COD快速测定法

以用时30min的半微量密闭微波消解法取代COD国标测定中的重铬酸钾回流法,改进后的方法精密度小于5．15％,准确度达到102％,COD测定下限为51mg／L。该法节省时间、取样量少、成本低,适用于大批量水样的快速测定。     

混凝-催化氧化法预处理氨基C酸生产废水

采用混凝-催化氧化组合工艺预处理氨基C酸生产废水,考察了混凝剂加入量、废水pH、氧化剂加入量、反应时间和催化剂的重复使用次数等因素对废水处理效果的影响。混凝-催化氧化法预处理氨基C酸生产废水的最佳工艺条件为：质量分数为10％的FeSO4溶液作混凝剂,加入量为250InL／L;质量分数为1％的ClO2溶液作氧化剂,加入量为75mL／L;Ni／AC作催化剂,加入量为40g/L;废水pH为3．2;催化氧化反应时间为60min。在该条件下,废水的COD去除率可达78．4％,BOD,／COD由原来的0．076提高到0．292,可生化性得到明显改善。Ni／AC催化剂连续使用7次后仍保持稳定的催化活性。经济性初步分析表明,1t废水的处理成本约为16元。     

用MnSO4作催化剂测定废水中的COD

介绍了用MnSO4代替Ag2SO4作催化剂定废水中COD的方法。该方法可降低分析成本,且使回流时间缩短为30min,方法的变异系数、回收率分别为0．65％和96．8％－100．8％。     

流动注射-氢化物发生-原子吸收法测定土壤中微量砷

用混酸消解土壤试样，用体积分数为20％的盐酸作酸介质，质量分数为1．5％的硼氢化钾作还原剂，体积分数为1％的盐酸作载液，采用流动注射-氢化物发生三-原子吸收法定量测定土壤中的微劈砷。通过实验确定，在原子化温度为920℃、土壤中共存元素含量低于5mg／kg时对测定无干扰。该方法的榆出限为0．5μg/L，线性范嘲为5～100μg/L．相对标准偏差为0．89％，平均回收率达98．99％：     

催化湿式氧化法处理吡虫啉农药废水

自制了Cu／Mn，Cu／Ce，Cu／Ni，Ce／Mn，Ce／Ag等催化剂，经过性能比较，选择催化活性较高且金属溶出量较小的Cu／Ni作催化剂。用催化湿式氧化法处理吡虫啉农药废水，考察了各种因素对处理效果的影响。实验结果表明：在进水pH为6．93、Cu／Ni加入量为4．0g、反应温度为190oC、氧分压为1．6MPa、反应时间为120min的条件下，COD去除率为95％；处理后废水的BOD5／COD从0．093增至0．590，可生化性明显改善。     

催化臭氧氧化法处理甲醛废水

用异丙醇钛盐表面改性法制备TiO2／SiO2催化剂，对甲醛废水进行催化臭氧氧化处理。通过比表面积的BET测定法、X射线衍射和拉曼光谱等分析方法对TiO2／SiO2催化剂进行了表征，考察了TiO2／SiO2催化剂加入量、臭氧流量及溶液pH等因素对甲醛催化臭氧氧化效果的影响。实验结果表明，在SiO2表面，TiO2微晶粒子以锐钛矿型高度分散；在甲醛质量浓度700mg／L、COD1000mg／L、TiO2／SiO2催化剂加入量2．0g、臭氧流量2．5mg／min、溶液pH8．5的条件下，催化臭氧氧化反应30min后，甲醛质量浓度由700mg／L降至39mg／L，COD去除率认到87．5％．     

重铬酸钾改进法测定合成氨厂废水中的化学耗氧量

本法为测定废水中COD的重铬酸钾改进法,它与标准方法相比,以不使用硫酸汞来消除氯离子的干扰和不使用硫酸银作催化剂为特点,可避免汞的二次污染、节约贵金属试剂,且装置简单,操作方便。实验证明本法的准确度和精密度与标准法相近。每个样品的回流时间由两小时减为45分鐘,每次测定费用降低0.57元。大量实测证明,本法是可行的。     

氢化物发生-原子荧光法同时测定污水中的砷和硒

用HNO3-HClO4消解液消解水样,断续流动进样,在KBH4-酸体系中,采用氢化物发生-原子荧光法同时测定污水中的砷和硒。在含浓盐酸2．0mL的介质中加入硫脲-抗坏血酸溶液5mL,在温度高于15℃时放置30min后,以15g/L KBH4溶液为还原剂,5％(体积分数)HCl为载流测定砷、硒荧光强度。在最佳实验条件下,砷、硒的相对标准偏差分别小于4％和2％,检出限分别为0．89μg／L和0．51μg／L,加标回收率分别为91．5％～101．2％和94．0％～100．5％。该方法精密度高、测定结果稳定,达到环境监测要求。     

