Comparing dark- and photo-Fenton-like degradation of emerging pollutant over photo-switchable Bi2WO6/CuFe2O4: Investigation on dominant reactive oxidation species

The extensive use of tetracycline hydrochloride (TCH) poses a threat to human health and the aquatic environment. Here, magnetic p-n Bi₂WO₆/CuFe₂O₄ catalyst was fabricated to efficiently remove TCH. The obtained Bi₂WO₆/CuFe₂O₄ exhibited 92.1% TCH degradation efficiency and 50.7% and 35.1% mineralization performance for TCH and raw secondary effluent from a wastewater treatment plant in a photo-Fenton-like system, respectively. The remarkable performance was attributed to the fact that photogenerated electrons accelerated the Fe(III)/Fe(II) and Cu(II)/Cu(I) conversion for the Fenton-like reaction between Fe(II)/Cu(I) and H₂O₂, thereby generating abundant ?OH for pollutant oxidation. Various environmental factors including H₂O₂ concentration, initial pH, catalyst dosage, TCH concentration and inorganic ions were explored. The reactive oxidation species (ROS) quenching results and electron spin resonance (ESR) spectra confirmed that ?O₂^? and ?OH were responsible for the dark and photo-Fenton-like systems, respectively. The degradation mechanisms and pathways of TCH were proposed, and the toxicity of products was evaluated. This work contributes a highly efficient and environmentally friendly catalyst and provides a clear mechanistic explanation for the removal of antibiotic pollutants in environmental remediation.     

Effect of reduction pretreatments on PdAg/Al2O3 for HCHO and CO oxidation

PdAg/Al₂O₃ were pretreated by CO and H₂ reduction pretreatments, respectively. The reduced catalysts were tested for HCHO and CO oxidation and characterized by Brunner Emmet Teller (BET), X-ray diffraction (XRD), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS) and oxygen temperature programmed desorption (O₂-TPD). These results indicate that the pretreatments have effect on PdAg reconstruction, PdAg particle size and active oxygen species, which are responsible for the catalytic performance. Compared with H₂ reduction method, CO reduction is more suitable for PdAg/Al₂O₃ pretreatment. PdAg/Al₂O₃-CO exhibited better catalytic performance.     

Role of NO and SO2 in mercury oxidation over a La2O3/Fe2O3 catalyst with high thermal stability

In this study, the thermal stability of a ferric oxide catalyst for mercury oxidation was found to be considerably promoted by doping with La₂O₃. The catalysts doped with La₂O₃ maintained a higher surface area when subjected to high-temperature calcination, with lower average pore size and a narrower pore size distribution. X-ray diffraction (XRD) results revealed that La₂O₃ doping hinders the growth of catalyst particles and crystallization of the material at high temperatures. Both NO and SO₂ inhibited Hg⁰ oxidation over the La₂O₃/Fe₂O₃ catalyst. Fourier transform infrared (FTIR) spectra revealed that SO₂ reacts with O₂ over the catalysts to form several species that are inert for mercury oxidation, such as SO₄^2?, HSO₄^?, or other related species; these inert species cover the catalyst surface and consequently decrease Hg⁰ oxidation capacity. In addition, NO or SO₂ competed with Hg⁰ for active sites on the La₂O₃/Fe₂O₃ catalyst and hindered the adsorption of mercury, thereby inhibiting subsequent Hg⁰ oxidation. Hg⁰ oxidation on the La₂O₃/Fe₂O₃ catalyst mainly followed the Eley–Rideal mechanism. Moreover, the inhibition effects of NO and SO₂ were at least partially reversible, and the catalytic activity was temporarily restored after eliminating NO or SO₂.     

Ce-based catalysts used in advanced oxidation processes for organic wastewater treatment: A review

Refractory organic pollutants in water threaten human health and environmental safety,and advanced oxidation processes (AOPs) are effective for the degradation of these pollutants.Catalysts play vital role in AOPs,and Ce-based catalysts have exhibited excellent performance.Recently,the development and application of Ce-based catalysts in various AOPs have been reported.Our study conducts the first review in this rapid growing field.This paper clarifies the variety and properties of Ce-based cata...     

