Degradation of tert-butyl formate and its intermediates by an ozone/UV process

In this paper, the oxidation of tert-butyl formate (TBF) in aqueous solution by an ozone/UV process was described. The oxidation process was investigated experimentally in a semibatch reactor. The results of the study indicated that the ozone/UV process was very effective in oxidizing TBF. tert-Butyl alcohol (TBA), hydroxy-iso-butyraldehyde (HiBA), acetone, formaldehyde, and formic acid were identified as major primary intermediates during the oxidation of TBF. About 90% organic carbon balance was obtained indicating that most reaction intermediates have been identified and quantified. Some of the primary intermediates were also oxidized in the ozone/UV system. Accordingly, HiBA, acetone, formaldehyde, and formic acid were the primary intermediates of TBA oxidation. The oxidation of acetone in the ozone/UV system generated formaldehyde, pyruvaldehyde, acetic acid, formic acid as primary intermediates. It was also observed that the reaction intermediates formed during the oxidation of TBF react well in the ozone/UV system and complete mineralization could be achieved by the process.     

Degradation of tert-butyl formate and its intermediates by an ozone/UV process

In this paper, the oxidation of tert-butyl formate (TBF) in aqueous solution by an ozone/UV process was described. The oxidation process was investigated experimentally in a semibatch reactor. The results of the study indicated that the ozone/UV process was very effective in oxidizing TBF. tert-Butyl alcohol (TBA), hydroxy-iso-butyraldehyde (HiBA), acetone, formaldehyde, and formic acid were identified as major primary intermediates during the oxidation of TBF. About 90% organic carbon balance was obtained indicating that most reaction intermediates have been identified and quantified. Some of the primary intermediates were also oxidized in the ozone/UV system. Accordingly, HiBA, acetone, formaldehyde, and formic acid were the primary intermediates of TBA oxidation. The oxidation of acetone in the ozone/UV system generated formaldehyde, pyruvaldehyde, acetic acid, formic acid as primary intermediates. It was also observed that the reaction intermediates formed during the oxidation of TBF react well in the ozone/UV system and complete mineralization could be achieved by the process.     

UV/Fenton法处理间-甲酚废水

利用UV/Fenton工艺对模拟间-甲苯酚废水进行了处理,研究了H2O2加入量、FeSO4加入量、pH、原水初始COD值、环境温度、反应时间等因素对COD去除率的影响.实验表明：间-甲苯酚浓度为100mg/L、初始COD值251 mg/L的废水,在30℃下,pH为4.Q,[H2O2]/[Fe^2＋]=15（质量浓度比）,紫外灯照射3 h后,COD去除率达86.3%,若再经Ca（OH）2絮凝沉降,则COD去除率提高到92.6%.同时,对Fenton及UV/Fenton的处理效果进行了比较,实验表明：UV/Fenton的处理效果明显优于Fenton法.     

UV/Fenton法处理间-甲酚废水

利用UV/Fenton工艺对模拟间-甲苯酚废水进行了处理,研究了H2O2加入量、FeSO4加入量、pH、原水初始COD值、环境温度、反应时间等因素对COD去除率的影响.实验表明:间-甲苯酚浓度为100mg/L、初始COD值251 mg/L的废水,在30℃下,pH为4.Q,[H2O2]/[Fe2 ]=15(质量浓度比),紫外灯照射3 h后,COD去除率达86.3%,若再经Ca(OH)2絮凝沉降,则COD去除率提高到92.6%.同时,对Fenton及UV/Fenton的处理效果进行了比较,实验表明:UV/Fenton的处理效果明显优于Fenton法.     

Treatment of fluorine-containing pharmaceutical wastewater by VUV/UV process

Environmental Science and Pollution Research - As an advanced oxidation process, vacuum ultraviolet/ultraviolet (VUV/UV) has been intensively studied for drinking water treatment, but assessment of...     

臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

Heap leaching of Pb and Zn contaminated soil using ozone/UV treatment of EDTA extractants

The feasibility of a novel EDTA-based soil heap leaching method with treatment and reuse of extractants in a closed process loop was evaluated on a laboratory scale. Ozone and UV irradiation were used for oxidative decomposition of EDTA-metal complexes in extractants from Pb (1243 mg kg(-1)) and Zn (1190 mg kg(-1)) contaminated soil. Released metals were absorbed in a commercial metal absorbent Slovakite. Six-consecutive additions of 2.5 mmol kg(-1) EDTA (total 15 mmol kg(-1) EDTA) removed 49.6 +/- 0.6% and 19.7 +/- 1.7% of initial total Pb and Zn from soil (4.6 kg) packed in 22 cm high columns. The efficiency of extraction was similar to small-scale simulations of heap leaching (15 0 g of soil), where EDTA used in the same manner removed 49.7 +/- 1.0% and 13.7 +/- 0.4% of Pb and Zn. The new heap leaching method produced discharge extractant with fairly low final concentrations of Pb, Zn and EDTA (1.98 +/- 2.17 mg l(-1), 4.55 +/- 2.36 mg l(-1), and 0.05 +/- 0.04 mM, respectively), which could presumably be reduced even further with continuation of treatment. The results of our study indicate that for soils contaminated primarily with Pb, treating the EDTA extractants with ozone/UV and reuse of extractants enables efficient soil heap leaching with very little or no wastewater generation, easy control over emissions, and lowers the requirements for process water.     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

Decomposition of 2-nitrophenol in aqueous solution by ozone and UV/ozone processes.

The decomposition of 2-nitrophenol in aqueous solutions by ozone and UV/ozone processes was found to be technically feasible under adequate experimental conditions. Formation of nitrate ions was observed following the decomposition of 2-nitrophenol by ozone and UV/ ozone processes. Increasing ozone dosage and UV light intensity accelerated the decomposition rate of 2-nitrophenol in an aqueous solution. The species distribution of 2-nitrophenol under various solution conditions plays a significant role in determining decomposition behavior. In most experiments conducted in this study, the decomposition of 2-nitrophenol by ozone and UV/ozone processes was favored to occur in alkaline conditions. The addition of 2-butanol accelerated the rate of gaseous ozone transfer to an aqueous phase by reducing the surface tension of aqueous solution and therefore enhancing the decomposition rate of 2-nitrophenol by ozone and UV/ozone processes.     

臭氧气浮工艺处理城市合流制溢流污染

合流制溢流(CSO)污水具有水质水量波动大、非连续产生的特点,采用臭氧气浮技术对CSO污水进行处理,研究该技术对化学需氧量(COD)、总磷(TP)、悬浮固体(SS)等污染指标的控制效果。实验室小试结果表明,在最适工艺条件下,混凝-臭氧同步处理对CSO实际污水SS、TP、COD去除率分别为77.8%、73.6%和57.9%,显著削弱了腐殖质类有机物荧光强度,混凝与臭氧氧化之间表现出良好的协同作用,能够实现CSO污染的有效控制。进一步设计了臭氧气浮撬装式设备,并在武汉市开展了CSO处理现场实验研究,运行结果表明,臭氧气浮工艺系统对SS、TP、COD的平均去除率分别为81.8%、75.4%和61.7%,净化效果良好,实现了对CSO典型污染物的协同治理。通过实验室研究和工程实验结果,证实了臭氧气浮工艺用于CSO污水治理的工程可行性,上述研究结果可为CSO污水的多水质目标协同控制提供理论指导和技术参考。     

臭氧深度氧化法处理2,4-二氯苯氧乙酸农药废水

对臭氧深度氧化法降解农药2,4-二氯苯氧乙酸(2,4-D)废水进行了研究。实验结果表明,紫外光催化臭氧化降解2,4-D成效显著,臭氧/紫外(UV)深度氧化法是最好的臭氧化处理方法。2,4-D200mg/L的水样,反应30min,2,4-D降解完全,75min时矿化率达75%以上。碱性反应氛围有利于臭氧化反应进行。自由基抑制剂(叔丁醇)的加入,显著降低臭氧化反应去除2,4-D的效果,自由基参与的反应历程对于2,4-D的降解十分重要。双氧水的引入对2,4-D降解无明显促进作用,这是因为双氧水分解消耗OH-,没有缓冲的反应体系pH降低,限制了双氧水的分解和.OH自由基链反应。总之,单独臭氧化对2,4-D降解有一定的反应效率,在有利于.OH产生的体系中,2,4-D降解效率进一步提高。     

