Characteristics of flow structure of free-surface flow in a partly obstructed open channel with vegetation patch

Free-surface flows over patchy vegetation are common in aquatic environments. In this study, the hydrodynamics of free-surface flow in a rectangular channel with a bed of rigid vegetation-like cylinders occupying half of the channel bed was investigated and interpreted by means of laboratory experiments and numerical simulations. The channel configurations have low width-to-depth aspect ratio (1.235 and 2.153). Experimental results show that the adjustment length for the flow to be fully developed through the vegetation patch in the present study is shorter than observed for large-aspect-ratio channels in other studies. Outside the lateral edge of the vegetation patch, negative velocity gradient (\(\partial \overline{u}/\partial z < 0\)) and a local velocity maximum are observed in the vertical profile of the longitudinal velocity in the near-bed region, corresponding to the negative Reynolds stress (\(- \overline{{u^{\prime}w^{\prime}}} < 0\)) at the same location. Assuming coherent vortices to be the dominant factor influencing the mean flow field, an improved Spalart–Allmaras turbulence model is developed. The model improvement is based on an enhanced turbulence length scale accounting for coherent vortices due to the effect of the porous vegetation canopy and channel bed. This particular flow characteristic is more profound in the case of high vegetation density due to the stronger momentum exchange of horizontal coherent vortices. Numerical simulations confirmed the local maximum velocity and negative gradient in the velocity profile due to the presence of vegetation and bed friction. This in turn supports the physical interpretation of the flow processes in the partly obstructed channel with vegetation patch. In addition, the vertical profile of the longitudinal velocity can also be explained by the vertical behavior of the horizontal coherent vortices based on a theoretical argument.     

Hydrodynamics and turbulence in emergent and sparsely vegetated open channel flow

This present study reports the results of an experimental study characterizing thorough variation of turbulent hydrodynamics and flow distribution in emergent and sparsely vegetated open channel flow. An emergent and rigid sparse vegetation patch with regular spacing between stems along the flow and transverse directions was fixed in the central region of the cross-section of open channel. Experiments were conducted in subcritical flow conditions and velocity measurements were obtained with an acoustic Doppler Velocimetry system. Large variations of the turbulence intensities, Reynolds shear stress, turbulent kinetic energy and vortical motions are found in and around the vegetation patch. At any cross-section through the interior of the vegetation patch, streamwise velocity decreases with increase in streamwise length and the velocity profiles converge from the log-law to a linear profile with increasing slope. Time-averaged lateral and vertical velocities inside the vegetation patch increase with increasing streamwise distance and converge from negative values to positive values. Turbulence intensities interior of the sparse vegetation patch are more than those of without the vegetation patch. Similar to the trend of streamwise velocity profiles inside the vegetation, turbulence intensities and longitudinal-normal Reynolds shear stress profile decreases with streamwise direction. In the interior of the vegetation patch and downstream of the trailing edge, turbulent kinetic energy profiles are exhibiting irregular fluctuations and the maximum values are occurring in the outer layer. Analysis of flow distribution confirms sparse vegetation patch is inducing a serpentine flow pattern in its vicinity. At the leading edge, flow is rushing towards the right hand sidewall, and at the trailing edge, flow is turning to the left hand sidewall. In between the leading and trailing edges, the streamlines are following a zig-zag fashion at varied degree along the streamwise and lateral directions. Immediate upstream of the leading edge and in the interior of the vegetation patch, vortex motion is clearly visible and the vortices are stretched along the width of the channel with streamwise direction.     