Comparison of UV-based advanced oxidation processes for the removal of different fractions of NOM from drinking water

This study examined the effectiveness for degradation of hydrophobic (HPO), transphilic (TPI) and hydrophilic (HPI) fractions of natural organic matter (NOM) during UV/H₂O₂, UV/TiO₂ and UV/K₂S₂O₈ (UV/PS) advanced oxidation processes (AOPs). The changing characteristics of NOM were evaluated by dissolved organic carbon (DOC), the specific UV absorbance (SUVA), trihalomethanes formation potential (THMFP), organic halogen adsorbable on activated carbon formation potential (AOXFP) and parallel factor analysis of excitation–emission matrices (PARAFAC-EEMs). In the three UV-based AOPs, HPI fraction with low molecular weight and aromaticity was more likely to degradate than HPO and TPI, and the removal efficiency of SUVA for HPO was much higher than TPI and HPI fraction. In terms of the specific THMFP of HPO, TPI and HPI, a reduction was achieved in the UV/H₂O₂ process, and the higest removal rate even reached to 83%. UV/TiO₂ and UV/PS processes can only decrease the specific THMFP of HPI. The specific AOXFP of HPO, TPI and HPI fractions were all able to be degraded by the three UV-based AOPs, and HPO content is more susceptible to decompose than TPI and HPI content. UV/H₂O₂ was found to be the most effective treatment for the removal of THMFP and AOXFP under given conditions. C1 (microbial or marine derived humic-like substances), C2 (terrestrially derived humic-like substances) and C3 (tryptophan-like proteins) fluorescent components of HPO fraction were fairly labile across the UV-based AOPs treatment. C3 of each fraction of NOM was the most resistant to degrade upon the UV-based AOPs. Results from this study may provide the prediction about the consequence of UV-based AOPs for the degradation of different fractions of NOM with varied characteristics.     

Green and efficient degradation of cefoperazone sodium by Bi4O5Br2 leading to the production of non-toxic products: Performance and degradation pathway

Photocatalytic process represents a promising approach to overcome the pollution challenge associated with the antibiotics-containing wastewater. This study provides a green, efficient and novel approach to remove cephalosporins, particularly cefoperazone sodium (CFP). Bi₄O₅Br₂ was chosen for the first time to systematically study its degradation for CFP, including the analysis of material structure, degradation performance, the structure and toxicity of the transformation products, etc. The degradation rate results indicated that Bi₄O₅Br₂ had an excellent catalytic activity leading to 78% CFP removal compared with the pure BiOBr (38%) within 120 min of visible light irradiation. In addition, the Bi₄O₅Br₂ presents high stability and good organic carbon removal efficiency. The effects of the solution pH (3.12 - 8.75) on catalytic activity revealed that CFP was mainly photocatalyzed under acidic conditions and hydrolyzed under alkaline conditions. Combined with active species and degradation product identification, the photocatalytic degradation pathways of CFP by Bi₄O₅Br₂ was proposed, including hydrolysis, oxidation, reduction and decarboxylation. Most importantly, the identified products were all hydrolysis rather than oxidation byproducts transformed from the intermediate of β-lactam bond cleavage in CFP molecule, quite different from the mostly previous studies. Furthermore, the final products were demonstrated to be less toxic through the toxicity analysis. Overall, this study illustrates the detailed mechanism of CFP degradation by Bi₄O₅Br₂ and confirms Bi₄O₅Br₂ to be a promising material for the photodegradation of CFP.     

Removal of elemental mercury by photocatalytic oxidation over La2O3/Bi2O3 composite

La₂O₃/Bi₂O₃ photocatalysts were prepared by impregnation of Bi₂O₃ with an aqueous solution of lanthanum precursor followed by calcination at different temperatures. The composite materials were used for the first time for the photocatalytic removal of Hg⁰ from a simulated flue gas under UV light irradiation. The results showed that the sample containing 6 wt.% La₂O₃ and calcined at 500°C has the highest dispersion of the active sites, which was promoted by the strong interaction with the support (i.e., the formation of Bi-O-La species). Since they are fully accessible on the surface, the material also exhibits excellent optical properties while the heterojunction formed in La₂O₃/Bi₂O₃ promotes the separation and migration of photoelectron-hole pairs and thus Hg⁰ oxidation efficiency is enhanced. The effects of the various factors (e.g., the reaction temperature and composition of the simulated flue gas (i.e., O₂, NO, H₂O, and SO₂)) on the efficiency of the Hg⁰ photocatalytic oxidation were investigated. The results demonstrated that O₂ and SO₂ enhanced the efficiency of the reaction while the reaction temperature, NO, and H₂O had an inhibitory effect.     

