改性活性炭吸附净化黄磷尾气中的H2S

研究了以Cu2 离子活性溶液制备改性活性炭吸附净化黄磷尾气中H2S的相关问题,考察了改性活性炭制备过程中的浸渍液浓度、干燥温度和焙烧温度的影响,以及温度和氧含量对吸附的影响;并对空白活性炭、改性活性炭吸附前后做SEM表征.研究结果表明,浸渍液浓度0.05 mol/L、干燥温度120℃、焙烧温度250℃为改性活性炭制备的最佳条件;吸附反应阶段较适宜的温度为95℃,氧含量为1%;结合扫描电镜初步表明,改性后的活性炭S容量增加,吸附效果明显.     

改性活性炭吸附净化黄磷尾气中的H2S

研究了以Cu²⁺离子活性溶液制备改性活性炭吸附净化黄磷尾气中H₂S的相关问题,考察了改性活性炭制备过程中的浸渍液浓度、干燥温度和焙烧温度的影响,以及温度和氧含量对吸附的影响;并对空白活性炭、改性活性炭吸附前后做SEM表征。研究结果表明,浸渍液浓度0.05 mol/L、干燥温度120℃、焙烧温度250℃为改性活性炭制备的最佳条件;吸附反应阶段较适宜的温度为95℃,氧含量为1%;结合扫描电镜初步表明,改性后的活性炭S容量增加,吸附效果明显。     

表面改性活性炭对水中头孢拉定的吸附性能

为了研究改性前后活性炭对水中低浓度头孢拉定的吸附效果,探讨了投加量、初始浓度、温度、p H值和时间对吸附去除率的影响。结果表明,经Fe(NO3)3溶液改性后,活性炭对头孢拉定的吸附能力得到加强;经Fe(NO3)3溶液浸渍改性获得的活性炭对头孢拉定的吸附,能很好地与Langmuir型等温方程拟合,线性相关数达0.98以上;吸附过程符合二级反应动力学描述,线性相关数达0.998以上。     

微波辐照活性炭还原氮氧化物

为提高烟气脱硝效率,构建了微波辐照活性炭还原氮氧化物体系,通过对微波功率(温度)、反应空速、NO浓度、活性炭种类及粒径等影响因素的考察,研究了微波辐照活性炭还原NO体系的性能,通过反应动力学实验确定了活性炭还原NO反应的速率方程。研究结果表明,增大微波功率、减小反应空速均会提高NO还原效率,而改变NO浓度、活性炭种类以及粒径对NO还原效率无明显影响,微波功率为800 W,反应空速为2 000 h~(-1)时,对2 412 mg·m~(-3)的NO去除率可达99.8%,当NO浓度增至29 000 mg·m~(-3)时NO还原效率仍高达98.2%。通过反应动力学研究确定了反应的速率方程,其中反应级数为0.568 3,反应速率常数为14.71 s~(-1)。     

银负载对活性炭纤维汞吸附性能的影响

银氨溶液浸渍活性炭纤维制得载银量14.07%的载银活性炭纤维.以筒状吸附体吸附气态Hg0的方式研究活性炭纤维银载前后的汞吸附性能,结果表明,载银后活性炭纤维汞吸附性能明显提高.实验还发现:随吸附温度升高,活性炭纤维的汞吸附效率随先增加后降低,而载银活性炭纤维的汞吸附效率随吸附温度升高而一直降低;延长停留时间和添加H2O(g)对两者汞吸附均有利.采用片状吸附体对2种吸附剂的汞饱和吸附量进行了测定,实验得出:70℃下活性炭纤维汞饱和吸附量为29.4 mg/g,载银活性炭纤维汞饱和吸附量为192.3 mg/g,即活性炭纤维载银后汞饱和吸附量提高到原来的6.54倍.扫描电镜分析发现:活性炭纤维上物理吸附汞占绝大多数,化学吸附汞很少;负载银后汞只吸附在活性炭纤维的含银活性点上,银粒子与汞结合生成银汞齐后形状趋于规则,且主要分布于活性炭纤维微晶的晶棱交界处.     

