The leachability and chemical speciation of selected trace elements in fly ash from coal combustion and refuse incineration

A laboratory leaching test has been used to predict the potential mobility of As, Se, Pb and Cd in landfilled fly ash produced by coal combustion and refuse incineration. These waste residues also formed the basis of a speciation study in which the valency states of As and Se and the chemical forms of Pb and Cd have been determined. Selenium displayed the greatest leachability in each ash type, despite being present at relatively low concentrations in both materials. Substantial amounts of other trace elements were also leached, particularly Pb and Cd from refuse ash and As from coal ash. Chemical associations of Pb and Cd were examined by a sequential extraction procedure. In coal fly ash, both elements were mostly present in the residual fraction, while in refuse ash these elements were mainly associated with the exchangeable fraction. Water-soluble extracts of coal fly ash contained As exclusively as As(V); high background interference prevented the detection of water-soluble As in refuse ash. Selenium was present largely as Se(IV) in aqueous extracts of both ash types. The value of speciation techniques and leaching tests as predictors of environmental behaviour is discussed in conjunction with results of routine trace element determinations and plant uptake studies.     

Batch test assessment of waste-to-energy combustion residues impacts on precipitate formation in landfill leachate collection systems

Disposal practices for bottom ash and fly ash from waste-to-energy (WTE) facilities include emplacement in ash monofills or co-disposal with municipal solid waste (MSW) and residues from water and wastewater treatment facilities. In some cases, WTE residues are used as daily cover in landfills that receive MSW. A recurring problem in many landfills is the development of calcium-based precipitates in leachate collection systems. Although MSW contains varying levels of calcium, WTE residues and treatment plant sludges have the potential to contribute concentrated sources of leachable minerals into landfill leachates. This study was conducted to evaluate the leachability of calcium and other minerals from residues generated by WTE combustion using residues obtained from three WTE facilities in Florida (two mass-burn and one refuse-derived fuel). Leaching potential was quantified as a function of contact time and liquid-to-solid ratios with batch tests and longer-term leaching tests using laboratory lysimeters to simulate an ash monofill containing fly ash and bottom ash. The leachate generated as a result of these tests had total dissolved solid (TDS) levels ranging from 5 to 320 mg TDS/g ash. Calcium was a major contributor to the TDS values, contributing from 20 to 105 g calcium/kg ash. Fly ash was a major contributor of leachable calcium. Precipitate formation in leachates from WTE combustion residues could be induced by adding mineral acids or through gas dissolution (carbon dioxide or air). Stabilization of residual calcium in fly ashes that are landfilled and/or the use of less leachable neutralization reagents during processing of acidic gases from WTE facilities could help to decrease the calcium levels in leachates and help to prevent precipitate formation in leachate collection systems.     

Nickel speciation of residual oil fly ash and ambient particulate matter using X-ray absorption spectroscopy

The chemical speciation of Ni in fly ash produced from approximately 0.85 wt % S residual (no. 6 fuel) oils in laboratory (7 kW)- and utility (400 MW)-scale combustion systems was investigated using X-ray absorption fine structure (XAFS) spectroscopy, X-ray diffraction (XRD), and acetate extraction [1 M NaOAc-0.5 M HOAc (pH 5) at 25 degrees C]-anodic stripping voltammetry (ASV). XAFS was also used to determine the Ni speciation of ambient particulate matter (PM) sampled near the 400-MW system. Based on XAFS analyses of bulk fly ash and their corresponding acetate extraction residue, it is estimated that > 99% of the total Ni (0.38 wt %) in the experimentally produced fly ash occurs as NiSO4.xH2O, whereas > 95% of the total Ni (1.70 and 2.25 wt %) in two fly ash samples from the 400-MW system occurs as NiSO4.xH2O and Ni-bearing spinel, possibly NiFe2O4. Spinel was also detected using XRD. Acetate extracts most of the NiSO4.xH2O and concentrates insoluble NiFe2O4 in extraction residue. Similar to fly ash, ambient PM contains NiSO4.xH2O and NiFe2O4; however, the proportion of NiSO4.xH2O relative to NiFe2O4 is much greater in the PM. Results from this and previous investigations indicate that residual oil ash produced in the 7-kW combustion system lack insoluble Ni (e.g., NiFe2O4) but are enriched in soluble NiSO4.xH2O relative to fly ash from utility-scale systems. This difference in Ni speciation is most likely related to the lack of additive [e.g., Mg(OH)2] injection and residence time in the 7-kW combustion system.     