Dielectric barrier discharge plasma-assisted modification of g-C3N4/Ag2O/TiO2-NRs composite enhanced photoelectrocatalytic activity

Dielectric barrier discharge (DBD) plasma applied as surface treatment technology was employed for the modification of Ag₂O and graphitic carbon nitride (g-C₃N₄) powders. Subsequently, the pretreated powders were sequentially loaded onto TiO₂ nanorods (TiO₂-NRs) via electro-deposition, followed by calcination at N₂ atmosphere. The results indicated that at the optimal plasma discharge time of 5 min for modification of g-C₃N₄ and Ag₂O, photocurrent density of ternary composite was 6 times to bare TiO₂-NRs under UV-visible light irradiation. Phenol was degraded by using DBD plasma-modified g-C₃N₄/Ag₂O/TiO₂-NRs electrode to analyze the photoelectrocatalytic performance. The removal rate of phenol for g-C₃N₄-5/Ag₂O-5/TiO₂-NRs electrode was about 3.07 times to that for TiO₂-NRs electrode. During active species scavengers’ analysis, superoxide radicals and hydroxyl radicals were the main oxidation active species for pollutants degradation. A possible electron-hole separation and transfer mechanism of ternary composite with high photoelectrocatalytic performance was proposed.     

Efficient photocatalysis of tetracycline hydrochloride (TC-HCl) from pharmaceutical wastewater using AgCl/ZnO/g-C3N4 composite under visible light: Process and mechanisms

AgCl/ZnO/g-C₃N₄, a visible light activated ternary composite catalyst, was prepared by combining calcination, hydrothermal reaction and in-situ deposition processes to treat/photocatalyse tetracycline hydrochloride (TC-HCl) from pharmaceutical wastewater under visible light. The morphological, structural, electrical, and optical features of the novel photocatalyst were characterized using scanning electron microscopy (SEM), UV-visible light absorption spectrum (UV–Vis DRS), X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), and transient photocurrent techniques. All analyses confirmed that the formation of heterojunctions between AgCl/ZnO and g-C₃N₄ significantly increase electron-hole transfer and separation compared to pure ZnO and g-C₃N₄. Thus, AgCl/ZnO/g-C₃N₄ could exhibit superior photocatalytic activity during TC-HCl assays (over 90% removal) under visible light irradiation. The composite could maintain its photocatalytic stability even after four consecutive reaction cycles. Hydrogen peroxide (H₂O₂) and superoxide radical (^·O₂) contributed more than holes (h⁺) and hydroxyl radicals (^·OH) to the degradation process as showed by trapping experiments. Liquid chromatograph-mass spectrometer (LC-MS) was used for the representation of the TC-HCl potential degradation pathway. The applicability and the treatment potential of AgCl/ZnO/g-C₃N₄ against actual pharmaceutical wastewater showed that the composite can achieve removal efficiencies of 81.7%, 71.4% and 69.0% for TC-HCl, chemical oxygen demand (COD) and total organic carbon (TOC) respectively. AgCl/ZnO/g-C₃N₄ can be a prospective key photocatalyst in the field of degradation of persistent, hardly-degradable pollutants, from industrial wastewater and not only.     

Fabricating Fe3O4-schwertmannite as a Z-scheme photocatalyst with excellent photocatalysis-Fenton reaction and recyclability

Here we reported an effective method to solve the rate-limiting steps, such as the reduction of Fe³⁺ to Fe²⁺ and an invalid decomposition of H₂O₂ in a conventional Fenton-like reaction. A magnetic heterogeneous photocatalyst, Fe₃O₄-schwertmannite(Fe₃O₄-sch) was successfully developed by adding Fe₃O₄ in the formation process of schwertmannite. Fe₃O₄-sch shows excelle...     