活性炭/H2O2催化氧化-絮凝法预处理化工有机废水

用活性炭作催化剂、H2O2作氧化剂催化氧化预处理高浓度化工有机废水,考察了各种因素对COD去除率的影响。实验结果表明,在H2O2加入量为0．8mL／L、活性炭与H2O2质量比为0．7、废水pH为4的条件下,反应120min后,调废水pH至8,加入絮凝剂聚合氯化铝进行絮凝沉淀,废水COD去除率达70％以上,色度去除率达80％以上。通过色谱-质谱仪对处理前后废水中的有机物进行分析,初步探讨了活性炭／H2O2催化氧化-絮凝法预处理化工有机废水的作用机理。     

高浓度难降解有机物废水的处理方法

高浓度难降解有机物废水（COD为3000～200000mg／L）在间歇式微波反应器内（温度为110～200℃，压力为0．3～1．6MPa）进行催化氧化，用氧气或空气作主要氧化剂，用经过水中浮选且能漂浮在液体表面上的活性炭作催化剂（加入量为废水质量的4％～30％）。当废水COD小于10000mg／L时，采用一次性处理；当废水COD为10000～200000mg／L时，     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

Bioassessment of silvicultural impacts in streams and wetlands of the Eastern United States

Bioassessment is a useful tool to determine the impact of logging practices on the biological integrity of streams and wetlands. Measuring biota directly has an intuitive appeal for impact assessment, and biota can be superior indicators to physical or chemical characteristics because they can reflect cumulative impacts over time. Logging can affect stream and wetland biota by increasing sedimentation rates, altering hydrologic, thermal, and chemical regimes, and changing the base of food webs. Biotic impacts of logging on streams compared to wetlands probably differ, and in this paper we review some of those differences. In streams, invertebrates, fishes, amphibians, algae, and macrophytes have been used as indicators of logging impacts. In wetlands, bioassessment is just beginning to be used, and plants and birds are the most promising indicator taxa. Various best management practices (BMPs) have been developed to reduce the impacts of logging on stream and wetland biota, and we review quantitative studies that have evaluated the efficacy of some of these techniques in streams and wetlands in the eastern United States. Remarkably few studies that address the overall efficacy of BMPs in limiting biotic changes in streams and wetlands after BMP implementation have been published in scientific journals, although some work exists in reports or is unpublished. We review these works, and compile conclusions about BMP efficacy for biota from this body of research.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Solubility and Potential Mobility of Heavy Metals in Two Contaminated Urban Soils from Stockholm,Sweden

The solubility and potential mobility of heavy metals (Cd, Cu,Hg, Pb and Zn) in two urban soils were studied by sequential andleaching extractions (rainwater). Compared to rural (arable) soils on similar parent material, the urban soils were highlycontaminated with Hg and Pb and to a lesser extent also with Cd,Cu and Zn. Metal concentrations in rainwater leachates were related to sequential extractions and metal levels reported fromStockholm groundwater. Cadmium and Zn in the soils were mainly recovered in easily extractable fractions, whereas Cu and Pb were complex bound. Concentrations of Pb in the residual fractionwere between two- and eightfold those in arable soils, indicatingthat the sequential extraction scheme did not reflect the solidphases affected by anthropogenic inputs. Cadmium and Zn conc. inthe rainwater leachates were within the range detected in Stockholm groundwater, while Cu and Pb conc. were higher, whichsuggests that Cu and Pb released from the surface soil were immobilised in deeper soil layers. In a soil highly contaminatedwith Hg, the Hg conc. in the leachate was above the median concentration, but still 50 times lower than the max concentration found in groundwater, indicating the possibilityof other sources. In conclusion, it proved difficult to quantitatively predict the mobility of metals in soils by sequential extractions.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Biodegradation of Injection Molded Starch-Poly (3-hydroxybutyrate-co-3-hydroxyvalerate) Blends in a Natural Compost Environment

Injection molded specimens were prepared by blending poly (hydroxybutyrate-co-valerate) (PHBV) with cornstarch. Blended formulations incorporated 30% or 50% starch in the presence or absence of poly-(ethylene oxide) (PEO), which enhances the adherence of starch granules to PHBV. These formulations were evaluated for their biodegradability in natural compost by measuring changes in physical and chemical properties over a period of 125 days. The degradation of plastic material, as evidenced by weight loss and deterioration in tensile properties, correlated with the amount of starch present in the blends (neat PHBV < 30% starch < 50% starch). Incorporation of PEO into starch-PHBV blends had little or no effect on the rate of weight loss. Starch in blends degraded faster than PHBV and it accelerated PHBV degradation. Also, PHBV did not retard starch degradation. After 125 days of exposure to compost, neat PHBV lost 7% of its weight (0.056% weight loss/day), while the PHBV component of a 50% starch blend lost 41% of its weight (0.328% weight loss/day). PHB and PHV moieties within the copolymer degraded at similar rates, regardless of the presence of starch, as determined by ¹H-NMR spectroscopy. GPC analyses revealed that, while the number average molecular weight (Mn) of PHBV in all exposed samples decreased, there was no significant difference in this decrease between neat PHBV as opposed to PHBV blended with starch. SEM showed homogeneously distributed starch granules embedded in a PHBV matrix, typical of a filler material. Starch granules were rapidly depleted during exposure to compost, increasing the surface area of the PHBV matrix.