Performance and fouling mechanism of direct contact membrane distillation (DCMD) treating fermentation wastewater with high organic concentrations

In this study,direct contact membrane distillation(DCMD)was used for treating fermentation wastewater with high organic concentrations.DCMD performance characteristics including permeate flux,permeate water quality as well as membrane fouling were investigated systematically.Experimental results showed that,after 12 hr DCMD,the feed wastewater was concentrated by about a factor of 3.7 on a volumetric basis,with the permeate flux decreasing from the initial 8.7 L/m~2/hr to the final 4.3 L/m~2/hr due to membrane fouling;the protein concentration in the feed wastewater was increased by about 3.5 times and achieved a value of 6178 mg/L,which is suitable for reutilization.Although COD and TOC in permeate water increased continuously due to the transfer of volatile components from wastewater,organic rejection of over 95%was achieved in wastewater.GC–MS results suggested that the fermentation wastewater contained 128kinds of organics,in which 14 organics dominated.After 12 hr DCMD,not only volatile organics including trimethyl pyrazine,2-acetyl pyrrole,phenethyl alcohol and phenylacetic acid,but also non-volatile dibutyl phthalate was detected in permeate water due to membrane wetting.FT-IR and SEM–EDS results indicated that the deposits formed on the membrane inner surface mainly consisted of Ca,Mg,and amine,carboxylic acid and aromatic groups.The fouled membrane could be recovered,as most of the deposits could be removed using a HCl/Na OH chemical cleaning method.     

Preparation of high concentration polyaluminum chloride with high content of Alb or Alc

A novel membrane distillation concentration method was used to prepare high concentration polyaluminum chloride (PACl) with high content of Al_b or Al_c. 2.52 mol/L PACl₁ with 88% Al_b and 2.38 mol/L PACl₂ with 61% Al_c were successfully prepared. Three coagulants, AlCl₃, PACl₁ and PACl₂ were investigated on their hydrolysis behavior and speciation under different conditions. The effects of pH and dilution ratio on Al species distribution were investigated by ferron assay. Experimental result showed that pH had a significant effect on Al species distribution for the three coagulants. Dilution ratio had little effects on Al_b and Al_c distribution in whole dilution process except the beginning for PACl₁ and PACl₂. The results indicated that transformation of Al depends largely on their original composition. AlCl₃ was the most unstable coagulant among these three coagulants during hydrolysis process. PACl₁ and PACl₂ with significant amounts of highly charged and stable polynuclear aluminum hydrolysis products were less affected by the hydrolysis conditions and could maintain high speciation stability under various conditions.     

硫酸根离子与聚合铝的反应过程及其产物形态

对不同Al/SO2-4比及碱化度条件下PACl与SO₄^2-的反应过程进行研究,分析了体系中总铝浓度及形态分布变化规律,测定了各沉淀/结晶产物的组成,并对其形貌进行了扫描电镜观察.实验结果表明:碱化度对PACl/SO₄^2-反应体系有较大影响,随着碱化度(B值)的增加,沉淀/结晶的析出速率加快,结果析出物中OH含量逐渐增加,而SO₄^2-/Al比率从0.45～0.30逐渐降低.各聚合铝水解形态与SO₄^2-反应速率上存在明显差异,从而为其混凝优势形态的分离纯化创造了条件.     

Drinking water treatment using a submerged internal-circulation membrane coagulation reactor coupled with permanganate oxidation

A submerged internal circulating membrane coagulation reactor(MCR) was used to treat surface water to produce drinking water. Polyaluminum chloride(PACl) was used as coagulant,and a hydrophilic polyvinylidene fluoride(PVDF) submerged hollow fiber microfiltration membrane was employed. The influences of trans-membrane pressure(TMP), zeta potential(ZP) of the suspended particles in raw water, and KMnO_4 dosing on water flux and the removal of turbidity and organic matter were systematically investigated. Continuous bench-scale experiments showed that the permeate quality of the MCR satisfied the requirement for a centralized water supply, according to the Standards for Drinking Water Quality of China(GB 5749-2006), as evaluated by turbidity(1 NTU) and total organic carbon(TOC)(5 mg/L)measurements. Besides water flux, the removal of turbidity, TOC and dissolved organic carbon(DOC) in the raw water also increased with increasing TMP in the range of 0.01–0.05 MPa. High ZP induced by PACl, such as 5–9 mV, led to an increase in the number of fine and total particles in the MCR, and consequently caused serious membrane fouling and high permeate turbidity.However, the removal of TOC and DOC increased with increasing ZP. A slightly positive ZP, such as 1–2 mV, corresponding to charge neutralization coagulation, was favorable for membrane fouling control. Moreover, dosing with KMnO_4 could further improve the removal of turbidity and DOC, thereby mitigating membrane fouling. The results are helpful for the application of the MCR in producing drinking water and also beneficial to the research and application of other coagulation and membrane separation hybrid processes.     

