Enhanced removal of high-As(Ⅲ) from Cl(-Ⅰ)-diluted SO4(-Ⅱ)-rich wastewater at pH 2.3 via mixed tooeleite and(Cl(-Ⅰ)-free) ferric arsenite hydroxychloride formation

An advanced cost-saving method of removal of high-As(Ⅲ) from SO₄(-Ⅱ)-rich metallurgi cal wastewater has been developed by diluting the SO₄(-Ⅱ) content with As(Ⅲ)-Cl(-Ⅰ)-rich metallurgical wastewater and then by the direct precipitation of As(Ⅲ) with Fe(Ⅲ) at pH2.3.As(Ⅲ) removal at various SO₄(-Ⅱ)/Cl(-Ⅰ) molar ratios and temperatures was investigated The results showed that 65.2–98.2%of As(III) immobilization into solids occurred at the SO₄(Ⅱ)/Cl(-Ⅰ) mo...     

Removal of Ni(II) from strongly acidic wastewater by chelating precipitation and recovery of NiO from the precipitates

Strongly acidic wastewater produced in nonferrous metal smelting industries often contains high concentrations of Ni(II), which is a valuable metal. In this study, the precipitation of Ni(II) from strongly acidic wastewater using sodium dimethyldithiocarbamate (DDTC) as the precipitant was evaluated. The effects of various factors on precipitation were investigated, and the precipitation mechanism was also identified. Finally, the nickel in the precipitates was recovered following a pyrometallurgical method. The results show that, under optimised conditions (DDTC:Ni(II) molar ratio = 4:1; temperature = 25 °C), the Ni(II) removal efficiency reached 99.3% after 10 min. In strongly acidic wastewater, the dithiocarbamate group of DDTC can react with Ni(II) to form DDTCNi precipitates. Further recovery experiments revealed that high-purity NiO can be obtained by the calcination of DDTCNi precipitates, with the nickel recovery efficiency reaching 98.2%. The gas released during the calcination process was composed of NO₂, CS₂, H₂O, CO₂, and SO₂. These results provide a basis for an effective Ni(II) recovery method from strongly acidic wastewater.     

Selective recovery of Cu(II) from strongly acidic wastewater by zinc dimethyldithiocarbamate: Affecting factors, efficiency and mechanism

The selective recovery of copper from strongly acidic wastewater containing mixed metal ions remains a significant challenge. In this study, a novel reagent zinc dimethyldithiocarbamate (Zn(DMDC)₂) was developed for the selective removal of Cu(II). The removal efficiency of Cu(II) reached 99.6% after 120 min reaction at 30°C when the mole ratio Zn(DMDC)₂/Cu(II) was 1:1. The mechanism investigation indicates that the Cu(DMDC)₂ products formed as a result of the displacement of Zn(II) from the added Zn(DMDC)₂ by Cu(II) in wastewater, due to the formation of stronger coordination bonds between Cu(II) and the dithiocarbamate groups of Zn(DMDC)₂. Subsequently, we put forward an innovative process of resource recovery for strongly acidic wastewater. Firstly, the selective removal of Cu(II) from actual wastewater using Zn(DMDC)₂, with a removal efficiency of 99.7%. Secondly, high-value CuO was recovered by calcining the Cu(DMDC)₂ at 800°C, with a copper recovery efficiency of 98.3%. Moreover, the residual As(III) and Cd(II) were removed by introducing H₂S gas, and the purified acidic wastewater was used to dissolve ZnO for preparation of valuable ZnSO₄·H₂O. The total economic benefit of resource recovery is estimated to be 11.54 $/m³. Accordingly, this study provides a new route for the resource recovery of the treatment of copper-containing acidic wastewater.     