Arrested municipal solid waste incinerator fly ash as a source of heavy metals to the UK environment

Arrested fly ash samples from most currently operating municipal solid waste (MSW) incinerators in the UK have been analysed for a range of elements. Some of the more important heavy metals ranged in concentration as follows: Cd, 21-4646 (median = 271) mg kg(-1); Cu, 296-1307 (642) mg kg(-1); Cr, 44-1328 (574) mg kg(-1); Ni, 45-2204 (74) mg kg(-1); Pb, 447-9704 (4337) mg kg(-1); and Zn, 2285-13,500 (9232) mg kg(-1). These concentrations represent considerable enrichments relative to median UK soil concentrations. Enrichment ratios (defined as median fly ash: median UK soil) were as follows: Mn 1.6; Co 2.6; Ni 3.3; Ba 11; Sr 11; Cr 15; Cu 35; Pb 108; Zn 113; Cd 387. It is estimated that MSW incinerator ash contributes c. 15 t Cd and 241 t Pb to UK landfill sites per annum. These figures compare with previous studies by Hutton & Symon (Hutton, M. & Symon, C. (1986). The quantities of cadmium, lead, mercury and arsenic entering the UK environment from human activities. Sci. Total Environ., 57, 129-50.) which estimated that annual inputs to UK landfills from coal fly ash are c. 60 t Cd and 1270 t Pb. However, it is argued that metals associated with MSW ashes are potentially of greater environmental significance than in coal ashes, because they are much more available and present at much higher concentrations.     

Time-resolved leaching of cadmium and manganese from lignite and incinerator fly ash

Fly ashes from a lignite fired power plant and a municipal incinerator were leached for 3 hours using 0.1N HC1. Leachate was analyzed for Cd and Mn and plots of concentration versus time for these elements show Cd, a surface adsorbed element in the combustion process, to be rapidly removed from the ash particles in the initial four or five minutes of leaching. Manganese, a fly ash matrix element, is leached at a more constant rate as the ash praticles are dissolved. Total Cd and Mn concentrations in the incinerator fly ash are greater than total concentrations of these elements in the lignite fly ash.     

Cadmium uptake and translocation in tumbleweed (Salsola kali), a potential Cd-hyperaccumulator desert plant species: ICP/OES and XAS studies

Cadmium is a heavy metal, which, even at low concentrations, can be highly toxic to the growth and development of both plants and animals. Plant species vary extensively in their tolerance to excess cadmium in a growth medium and very few cadmium-tolerant species have been identified. In this study, tumbleweed plants (Salsola kali) grown in an agar-based medium with 20 mgl(-1) of Cd(II) did not show phytotoxicity, and their roots had the most biomass (4.5 mg) (P < 0.05) compared to the control plants (2.7 mg) as well as other treated plants. These plants accumulated 2696, 2075, and 2016 mg Cd kg(-1) of dry roots, stems, and leaves, respectively. The results suggest that there is no restricted cadmium movement in tumbleweed plants. In addition, the amount of Cd found in the dry leaf tissue suggests that tumbleweed could be considered as potential cadmium hyperaccumulating species. X-ray absorption spectroscopy studies demonstrated that in roots, cadmium was bound to oxygen while in stems and leaves, the metal was attached to oxygen and sulfur groups. This might imply that some small organic acids are responsible for Cd transport from roots to stems and leaves. In addition, it might be possible that the plant synthesizes phytochelatins in the stems, later coordinating the absorbed cadmium for transport and storage in cell structures. Thus, it is possible that in the leaves, Cd either exists as a Cd-phytochelatin complex or bound to cell wall structures. Current studies are being performed in order to elucidate the proposed hypothesis.     