Flow structure and turbulence characteristics downstream of a spanwise suspended linear array

Laboratory experiments are conducted to quantify the mean flow structure and turbulence properties downstream of a spanwise suspended linear array in a uniform ambient water flow using Particle Tracking Velocimetry. Eighteen experimental scenarios, with four depth ratios (array depth to water column depth) of 0.35, 0.52, 0.78, and 0.95 and bulk Reynolds number (length scale is the array depth) from 11,600 to 68,170, are investigated. Three sub-layers form downstream of the array: (1) an internal wake zone, where the time-averaged velocity decreases with increasing distance downstream, (2) a shear layer which increases in vertical extent with increasing distance downstream of the array, and the rate of the increase is independent of the bulk Reynolds number or the depth ratio, and (3) an external wake layer with enhanced velocity under the array. The location of the shear layer is dependent on the depth ratio. The spatially averaged and normalized TKE of the wake has a short production region, followed by a decay region which is comparable to grid turbulence decay and is dependent on the depth ratio. The results suggest that the shear layer increases the transfer of horizontal momentum into the internal wake zone from the fluid outside of the array and that the turbulence in the internal wake zone can be modeled similarly to that of grid turbulence.     

Spatial evolution of coherent motions in finite-length vegetation patch flow

A number of experimental studies on submerged canopy flows have focused on fully-developed flow and turbulent characteristics. In many natural rivers, however, aquatic vegetation occurs in patches of finite length. In such vegetated flows, the shear layer is not formed at the upstream edge of the vegetation patch and coherent motions develop downstream. Therefore, more work is neededz to reveal the development process for large-scale coherent structures within vegetation patches. For this work, we considered the effect of a limited length vegetation patch. Turbulence measurements were intensively conducted in open-channel flows with submerged vegetation using Particle Image Velocimetry (PIV). To examine the transition from boundary-layer flow upstream of the vegetation patch to a mixing-layer-type flow within the patch, velocity profiles were measured at 33 positions in a longitudinal direction. A phenomenological model for the development process in the vegetation flow was developed. The model decomposed the entire flow region into four zones. The four zones are the following: (i) the smooth bed zone, (ii) the diverging flow zone, (iii) the developing zone and (iv) the fully-developed zone. The PIV data also confirmed the efficiency of the mixing-layer analogy and provided insight into the spatial evolution of coherent motions.     

Analytical model for vertical velocity profiles in flows with submerged shrub-like vegetation

An analytical solution for the vertical profiles of the horizontal velocity of channel flow with submerged shrub-like vegetation is investigated in this paper. At first, a shape function is proposed to fit the diameter change of different types of shrub-like vegetation. Using the momentum theorem and the mixing-length turbulence model, an analytical solution for the vertical profile of the horizontal velocity within the vegetation is obtained. The velocity distribution of the whole column is determined in tandem with the logarithmic velocity profile above the vegetation. The solution is compared with experimental data in excellent agreement. The results show that the flow above the vegetation has a logarithmic velocity profile while the flow within the vegetation is impacted greatly by the shape and density of vegetation. The flows within shrub-like vegetations are non-uniform and vary inversely with the shrub diameter.     

Flow structure of unconfined turbidity currents interacting with an obstacle

Driven by a growing importance to engineered structures, investigating the flow characteristics of turbidity currents interacting with a basal obstruction has become popular over the last three decades. However, research has focused on confined studies or numerical simulations, whereas in situ turbidity currents are typically unconfined. The present study investigates experimentally the velocity and turbulence structure of an unconfined turbidity current, in the immediate regions surrounding a rectangular obstacle. Initial density of the current, and substrate condition is varied. Through a novel technique of installing ultrasonic probes within the obstacle, the presence of a velocity recirculation region immediately upstream and downstream of the obstacle is revealed and confirmed with high-resolution imagery. This was found to be comparable to previous confined studies, suggesting that stream-wise velocity profile structure is somewhat independent of confinement. The obstacle was found to reduce velocity and turbulence intensity maxima downstream of the obstacle when compared with unobstructed tests.     

