Preparation of effective TiO<Subscript>2</Subscript>/Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> photocatalysts for water treatment

Photocatalytic oxidation using semiconductors is one of the advanced oxidation processes for degradation of organic pollutants in water and air. TiO₂ is an excellent photocatalyst that can mineralize a large range of organic pollutants such as pesticides and dyes. The main challenge is to improve the efficiency of the TiO₂ photocatalyst and to extend TiO₂ light absorption spectra to the visible region. A potential solution is to couple TiO₂ with a narrow band gap semiconductor possessing a higher conduction band such as bismuth oxide. Therefore, here we prepared Bi₂O₃/TiO₂ heterojunctions by the impregnation method with different Bi/Ti ratio. The prepared composites have been characterized by UV–Vis diffused reflectance spectra and X-ray diffraction. The photocatalytic activity of the heterojunction has been determined from the degradation of orange II under visible and UV light. Results show that Bi₂O₃/TiO₂ heterojunctions are more effective than pure TiO₂-anatase under UV-A irradiation, with an optimum for the Bi/Ti ratio of 5 %, for the photocatalytic degradation of Orange II. However, the photocatalytic activity under irradiation at λ higher than 420 nm is not much improved. Under UV–visible radiation, the two semiconductors are activated. We propose a mechanism explaining why our products are more effective under UV–visible irradiation. In this case the charge separation is enhanced because a part of photogenerated electrons from the conduction band of TiO₂ will go to the conduction band of bismuth oxide. In this composite, titanium dioxide is the main photocatalyst, while bismuth oxide acts as adsorbent photosensitizer under visible light.     

Solar photocatalytic decomposition of two azo dyes on multi-walled carbon nanotubes (MWCNTs)/TiO<Subscript>2</Subscript> composites

Multi-walled carbon nanotubes (MWCNTs)/TiO₂ composite photocatalysts with high photoactivity were prepared by sol-gel process and further characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared (FT-IR), and UV-vis absorption spectra. Compared to pure TiO₂, the combination of MWCNTs with titania could cause a significant absorption shift toward the visible region. The photocatalytic performances of the MWCNTs/TiO₂ composite catalysts were evaluated for the decomposition of Reactive light yellow K-6G (K-6G) and Mordant black 7 (MB 7) azo dyes solution under solar light irradiation. The results showed that the addition of MWCNTs enhanced the adsorption and photocatalytic activity of TiO₂ for the degradation of azo dyes K-6G and MB 7. The effect of MWCNTs content, catalyst dosage, pH, and initial dye concentration were examined as operational parameters. The kinetics of photocatalytic degradation of two dyes was found to follow a pseudo-first-order rate law. The photocatalyst was used for seven cycles with photocatalytic degradation efficiency still higher than 98%. A plausible mechanism is also proposed and discussed on the basis of experimental results.     

Pt/Mg-Ce-O catalyst for NO/H<Subscript>2</Subscript>/O<Subscript>2</Subscript> lean de-No<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> reaction

The NO/H₂/O₂ reaction was studied under oxidizing conditions in the 100-400 °C range over 0.1 wt% Pt supported on various metal oxides such as MgO, CeO₂, SiO₂, La₂O₃, CaO, Y₂O₃ and TiO₂. The Pt/MgO and Pt/CeO₂ catalysts showed good catalytic behaviours. Here, we find that the Pt/Mg-Ce-O catalyst, prepared from MgO and CeO₂ by the sol-gel method, is a very active and selective catalyst towards N₂ formation in the whole 100–400 °C range. This catalyst appears to be the most active, selective and stable one ever reported in the literature for the NO/H₂/O₂ reaction, even in the presence of 5%v H₂O or 20 ppmv of SO₂ in the feed stream.Selected article from the Regional Symposium on Chemistry and Environment, Krusevac, Serbia, June 2003, organised by Dr. Branimir Jovancicevic.     