Phosphate removal from wastewater by model-La（Ⅲ） zeolite adsorbents

Phosphorus is one of the primary nutrients which leads to eutrophication and accelerates aging process in enclosed water bodies. Because of the poor phosphorus selectivity of other adsorbents, the novel La(III)-modified zeolite adsorbent (LZA) was prepared by modifying 90 nm zeolite with lanthanide to selectively remove phosphate in the presence of various omnipresent anions, such as sulfates, bicarbonates, and chlorides. Through batch and fixed bed operation, the following optimum conditions were obtained: concentration of lanthanum chloride solution 0.05 mol/L; solid/liquor ratio 1/25; pH 10; calcination temperature 550℃; time 1 h. The value of the Freundlich model constants Kf and 1/n were found to be 16.76 mg/L and 0.2209, respectively. In addition, when calculated at pH 6.0, distribution coe cient KD could be as high as 36.6. Furthermore, in the alkaline pH range, solution of 0.8 mol/L NaCl was used to regenerate the saturated LZA, which could reach the high regeneration e ciency as high as 100%. Because of the good selectivity and regenerability of LZA, it might serve as a potential way for advanced phosphate removal from the sewage containing other anions.     

Simultaneous removal of NO and dichloromethane（CH2Cl2） over Nb-loaded cerium nanotubes catalyst

Herein, a series of niobium oxide supported cerium nanotubes（Ce NTs） catalysts with different loading amount of Nb₂O₅（0–10 wt.%） were prepared and used for selective catalytic reduction of NOxwith NH₃（NH₃-SCR） in the presence of CH₂Cl₂. Commercial V₂O₅-WO₃-TiO₂ catalyst was also prepared for comparison. The physcial properties and chemical properties of the Nb₂O₅ lo...     

Ammonium removal by modified zeolite from municipal wastewater

Ammonium removal by modified zeolite, H-form and Na-form zeolite, were examined by batch-type methods. The adsorption of ammonium on modified zeolite was exothermic process. The saturation adsorption capacity of ammonium on H-form and Na-form zeolite were 21.23 and 41.1.5 mg/g, respectively. After ten times adsorption-desorption-readsorption cycles the standard deviations of H-form and Na-form zeolite were 6.34% and 6.59%. The zeolite adsorption process has proved cost effective and practical in reducing ammonium by H-form and Na-form zeolite in municipal wastewater from concentration 27.68 mg/L to 2.80 mg/L and 5.91 mg/L.     

天然菱铁矿去除水中磷的性能研究

采用批次试验研究菱铁矿对水溶液中磷的吸附特性,考察了初始磷浓度、p H值、菱铁矿投加量、粒径、共存离子对吸附的影响,并探讨了吸附动力学和吸附热力学特征.结果表明,当磷溶液初始浓度为20 mg·L-1,初始p H为6.0时,菱铁矿对磷的吸附效果较好,吸附平衡时间为48h.菱铁矿投加量为0.5~10 g时,随着投加量的增加,菱铁矿对磷的吸附效能逐渐提高.相对于NO-3、Cl-而言,SO2-4、HCO-3对菱铁矿去除磷有微弱的抑制作用.动力学研究发现,菱铁矿对磷的吸附过程更符合准二级动力学模型,吸附平衡可由Freundlich等温线方程描述,饱和吸附量为83.5μg·g-1.最后分别计算了288、303和318 K下的吸附热力学参数,发现吉布斯自由能(ΔG)均为负,焓变(ΔH)及熵变(ΔS)为正,表明该吸附过程为自发的吸热反应.     

焦化废水厌氧氨氧化生物脱氮的研究

采用厌氧氨氧化(ANAMMOX)工艺处理焦化废水,在厌氧34℃、pH值7.5~8.5,HRT为33h的条件下,经过115d成功启动厌氧氨氧化反应器.当进水NH4+-N、NO2--N浓度分别为80、90mg/L左右时, TN负荷可达160mg/(L·d),系统NH4+-N和NO2--N的去除率最高分别达86%和98%,TN去除率可达75%. GC-MS分析结果表明,酚类是焦化废水中较易被生物利用的有机物,ANAMMOX过程对好氧短程硝化工艺出水残余低浓度酚类有机物有进一步去除作用.     