微塑料对膜蒸馏处理含锑高盐废水性能影响研究

研究了微塑料在膜蒸馏过程中不同温度、pH、微塑料浓度和微塑料粒径条件下对含锑高盐废水的处理性能及机理.结果表明,随着进料液温度的升高,饱和蒸汽压的增加提高了传质动力,不含微塑料时膜通量由17.4 L·m^-2·h^-1提高至20.7 L·m^-2·h^-1,通量提升了18.9%,含有微塑料时膜通量由15.6 L·m^-2·h^-1提高至18.5 L·m^-2·h^-1,提升了18.6%;pH由3增大至11时,由于重金属锑在不同pH条件下的价态变化及静电排斥作用,重金属锑截留率由98.2%提升至99.6%;微塑料浓度的增加会降低膜通量,提高锑截留效果,这可能是微塑料对溶液中重金属锑的吸附作用及微塑料在膜表面的积聚产生的筛分效应引起的.     

铝系混凝剂优势形态分析及其混凝特性

聚合氯化铝（PACl）是常用的水处理混凝剂,在应用过程中通常表现出比传统铝盐更为优异的效果.研究表明,这种优异性能主要得益于其特殊的组成,特别是高分子聚合物Al₁₃和Al₃₀独特的物化特性.Al₁₃和Al₃₀是铝离子水解过程中的中间产物,在地球科学和环境化学等领域有着重要的研究价值.于水处理而言,二者的结构和分子特性是研究者关注的重点,大量研究基于此展开,很多重要的发现为实际应用奠定了基础.基于对PACl及其组成性质的研究,本文对PACl的混凝特性及其优势形态分子的分析进行了综合阐述.     

不同铝聚合形态对聚合铝混凝效果的影响

通过氯化铝(铝单体或初聚物形态Ala)、高Alb含量聚合铝(中等聚合形态Alb)、高Alc含量聚合铝(铝溶胶等高聚合形态Alc)和工业PACl(不同聚合度铝的混合形态Alabc)对某水厂沉后水实际水样进行烧杯混凝实验,依据絮体生长状况、浊度、UV254、颗粒数和过滤指数等参数综合评价不同铝形态的混凝作用效果,从而得出铝的最佳混凝形态.结果表明,高Alb含量聚合铝对浊度去除较好;而高Alc含量聚合铝对于颗粒物和UV254的去除效果较佳.     

重力出流式膜生物反应器的膜通量及膜污染控制研究

采用新型的重力出流式膜生物反应器(MBR)处理生活污水和垃圾渗滤液,考察了其在长期运行过程中膜通量的变化规律及其影响因素.结果表明,该MBR能够在较低液位水头(8.5～15.0 kPa)的作用下连续出水,并获得较高的膜通量.处理生活污水时,平均膜通量为11.2 L·(m²·h)^-1;处理垃圾渗滤液时,平均膜通量为6.4 L·(m²·h)^-1.研究发现,污泥浓度对膜通量影响大小与曝气强度有关.当曝气强度小于400 m³·(m²·h)^-1时,膜通量随着污泥浓度的升高显著下降;当曝气强度大于400 m³·(m²·h)^-1时,膜通量几乎不受污泥浓度和曝气强度的影响.对膜的化学清洗试验表明,NaOH+NaClO溶液清洗效果最佳,膜通量可恢复至初始通量的85%以上.进一步研究表明,混合液中高浓度的溶解性胞外聚合物是MBR处理垃圾渗滤液时膜通量较低的主要原因.     