Iron-doped copper 1,4-benzenedicarboxylate as photo-Fenton catalyst for degradation of methylene blue

Abstract

A metal-organic framework of iron-doped copper 1,4-benzenedicarboxylate was synthesized and, for the first time, utilized as a heterogeneous photo-Fenton catalyst for degradation of methylene blue dye in aqueous solution under visible light irradiation. The synthesized materials were characterized by scanning electron microscopy, Fourier-transform infrared spectroscopy, X-ray diffraction and energy-dispersive X-ray spectroscopy. The influence factors, kinetics, and stability of the synthesized catalysts were investigated in detail. Iron-doped copper 1,4-benzenedicarboxylate showed higher degradation efficiency than pure copper 1,4-benzenedicarboxylate. An almost complete degradation was achieved within 70?min under visible light irradiation at a solution pH of 6, a catalyst loading of 1?g?L^?1, a H₂O₂ dosage of 0.05?mol L^?1 and methylene blue concentration of 50?mg?L^?1. Recycling studies demonstrated that the iron-doped copper 1,4-benzenedicarboxylate is a promising heterogeneous photo-Fenton catalyst for long-term removal of methylene blue dye from industrial wastewater.     

Decolorisation of Acid Blue 74 by ultraviolet/H<Subscript>2</Subscript>O<Subscript>2</Subscript>

The photodegradation of Acid blue 74 in aqueous solution employing a H₂O₂/ultraviolet system in a photochemical reactor was investigated. The kinetics of decolorization were studied by application of a kinetic model. The results show that the reaction of decolorization followed pseudo-first order kinetics. We demonstrate that there is an optimum H₂O₂ concentration, at which the rate of the decolorization reaction is maximum. Irradiation at 253.7 nm of the dye solution in the presence of H₂O₂ results in complete discoloration after ten minutes of treatment.     

Investigation of the effects of humic acid and H<Subscript>2</Subscript>O<Subscript>2</Subscript> on the photocatalytic degradation of atrazine assisted by microwave

A solution of atrazine in a TiO₂ suspension, an endocrine disruptor in natural water, was tentatively treated by microwave-assisted photocatalytic technique. The effects of mannitol, oxygen, humic acid, and hydrogen dioxide on the photodegradation rate were explored. The results could be deduced as follows: the photocatalytic degradation of atrazine fits the pseudo-first-order kinetic well with k = 0.0328 s^?1, and ·OH was identified as the dominant reactant. Photodegradation of atrazine was hindered in the presence of humic acid, and the retardation effect increased as the concentration of humic acid increased. H₂O₂ displayed a significant negative influence on atrazine photocatalysis efficiency. Based on intermediates identified with gas chromatography-mass spectrometry (GC-MS) and Liquid chromatography-mass spectrometry (LC-MS/MS) techniques, the main degradation routes of atrazine are proposed.     

Preparation and characterization of a new TiO2/SiO2 composite catalyst for photocatalytic degradation of indigo carmin

The TiO₂/SiO₂ composite was prepared by means of the SiO₂-particle-entrapment method. The FTIR data showed the presence of Si–O–Ti stretching vibration band at 970 cm⁻¹ in the TiO₂/SiO₂ composite, suggesting a reaction between TiO₂ and silica on the TiO₂ particle surface during the silicagel formation around the TiO₂ particles. The photocatalytic efficiency of TiO₂ immobilized in silicagel was compared with that of the conventional TiO₂ Degussa P25 catalyst. For this purpose, the degradation of indigo carmin (IC) dye was used as model molecule in the tests. The effect of operational parameters such as catalyst loading and dye concentration on the photocatalytic degradation of the model dye was investigated. The rate of degradation increased with increasing catalyst loading, and when the concentration of the dye decreases.     