Efficient degradation of Rhodamine B by magnetically recoverable Fe3O4-modified ternary CoFeCu-layered double hydroxides via activating peroxymonosulfate

Environment-friendly nano-catalysts capable of activating peroxymonosulfate (PMS) have received increasing attention recently. Nevertheless, traditional nano-catalysts are generally well dispersed and difficult to be separated from reaction system, so it is particularly important to develop nano-catalysts with both good catalytic activity and excellent recycling efficiency. In this work, magnetically recoverable Fe₃O₄-modified ternary CoFeCu-layered double hydroxides (Fe₃O₄/CoFeCu-LDHs) was prepared by a simple co-precipitation method and initially applied to activate PMS for the degradation of Rhodamine B (RhB). X-ray diffraction (XRD), fourier transform infrared spectrometer (FT-IR), scanning electron microscope (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller method (BET), and vibrating sample magnetometer (VSM) were applied to characterize morphology, structure, specific surface area and magnetism. In addition, the effects of several key parameters were evaluated. The Fe₃O₄/CoFeCu-LDHs exhibited high catalytic activity, and RhB degradation efficiency could reach 100% within 20 min by adding 0.2 g/L of catalyst and 1 mmol/L of PMS into 50 mg/L of RhB solution under a wide pH condition (3.0-7.0). Notably, the Fe₃O₄/CoFeCu-LDHs showed good super-paramagnetism and excellent stability, which could be effectively and quickly recovered under magnetic condition, and the degradation efficiency after ten cycles could still maintain 98.95%. Both radicals quenching tests and electron spin resonance (ESR) identified both HO? and SO₄^?? were involved and SO₄^?? played a dominant role on the RhB degradation. Finally, the chemical states of the sample's surface elements were measured by X-ray photoelectron spectroscopy (XPS), and the possible activation mechanism in Fe₃O₄/CoFeCu-LDHs/PMS system was proposed according to comprehensive analysis.     

Catalytic oxidation effect of MnSO4 on As(III) by air in alkaline solution

The catalytic oxidation effect of MnSO₄ on As(III) by air in an alkaline solution was investigated. According to the X-ray diffraction (XRD), scanning electron microscope-energy dispersive spectrometer (SEM-EDS) and X-ray photoelectron spectroscopy (XPS) analysis results of the product, it was shown that the introduction of MnSO₄ in the form of solution would generate Na_0.55Mn₂O₄·1.5H₂O with strong catalytic oxidation ability in the aerobic alkaline solution, whereas the catalytic effect of the other product MnOOH is not satisfactory. Under the optimal reaction conditions of temperature 90°C, As/Mn molar ratio 12.74:1, air flow rate 1.0 L/min, and stirring speed 300 r/min, As(III) can be completely oxidized after 2 hr reaction. The excellent catalytic oxidation ability of MnSO₄ on As(III) was mainly attributed to the indirect oxidation of As(III) by the product Na_0.55Mn₂O₄·1.5H₂O. This study shows a convenient and efficient process for the oxidation of As(III) in alkali solutions, which has potential application value for the pre-oxidation of arsenic-containing solution or the detoxification of As(III).     

Degradation of duloxetine: Identification of transformation products by UHPLC-ESI(+)-HRMS/MS, in silico toxicity and wastewater analysis

Duloxetine (DUL), an antidepressant drug, has been detected in surface water and wastewater effluents, however, there is little information on the formation of its transformation products (TPs). In this work, hydrolysis, photodegradation (UV irradiation) and chlorination experiments were performed on spiked distillated water, under controlled experimental conditions to simulate abiotic processes that can occur in the environment and wastewater treatment plants (WWTPs). Eleven TPs, nine from reaction with UV light and two from chlorine contact, were formed and detected by ultra-high performance liquid chromatography coupled to quadrupole time-of-flight mass spectrometry, and nine of them had their chemical structures elucidated upon analyses of their fragmentation patterns in MS/MS spectra. The formation and degradation of the TPs were observed. The parent compound was completely degraded after 30?min in photodegradation and after 24?hr in chlorination. Almost all TPs were completely degraded in the experiments. The ecotoxicity and mutagenicity of the TPs were predicted based on several in silico models and it was found that a few of these products presented more ecotoxicity than DUL itself and six TPs showed positive mutagenicity. Finally, wastewater samples were analyzed and DUL and one TP, possibly formed by chlorination process, were detected in the effluent, which showed that WWTP not only did not remove DUL, but also formed a TP.     