热解气活化的活性炭对水体中甲萘威的吸附性能

以生物质混合压缩颗粒为原料,在600~900℃活化温度下,循环利用热解气制备活性炭,考察热解气的活化作用及活性炭对农药甲萘威的吸附性能。结果表明:热解气具有明显的活化作用,经过活化的炭与热解炭相比孔结构更加发达,表面更加粗糙;活化温度对活性炭理化性质具有显著影响,随温度升高,活性炭芳香性升高,极性降低,含氧官能团逐渐减少,比表面积由239.00 m~2·g~(-1)增加到629.20 m~2·g~(-1),平均孔径由5.438 nm减小至3.005 nm;Freundlich模型能够很好地拟合活性炭对甲萘威的吸附等温线,随活化温度升高,活性炭吸附能力增大;吸附动力学更符合伪二级反应动力学模型,60 h内基本实现吸附平衡;当活化温度为800℃,单位原料对甲萘威的吸附量最大。     

改性活性炭对水中铬离子(Ⅵ)的吸附性能

为了研究改性前后活性炭对水中铬离子(Ⅵ)的吸附效果,以磷酸活性炭(PAC)为原料,用10%硝酸改性得到硝酸改性活性炭(N-PAC)及直接蒸发法载铁改性得到载铁活性炭(Fe-PAC)。通过静态吸附研究表明,改性后活性炭对Cr(Ⅵ)的吸附率有较大提高。在常温、自然pH条件下,0.2 g活性炭处理50 mL浓度为100 mg/L的含Cr(Ⅵ)溶液,N-PAC和Fe-PAC对Cr(Ⅵ)的吸附率分别为79.21%和90.59%,都高于原PAC对Cr(Ⅵ)的吸附率49.58%。pH从2.2升高到11.92,Fe-PAC对Cr(Ⅵ)的吸附率从99.86%降低到14.77%,N-PAC则从99.86%降低到3.23%,PAC从97.05%降低到2.53%。温度从25℃升高到70℃,3种活性炭对Cr(Ⅵ)吸附率都有较大提高,都增加到98%以上。且吸附过程较符合Langmuir等温吸附模型。     

溶胶-凝胶法制备颗粒状催化剂低温SCR脱硝性能

采用溶胶凝胶法制备了Mn-Ce/Ti O2催化剂,并将其用于低温NH3选择催化还原NO的反应(NH3-SCR),考察了反应温度、空速、氧气浓度、氮氧化物浓度和氨氮比等反应条件对催化剂性能的影响。结果表明,NO入口浓度为800~1 600 mg/m3时,催化剂活性受NO初始浓度的影响较小。反应温度和氨氮比对NO转化率影响显著,100~150℃温度范围内,NO转化率随温度升高快速上升;当[NH3]/[NO]1.1时,随着[NH3]/[NO]的增加,NO转化率很快上升。反应体系中适当的O2浓度可促进NO还原为N2。空速大于10 000 h-1时,NO转化率随着空速的增大而降低。     

高比表面微孔活性炭的制备及其对对硝基苯胺的吸附

以互花米草与棉秆为原料,以KOH为活化剂,制备了高比表面微孔活性炭,利用氮气吸附、红外光谱FT-IR、扫描电子显微镜SEM等技术对活性炭表面物化性质进行了表征与分析,并通过静态实验测定了其对对硝基苯胺的吸附性能。结果表明,在KOH与植物茎秆碳化料的质量比为3∶1、温度为800℃、活化时间为1.5 h条件下,制备的棉秆活性炭CS-AC和互花米草活性炭SA-AC的BET比表面积分别为2 135和2 825 m2/g,H-K微孔容积分别为1.09和1.19 cm3/g,有80%以上的孔分布在2 nm以内。静态吸附实验表明,2种植物基活性炭对对硝基苯胺有较强的吸附能力,Langmu ir最大吸附量超过700 mg/g。吸附受溶液pH影响较大,Frend lich方程能较好地描述静态吸附平衡数据。     

浸渍改性活性碳纤维吸附氮氧化物性能

为实现新风在通过空调进入室内前已被优化的目的,搭建了一套开式循环系统。通过对活性碳纤维进行浸渍改性,采用比表面测定、SEM观察、XPS分析、傅里叶变换红外谱图分析对改性前后活性碳纤维进行了表征;定量研究了室外氮氧化物初始浓度、温度和风速等环境因素对改性前后活性碳纤维吸附氮氧化物效率的影响。结果表明,改性对活性碳纤维表面活性官能团种类、含氧官能团数量、表面微观结构及比表面积等特性均有显著影响,提高了其对氮氧化物的吸附效率;室外初始浓度、风速、温度对改性前后活性碳纤维吸附氮氧化物效率的变化趋势基本一致;改性前后活性碳纤维对氮氧化物的吸附率随初始浓度的升高而逐渐降低,随过滤器处风速增大先升高后降低,随过滤器处温度的升高先升高后降低。改性后活性碳纤维对空气中氮氧化物的吸附率明显提高,可以将其应用于空调系统中。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.