UV/Fenton法预处理N-甲基苯胺生产废水

采用UV/Fenton法对N-甲基苯胺生产废水进行预处理。当原水COD约为3 400 mg/L时,在适宜操作条件（H₂O₂投加量为50 mL/L,Fe²⁺投加量为1.209 g/L,pH＝5.0,反应时间为30 min）下的COD去除率可达90％以上。同时得到Fenton试剂处理该废水的适宜条件为：H₂O₂投加量为60 mL/L,Fe²⁺投加量为1.692 g/L,pH为5.0,反应时间30 min;单独UV辐照处理该废水的较适宜条件为：反应时间为20 min, pH＝5.0。最后就3种处理方法进行了比较,发现UV对Fenton试剂处理N-甲基苯胺生产废水具有一定促进作用。反应前后的紫外光谱说明,经UV/Fenton反应后,原水中的含苯环物质已得到了彻底的氧化分解。     

高硬度富锶地下水的软化沉淀-超滤膜联用工艺

针对一种高硬度富锶地下水,分别采用石灰和石灰-碳酸钠两种方法,利用药剂软化/超滤膜工艺对其进行软化处理,同时考察了药剂投量对出水锶含量的影响。结果表明,采用石灰软化/超滤膜法,Ca(OH)2最佳投加量为270 mg/L时,出水总硬度(以CaCO3计)由287.12 mg/L降低到96.44 mg/L,硬度去除率为66.41%,出水锶含量也由原水中的0.37 mg/L下降为0.21 mg/L;而采用石灰-碳酸钠软化/超滤膜法,Ca(OH)2和Na2CO3最佳投加量分别为270 mg/L、160mg/L时,出水总硬度降低到60.34 mg/L,硬度去除率达78.98%,锶含量仅为0.02 mg/L。2种处理方法出水总硬度均达到预期目标,石灰软化/超滤膜法可使出水锶含量满足富锶水的要求,而石灰-碳酸钠软化/超滤膜法则造成了对人体有益微量元素锶的大量损失。     

臭氧光催化降解地下水中天然有机物的研究

在现场开展了中试规模的臭氧光催化降解天然有机物的研究.研究表明,对大分子天然有机物占很大比例且重碳酸盐含量较高的地下水,臭氧投加量10 mg/L和反应时间10 min条件下,TOC的去除率不到20%,但UV254和三卤甲烷生成潜力(THMFP)去除率分别达到近60%和33.5%.臭氧光催化与活性炭吸附相连,能显著提高UV254的THMFP的去除率,但TOC去除率并不明显高于单独活性炭吸附.臭氧光催化使大分子有机物转化为小分子有机物,后者在活性炭上的吸附性提高且生化性改善,可望在生物活性炭上更有效地去除.     

臭氧光催化降解地下水中天然有机物的研究

在现场开展了中试规模的臭氧光催化降解天然有机物的研究。研究表明，对大分子天然有机物占很大比例且重碳酸盐含量较高的地下水，臭氧投加量10mg／L和反应时间10min条件下，TOC的去除率不到20％，但uV254和三卤甲烷生成潜力（THMFP）去除率分别达到近60％和33．5％。臭氧光催化与活性炭吸附相连，能显著提高UV254的THMFP的去除率，但TOC去除率并不明显高于单独活性炭吸附。臭氧光催化使大分子有机物转化为小分子有机物，后者在活性炭上的吸附性提高且生化性改善，可望在生物活性炭上更有效地去除。     

UV/ozone degradation of gaseous hexamethyldisilazane (HMDS)