Degradation of carbendazim by UV/H<Subscript>2</Subscript>O<Subscript>2</Subscript> investigated by kinetic modelling

The transformation of the fungicide carbendazim (methyl-2 benzimidazole carbamate) induced by hydroxyl radical generated by the UV photolysis of H₂O₂ has been studied in dilute aqueous solution. The efficient reaction of hydroxyl radicals with carbendazim led to the rapid degradation of carbendazim. The study of reaction kinetics yielded a second order rate constant of 2.2±0.3 10⁹ M⁻¹ s⁻¹ for HO^· radicals with carbendazim. This value is in agreement with a high reactivity of HO^· radicals with carbendazim. Most degradation products were identified by high performance liquid chromatography mass spectrometry (HPLC-MS). In the presence of hydrogenocarbonate and carbonate ions, hydroxyl radicals were quenched and in turn carbonate radicals CO₃ ^·− were formed. Carbonate radicals are indeed known to react efficiently with compounds containing electron-rich sites such as nitrogen or sulfur atoms. The use of a kinetic modelling software gave evidence for the occurrence of such reactions with carbendazim. The second order rate constant of carbonate radical with carbendazim was equal to 6±2 10⁶ M⁻¹ s⁻¹. Electronic Publication     

Enhanced photocatalytic activity of electrospun TiO2/polyacrylonitrile membranes in a crossflow reactor using dual lights

Photocatalytic membranes reactors have become one of the most efficient technologies to treat polluted waters. However, a major drawback is the unilateral irradiation of the membrane, where only one side of the membrane is exploited. To overcome this issue, we developed a reactor where the membrane can be irradiated on both sides. Polyacrylonitrile membranes containing different amounts of TiO₂ nanoparticles up to 60% were first prepared by electrospinning. These membranes were used in a 3D-printed crossflow photocatalytic membrane reactor for the degradation of methylene blue under different combinations of lights. The use of both sides of the photocatalytic membrane significantly enhanced the photocatalytic activity for the decolorization of methylene blue in water. The prepared membranes showed the best decolorization rate for a loading of 60% of TiO₂ and the use of dual ultraviolet lights, where the methylene blue solution was completely discolored after 90 min. This is the first report of a such system configuration, and this new irradiation concept is promising for photocatalytic membrane reactions and water cleaning.

     

An electrochemical process that uses an Fe<Superscript>0</Superscript>/TiO<Subscript>2</Subscript> cathode to degrade typical dyes and antibiotics and a bio-anode that produces electricity

In this study, a new water treatment system that couples (photo-) electrochemical catalysis (PEC or EC) in a microbial fuel cell (MFC) was configured using a stainless-steel (SS) cathode coated with Fe⁰/TiO₂. We examined the destruction of methylene blue (MB) and tetracycline. Fe⁰/TiO₂ was prepared using a chemical reduction-deposition method and coated onto an SS wire mesh (500 mesh) using a sol technique. The anode generates electricity using microbes (bio-anode). Connected via wire and ohmic resistance, the system requires a short reaction time and operates at a low cost by effectively removing 94% MB (initial concentration 20 mg?L^–1) and 83% TOC/TOC₀ under visible light illumination (50 W; 1.99 mW?cm^–2 for 120 min, MFC-PEC). The removal was similar even without light irradiation (MFC-EC). The E _Eo of the MFC-PEC system was approximately 0.675 kWh?m^–3?order^–1, whereas that of the MFC-EC system was zero. The system was able to remove 70% COD in tetracycline solution (initial tetracycline concentration 100 mg?L^–1) after 120 min of visible light illumination; without light, the removal was 15% lower. The destruction of MB and tetracycline in both traditional photocatalysis and photoelectrocatalysis systems was notably low. The electron spinresonance spectroscopy (ESR) study demonstrated that ?OH was formed under visible light, and ?O ₂ ^– was formed without light. The bio-electricity-activated O₂ and ROS (reactive oxidizing species) generation by Fe⁰/TiO₂ effectively degraded the pollutants. This cathodic degradation improved the electricity generation by accepting and consuming more electrons from the bio-anode.