Identification of close relationship between atmospheric oxidation and ozone formation regimes in a photochemically active region

Understanding ozone (O₃) formation regime is a prerequisite in formulating an effective O₃ pollution control strategy. Photochemical indicator is a simple and direct method in identifying O₃ formation regimes. Most used indicators are derived from observations, whereas the role of atmospheric oxidation is not in consideration, which is the core driver of O₃ formation. Thus, it may impact accuracy in signaling O₃ formation regimes. In this study, an advanced three-dimensional numerical modeling system was used to investigate the relationship between atmospheric oxidation and O₃ formation regimes during a long-lasting O₃ exceedance event in September 2017 over the Pearl River Delta (PRD) of China. We discovered a clear relationship between atmospheric oxidative capacity and O₃ formation regime. Over eastern PRD, O₃ formation was mainly in a NO_x-limited regime when HO₂/OH ratio was higher than 11, while in a VOC-limited regime when the ratio was lower than 9.5. Over central and western PRD, an HO₂/OH ratio higher than 5 and lower than 2 was indicative of NO_x-limited and VOC-limited regime, respectively. Physical contribution, including horizontal transport and vertical transport, may pose uncertainties on the indication of O₃ formation regime by HO₂/OH ratio. In comparison with other commonly used photochemical indicators, HO₂/OH ratio had the best performance in differentiating O₃ formation regimes. This study highlighted the necessities in using an atmospheric oxidative capacity-based indicator to infer O₃ formation regime, and underscored the importance of characterizing behaviors of radicals to gain insight in atmospheric processes leading to O₃ pollution over a photochemically active region.     

Effect of different reduction methods on Pd/Al2O3 for o-xylene oxidation at low temperature

Pd/Al₂O₃ was pretreated by CO, H₂ and NaBH₄ reduction, respectively. The reduced catalysts were tested for o-xylene oxidation and characterized by power X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and temperature-programmed decomposition of palladium hydride (TPDH). The characterizations indicate the pretreatments lead to distinct Pd particle sizes and amount of surface activated oxygen species, which are responsible for the catalytic performance. Compared with H₂ and NaBH₄ reduction methods, CO reduction shows a strong interaction between Pd and Al₂O₃ with smaller Pd particle size and more surface activated oxygen. It exhibited excellent catalytic performance, complete oxidation of 50 ppmV o-xylene at 85°C with a WHSV of 60,000 mL/(g∙hr).     

Construction of Ag2CO3/BiOBr/CdS ternary composite photocatalyst with improved visible-light photocatalytic activity on tetracycline molecule degradation

Photocatalytic degradation was considered as a best strategy for the removal of antibiotic drug pollutants from wastewater. The photocatalyst of ABC (Ag₂CO₃/BiOBr/CdS) composite synthesized by hydrothermal and precipitation method. The ABC composite used to investigate the degradation activity of tetracycline (TC) under visible light irradiation. The physicochemical characterization methods (e.g. scanning electron microscopy (SEM), transmission electron microscopy (TEM), high resolution-transmission electron microscopy (HR-TEM), ultraviolet visible spectroscopy (UV), photoluminescence (PL) and time resolved photoluminescence (TRPL) clearly indicate that the composite has been construct successfully that enhances the widened visible light absorption, induces charge transfer and separation efficiency of electron – hole pairs. The photocatalytic activity of all samples was examined through photodegradation of tetracycline in aqueous medium. The photocatalytic degradation rate of ABC catalyst could eliminate 98.79% of TC in 70 min, which is about 1.5 times that of Ag₂CO_3, 1.28 times that of BiOBr and 1.1 times that of BC catalyst, respectively. The role of operation parameters like, TC concentration, catalyst dosage and initial pH on TC degradation activity were studied. Quenching experiment was demonstrated that ·OH and O₂^·− were played a key role during the photocatalysis process that was evidently proved in electron paramagnetic resonance (EPR) experiment. In addition, the catalyst showed good activity perceived in reusability and stability test due to the synergistic effect between its components. The mechanism of degradation of TC in ABC composite was proposed based on the detailed analysis. The current study will give an efficient and recyclable photocatalyst for antibiotic aqueous pollutant removal.     

Review on heterogeneous oxidation and adsorption for arsenic removal from drinking water