Hydrodynamics and bed stability of open channel flows with submerged foliaged plants

In this work we investigate experimentally and numerically the flow structure around foliaged plants deployed in a channel with gravels on the bed under submerged and barely submerged conditions. Velocity and Reynolds stress were measured by using a NORTEK Vectrino profiler. Visual observation shows that the initial motion of gravels is easier to be triggered under the condition of flow with barely submerged vegetation. This is confirmed by the measured velocity, Reynolds stress and total kinetic energy (TKE) profiles. The velocity exhibits a speed up in the near-bed region, and the associated Reynolds stress and TKE increase there. A 3D numerical model is then verified against the experiments and used to investigate systematically the effect of degree of submergence of foliaged plants on the channel bed shear stress. The results show that the maximum bed shear stress occurs when the foliage is situated slightly below the water surface, which can enhance channel bed instability.     

2D numerical analysis of the influence of near-bank vegetation patches on the bed morphological adjustment

This paper investigates the influence of near-bank vegetation patches on the bed morphological adjustment in open channel flow systems. The 2D depth-averaged hydro-morphological model is adopted for this investigation, which is first validated by laboratory experimental data measured in an open channel with a single near-bank vegetation patch. The validated model is then applied for extensive numerical simulations, with the aim of conducting a systematic analysis of the influence of different geometric controlling parameters on the bed morphological evolution. The controlling parameters taken into account for numerical analysis include the angle of repose value (RAV) of sediment, vegetation density (VD), patch length (PL) and patch width (PW). The numerical results and analysis show that: (1) the RAV of sediment with slope-failure parametrization only influences the shape of the transverse bed topography in the junction region; (2) increase in VD, PL and PW that substantially enhances flow blockage effect encourages the growth of the pool adjacent to the patch in three dimensions; (3) increase in VD, PL and PW produces analogous retrogressive erosion (erosion toward the upstream) in the pool region, presumably due to the increase in flow resistance. Additional numerical experiments suggest that the staggered-order distribution of multiple patches might be an optimal choice for channel restoration and conservation since pools and riffles with larger scales can be produced.

     

Modelling hydraulic jump using the bubbly two-phase flow method

Hydraulic jumps have complex flow structures, characterised by strong turbulence and large air contents. It is difficult to numerically predict the flows. It is necessary to bolster the existing computer models to emphasise the gas phase in hydraulic jumps, and avoid the pitfall of treating the phenomenon as a single-phase water flow. This paper aims to improve predictions of hydraulic jumps as bubbly two-phase flow. We allow for airflow above the free surface and air mass entrained across it. We use the Reynolds-averaged Navier–Stokes equations to describe fluid motion, the volume of fluid method to track the interface, and the k–ε model for turbulence closure. A shear layer is shown to form between the bottom jet flow and the upper recirculation flow. The key to success in predicting the jet flow lies in formulating appropriate bottom boundary conditions. The majority of entrained air bubbles are advected downstream through the shear layer. Predictions of the recirculation region’s length and air volume fraction within the layer are validated by available measurements. The predictions show a linear growth of the shear layer. There is strong turbulence at the impingement, and the bulk of the turbulence kinetic energy is advected to the recirculation region via the shear layer. The predicted bottom-shear-stress distribution, with a peak value upstream of the toe of the jump and a decaying trend downstream, is realistic. This paper reveals a significant transient bottom shear stress associated with temporal fluctuations of mainly flow velocity in the jump. The prediction method discussed is useful for modelling hydraulic jumps and advancing the understanding of the complex flow phenomenon.     

Dominant features in three-dimensional turbulence structure: comparison of non-uniform accelerating and decelerating flows

The results are presented from an experimental study to investigate three-dimensional turbulence structure profiles, including turbulence intensity and Reynolds stress, of different non-uniform open channel flows over smooth bed in subcritical flow regime. In the analysis, the uniform flow profiles have been used to compare with those of the non-uniform flows to investigate their time-averaged spatial flow turbulence structure characteristics. The measured non-uniform velocity profiles are used to verify the von Karman constant κ and to estimate sets of log-law integration constant B_r and wake parameter П, where their findings are also compared with values from previous studies. From κ, B_r and П findings, it has been found that the log-wake law can sufficiently represent the non-uniform flow in its non-modified form, and all κ, B_r and П follow universal rules for different bed roughness conditions. The non-uniform flow experiments also show that both the turbulence intensity and Reynolds stress are governed well by exponential pressure gradient parameter β equations. Their exponential constants are described by quadratic functions in the investigated β range. Through this experimental study, it has been observed that the decelerating flow shows higher empirical constants, in both the turbulence intensity and Reynolds stress compared to the accelerating flow. The decelerating flow also has stronger dominance to determine the flow non-uniformity, because it presents higher Reynolds stress profile than uniform flow, whereas the accelerating flow does not.     