San copolymer membranes with ion exchangers for Cu(II) removal from synthetic wastewater by electrodialysis

Heterogeneous membranes were obtained by using styrene-acrylonitrile copolymer (SAN) blends with low content of ion-exchanger particles (5 wt.%). The membranes obtained by phase inversion were used for the removal of copper ions from synthetic wastewater solutions by electrodialytic separation. The electrodialysis was conducted in a three cell unit, without electrolyte recirculation. The process, under potentiostatic or galvanostatic control, was followed by pH and conductivity measurements in the solution. The electrodialytic performance, evaluated in terms of extraction removal degree (rd) of copper ions, was better under potentiostatic control then by the galvanostatic one and the highest (over 70%) was attained at 8 V. The membrane efficiency at small ion-exchanger load was explained by the migration of resin particles toward the pores surface during the phase inversion. The prepared membranes were characterized by various techniques i.e. optical microscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, thermogravimetric analysis and differential thermal analysis and contact angle measurements.     

生物矿化促进造纸废水好氧除钙的技术研究

造纸废水厌氧出水中钙离子浓度高,容易引起后续活性污泥好氧曝气系统钙化,造成生化处理能力下降.本文利用富含产脲酶菌的驯化污泥对模拟厌氧出水进行生物矿化除钙.在序批式反应器中接种驯化污泥,在一定尿素浓度下研究除钙过程,并考察曝气对除钙过程的影响.结果表明,当尿素投加量为0.5 g·L^-1时,不曝气条件下钙和有机物去除率分别达到50%和35%左右;曝气有利于吹脱二氧化碳,当曝气量为0.2 L·min^-1时,钙离子和有机物去除率均上升至80%左右,而持续提高曝气量无法进一步提高有机物去除率.综合运行成本和处理要求,曝气辅助生物矿化可以有效去除造纸废水厌氧出水中的溶解性钙离子.通过基因组测序发现驯化污泥中产脲酶功能菌主要来自厚壁菌门,特别是芽孢杆菌纲中的热杆菌属.     

混凝和强化混凝对印染废水中锑(Ⅴ)的去除特性

印染废水中锑的排放标准日趋严格,是印染废水处理面临的新挑战.以混凝和强化混凝去除印染废水中锑(Ⅴ)为目标,发现聚硫酸铁(PFS)混凝剂对印染废水中锑(Ⅴ)的去除效率显著优于铁铝复配混凝剂和铝盐混凝剂,去除效率达97.4%,出水锑(Ⅴ)浓度可达4μg·L~(-1).酸性条件(低水解度)有利于PFS生成Fe(a)活性组分和静电吸引、锑(Ⅴ)迁移,且絮体颗粒较小,促进PFS混凝除锑(Ⅴ)效率;酸性条件下PFS除锑(Ⅴ)效率是中性条件的1.27倍,处理出水中锑(Ⅴ)浓度仅为中性条件的33.3%.PFS投加量与除锑(Ⅴ)效率符合反比例模型.在较高锑(Ⅴ)浓度下,提升PFS投加量可提高除锑(Ⅴ)效率,但在较低锑(Ⅴ)浓度下,提升PFS投加量对除锑(Ⅴ)效率的促进较小.PFS絮体回流与混凝沉淀串联或耦合可显著提升印染废水中锑(Ⅴ)的去除效率,其除锑(Ⅴ)效率分别是单一PFS混凝沉淀的1.14倍和1.32倍,可有效降低出水锑(Ⅴ)浓度并节约PFS投加量和减少污泥生成量.其中混凝-絮体回流耦合工艺中,最佳絮体回流比例为100%.     

白云石石灰流化结晶污水除磷工艺

实验研究了白云石石灰流化床工艺除磷的可行性.石灰一方面可以提高水体的pH值并提供充足的Ca2+、Mg2+,另一方面可作为晶种加快结晶沉淀反应,提高磷去除效率,是一种廉价高效的药剂.设计了新型气体搅动式白云石石灰流化床结晶反应器,以模拟污水厂污泥厌氧消化上清液为处理对象,实验考察了药剂投加量、停留时间和曝气量对反应器运行的影响.结果表明:药剂投加量在600~650 mg·L-1、停留时间5.0 h及曝气量50 mL·min-1的条件下,可以获得较好的磷去除效果,去除率可达87.0%.采用扫描电子显微镜、X射线衍射和傅里叶变换红外光谱对产物进行了表征,发现磷主要以磷酸铵镁(MAP)和羟基磷灰石(HAP)两种形式去除;由于反应体系碱度较高,产物中混杂大量CaCO3.     