陶瓷膜接触器在润湿模式下吸收SO2的传质强化

将平均孔径为100 nm的Al_2O_3陶瓷膜组装成膜接触器,以单乙醇胺(MEA)为吸收剂,在考察吸收剂浓度对膜吸收过程影响的基础上,深入比较了陶瓷膜在润湿和非润湿模式下脱除SO_2的传质性能.实验结果表明,当MEA浓度大于0.26 mol·L~(-1)时,润湿模式下SO_2的脱除率和传质系数均高于非润湿模式.根据膜理论和阻力串联模型建立了陶瓷膜吸收SO_2的传质方程,理论计算表明,润湿模式下膜相传质阻力因瞬间化学反应的存在大幅降低,润湿模式更适用于脱除烟气中低浓度的SO_2.本研究结果可为陶瓷膜接触器在膜吸收领域的工业化应用和进一步传质优化提供参考.     

高浓度聚合氯化铝的合成及其形态分布与转化规律

以CaO为碱化剂采用一次加碱法合成了高浓度聚合氯化铝(PAC),研究了其反应特性及产品的铝形态分布与转化规律.结果表明,CaO特殊的水化反应可使PAC达到较高浓度和较高B值,PAC最高浓度可达2.1mol/L,B值为2.1.合成过程中无论高铝浓度体系还是低铝浓度体系,均存在一最佳B值,此B值下产品的Al_b含量最高.最佳B值和最高Al_b含量均随总铝浓度的升高而降低.B值小于最佳B值时,总反应主要表现为生成Al_b;B值大于最佳B值时,总反应表现为生成Al_c.     

印染废水反渗透脱盐系统运行性能及膜污堵特性

反渗透(RO)脱盐工艺对实现印染废水再生利用具有重要的意义.膜污堵却制约了RO工艺应用.对广东省某工业园区印染废水RO脱盐系统运行性能及膜污堵特性进行了研究.结果表明,印染废水生化处理出水经臭氧氧化-砂滤-超滤(UF)预处理后,RO进水COD平均浓度为12.4 mg·L~(-1),浊度1 NTU.RO系统脱盐率稳定在98%,RO产水高锰酸盐指数约为0.7 mg·L~(-1),浊度约为0.12 NTU.但RO系统运行3 a后,跨膜压差高达0.6 MPa,产水量下降至120 m~3·h~(-1),且不能通过化学清洗恢复,在RO膜面沉积了不可逆的污堵物.RO膜面的有机物占总污堵物干重的(53.5±0.2)%,无机物占(46.5±0.2)%,RO膜面有机污堵与无机污堵贡献相近.Si、Al与Ca是RO膜面主要的无机元素.碱液(Na OH溶液)对沉积在RO膜面的Si与Al及有机物提取效果较好.     

微絮凝对腐殖酸超滤过程膜污染的减缓特性

以硫酸铝[Al_2(SO_4)_3·18H_2O]为絮凝剂,腐殖酸(humic acid,HA)和高岭土(Kaolin)水溶液为原水,研究微絮凝过程产生的不同絮体形态,对自制聚偏氟乙烯(PVDF)超滤膜过滤过程的影响.主要考察了微絮凝过程中絮体的特性(粒径大小及分布,分形维数)以及不同条件下形成的絮体形态对膜通量的影响,利用扫描电镜(SEM)和原子力显微镜(AFM)对污染膜的表面形貌进行表征,并测定了PVDF膜与有机污染物之间黏附力大小,来解析不同絮体形态对超滤膜的膜污染影响机制.结果表明,Al~(3+)以电性中和作用水解去除有机物,随着絮凝剂投加量的增加,絮体粒径不断增大,絮体的分形维数减小.膜通量衰减速率与絮体的粒径呈负相关,絮体粒径越大,膜通量衰减速率越小,超滤过程中形成的滤饼层越疏松,同时,较小分形维数的絮体引起的膜污染较轻,其膜通量恢复率也较高.PVDF-有机污染物之间的相互作用力大小与运行初期相应污染膜通量衰减速率呈正相关.当Al~(3+)投加量为5 mg·L~(-1),初始pH=7时,HA去除率为96.7%,膜通量衰减最小,通量恢复率达到88%.     