Open image in new window

     

Photocatalytic degradation of the herbicide cinosulfuron in aqueous TiO<Subscript>2</Subscript> suspension

The photocatalytic degradation of a sulfonylurea herbicide, cinosulfuron, has been studied in TiO₂ aqueous suspensions. A first order kinetic law was found. The influence of the initial concentration of cinosulfuron and of the initial radiant flux on the kinetics were evaluated. The identification of the intermediate products was based on high performance liquid chromatography coupled with mass spectrometry analyses (HPLC-MS). The mineralization of cinosulfuron was traced using ion chromatography and total organic carbon (TOC) measurements. These results indicate that the photocatalytic degradation of cinosulfuron leads to CO₂, NO₃ ⁻ and SO₄ ²⁻ as final products, and in addition cyanuric acid (C₃H₃O₃N₃), confirming previous results on triazinic ring-containing compounds. Electronic Publication     

Promotion of transition metal oxides on the NH<Subscript>3</Subscript>-SCR performance of ZrO<Subscript>2</Subscript>-CeO<Subscript>2</Subscript> catalyst

Chromium oxide and manganese oxide promoted ZrO₂-CeO₂ catalysts were prepared by a homogeneous precipitation method for the selective catalytic reduction of NO _x with NH₃. A series of characterization including X-ray diffraction (XRD), high-resolution transmission electron microscope (HR-TEM), Brunauer–Emmett–Teller (BET) surface area analysis, H₂ temperatureprogrammed reduction (H₂-TPR), and X-ray photoelectron spectroscopy (XPS) were used to evaluate the influence of the physicochemical properties on NH₃-SCR activity. Cr-Zr-Ce and Mn-Zr-Ce catalysts are much more active than ZrO₂-CeO₂ binary oxide for the low temperature NH₃-SCR, mainly because of the high specific surface area, more surface oxygen species, improved reducibility derived from synergistic effect among different elements. Mn-Zr-Ce catalyst exhibited high tolerance to SO₂ and H₂O. Cr-Zr-Ce mixed oxide exhibited>80% NO _x conversion at a wide temperature window of 100°C–300°C. In situ DRIFT studies showed that the addition of Cr is beneficial to the formation of Bronsted acid sites and prevents the formation of stable nitrate species because of the presence of Cr^{6 +}. The present mixed oxide can be a candidate for the low temperature abatement of NO _x .

Open image in new window

     

Effective degradation of tetracycline by mesoporous Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript> under visible light irradiation

Bi₂WO₆ was synthesized with a hydrothermal method at different pHs and used for the degradation of tetracycline (TC) in water. The mesoporous Bi₂WO₆ prepared at pH 1 (BWO-1) displayed the highest adsorption and degradation capacity to TC due to its large surface area and more efficient capacity to separate photogenerated electrons and holes. 97% of TC at 20 mg·L^?1 was removed by BWO-1 at 0.5 g·L^?1 after 120 min irradiation under simulated solar light. Only 31% of the total organic carbon (TOC) was removed after 360 min irradiation although the TC removal reached 100%, suggesting that TC was mainly transformed to intermediate products rather than completely mineralized. The intermediates were identified by high-performance liquid chromatography-time of flight-mass spectrometry (HPLC-TOF-MS) and possible photodegradation pathways were proposed.     