SRV菌去除电镀废水中铜的研究

为探索新的铜废水处理方法,更有效地治理铜废水造成的环境污染,用微生物及电镜法对SRV菌去除电镀废水中铜进行了研究。研究了菌量、铜离子浓度、溶液的pH值、作用的温度和时间等因素对SRV菌去除溶液中铜离子的影响。在菌废比1:1的情况下,对铜浓度为246.8mg/L的废水去除率达99.12％。观察了SRV菌处理铜废水前、后的扫描电镜、超薄切片透射电镜,推测其去除机制为铜与SRV菌代谢产物反应生成沉淀或直接被吸附于菌体表面而去除。     

脱硫石膏基羟基磷灰石对Cu2+吸附性能的研究

以燃煤电厂废弃物脱硫石膏(FGD)为主要原料,利用水热合成法制备羟基磷灰石(FGD-HA),利用XRD和SEM对FGD-HA的物相组成和微观形貌进行了分析和观察.通过静态吸附实验研究了吸附动力学、吸附等温线以及吸附热力学.结果表明,伪二级动力学模型相关系数为0.9998,是描述FGD-HA吸附Cu2+的最佳动力学模型,Cu2+在FGD-HA上的吸附平衡符合Langmuir等温线模型(R2=0.9846),热力学表明此吸附是自发吸热的过程.利用响应面分析法对Cu2+的吸附条件进行优化,得出投加量3.11g/L、pH值4.96、温度22.09℃、Cu2+初始浓度24.75mg/L为最佳吸附条件,此条件下Cu2+去除率预测值为100%,相同条件下开展的验证实验结果为97.4%,与预测值相接近说明模型的选择是实际可行的.     

高效污水处理器(XYZ型)在医院废水处理中的应用

本文旨在阐明经济有效、处理能力强的高效污水处理器,在医院中实际运行的效果,提出当前市、县医院有借鉴意义的废水治理对策.     

Synthesis of a novel illite@carbon nanocomposite adsorbent for removal of Cr(VI) from wastewater

A novel illite@carbon (I@C) nanocomposite adsorbent has been synthesized via a facile hydrothermal carbonization process (HTC) using glucose as carbonaceous source and illite as the carrier. The morphology, microstructure and surface properties of the prepared nanocomposite adsorbent were analyzed by FESEM, TGA, XRD, FT-IR and Zeta potential measurements. Batch experiments were carried out on the adsorption of Cr(VI) to determine the adsorption properties of the composite. The adsorption of Cr(VI) onto the I@C nanocomposite was well described by the pseudo-second-order kinetic model and Langmuir isotherm. Compared with the illite and carbon material (SC) separately, the prepared I@C nanocomposite adsorbent exhibited enhanced adsorption performance for Cr(VI) with a maximum adsorption capacity of 149.25 mg/g, which was higher than that of most reported adsorbents. In addition, the adsorption process was spontaneous and endothermic based on the adsorption thermodynamics study. The adsorption of Cr(VI) by I@C was highly pH-dependent and the optimum adsorption occurred at pH 2.0. The Zeta potential analysis results indicated that the electrostatic interactions between anionic Cr(VI) and the positively charged surface of the adsorbent might be critical to the adsorption mechanism. This study demonstrated that the I@C nanocomposite should be a promising candidate for a low-cost, environmental friendly and highly efficient adsorbent for the removal of toxic Cr(VI) from wastewater.     