反渗透用于APT离子交换废水的处理与回用

试验分别研究了反渗透膜Duraslick RO2540和RE2540-TE对APT冶炼离子交换废水的处理效果。研究结果表明,在最佳压力条件下,Duraslick RO2540膜对Cl-的截留率为91.4%,产水率为16.9%;RE2540-TE膜对Cl-的截留率为93.4%,产水率为17.2%。在压力为1.7MPa,温度为25℃时,浓缩实验结果表明,产水中Cl-浓度和膜的截留率随着时间变化而逐渐增加,但膜通量逐渐减小,且RE2540-TE膜通量下降幅度较大。清洗后,RE2540-TE膜通量损失达到6%,而Duraslick RO2540膜通量恢复幅度为98%。     

Effect of non-solvent additives on the morphology, pore structure, and direct contact membrane distillation performance of PVDF-CTFE hydrophobic membranes

Four common types of additives for polymer membrane preparation including organic macromolecule and micromolecule additives, inorganic salts and acids, and the strong non-solvent H2 O were used to prepare poly(vinylidene fluoride-co-chlorotrifluoroethylene)(PVDF-CTFE) hydrophobic flat-sheet membranes. Membrane properties including morphology, porosity, hydrophobicity, pore size and pore distribution were investigated, and the permeability was evaluated via direct contact membrane distillation(DCMD) of 3.5 g/L Na Cl solution in a DCMD configuration. Both inorganic and organic micromolecule additives were found to slightly influence membrane hydrophobicity. Polyethylene glycol(PEG),organic acids, Li Cl, Mg Cl2, and Li Cl/H2 O mixtures were proved to be effective additives to PVDF-CTFE membranes due to their pore-controlling effects and the capacity to improve the properties and performance of the resultant membranes. The occurrence of a pre-gelation process showed that when organic and inorganic micromolecules were added to PVDF-CTFE solution, the resultant membranes presented a high interconnectivity structure. The membrane prepared with dibutyl phthalate(DBP) showed a nonporous surface and symmetrical cross-section. When H2 O and Li Cl/H2 O mixtures were also used as additives, they were beneficial for solid–liquid demixing, especially when Li Cl/H2 O mixed additives were used. The membrane prepared with 5% Li Cl + 2% H2 O achieved a flux of24.53 kg/(m2·hr) with 99.98% salt rejection. This study is expected to offer a reference not only for PVDF-CTFE membrane preparation but also for other polymer membranes.     

臭氧-CNT膜改性联用工艺对PVDF中空纤维膜污染进程的缓解

采用碳纳米管(carbon nanotube,CNT)对聚偏氟乙烯(polyvinylidene fluoride,PVDF)中空纤维超滤膜进行改性,结合臭氧预氧化技术,考察了臭氧-CNT膜改性联用工艺对PVDF中空纤维膜污染进程的缓解作用,研究了CNT负载量和臭氧投量对中空纤维膜组件通量变化和抗污染性能的影响.结果表明,CNT负载量为3 g·m-2、臭氧投量(以O3/DOC计)为0.22mg·mg-1时,临界通量下[144 L·(m2·h)-1],膜组件单位面积过水量达到850 L·m-2,相比原始超滤膜过水量提高了4.5倍;低通量[18 L·(m2·h)-1]下运行15d,膜组件单位面积过水量达到3000 L·m-2,相比原膜单位过水量提高近10倍.使用共聚焦激光扫描电镜观测污染膜表面,结果表明,运行压力增长最快的原膜表面污染层内活菌数量最多;臭氧氧化与CNT膜均能够减少膜表面污染层内的微生物总量和活菌数量,从而缓解了运行压力的增长.臭氧氧化后CNT层的存在,进一步减少了膜表面污染层内的活菌数量,同时截留了部分死菌,但截留的死菌与运行压力增长无明显相关性.     

Membrane bioreactor process of organic wastewater from brassylic acid manufacturing plant

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｂｒａｓｓｙｌｉｃａｃｉｄｍａｎｕｆａｃｔｕｒｉｎｇｗａｓｔｅｗａｔｅｒｃｏｎｔａｉｎｓｈｉｇｈｃｈｅｍｉｃａｌｏｘｙｇｅｎｄｅｍａｎｄ(ＣＯＤ)ｃｏｎｃｅｎｔｒａｔｉｏｎ3000—12000ｍｇ/ＬａｎｄｉｔｓＢＯＤ5/ＣＯＤｉｓａｍｏｎｇ04—05Ｍｅａｎｗｈｉｌｅｔｈｅｗａｓｔｅｗａｔｅｒｃｏｎｔａｉｎｓｈｉｇｈｓｕｌｐｈａｔｅｃｏｎｃｅｎｔｒａｔｉｏｎａｂｏｕｔ13000ｍｇ/ＬａｎｄｉｔｓｐＨｖａｌｕｅｉｓｏｎｌｙ1—2Ａｃｈｅｍｉｃａｌｃｏｍｐａｎｙａｐｐｌｉｅｄｎｅｕｔｒａｌｉ…     