The long term exposure of arsenic via drinking water has resulted in wide occurrence of arsenisim globally, and the oxidation of the non-ionic arsenite (As(III)) to negatively-charged arsenate (As(V)) is of crucial importance for the promising removal of arsenic. The chemical oxidants of ozone, chlorine, chlorine dioxide, and potassium permanganate may achieve this goal; however, their application in developing countries is sometimes restricted by the complicate operation and high cost. This review paper focuses on the heterogeneous oxidation of As(III) by solid oxidants such as manganese oxide, and the adsorption of As(V) accordingly. Manganese oxide may be prepared by both chemical and biological methods to achieve good oxidation performance towards As(III). Additionally, manganese oxide may be combined with other metal oxides, e.g., iron oxide, to improve the adsorption capability towards As(V). Furthermore, manganese oxide may be coated onto porous materials of metal organic frameworks to develop novel adsorbents for arsenic removal. To achieve the application in engineering works, the adsorbents granulation may be achieved by drying and calcination, agglomeration, and the active components may also be in situ coated onto the porous materials to maintain the oxidation and adsorption activities as much as possible. The novel adsorbents with heterogeneous oxidation and adsorption capability may be carefully designed for the removal of arsenic in household purifiers, community-level decentralized small systems, and the large-scale drinking water treatment plants (DWTPs). This review provides insight into the fundamental studies on novel adsorbents, the development of innovative technologies, and the demonstration engineering works involved in the heterogeneous oxidation and adsorption, and may be practically valuable for the arsenic pollution control globally.     

Environmental factors affecting degradation of perfluorooctanoic acid (PFOA) by In2O3 nanoparticles

Nanophotocatalysts have shown great potential for degrading poly-and perfluorinated substances (PFAS).In light of the fact that most of these catalysts were studied in pure water,this study was designed to elucidate effects from common environmental factors on decomposing and defluorinating perfluorooctanoic acid (PFOA) by In₂O₃ nanoparticles.Results from this work demonstrated that among the seven parameters,pH,sulfate,chloride,H₂O₂,In₂O     

Comparison of UV and UV-LED activated sodium percarbonate for the degradation of O-desmethylvenlafaxine

As an active metabolite of venlafaxine and emerging antidepressant, O-desmethylvenlafaxine (ODVEN) was widely detected in different water bodies, which caused potential harm to human health and environmental safety. In this study, the comparative work on the ODVEN degradation by UV (254 nm) and UV-LED (275 nm) activated sodium percarbonate (SPC) systems was systematically performed. The higher removal rate of ODVEN can be achieved under UV-LED direct photolysis (14.99%) than UV direct photolysis (4.57%) due to the higher values of photolysis coefficient at the wavelength 275 nm. Significant synergistic effects were observed in the UV/SPC (80.38%) and UV-LED/SPC (53.57%) systems and the former exhibited better performance for the elimination of ODVEN. The degradation of ODVEN all followed the pseudo-first-order kinetics well in these processes, and the pseudo-first-order rate constant (k_obs) increased with increasing SPC concentration. Radicals quenching experiments demonstrated that both ·OH and CO₃·⁻ were involved in the degradation of ODVEN and the second-order rate constant of ODVEN with CO₃·⁻ (1.58 × 10⁸ (mol/L)⁻¹ sec⁻¹) was reported for the first time based on competitive kinetic method. The introduction of HA, Cl⁻, NO₃⁻ and HCO₃⁻ inhibited the ODVEN degradation to varying degrees in the both processes. According to quantum chemical calculation, radical addition at the ortho-position of the phenolic hydroxyl group was confirmed to be the main reaction pathways for the oxidation of ODVEN by ·OH. In addition, the oxidation of ODVEN may involve the demethylation, H-abstraction, OH-addition and C-N bond cleavage. Eventually, the UV-LED/SPC process was considered to be more cost-effective compared to the UV/SPC process, although the UV/SPC process possessed a higher removal rate of ODVEN.     

Hydrothermal-treated Pt/Al2O3 as an excellent catalyst for toluene total oxidation

The preparation of highly active supported noble metal catalysts with a low noble metal loading has always been the ultimate goal of researchers working on catalysis. Hydrothermally treated Pt/Al₂O₃ (Pt/Al₂O₃-H) exhibits better catalytic activity than that (Pt/Al₂O₃-C) treated via the conventional calcination approach. At the high space velocity of 100,000 mL/(g∙hr), the temperature that correspond to 50% toluene conversion (T₅₀) of Pt/Al₂O₃-H is 115°C lower than that of Pt/Al₂O₃-C, and the turnover frequency (TOF) value can reach 0.0756 sec⁻¹. The mechanism by which the hydrothermal approach enhances Pt/Al₂O₃ activity has been investigated. The structure associated with the high catalytic activity of Pt nanoparticles (NPs) can be retained via hydrothermal treatment. Furthermore, the support is transformed to AlO(OH) with numerous surface hydroxyl groups, which in turn can facilitate the adsorption of toluene. And the synergistic effects of Pt NPs and AlO(OH) increases the contents of Pt in oxidation state and active oxygen, which are beneficial for toluene oxidation.