Fabrication and photocatalytic ability of an Au/TiO<Subscript>2</Subscript>/reduced graphene oxide nanocomposite

A new type of Au/TiO₂/reduced graphene oxide (RGO) nanocomposite was fabricated by the hydrothermal synthesis of TiO₂ on graphene oxide followed by the photodeposition of Au nanoparticles. Transmission electron microscopy images showed that Au nanoparticles were loaded onto the surface of both TiO₂ and RGO. Au/TiO₂/RGO had a better photocatalytic activity than Au/ TiO₂ for the degradation of phenol. Electrochemical measurements indicated that Au/TiO₂/RGO had an improved charge transfer capability. Meanwhile, chemiluminescent analysis and electron spin resonance spectroscopy revealed that Au/TiO₂/RGO displayed high production of hydrogen peroxide and hydroxyl radicals in the photocatalytic process. This high photocatalytic performance was achieved via the addition of RGO in Au/TiO₂/RGO, where RGO served not only as a catalyst support to provide more sites for the deposition of Au nanoparticles but also as a collector to accept electrons from TiO₂ to effectively reduce photogenerated charge recombination.

Open image in new window

     

Visible light sensitive activated carbon-metal oxide (TiO2, WO3, NiO,and SnO) nano-catalysts for photo-degradation of methylene blue: a comparative study

Four composites of metal oxide doped with activated carbon with a metal oxide weight of 20% were prepared using mechano-mixing method. The nano-catalysts were characterized by N₂-adsorption–desorption, X-ray diffraction analysis, transmission electron microscopy, Fourier-transform infrared spectroscopy, UV-diffuse reflectance, and photoluminescence spectroscopy. Photo-catalytic degradation of methylene blue dye under UV 254 nm and visible light was examined. In general, prepared catalysts are more active for degradation of dye under visible light than UV, reaching 96% within 180?min irradiation using the SnO catalyst. Photo-degradation of methylene blue followed pseudo first order reaction mechanism with a rate constant of 14.8?×?10^?3?min^?1, and the time required for removal of 50% of dye was 47?min.     

Ag–TiO2 doped photo catalytic degradation of Procion blue H-B dye in textile washwater

The photocatalytic degradation of Procion blue H-B dye in biodegraded textile washwater has been investigated for the complete removal of color and maximum reduction of chemical oxygen demand (COD). Pseudomonas putida was utilized for obtaining biodegraded textile washwater. In this process, silver-doped TiO₂ photocatalyst was prepared and experiments were carried out to study the effects of UV and mercury lamp irradiations on COD reduction and removal of color. The thus prepared silver-doped TiO₂ catalyst was characterized by thermogravimetric and differential thermal analysis, UV-visible spectrometer, X-ray diffraction, scanning electron microscope, energy dispersive X-ray microanalysis, and BET surface area techniques. Adsorption studies were also carried out to evaluate the fitness of isotherm models. The results show that the silver-doped TiO₂ has enhanced the photodegradation of Procion blue H-B dye under UV and mercury lamp irradiations. The enhanced activity of silver-doped TiO₂ is due to the enrichment of electron–hole separation by electron trapping of silver particles.     

Enhanced heterogeneous Fenton-like activity by Cu-doped BiFeO<Subscript>3</Subscript> perovskite for degradation of organic pollutants

Heterogeneous Fenton-like reaction has been extensively investigated to eliminate refractory organic contaminants in wastewater, but it usually shows low catalytic performance due to difficulty in reduction from Fe(III) to Fe(II). In this study, enhanced catalytic efficiency was obtained by employing Cu-doped BiFeO₃ as heterogeneous Fenton-like catalysts, which exhibited higher catalytic performance toward the activation of H₂O₂ for phenol degradation than un-doped BiFeO₃. BiFe_0.8Cu_0.2O₃ displayed the best performance, which yielded 91% removal of phenol (10 mg L^–1) in 120 min. The pseudo first-order kinetic rate constant of phenol degradation in BiFe_0.8Cu_0.2O₃ catalyzed heterogeneous Fenton-like reaction was 5 times higher than those of traditional heterogeneous Fenton-like catalysts, such as Fe₃O₄ and goethite. The phenol degradation efficiency could still reach 83% after 4 cycles, which implied the good stability of BiFe_0.8Cu_0.2O₃. The high catalytic activity of BiFe_0.8Cu_0.2O₃ was attributed to the fact that the doping Cu into BiFeO₃ could promote the generation of Fe(II) in the catalyst and then facilitate the activation of H₂O₂ to degrade the organic pollutants.

