Numerical and wind tunnel modeling on the windbreak effectiveness to control the aeolian erosion of conical stockpiles

There are many industrial sites where open aggregate conical piles exist to store granular materials, like coal, industrial residuals, or other minerals. Usually these storage piles are placed in open areas, making them susceptible to wind erosion, which can create health, environmental, and/or economical concerns. It is common to minimize the dust emission through the placement of windbreaks in the vicinity of the storage piles, which reduces the wind speed in the vicinity of the pile’s surface. In this work, some experimental results from a wind tunnel study on the erosion of a conical sand pile, exposed or protected by a fence with porosities of 0, 70, and 83%, are shown. For the sheltered cases, the windbreak was placed at several distances from the pile’s leading edge, ranging from H to 4H, where H is the initial height of the non-eroded pile. The evolution of the shape of the sand pile is shown, at different instances in time, and the pile deformation quantified, using a novel experimental setup developed for wind erosion studies. This information might be regarded as a useful dataset for the benchmark of computational models aiming to produce the transient simulation of the aeolian erosion of stockpiles. The CFD results are comprised of the modeling of several experimental scenarios. The computational results for the surface wind velocity show a good correlation with the initial deformation of the pile. Based on the results, the isocontours of (u _s /u _r ) presented might be regarded as a good basis for the estimation of the pile shear velocity.     

Experimental surface flow visualization and numerical investigation of flow structure around an oblong stockpile

Emission factors are largely used to quantify particle emissions from industrial open storage piles. These factors are based on the knowledge of velocity distribution and flow patterns over the stockpile surface which still requires further research. The aim of the present work is to investigate the airflow characteristics over a single typical oblong pile and in its near-ground surroundings for various wind flow directions. Wind tunnel experiments using an oil-film surface coating technique were carried out for near-wall flow visualization. Numerical simulation results, favorably compared to PIV measurements, were used to allow comparison analysis of flow features. For the stockpile oriented 90° to the wind main direction, typical topology of flow around wall-mounted obstacles were observed, notably a wake zone downstream the pile including two main counter-rotating vortices. Further analysis of numerical wall shear stress distribution and streamlines indicates that two complex three-dimensional vortical flow structures develop downstream the pile. For other incoming wind flow directions (30 and 60°), the flow characteristics over the storage pile greatly differ as a single helical main vortex develops from the pile’s crest. Corresponding high values of wall shear stress are noticed downstream the storage pile. For each configuration studied, downwash and upwash zones are induced by the vortical structures developed. This near-wall flow topology combined with areas of high friction levels may be linked to potential dust emission from the ground surface surrounding industrial stockpiles.     

Aeolian erosion of storage piles yards: contribution of the surrounding areas

Dust emissions from stockpiles surfaces are often estimated applying mathematical models such as the widely used model proposed by the USEPA. It employs specific emission factors, which are based on the fluid flow patterns over the near surface. But, some of the emitted dust particles settle downstream the pile and can usually be re-emitted which creates a secondary source. The emission from the ground surface around a pile is actually not accounted for by the USEPA model but the method, based on the wind exposure and a reconstruction from different sources defined by the same wind exposure, is relevant. This work aims to quantify the contribution of dust re-emission from the areas surrounding the piles in the total emission of an open storage yard. Three angles of incidence of the incoming wind flow are investigated ( $30^{\circ }, 60^{\circ }$ and $90^{\circ }$ ). Results of friction velocity from numerical modelling of fluid dynamics were used in the USEPA model to determine dust emission. It was found that as the wind velocity increases, the contribution of particles re-emission from the ground area around the pile in the total emission also increases. The dust emission from the pile surface is higher for piles oriented $30^{\circ }$ to the wind direction. On the other hand, considering the ground area around the pile, the $60^{\circ }$ configuration is responsible for higher emission rates (up to 67 %). The global emissions assumed a minimum value for the piles oriented perpendicular to the wind direction for all wind velocity investigated.     

Numerical simulation of sand dune erosion

Erosion of sand or other granular material is a subject of utmost importance in several fields of practical interest, including industrial processes or environmental issues. