碱激发粉煤灰对Cs~+的吸附行为

将粉煤灰进行碱激发改性,运用XRD和SEM技术对碱激发粉煤灰进行了表征,通过静态平衡吸附实验研究了碱激发粉煤灰对Cs+的吸附动力学和热力学特性,并对吸附前后的碱激发粉煤灰进行了FTIR分析。表征结果显示,碱激发处理后,粉煤灰的晶相发生了改变,且粉煤灰表面密实的硬壳层被破坏。实验结果表明:在初始Cs+质量浓度为200 mg/L、吸附温度为25℃、溶液pH为10、碱激发粉煤灰投加量为12.0 g/L的条件下,碱激发粉煤灰对Cs+的平衡吸附率可达80%以上,其吸附能力比碱激发前提高了3倍以上;吸附过程可用准二阶动力学方程来描述,并较好地符合Langmuir等温吸附模型;碱激发粉煤灰对Cs+的吸附是吸热过程,且能自发进行;该过程以物理吸附为主,并伴随化学吸附。     

碱熔融—微波晶化法合成粉煤灰沸石及其对Cd2+的吸附

以粉煤灰为主要原料,采用碱熔融—微波晶化法合成粉煤灰沸石。采用XRD,SEM,TEM等技术表征了粉煤灰沸石的微观结构,并对其吸附Cd²⁺的性能进行了研究。表征结果显示,粉煤灰沸石主要由X型沸石、P型沸石和铝组成,粉煤灰沸石中有排列规则、呈蜂窝状的孔穴和孔道存在,其孔穴和孔道大小分布均匀,致密。粉煤灰沸石的比表面积为108.49 m²/g,平均孔径为3.779 nm,孔体积为0.221 mL/g。实验结果表明,在溶液pH为7、吸附时间30 min的最佳吸附条件下,Cd²⁺去除率均大于94%。粉煤灰沸石对Cd²⁺的吸附可很好地用二级动力学方程进行拟合,相关系数为0.999 99。可用Langmuir等温吸附模型描述该吸附过程,该吸附过程是单分子层吸附,主要是化学吸附,粉煤灰沸石对Cd²⁺的饱和吸附量为49.261 mg/g。     

粉煤灰及其制备沸石对高浓度氨氮的去除比较

以粉煤灰为原料,采用改进的水热合成法制备了粉煤灰沸石,并将粉煤灰和粉煤灰沸石用于高浓度氨氮的吸附去除。实验结果表明:在粉煤灰和粉煤灰沸石的投加量分别为0.10 g/m L和0.04 g/m L、反应体系p H为5~7、初始氨氮质量浓度为500 mg/L的条件下,分别吸附660 min和60 min,粉煤灰和粉煤灰沸石对氨氮的去除率分别约为20.1%和50.7%左右,粉煤灰沸石对高浓度氨氮的去除效果明显优于粉煤灰;粉煤灰和粉煤灰沸石对氨氮的吸附动力学行为符合准二级动力学方程;Langmuir和Freundlich等温吸附模型能较好地描述粉煤灰对氨氮的等温吸附过程,而粉煤灰沸石对氨氮的等温吸附过程则更适宜用线性模型和Freundlich模型描述。     

碱熔融-微波晶化法合成粉煤灰沸石及其对Cd~(2+)的吸附

以粉煤灰为主要原料,采用碱熔融—微波晶化法合成粉煤灰沸石。采用XRD,SEM,TEM等技术表征了粉煤灰沸石的微观结构,并对其吸附Cd~(2+)的性能进行了研究。表征结果显示,粉煤灰沸石主要由X型沸石、P型沸石和铝组成,粉煤灰沸石中有排列规则、呈蜂窝状的孔穴和孔道存在,其孔穴和孔道大小分布均匀,致密。粉煤灰沸石的比表面积为108.49 m2/g,平均孔径为3.779 nnm,孔体积为0.221 mL/g。实验结果表明,在溶液pH为7、吸附时间30 min的最佳吸附条件下,Cd~(2+)去除率均大于94%。粉煤灰沸石对Cd~(2+)的吸附可很好地用二级动力学方程进行拟合,相关系数为0.999 99。可用Langmuir等温吸附模型描述该吸附过程,该吸附过程是单分子层吸附,主要是化学吸附,粉煤灰沸石对Cd~(2+)的饱和吸附量为49.261 mg/g。     

熔融-水热法合成粉煤灰沸石及其吸附性能研究

以粉煤灰为原料,研究了在熔融温度分别为 300 ℃、 400 ℃、 500 ℃,熔融时间分别为 1 h、 2 h、 3 h,水热温度分别为 45 ℃、 65 ℃、 85 ℃,水热时间分别为 6 h、 8 h、 10 h,对合成粉煤灰沸石( FZ)吸附性能的影响.结果表明熔融温度为 300 ℃,熔融保温时间为 1 h,水热温度为 65 ℃,水热保温时间为 6 h,产物中有类沸石生成.熔融-水热合成 FZ对 Cd2+吸附率为 99.82%,吸附量为 0.199 64 mg/g,略高于活性炭(吸附率 99.69%)优于天然沸石(吸附率 97.94%).     