Design and Testing of a Turbulence Probe for Harsh Flows

The force of wind on the ground created by turbulent eddies is commonly used to describe the horizontal flux of material during wind erosion. Here we present the Murdoch Turbulence Probe, an instrument for use in both clean and eroding flows which uses pressure differences to measure the three components of wind velocity. Correlation techniques calculate the forces near the ground and turbulence statistics in nearly real time, including turbulent velocity fluctuations from less than 0.1 Hz to 200 Hz, mean flow velocities, Reynolds stresses as well as the integral length and time scales. In the portable wind-tunnel used by Agriculture Western Australia, turbulence statistics were recorded over stable surfaces and in blowing sand from the initiation of erosion up to the time the sand supply was exhausted. Estimates of the friction velocity derived from the turbulence probe were compared with estimates obtained from the wind speed profile measured with a rake of pitot and static tubes. The Murdoch Turbulence Probe appears to work well in sandblasting conditions. Relative turbulence intensities ranged from 0.11 to 0.2 and are in close agreement with values in the literature. The ratio of the turbulence to the friction velocity (3 to 3.2) is at the high end of the reported range. The Reynolds stress measurements agree closely with predictions of the threshold friction velocities of the sand and estimates from the wind speed profile with a von Kármán constant of about 0.3, lower than the commonly accepted value of 0.4. We suggest that the wind-tunnel profile represents the `outer layer' of the boundary-layer that may best be described by a `Wake Law' or `Defect Law'. At about 54 mm above the surface, the friction velocity decreases from 0.64 m/s to 0.39 m/s and the mean velocity increases from 9.6 m/s to 11.6 m/s as the supply of sand is depleted. In addition to the friction velocity, other scales may be necessary to characterise the overriding effect of the wind and in extending wind-tunnel results to the field.     

Steady Shallow-Water Current and Solute Transport around a Semi-Conical Headland

Laboratory experiments have been carried out to investigate the effects of a sloping wall headland on the flow characteristics and the associated concentration distributions from a point source around the headland. A semi-conical headland with a slope of 1:2 was set up in a flow basin, 4.8 m long and 3.8 m wide. In this paper, the experimental results of a steady shallow-water current are reported. Three dimensional flow velocities in the basin were measured using Sontek-ADV instrument. The dye concentration levels in the basin were measured by two fluorometers. The experimental results showed a large-scale re-circulation region behind the semi-conical headland. The peak turbulence energy, at about 53% of the local kinetic flow energy, coincides with the region of high velocity gradient. Significant vertical flows were observed around the area near the downhill slope of the headland, with a maximum ratio of vertical to horizontal velocities being about 22%. Such relatively significant vertical scouring velocities, coupled with strong turbulence energy and high horizontal velocity gradients in the same region, could cause severe bed erosion. The experimental results have also been compared with the predicted results of a depth-averaged numerical model. The predicted eddy structure and the concentration distribution in the re-circulation area were found to compare favourably with the experimental results. However, the discrepancies in the flow velocities and the concentration levels near the headland were apparent. It was observed that the dye concentration continued to spread in the cross-stream direction after passing the headland, whereas only a limited extent of the lateral spreading was predicted by the numerical model further downstream of the headland.     

