的消毒方法产生的三卤甲烷(THMs)平均减少了51.6％,卤乙酸(HAAs)平均减少了46.7％.细菌学指标HPC的结果也显示出了该工艺在保障水质的微生物安全方面的优势.     

Impact of combining chlorine dioxide and chlorine on DBP formation in simulated indoor swimming pools

The main objective of this study was to assess the combined use of chlorine dioxide (ClO2) and chlorine (Cl2) on the speciation and kinetics of disinfection by-product (DBP) formation in swimming pools using synthetic pool waters prepared with a body fluid analog (BFA) and/or fresh natural water. At 1:25 (mass ratio) of ClO2 to Cl2, there was no significant reduction in the formation of trihalomethanes (THMs) and haloacetic acids (HAAs) for both BFA solution and natural water compared to the application of Cl2 alone. When the mass ratio of ClO2 to Cl2 increased to 1:1, substantial decreases in both THMs and HAAs were observed in the natural water, while there was almost no change of DBP formations in the BFA solution. Haloacetonitriles and halonitromethanes levels in both water matrices remained similar. In the presence of bromide, the overall DBP formation increased in both BFA solution and natural water. For the DBP formation kinetics, after 72 hr of contact time, very low formation of THMs and HAAs was observed for the use of ClO2 only. Compared to Cl2 control, however, applying the 1:1 mixture of ClO2/Cl2 reduced THMs by > 60% and HAAs by > 50%. Chlorite was maintained below 1.0 mg/L, while the formation of chlorate significantly increased over the reaction time. Finally, in a bench-scale indoor pool experiment, applying ClO2 and Cl2 simultaneously produced less THMs compared to Cl2 control and kept chlorite at < 0.4 mg/L, while HAAs and chlorate accumulated over 4-week operation period.     

太湖、钱塘江取水口底泥及周边土壤有机物形成消毒副产物的特征研究

底泥、土壤均是水体有机物的重要来源,但目前相关消毒副产物(DBPs)形成方面的研究偏少.本研究以长三角重要水源地太湖、钱塘江取水口的底泥和周边土壤的浸出液为研究对象,探索氯、臭氧+氯、氯胺、臭氧+氯胺4种消毒方式下,三卤甲烷(THMs)、卤代酮(HKs)、卤乙腈(HANs)、卤代硝基甲烷(HNMs)的形成情况.结果表明,太湖、钱塘江取水口的底泥、周边土壤有机物的芳香度均很低(SUVA254(即比紫外吸光值)2),与腐殖质(Sigma)相比,底泥、土壤有机物不是氯消毒中THMs的重要前驱物,但却是HANs特别是HNMs的重要前驱物.相比氯消毒,氯胺消毒能大幅降低土壤、底泥有机物THMs、HKs、HANs、HNMs的生成量,而且也可抑制含溴DBPs的形成.臭氧预处理大幅提高了氯、氯胺消毒中HKs、HNMs的产量,但对THMs、HANs则不一定.太湖、钱塘江的土壤、底泥存在一定的溴污染,但不管是哪种消毒方式,均是HNMs的溴嵌入因子最大.