Na_2S-DDTC深度处理络合Ni高浓度电镀废水

对比选用有机巯基类高分子螯合剂(DDTC)、无机硫(Na_2S)和氢氧化钠(Na OH)作为电镀Ni的捕集剂,对模拟电镀废水中的络合Ni进行深度处理,重点考察了反应p H值、药剂投加量、反应时间以及絮凝剂种类等因素对Ni的去除效果的影响,并对去除机理进行了探究.结果表明:对于高浓度络合Ni模拟废水ρ(Ni)=300mg/L,在p H9.0,Na_2S与DDTC投加比为ρ(Na_2S)/ρ(DDTC)=10,其中ρ(Na_2S)=600mg/L,ρ(DDTC)=60mg/L,反应时间t=6.0min,PAM投加量1.0mg/L时,Ni_2+的残余浓度为0.064mg/L,低于0.1mg/L达到废水排放标准;此外对Na_2S-DDTC与Ni反应生成的沉淀的溶出试验表明,在自然状态下该沉渣具有较高的稳定性,不会形成二次污染;通过粒径分布统计分析以及SEM表面形态观察分析可知Na_2S-DDTC复配药剂对Ni的捕集作用主要为有絮凝-共沉淀的协同作用.通过本研究,可以为Na_2S-DDTC处理高浓度含络合Ni电镀废水工艺设计提供理论支持.     

沸石的活化及其对水中氨氮的吸附

对天然沸石进行了盐活化、盐加酸活化、盐加碱活化、热活化和热活化后加盐二次活化的处理,分别考察了活化后沸石对氨氮的吸附性能,并进行了等温吸附、解吸试验以及对经SBR-氧化处理后焦化废水的吸附试验.结果表明,沸石在100℃下经0.3 mol·L-1NaCl活化后,对氨氮的吸附效果最佳;当活化沸石投加量为10 g·L-1、接触时间为40 min时,氨氮去除率可达88.08%,比未活化条件下的47.35%提高了40.73%.沸石投加量、废水的pH和接触时间对活化沸石吸附氨氮都存在一定的影响.活化沸石对氨氯废水的吸附等温线可用Freundlich方程拟合.吸附氨氮后的沸石经1.5 mol·L-1的NaCl溶液再生4 h,解吸率可达到89.30%.活化沸石用于经SBR-氯化处理后焦化废水的吸附试验,当活化沸石投加量为120 g·L-1时,其氨氮可从219.18 mg·L-1降到4.8 mg·L-1去除率达到97.81%;活化沸石吸附焦化废水的吸附等温线可用Freundlich方程和Langmuir方程来描述.     

Cadmium removal from wastewater by sponge iron sphere prepared by hydrogen reduction

A new type of sponge iron sphere (NSIS) with 1-5 mm diameter, made of concentrated iron powder and possessed high activity and intension, was prepared by mini-pellet sintering integrated with H₂ direct reduction. Static state experiment has been carried on to investigate the Cd²⁺ removal efficiency from wastewater by the NSIS and to explore the Cd²⁺ removal reaction kinetics. It was suggested that initial pH value and Cd²⁺ original concentration had significant influence on Cd²⁺ removal percentage. Cd²⁺ removal percentage decreased significantly with the increasing of Cd²⁺original concentration whether the original pH value be adjusted to 3.0 or without adjustment. The results showed that the Cd²⁺ removal process followed the first order reaction because the reaction order was from 0.803 to 0.996. The apparent reaction rate constant between Cd²⁺ and NSIS was from 0.0025 to 0.1000 (mg·L^?1)^1-n·min^?1. Compared with SIS reduced by charcoal reduction, NSIS deoxided by hydrogen possessed higher activity, and could remove the same quantity of Cd²⁺ within a shorter period of time.     

生活污水短程生物脱氮过程中N2O的产生与控制方法

 为降低和控制实际污水处理厂中N2O产生量,通过长期试验和间歇试验对SBR法实际生活污水全程及短程脱氮过程中N2O的主要产生源和影响因素进行了研究.结果表明:生活污水短程硝化反硝化过程中有N2O产生,并且N2O主要产生于短程硝化过程中,即氨氧化过程中,而反硝化作用没有N2O产生,且能够将氨氧化结束时,活性污泥中累积的溶解性N2O进一步还原为N2.短程硝化过程中,N2O产生量随进水氨氮浓度的升高而显著增加.DO浓度对N2O的产生与释放有重要的影响,DO浓度高于2mg/L和低于0.5mg/L N2O产生量均较低.DO低于0.5mg/L时,一方面,降低了曝气作用对N2O的吹脱,延长了N2O在活性污泥中的停留时间;另一方面,在活性污泥絮体内部形成缺氧区,促进了同步硝化反硝化,在硝化作用的同时,加强了反硝化作用对N2O的还原作用,利于N2O的减量控制.