Compound channel flow with a longitudinal transition in hydraulic roughness over the floodplains

Flows in a compound open-channel (two-stage geometry with a main channel and adjacent floodplains) with a longitudinal transition in roughness over the floodplains are experimentally investigated in an 18 m long and 3 m wide flume. Transitions from submerged dense vegetation (meadow) to emergent rigid vegetation (wood) and vice versa are modelled using plastic grass and vertical wooden cylinders. For a given roughness transition, the upstream discharge distribution between main channel and floodplain (called subsections) is also varied, keeping the total flow rate constant. The flows with a roughness transition are compared to flows with a uniformly distributed roughness over the whole length of the flume. Besides the influence of the downstream boundary condition, the longitudinal profiles of water depth are controlled by the upstream discharge distribution. The latter also strongly influences the magnitude of the lateral net mass exchanges between subsections, especially upstream from the roughness transition. Irrespective of flow conditions, the inflection point in the mean velocity profile across the mixing layer is always observed at the interface between subsections. The longitudinal velocity at the main channel/floodplain interface, denoted \(U_{int}\), appeared to be a key parameter for characterising the flows. First, the mean velocity profiles across the mixing layer, normalised using \(U_{int}\), are superimposed irrespective of downstream position, flow depth, floodplain roughness type and lateral mass transfers. However, the profiles of turbulence quantities do not coincide, indicating that the flows are not fully self-similar and that the eddy viscosity assumption is not valid in this case. Second, the depth-averaged turbulent intensities and Reynolds stresses, when scaled by the depth-averaged velocity \(U_{d,int}\) exhibit two plateau values, each related to a roughness type, meadow or wood. Lastly, the same results hold when scaling by \(U_{d,int}\) the depth-averaged lateral flux of momentum due to secondary currents. Turbulence production and magnitude of secondary currents are increased by the presence of emergent rigid elements over the floodplains. The autocorrelation functions show that the length of the coherent structures scales with the mixing layer width for all flow cases. It is suggested that coherent structures tend to a state where the magnitude of velocity fluctuations (of both horizontal vortices and secondary currents) and the spatial extension of the structures are in equilibrium.     

Turbulence characteristics within sparse and dense canopies

Boundary layer interactions with canopies control various environmental processes. In the case of dense and homogeneous canopies, the so-called mixing layer analogy is most generally used. When the canopy becomes sparser, a transition occurs between the mixing layer and the boundary layer perturbed by interactions between element wakes. This transition has still to be fully understood and characterized. The experimental work presented here deals with the effect of the canopy density on the flow turbulence and involves an artificial canopy placed in a fully developed turbulent boundary layer. One and two-component velocity measurements are performed, both within and above the canopy. The influence of the spacing between canopy elements is studied. Longitudinal velocity statistical moments and Reynolds stresses are calculated and compared to literature data. For spacings greater than the canopy height, evidences of this transition are found in the evolution of the skewness factor, shear length scale and mixing length.     

Simulation of exchange flow between open water and floating vegetation using a modified RNG <Emphasis Type="Italic">k</Emphasis>-<Emphasis Type="Italic">ε</Emphasis> turbulence model

The paper focuses on the numerical simulation of the exchange flow between open water and floating vegetation, which plays an important role in maintaining the ecological balance by transporting nutrient matter. The simulation was conducted using a new solver developed upon OpenFOAM. A modified RNG k-ε turbulence model, which is expected to model both the high- and low-Reynolds number flows correctly, was used to determine the eddy viscosity. Several particular terms were added into the momentum equations and turbulence model equations to model the effects of vegetation and buoyancy. Among these terms, the term for the effect of vegetation in the ε-equation was re-modelled. The model was validated by properly predicting the profiles of mean velocity and turbulent kinetic energy for flows through suspended canopies. The density flow between open and vegetated water was simulated with the same conditions as those of the experiment conducted by Zhang and Nepf. The predicted results agreed well with the experimental data and provided more detailed information of such exchange flow. The convection between the root layer and the layer beneath the roots, which was not observed in the experiment, was observed in the numerical simulation.     