固硫灰固化焦化废水处理外排污泥

采用机械力化学法活化循环流化床燃煤固硫灰,用于固化焦化废水处理外排污泥(CWT污泥)。探讨了固硫灰活化条件,并通过XRD和FTIR分析了固硫灰固化CWT污泥中重金属的机理。实验结果表明:当m(Ca O)∶m(Ca O+固硫灰)为20%、球磨频率为40 Hz、球磨时间为2 h时,养护28 d固硫灰固化体的平均抗压强度达到72.2 MPa;当污泥掺加量为50%(w)时,养护28 d含污泥固化体的抗压强度达到8.5 MPa,固化体浸出液中Pb2+和As5+的质量浓度分别为0.177 mg/L和0.013 mg/L,均远低于GB 5085.3—2007《危险废物鉴别标准浸出毒性鉴别》的规定限值。XRD和FTIR表征结果表明,在固硫灰活化过程中,混合体系水化生成了C—S—H凝胶、斜方钙沸石和钙矾石,可通过物理包裹、吸附及离子交换的形式实现CWT污泥中Pb2+和As5+的固化/稳定化。     

粉煤灰两步水热法制备人工沸石

以粉煤灰为原料,采用两步水热法制备人工沸石。SEM、XRD、X射线荧光光谱分析结果表明:制得的人工沸石纯度较高,主要为Na-A型沸石和少量13X型沸石,主要化学成分为SiO2和Al2O3。说明采用两步法制备人工沸石克服了传统水热法杂质含量高的缺陷。采用人工沸石处理初始Mn2+质量浓度为50.00mg/L的模拟含锰废水,吸附125min后,Mn2+去除率达98.19%,模拟废水中剩余Mn2+质量浓度为0.90mg/L。     

粉煤灰的改性及对刚果红的吸附

分别采用沸水浸泡、酸浸、碱浸和加热的方法对粉煤灰进行改性处理,利用FTIR仪和XRD仪对改性粉煤灰的成分和官能团进行了分析,并利用改性粉煤灰对模拟刚果红废水进行脱色。实验结果表明：碱改性粉煤灰中含有大量官能团,以及NaPl型沸石类物质,能够明显提高粉煤灰对刚果红的吸附性能;与活性炭相比,碱改性粉煤灰具有更高的性价比;在初始刚果红质量浓度为20mg/L、碱改性粉煤灰加入量为50g/L的条件下,废水的脱色率可达87.52%;碱改性粉煤灰对刚果红的吸附过程遵循二级反应动力学,较好地符合Langmuir等温式和Freundlich等温式。     

粉煤灰基沸石分子筛对水中氨氮的吸附

以粉煤灰为原料,采用碱熔融-水热法制备了3种沸石分子筛,运用XRD、XRF、SEM和BET等手段进行了表征,并将分子筛用于吸附溶液中的氨氮,考察了影响氨氮吸附效果的主要因素、氨氮等温吸附特征和吸附动力学特征。结果表明：分子筛B(Na_20.8Al₂₃Si₃₆O₁₁₇·7.69 H₂O)对氨氮的吸附效果最佳,在初始氨氮质量浓度100 mg/L、分子筛B加入量2 g/L、初始溶液pH 7、吸附温度25℃、转速150 r/min的条件下,吸附60 min后,氨氮吸附量和去除率分别为40.61 mg/g和90%;4种阳离子对氨氮吸附效果的影响顺序依次为K⁺>Ca²⁺>Na⁺>Mg²⁺;分子筛B对氨氮的吸附为单分子层吸附,具有化学吸附的特征;分子筛B吸附氨氮的的最佳工艺条件为初始溶液pH 7、吸附温度45℃、初始氨氮质量浓度40 mg/L,在该条件下,氨氮去除率为93%。     

粉煤灰的改性及其吸附性能

以改性粉煤灰为吸附剂,对亚甲基蓝溶液进行吸附实验。经正交实验确定改性粉煤灰的最佳制备条件:煅烧温度为850℃,粉煤灰与ZnCl2的质量比为2∶2,盐酸加入量为2.4mol/L,粉煤灰粒径为16.8mm。在亚甲基蓝溶液初始质量浓度为10mg/L、改性粉煤灰加入量为200mg/L、振荡时间为3.0h、溶液pH为5、吸附温度为25℃的条件下,亚甲基蓝的降解率和溶液脱色率分别达86.24%和82.76%。     

Strength, leachability and microstructure characterisation of Na2SiO3-activated ground granulated blast-furnace slag solidified MSWI fly ash.

The chemical composition and the leachability of heavy metals in municipal solid waste incinerator (MSWI) fly ash were measured and analysed. For the leachability of unstabilized MSWI fly ash it was found that the concentrations of Pb and Cr exceeded the leaching toxicity standard. Cementitious solidification of the MSWI fly ash by Na2SiO3-activated ground granulated blast-furnace slag (NS) was investigated. Results show that all solidified MSWI fly ash can meet the landfill standards after 28 days of curing. The heavy metals were immobilized within the hydration products such as C-S-H gel and ettringite through physical encapsulation, substitution, precipitation or adsorption mechanisms.     