Effect of applying chemical fertilizers on forms of lead and cadmium in red soil

A three-month incubation study was undertaken to examine the influence of N, P and K on the various forms (soluble plus exchangeable (SE), weakly specifically adsorbed (WSA), Fe-Mn oxides bound (OX), organic matter complexed (OM) and residual fractions (RES)) of lead (Pb) and cadmium (Cd) in a red soil. Application of urea at the rate of 200 mg N/kg significantly lowered the SE fraction, but raised the WSA or OX fraction of both metals. Supply of 80 mg P/kg caused a decrease in the SE fraction of the two metals. The WSA fraction of Pb was reduced, whereas that of Cd increased by adding P. However, addition of 100 mg K/kg led to an increase in the SE fraction, but a decrease in the WSA fraction of Pb and Cd. Applying chemical fertilizers had no significant consistent influences on the other fractions of metals. These findings suggest that in heavy metal contaminated red soil, applying fertilizers does not only provide plant nutrients, but may also change the speciations and thus biovailability of heavy metals.     

Nickel Speciation of Residual Oil Fly Ash and Ambient Particulate Matter Using X-ray Absorption Spectroscopy

ABSTRACT

The chemical speciation of Ni in fly ash produced from ~0.85 wt % S residual (no. 6 fuel) oils in laboratory (7 kW)- and utility (400 MW)-scale combustion systems was investigated using X-ray absorption fine structure (XAFS) spectroscopy, X-ray diffraction (XRD), and acetate extraction [1 M NaOAc-0.5 M HOAc (pH 5) at 25 °C]-anodic stripping voltammetry (ASV). XAFS was also used to determine the Ni speciation of ambient particulate matter (PM) sampled near the 400-MW system. Based on XAFS analyses of bulk fly ash and their corresponding acetate extraction residue, it is estimated that >99% of the total Ni (0.38 wt %) in the experimentally produced fly ash occurs as NiSO₄-xH₂O, whereas >95% of the total Ni (1.70 and 2.25 wt %) in two fly ash samples from the 400-MW system occurs as NiSO₄-xH₂O and Ni-bearing spinel, possibly NiFe₂O₄. Spinel was also detected using XRD. Acetate extracts most of the NiSO₄-xH₂O and concentrates insoluble NiFe₂O₄ in extraction residue. Similar to fly ash, ambient PM contains NiSO₄-xH₂O and NiFe₂O₄;

however, the proportion of NiSO₄-xH₂O relative to NiFe₂O₄ is much greater in the PM. Results from this and previous investigations indicate that residual oil ash produced in the 7-kW combustion system lack insoluble Ni (e.g., NiFe₂O₄) but are enriched in soluble NiSO₄-xH₂O relative to fly ash from utility-scale systems. This difference in Ni speciation is most likely related to the lack of additive [e.g., Mg(OH)₂] injection and residence time in the 7-kW combustion system.     

改性油页岩灰渣对水中镉离子的吸附性能

采用酸碱化改性方法对油页岩灰渣进行改性,确定最佳酸碱化方案,并研究了环境因素对改性油页岩灰渣吸附镉离子的影响。实验研究结果表明,油页岩灰渣经50%的HNO3和20%的NaOH处理时,对镉离子的吸附能力最强。在吸附温度为30℃,初始溶液pH为6～7条件下,0.6 g的改性油页岩灰渣对50 mg/L Cd2+溶液50 mL,吸附150 min时,其吸附率达到86%以上。在实验条件下,改性油页岩灰渣对Cd2+的吸附符合Langmuir和Freundlich等温吸附方程,相关系数分别为0.9626和0.9944,其对Cd2+的理论饱和吸附量达到7.91 mg/g。改性油页岩灰渣对Cd2+的吸附主要归因于离子交换和表面吸附作用。     