Experimental Study of the Criteria of Flow Laminarization in Two-Dimensional Dense Gas Plumes

Laminarization of flow in a two-dimensional dense gas plume was experimentally investigated in this study. The plume was created by releasing CO₂ through a ground-level line source into a simulated turbulent boundary layer over an aerodynamically rough surface in a meteorological wind tunnel. The bulk Richardson number (Ri_*), based on negative plume buoyancy, plume thickness, and friction velocity, was varied over a wide range so that the effects of stable stratification on plume laminarization could be observed. A variety of ambient wind speeds as well as three different sizes of roughness arrays were used so that possible effects of roughness Reynolds number (Re_*) on plume laminarization could also be identified. Both flow visualization methods and quantitative measurements of velocity and intermittency of turbulence were used to provide quantitative assessments of plume laminarization.Flow visualization provided an overall picture of how the plume was affected by the negative buoyancy. With increasing Ri_*, both the plume depth and the vertical mixing were significantly suppressed, while upstream propagation of the plume from the source was enhanced. The most important feature of the flow revealed by visualization was the laminarization of flow in the lower part of the plume, which appeared to be closely related to both Ri_* and Re_*.Measurements within the simulated dense gas plumes revealed the influence of the stable stratification on mean velocity and turbulence intensity profiles. Both the mean velocity and turbulence intensity were significantly reduced near the surface; and these reductions systematically depended on Ri_*. The roughness Reynolds number also had considerable influence on the mean flow and turbulence structure of the dense gas plumes.An intermittency analysis technique was developed and applied to the digitized instantaneous velocity signals. It not only confirmed the general flow picture within the dense plume indicated by the flow visualization, but also clearly demonstrated the changes of flow regime with variations in Ri_* and Re_*. Most importantly, based on this intermittency analysis, simple criteria for characterizing different flow regimes are formulated; these may be useful in predicting when plume laminarization might occur.     

Turbulence investigation in the roughness sub-layer of a near wall flow

The turbulence behaviour along a wall roughened by pyramidal elements was analysed in the region extending from the apex of the roughness elements up to the external limit of the roughness sub-layer. The data used for the analysis were obtained by particle image velocimetry technique. The rough wall turbulent boundary layer flow is characterized by a relatively low Reynolds number. All the results on the rough wall were compared with data referring to the canonical flow on a smooth wall turbulent boundary layer. Mean values and turbulence quantities for the two flows collapse when approaching the external limit of the roughness sublayer. The quadrant analysis of the Reynolds shear stress, in the region near the surface, shows that the contribution of the sweep motions is about equivalent for the two flows (except for wall distances lower than 40 viscous units). The contribution of the ejection motions appears to be more important over the smooth wall than over the rough wall with increasing differences approaching the wall. The probability density functions of the streamwise fluctuating velocity field for the rough wall case appear to be positively skewed in the zone very close to the pyramid apex, in contrast with the behavior observed for the smooth wall case at corresponding distances from the wall. The integral and Taylor scales for the rough wall case appear to be strongly reduced by the presence of the roughness, while the Kolmogorov microscale shows higher values.     

Experimental study of recirculating flows generated by lateral shock waves in very large channels

Due to the lack of data on hydraulic-jump dynamics in very large channels, the present paper describes the main characteristics of the velocity field and turbulence in a large rectangular channel with a width of 4 m. Although a hydraulic jump is always treated as a wave that is transversal to the channel wall, in the case of this study it has a trapezoidal front shape, first starting from a point at the sidewalls and then developing downstream in an oblique manner, finally giving rise to a trapezoidal shape. The oblique wave front may be regarded as a lateral shockwave that arises from a perturbation at a certain point of the lateral wall and travels obliquely toward the centreline of the channel. The experimental work was carried out at the Coastal Engineering Laboratory of the Water Engineering and Chemistry Department of the Technical University of Bari (Italy). In addition to the hydraulic jump formation, a large recirculating flow zone starts to develop from the separating point of the lateral shock wave and a separate boundary layer occurs. Intensive measurements of the streamwise and spanwise flow velocity components along one-half width of the channel were taken using a bidimensional Acoustic Doppler Velocimeter (ADV). The water surface elevation was obtained by means of an ultrasonic profiler. Velocity vectors, transversal velocity profiles, turbulence intensities and Reynolds shear stresses were all investigated. The experimental results of the separated boundary layer were compared with numerical predictions and related work presented in literature and showed good agreement. The transversal velocity profiles indicated the presence of adverse pressure gradient zones and the law of the wall appears to govern the region around the separated boundary layer.     