Open image in new window

     

Fe（0）/H_2O_2协同降解亚甲基蓝的研究

进行了Fe（0）和H2O2协同催化降解亚甲基蓝的研究,分析了Fe（0）投加量、H2O2投加量、溶液初始pH值和染料初始质量浓度等因素的影响。研究表明：Fe（0）和H2O2协同可有效催化降解亚甲基蓝;在pH为4.5,Fe（0）用量为2.0 g.L-1,H2O2用量为3.0 mmol.L-1时对10 mg.L-1亚甲基蓝的去除率在60 min内达到90%以上。MB的降解去除率随着Fe（0）投加量与H2O2用量的增加而增加,但随着其初始质量浓度的增大而降低。研究结果还表明,Fe（0）和H2O2可在接近中性条件下有效协同催化降解亚甲基蓝。UV-Vis光谱在反应过程的变化说明亚甲基蓝降解生成了一些小分子物质。     

Photocatalytic degradation of organic dyes by Er<Superscript>3+</Superscript>:YAlO<Subscript>3</Subscript>/TiO<Subscript>2</Subscript> composite under solar light

In this work, Er³⁺:YAlO₃/TiO₂ composite was synthesized by a ultrasonic dispersion and liquid boil method. The Er³⁺:YAlO₃/TiO₂ composite and pure TiO₂ powder were characterized by XRD. The degradation of different organic dyes was used to evaluate the photocatalytic activity of the Er³⁺:YAlO₃/TiO₂ composite. It is found that the photocatalytic activity of Er³⁺:YAlO₃/TiO₂ composite is much higher than that for the similar system with only TiO₂. Moreover, this Er³⁺:YAlO₃/TiO₂ composite provides a new way to take advantage of TiO₂ in sewage treatment aspects using solar light.     

Effects of Pd doping on N<Subscript>2</Subscript>O formation over Pt/BaO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> during NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> storage and reduction process

N₂O is a powerful greenhouse gas and plays an important role in destructing the ozone layer. This present work investigated the effects of Pd doping on N₂O formation over Pt/BaO/Al₂O₃ catalyst. Three types of catalysts, Pt/BaO/Al₂O₃, Pt/Pd mechanical mixing catalyst (Pt/BaO/Al₂O₃ + Pd/Al₂O₃) and Pt-Pd co-impregnation catalyst (Pt-Pd/BaO/Al₂O₃) were prepared by incipient wetness impregnation method. These catalysts were first evaluated in NSR activity tests using H₂/CO as reductants and then carefully characterized by BET, CO chemisorption, CO-DRIFTs and H2-TPR techniques. In addition, temperature programmed reactions of NO with H2/CO were conducted to obtain further information about N₂O formation mechanism. Compared with Pt/BaO/Al₂O₃, (Pt/BaO/ Al₂O₃ + Pd/Al₂O₃) produced less N₂O and more NH3 during NO _x storage and reduction process, while an opposite trend was found over (Pt-Pd/BaO/Al₂O₃ + Al₂O₃). Temperature programmed reactions of NO with H₂/CO results showed that Pd/Al₂O₃ component in (Pt/BaO/Al₂O₃ + Pd/Al₂O₃) played an important role in NO reduction to NH₃, and the formed NH3 could reduce NO _x to N₂ leading to a decrease in N₂O formation. Most of N₂O formed over (Pt-Pd/BaO/Al₂O₃ + Al₂O₃) was originated from Pd/BaO/Al₂O₃ component. H₂-TPR results indicated Pd-Ba interaction resulted in more difficultto- reduce PdOx species over Pd/BaO/Al₂O₃, which inhibits the NO dissociation and thus drives the selectivity to N₂O in NO reduction.

Open image in new window