SGA对垃圾焚烧飞灰中重金属的固化性能研究

根据EPA1311、HJ／T299—2007、HJ／T300—2007和HJ557—2009等国内外不同标准,研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性,探讨了六硫代胍基甲酸（sixthioguanidineacid,SGA）、二甲基二硫代氨基甲酸盐（sodiumdimethyldithiocarbamate,SDD）和Ca（OH）2浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明,随着浸提液pH的降低,该厂焚烧飞灰中大部分金属元素的浸出量增大,焚烧飞灰浸出液中的cd、Ni、Ph和zn浓度分别超过国家危险废物鉴别标准（GB5085．3—2007）规定值的4．75倍、1．47倍、6．72倍和2．20倍,属于危险废弃物,必须进行稳定化处理。当固化剂SGA加入量为0．1mol／kg时,稳定化后的重金属浸出浓度已经低于危险废物鉴别标准,且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）2;当固化剂SGA、SDD和Ca（OH）2加入量为0．5mol／kg时,稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB5085．3-2007）中的规定值。与SDD和Ca（OH）：相比,SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

Heavy metal leaching from coal fly ash amended container substrates during Syngonium production

Coal fly ash has been proposed to be an alternative to lime amendment and a nutrient source of container substrates for ornamental plant production. A great concern over this proposed beneficial use, however, is the potential contamination of surface and ground water by heavy metals. In this study, three fly ashes collected from Florida, Michigan, and North Carolina and a commercial dolomite were amended in a basal substrate. The formulated substrates were used to produce Syngonium podophyllum Schott 'Berry Allusion' in 15-cm diameter containers in a shaded greenhouse. Leachates from the containers were collected during the entire six months of plant production and analyzed for heavy metal concentrations. There were no detectable As, Cr, Hg, Pb, and Se in the leachates; Cd and Mo were only detected in few leachate samples. The metals constantly detected were Cu, Mn, Ni, and Zn. The total amounts of Cu, Mn, Ni, and Zn leached during the six-month production period were 95, 210, 44, and 337 microg per container, indicating that such amounts in leachates may contribute little to contamination of surface and ground water. In addition, plant growth indices and fresh and dry weights of S. podophyllum 'Berry Allusion' produced from fly ash and dolomite-amended substrates were comparable except for the plants produced from the substrate amended with fly ash collected from Michigan which had reduced growth indices and fresh and dry weights. Thus, selected fly ashes can be alternatives to commercial dolomites as amendments to container substrates for ornamental plant production. The use of fly ashes as container substrate amendments should represent a new market for the beneficial use of this coal combustion byproduct.     

Long-term increased bioaccumulation of mercury in largemouth bass follows reduction of waterborne selenium

Average mercury concentrations in largemouth bass from Rogers Quarry in east Tennessee were found to increase steadily following the elimination of selenium-rich discharges of fly ash to the quarry in 1989. From 1990 to 1998, mean mercury concentrations (adjusted to compensate for the covariance between individual fish weight and mercury concentration) in bass rose from 0.02 to 0.61 mg/kg. There was no indication that the rate increase was slowing or that mercury concentrations in fish were approaching a plateau or steady state. Mean selenium concentrations in bass declined from 3 to 1 mg/kg over the first five years of the study, but remained at 1-1.5 mg/kg (about twice typical concentrations in bass from local reference sites) for the last three years of the study. Gross physical abnormalities were common in fish from the site in the first three years after elimination of fly ash discharges but disappeared after two more years. Although it remains possible that other chemical or physical changes related to fly ash disposal in the system were associated with increased mercury bioaccumulation, the most likely explanation is that selenium played a critical role. It appears as though aqueous selenium enrichment was capable of having a profound effect on mercury bioaccumulation in this system but at the cost of causing a high incidence of gross abnormalities in fish. However, it is possible that selenium concentrations between the national ambient water quality criterion for the protection of aquatic life, 5 microg/l, and that now found in Rogers Quarry (<2 microg/l) could reduce mercury bioaccumulation without causing adverse effects on aquatic biota and fish-eating wildlife.     