Turbulent secondary flows in wall turbulence: vortex forcing,scaling arguments,and similarity solution

Spanwise surface heterogeneity beneath high-Reynolds number, fully-rough wall turbulence is known to induce a mean secondary flow in the form of counter-rotating streamwise vortices—this arrangement is prevalent, for example, in open-channel flows relevant to hydraulic engineering. These counter-rotating vortices flank regions of predominant excess(deficit) in mean streamwise velocity and downwelling(upwelling) in mean vertical velocity. The secondary flows have been definitively attributed to the lower surface conditions, and are now known to be a manifestation of Prandtl’s secondary flow of the second kind—driven and sustained by spatial heterogeneity of components of the turbulent (Reynolds averaged) stress tensor (Anderson et al. J Fluid Mech 768:316–347, 2015). The spacing between adjacent surface heterogeneities serves as a control on the spatial extent of the counter-rotating cells, while their intensity is controlled by the spanwise gradient in imposed drag (where larger gradients associated with more dramatic transitions in roughness induce stronger cells). In this work, we have performed an order of magnitude analysis of the mean (Reynolds averaged) transport equation for streamwise vorticity, which has revealed the scaling dependence of streamwise circulation intensity upon characteristics of the problem. The scaling arguments are supported by a recent numerical parametric study on the effect of spacing. Then, we demonstrate that mean streamwise velocity can be predicted a priori via a similarity solution to the mean streamwise vorticity transport equation. A vortex forcing term has been used to represent the effects of spanwise topographic heterogeneity within the flow. Efficacy of the vortex forcing term was established with a series of large-eddy simulation cases wherein vortex forcing model parameters were altered to capture different values of spanwise spacing, all of which demonstrate that the model can impose the effects of spanwise topographic heterogeneity (absent the need to actually model roughness elements); these results also justify use of the vortex forcing model in the similarity solution.     

Experimental investigation of bubbly flow and turbulence in hydraulic jumps

Many environmental problems are linked to multiphase flows encompassing ecological issues, chemical processes and mixing or diffusion, with applications in different engineering fields. The transition from a supercritical flow to a subcritical motion constitutes a hydraulic jump. This flow regime is characterised by strong interactions between turbulence, free surface and air–water mixing. Although a hydraulic jump contributes to some dissipation of the flow kinetic energy, it is also associated with increases of turbulent shear stresses and the development of turbulent eddies with implications in terms of scour, erosion and sediment transport. Despite a number of experimental, theoretical and numerical studies, there is a lack of knowledge concerning the physical mechanisms involved in the diffusion and air–water mixing processes within hydraulic jumps, as well as on the interaction between the free-surface and turbulence. New experimental investigations were undertaken in hydraulic jumps with Froude numbers up to Fr = 8.3. Two-phase flow measurements were performed with phase-detection conductivity probes. Basic results related to the distributions of void fraction, bubble frequency and mean bubble chord length are presented. New developments are discussed for the interfacial bubble velocities and their fluctuations, characterizing the turbulence level and integral time scales of turbulence representing a “lifetime” of the longitudinal bubbly flow structures. The analyses show good agreement with previous studies in terms of the vertical profiles of void fraction, bubble frequency and mean bubble chord length. The dimensionless distributions of interfacial velocities compared favourably with wall-jet equations. Measurements showed high turbulence levels. Turbulence time scales were found to be dependent on the distance downstream of the toe as well as on the distance to the bottom showing the importance of the lower (channel bed) and upper (free surface) boundary conditions on the turbulence structure.