复合改性粉煤灰对磷的吸附性能

将粉煤灰（FA）与Na₂CO₃混合焙烧后浸渍负载Fe²⁺,制备了复合改性粉煤灰（CMFA）。通过多种手段对CMFA进行了表征,并将其用于含磷废水的吸附处理。表征结果显示：改性后的粉煤灰表面疏松多孔,比表面积增大了21倍,产生了金属盐类熔出物及羟基氧化铁和羟基官能团。实验结果表明：当初始磷质量浓度为50 mg/L、吸附温度为20 ℃、溶液pH为4.3、CMFA投加量为5 g/L、吸附时间为30 min时,磷去除率可达98.01%,较FA的50.10%大幅提升;20 ℃时,CMFA对磷的饱和吸附量可达22.15 mg/g;用拟二级动力学模型可较准确地描述CMFA对磷的吸附过程,该过程为自发的吸热过程,符合Langmuir等温吸附模型,为以离子交换为主的化学吸附。     

Lead immobilization in mechanochemical fly ash recycling

In previous studies, we focused on a mechanochemical process for recycling fly ash for use in cement; this process was expected to immobilize heavy metals in the fly ash, a desirable outcome in light of the fact that recycled fly ash is commonly used in the synthesis of inorganic materials. Here, we investigated the leaching of lead (Pb) from fly ash treated by a mechanochemical process and from cement prepared from the treated fly ash. We used lead oxide (PbO), a typical Pb compound in fly ash, as a model substance. Mechanochemical treatment of the fly ash inhibited Pb leaching by 93%, and further inhibition (more than 99.9%) was observed in cement produced from the treated fly ash. During the mechanochemical treatment, PbO was reduced to Pb by iron from the stainless-steel mill used for processing, and the lower solubility of Pb in water resulted in immobilization of the Pb.     

Synthesis of zeolite from waste fly ash for adsorption of CO2

Zeolitic sorbents for CO₂ adsorption were prepared from waste coal fly ash (FA) through hydrothermal treatment at various ratios of NaOH/FA and NaAlO₂/FA, including an initial alkali fusion step. The fusion step decomposed the fly ash into very small amorphous particulate zeolite forms. The fly ash was converted to Na-P1 type with a NaOH/FA ratio of 0.5 and Na-A type with a NaAlO₂/FA ratio of 0.53. The product properties were affected by the reaction temperature: Na-P1 and Na-A types were formed at 100°C. Temperatures above 140°C led to the formation of more sodalite because of the redissolving and recrystallization of zeolite crystals. Alkali metal and alkaline earth metal cations were impregnated in the synthesized Na-P1 and Na-A zeolite through an ion-exchange method. The completed zeolitic sorbents were applied to the adsorption of low-level CO₂. As a result of the experiments, calcium ions were found to be the best for CO₂ adsorption owing to their electrostatic behavior and acid-base interaction.     

Environmental impact of fly ash utilization in roadway embankments

The leaching potential of heavy metals from a roadway embankment constructed of fly ash and soil mixture was studied. Leaching of eight environmentally concerned metals Ag, As, Ba, Cd, Cr, Hg, Pb, and Se from the fly ash–soil mixtures was examined through batch leaching test and column leaching test. The batch leaching test results showed that the fly ash meets the local regulatory standards for beneficial use of nonhazardous wastes. The column leach test revealed that only Ba, Cr, and Se were detectable in the effluents. The peak concentration of Ba in the effluents was much lower than the US EPA Primary Drinking Water Regulations’ maximum contaminant level (MCL). The peak concentrations of Cr and Se exceeded the MCLs only in the initial flush stage and quickly decreased to below the MCLs. Results of this study suggest a great potential for fly ash to be used in roadway embankments to enhance their mechanical properties, reduce the use of soil, and avoid the disposal of fly ash as waste.     

Quantifying the availability and the stability of trace cationic elements in fly ash

For adsorption-desorption controlled leaching processes, the total leachable mass and the adsorption constant are parameters representing the availability and the stability of trace elements in solid media. With these parameters, one can predict the leaching behavior of trace elements from solids under various pH and solid-to-liquid ratio conditions. An approach was developed in this paper to determine these parameters for model elements Cu(II), Cd(II), and Ni(II) in fly ash. This approach consists of a batch equilibrium titration, a batch equilibrium leaching with and without target element addition, and mathematical modeling. Results indicated that the adsorption constant of a trace element can be determined by modeling the adsorption ratio of the added element to the system as a function of pH. Results also indicated that the trace element originally present in fly ash had similar adsorption-desorption behavior as that added externally. By modeling the batch leaching data with and without external element addition, the total leachable mass and adsorption constant of the target element can be determined simultaneously. The total leachable mass is in agreement with experimental data from 50mM EDTA extraction.