Air-surface exchange of mercury with soils amended with ash materials

Air-surface exchange of mercury (Hg) was measured from soil low in Hg (0.013 mg/kg) amended with four different ash materials: a wood ash containing -10% coal ash (0.070 mg/kg Hg), a mixture of two subbituminous coal fly ashes (0.075 mg/kg Hg), a subbituminous coal ash containing -10% petroleum coke ash (1.2 mg/kg Hg), and an ash from incinerated municipal sewage sludge (4.3 mg/kg Hg) using a dynamic flux chamber. Ash was added to soil to simulate agricultural supplements, soil stabilization, and pad layers used in livestock areas. For the agricultural amendment, -0.4% ash was well mixed into the soil. To make the stabilized soil that could be used for construction purposes, -20% ash was mixed into soil with water. The pad layer consisted of a wetted 1-cm layer of ash material on the soil surface. Diel trends of Hg flux were observed for all of the substrates with significantly higher Hg emissions during the day and negligible flux or deposition of Hg during the night. Hg fluxes, which were measured in the summer months, were best correlated with solar radiation, temperature, and air O3 concentrations. Mean Hg fluxes measured outdoors for unamended soils ranged from 19 to 140 ng/m2 day, whereas those for soil amended with ash to simulate an agricultural application ranged from 7.2 to 230 ng/m2 day. Fluxes for soil stabilized with ash ranged from 77 to 530 ng/m2 day and for soil with pads constructed of ash ranged from -50 to 90 ng/m2 day. Simple analytical tests (i.e., total Hg content, synthetic precipitation leaching procedure, heating, and indoor gas-exchange experiments) were performed to assess whether algorithms based on these tests could be used to predict Hg fluxes observed outdoors using the flux chamber. Based on this study, no consistent relationships could be developed. More work is needed to assess long-term and seasonal variations in Hg flux from (intact and disturbed) substrates before annual estimates of emissions can be developed.     

Impacts of pH and ammonia on the leaching of Cu(II) and Cd(II) from coal fly ash

Many coal-fired power plants are implementing ammonia-based technologies to reduce NO(x) emissions. Excess ammonia in the flue gas often deposits on the coal fly ash. Ammonia can form complexes with many heavy metals and change the leaching characteristics of these metals. This research tends to develop a fundamental understanding of the ammonia impact on the leaching of some heavy metals, exemplified by Cu(II) and Cd(II), under different pH conditions. Batch results indicated that the adsorption is the main mechanism controlling Cu(II) and Cd(II) leaching, and high concentrations of ammonia (>5,000 mg/l) can increase the release of Cu(II) and Cd(II) in the alkaline pH range. Based on the chemical reactions among fly ash, ammonia, and heavy metal ion, a mathematical model was developed to quantify effects of pH and ammonia on metal adsorption. The adsorption constants (logK) of Cu(2+), Cu(OH)(+), Cu(OH)(2), and Cu(NH(3))(m)(2+) for the fly ash under investigation were respectively 6.0, 7.7, 9.6, and 2.9. For Cd(II), these constants were respectively 4.3, 6.9, 8.8, and 2.6. Metal speciation calculations indicated that the formation of less adsorbable metal-ammonia complexes decreased metal adsorption, therefore enhanced metal leaching.     