As a carcinogen, hexamethyldisilazane (HMDS) is extensively adopted in life science microscopy, materials science and nanotechnology. However, no appropriate technology has been devised for treating HMDS in gas streams. This investigation evaluated the feasibility and effectiveness of the UV (185+254nm) and UV (254nm)/O(3) processes for degradation of gaseous HMDS. Tests were performed in two batch reactors with initial HMDS concentrations of 32-41mgm(-3) under various initial ozone dosages (O(3) (mg)/HMDS (mg)=1-5), atmospheres (N(2), O(2), and air), temperatures (28, 46, 65 and 80 degrees C), relative humilities (20%, 50%, 65%, 99%) and volumetric UV power inputs (0.87, 1.74, 4.07 and 8.16Wl(-1)) to assess their effects on the HMDS degradation rate. Results indicate that for all conditions, the decomposition rates for the UV (185+254nm) irradiation exceeded those for the UV (254nm)/O(3) process. UV (185+254nm) decompositions of HMDS displayed an apparent first-order kinetics. A process with irradiation of UV (185+254nm) to HMDS in air saturated with water at temperatures of 46-80 degrees C favors the HMDS degradation. With the condition as above and a P/V of around 8Wl(-1), k was approximately 0.20s(-1) and a reaction time of just 12s was required to degrade over 90% of the initial HMDS. The main mechanisms for the HMDS in wet air streams irradiated with UV (185+254nm) were found to be caused by OH free-radical oxidation produced from photolysis of water or O((1)D) produced from photolysis of oxygen. The economic evaluation factors of UV (185+254nm) and UV (254nm)/O(3) processes at different UV power inputs were also estimated.     

Decomposition of gas phase 1,3-butadiene by ultraviolet/ozone process

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O3) and ultraviolet (UV)/O3 technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of approximately 50 ppm, an ambient temperature of 26 degrees C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O3, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo-first-order with respect to BD concentrations. Moisture content (relative humidity = 40-99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

UV/Fenton氧化处理PVA溶液

为了对PVA(聚乙烯醇)溶液中PVA去除进行研究,采用UV/Fenton氧化技术氧化处理PVA溶液。探究了UV/Fenton氧化PVA溶液的影响因素,主要研究了反应时间、初始pH、H2O2/COD和H2O2/Fe2+,获得了各个因素对PVA溶液COD去除率的影响规律以及PVA溶液经处理后的B/C(BOD5/COD)变化规律。实验表明,随着H2O2/COD投加比的增加,COD去除率不断增加,B/C呈现先增加后减少的现象;随初始pH的增加,COD去除率以及B/C均呈现先增加后减少的现象;随着H2O2/Fe2+不断增加,COD去除率以及B/C均呈现先增加后减少的现象;随反应时间的增加,COD去除率以及B/C均增加之后趋于稳定。当H2O2/COD=1.5,pH=4,H2O2/Fe2+物质的量之比为10,T=30 min时COD去除率效果比较好,经过处理之后溶液的 B/C由0.1 增至0.6,可生化性提高,为后续生物处理创造条件。     

UV/Fenton法处理EDTA-Cu-Ni络合废水

为了探索络合态重金属废水的处理方法,采用UV/Fenton氧化技术处理EDTA-Cu-Ni模拟废水,主要研究了Fe2+投加量、H2O2投加量、初始pH和UV光照时间等因素对COD、Cu2+和Ni2+去除效果的影响及机理。结果表明,随着Fe2+和H2O2投加量以及初始pH的升高,COD、Ni2+的去除率先升后降,Cu2+的去除率则在升高后趋于稳定;随着UV光照时间的增加,COD、Cu2+、Ni2+去除效率均呈上升趋势并逐渐达到平衡。结合成本和效率考虑,得出最佳处理条件为：Fe2+投加量为10 mmol·L-1,H2O2投药量为600 mmol·L-1,反应初始pH为3.0,UV光照时间为120 min。在UV/Fenton体系中,UV光照能增强Fenton反应的去除效率,异丙醇对反应的抑制说明羟基自由基在处理过程中是重要的活性物种。     

UV/H_2O_2/TiO_2联合水解酸化+MBR工艺处理亚砜废水

二甲基亚砜(DMSO)废水因其COD高、可生化性差的特性而较难处理。本实验以采用硫酸二甲酯法生产DMSO的某化工厂废水为研究对象,设计并建立了组合式光催化氧化装置联合水解酸化+MBR工艺的中试系统,探讨了组合式光催化氧化装置、氧化剂投加量、pH、反应时间和水力停留时间对系统处理效果的影响。结果表明,组合式光催化氧化装置可有效提高DMSO废水的可生化性。最优工艺参数为:按H2O2与原水COD质量浓度比为2∶1投加H2O2,在pH值为4、反应时间为6 h、水力停留时间为4 h的条件下,该系统对原水COD(5 000 mg/L)去除率大于98%,出水COD达到《污水综合排放标准》(GB 8978-1996)一级要求。