Al13形态在混凝中的作用机制

从铝的水解形态转化角度考察了铝盐在高碱度和高有机物浓度水体中的混凝行为.结果表明,铝盐的混凝效能是与混凝过程中的Al₁₃含量成正比.高投药量时氯化铝(AlCl₃)既可以有效调节水体pH值又能在混凝过程中原位水解产生较多的Al₁₃形态,因而混凝效能要高于聚合氯化铝(PACl).在铝盐混凝中,调节pH值到6～7之间可以控制铝形态分布从而达到提高混凝效能和减少残留铝的目的.在调节pH值强化混凝的方法中使用传统铝盐的效果要好于无机高分子絮凝剂.     

光催化/活性炭/纳滤组合工艺处理二级出水及对膜污染的控制

污水的资源化与回用可作为城市和各类建筑的非传统水源,必须满足相关水质标准,其中有机物一直是广泛关注的重要指标.本文采用华北某市大型污水厂的二级出水,研究了二氧化钛光催化氧化(UV-TiO_2)和颗粒活性炭(GAC)技术对溶解性有机物的去除特性以及对纳滤(NF)的膜污染控制特性,构建了UV-TiO_2/GAC/NF组合工艺,评价了组合工艺的有机物去除效能和膜污染控制作用,解析了影响NF膜污染程度的有机物种类和相对分子质量分布特征.结果表明,UV-TiO_2和GAC技术均可不同程度地缓解NF膜的不可逆污染、降低膜通量衰减速率; UV-TiO_2/GAC联用的不可逆膜污染程度比单独UV-TiO_2或GAC技术分别降低了48. 7%或61. 4%.类蛋白质和类腐殖质等有机污染物是不可逆膜污染的主要组分;相对分子质量为小于3×10~3和30×10~3～100×10~3的有机物是造成纳滤膜通量下降的主要因素. UV-TiO_2/GAC/NF组合工艺的COD、DOC和UV_(254)去除率为45. 7%、74. 5%和89. 2%,出水中COD、DOC和UV_(254)等有机物指标均得到有效去除.研究成果为城市和各类建筑非传统水源的深度净化与多途径回用提供了技术支持.     

Preparation of high concentration polyaluminum chloride with high content of Alb or Alc

A novel membrane distillation concentration method was used to prepare high concentration polyaluminum chloride (PACl) with high content of Alb or Alc. 2.52 mol/L PACl1 with 88% Alb and 2.38 mol/L PACl2 with 61% Alc were successfully prepared. Three coagulants, AlCl3, PACl1 and PACl2 were investigated on their hydrolysis behavior and speciation under di erent conditions. The e ects of pH and dilution ratio on Al species distribution were investigated by ferron assay. Experimental result showed that pH had a significant e ect on Al species distribution for the three coagulants. Dilution ratio had little e ects on Alb and Alc distribution in whole dilution process except the beginning for PACl1 and PACl2. The results indicated that transformation of Al depends largely on their original composition. AlCl3 was the most unstable coagulant among these three coagulants during hydrolysis process. PACl1 and PACl2 with significant amounts of highly charged and stable polynuclear aluminum hydrolysis products were less a ected by the hydrolysis conditions and could maintain high speciation stability under various conditions.     

浸入式超滤膜工艺稳定运行影响因素研究

以确定浸入式超滤膜工艺稳定运行工况为目标,进行了混凝.浸入式超滤膜工艺处理滦河原水的中试研究.采用横跨膜压差(TMP)做为表征膜稳定运行的工艺参数,考察了膜通量、制水周期、原水水质条件的改变对膜工艺的影响.结果表明,采用浸入式膜处理滦河水时,膜通量为53.3 L/(m2·h)且制水周期为30 min时膜工艺运行稳定,能较好控制膜污染;水温变化对膜工艺运行影响较大,低温期单个过滤周期TMP比高藻期增加了76%;EFM和化学清洗结合是一种有效地控制膜污染、强化稳定运行的措施.