SGA对垃圾焚烧飞灰中重金属的固化性能研究简

根据EPA 1311、HJ/T 299-2007、HJ/T 300-2007和HJ 557-2009等国内外不同标准,研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性,探讨了六硫代胍基甲酸（sixthio guanidine acid,SGA）、二甲基二硫代氨基甲酸盐（sodium dimethyl dithio carbamate,SDD）和Ca（OH）₂浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明,随着浸提液pH的降低,该厂焚烧飞灰中大部分金属元素的浸出量增大,焚烧飞灰浸出液中的Cd、Ni、Pb和Zn浓度分别超过国家危险废物鉴别标准（GB5085.3-2007）规定值的4.75倍、1.47倍、6.72倍和2.20倍,属于危险废弃物,必须进行稳定化处理。当固化剂SGA加入量为0.1 mol/kg时,稳定化后的重金属浸出浓度已经低于危险废物鉴别标准,且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）₂;当固化剂SGA、SDD和Ca（OH）₂加入量为0.5 mol/kg时,稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB 5085.3-2007）中的规定值。与SDD和Ca（OH）₂相比,SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

Characterization and spatial distribution of heavy metals in sediment from Cedar and Ortega rivers subbasin

The Cedar and Ortega rivers subbasin is a complex environment where both natural and anthropogenic processes influence the characteristics and distributions of sediments and contaminants, which in turn is of importance for maintenance, dredging and pollution control. This study investigated the characteristics and spatial distribution of heavy metals, including lead (Pb), copper (Cu), zinc (Zn) and cadmium (Cd), from sediments in the subbasin using field measurements and three-dimensional kriging estimates. Sediment samples collected from three sampling depth intervals (i.e., 0-0.10, 0.11-0.56 and 0.57-1.88 m) in 58 locations showed that concentrations of Pb ranged from 4.47 to 420.00 mg/kg dry weight, Cu from 2.30 to 107.00 mg/kg dry weight, Zn from 9.75 to 2,050.00 mg/kg dry weight and Cd from 0.07 to 3.83 mg/kg dry weight. Kriging estimates showed that Pb, Cu and Cd concentrations decreased significantly from the sediment depth of 0.10 to 1.5 m, whereas Zn concentrations were still enriched at 1.5 m. It further revealed that the Cedar River area was a potential source area since it was more contaminated than the rest of the subbasin. Comparison of aluminum (Al)-normalized metal concentrations indicated that most of the metals within the top two intervals (0-0.56 m) had concentrations exceeding the background levels by factors of 2-10. A three-dimensional view of the metal contamination plumes showed that all of the heavy metals, with concentrations exceeding the threshold effect level (TEL) that could pose a threat to the health of aquatic organisms, were primarily located above the sediment depth of 1.5 m.     

Air-Surface Exchange of Mercury with Soils Amended with Ash Materials

Abstract

Air-surface exchange of mercury (Hg) was measured from soil low in Hg (0.013 mg/kg) amended with four different ash materials: a wood ash containing ～10% coal ash (0.070 mg/kg Hg), a mixture of two subbituminous coal fly ashes (0.075 mg/kg Hg), a subbituminous coal ash containing ～10% petroleum coke ash (1.2 mg/kg Hg), and an ash from incinerated municipal sewage sludge (4.3 mg/kg Hg) using a dynamic flux chamber. Ash was added to soil to simulate agricultural supplements, soil stabilization, and pad layers used in livestock areas. For the agricultural amendment, ～0.4% ash was well mixed into the soil. To make the stabilized soil that could be used for construction purposes, ～20% ash was mixed into soil with water. The pad layer consisted of a wetted 1-cm layer of ash material on the soil surface. Diel trends of Hg flux were observed for all of the substrates with significantly higher Hg emissions during the day and negligible flux or deposition of Hg during the night. Hg fluxes, which were measured in the summer months, were best correlated with solar radiation, temperature, and air O₃ concentrations. Mean Hg fluxes measured outdoors for unamended soils ranged from 19 to 140 ng/m² day, whereas those for soil amended with ash to simulate an agricultural application ranged from 7.2 to 230 ng/m² day. Fluxes for soil stabilized with ash ranged from 77 to 530 ng/m² day and for soil with pads constructed of ash ranged from ?50 to 90 ng/m² day. Simple analytical tests (i.e., total Hg content, synthetic precipitation leaching procedure, heating, and indoor gas-exchange experiments) were performed to assess whether algorithms based on these tests could be used to predict Hg fluxes observed outdoors using the flux chamber. Based on this study, no consistent relationships could be developed. More work is needed to assess long-term and seasonal variations in Hg flux from (intact and disturbed) substrates before annual estimates of emissions can be developed.     

Determination of polychlorinated dibenzo-p-dioxins and dibenzo-furans in solid residues from wood combustion by HRGC/HRMS

PCDD/PCDF were determined in solid samples from wood combustion. The samples included grate ashes, bottom ashes, furnace ashes as well as fly and cyclone ashes. The solid waste samples were classified into bottom and fly ash from native wood and bottom and fly ash from waste wood. For each of the four classes concentration distribution patterns from individual congeners, the sums of PCDD/PCDF and the international toxicity equivalents (I-TEQ) values are given. The I-TEQ levels of fly ash from waste wood burning can be approximately up to two thousand times higher than the values from fly ashes of natural wood. The I-TEQ levels in bottom ashes from waste wood combustion systems are as low as the corresponding ashes from the combustion of native wood. Grate ash samples from waste wood combustion systems with low carbon burnout show high levels of PCDD/PCDF.     

Effect of clay and organic matter type on the ecotoxicity of zinc and cadmium to the potworm Enchytraeus albidus

Clay and organic matter are considered as important parameters influencing bioavailability and ecotoxicity of metals in soils. As there exists a large variation in the type of clay and organic matter in field soils, the quantity of these variables alone may not be good indicators of metal bioavailability. To test this hypothesis, toxicity experiments with the potworm Enchytraeus albidus were conducted in artificial soils with three types of clay and seven types of organic matter, while the soil pH was kept constant. The 14d LC₅₀ of zinc and cadmium varied from 83.0 to 1140 mg Zn/kg D.W. and from 55.2 to 704 mg Cd/kg D.W., respectively, depending on the type of clay and organic matter that were used. Simultaneous measurements of the cation exchange capacity showed that this soil parameter is a better indicator of the bioavailability as it takes into account the type of clay and organic matter as well as other adsorption phases such as metal oxyhydroxides.     

Recombinant luminescent bacterial sensors for the measurement of bioavailability of cadmium and lead in soils polluted by metal smelters

Environmental hazard of heavy metals in soils depends to a large extent on their bioavailability. The approach used in this study enables the determination of bioavailable metals in solid-phase samples. Two recombinant bacterial sensors, one responding specifically to cadmium and the other to lead and cadmium by increase of luminescence (firefly luciferase was used as a reporter) were used to determine the bioavailability of these metals in soil-water suspensions (a contact assay) and respective particle-free extracts. Fifty agricultural soils sampled near zinc and lead smelters in the Northern France containing up to (mg/kg) 20.1 of Cd, 1050 of Pb and 1390 of Zn were analysed. As the soil matrix interferes with the assay, recombinant luminescent control bacteria lacking the metal recognizing protein and corresponding promoter (thus, being not metal-inducible) but otherwise comparable to the sensor bacteria (the same host bacterium and plasmid encoding luciferase) were used in parallel to take into account the possible quenching and/or stimulating effects of the sample on the luminescence of the sensor bacteria. Both, chemical and sensor analysis showed that only microg/l levels of metals were extracted from the soil into the water phase (0.1% of the total Cd, 0.07% of Pb and 0.5% of Zn). However, 115-fold more Cd and 40-fold more Pb proved bioavailable if the sensor bacteria were incubated in soil suspensions (i.e., in the contact assay). The bioavailability of metals in different soils varied (depending probably on soil type) ranging from 0.5% to 56% for cadmium and from 0.2% to 8.6% for lead.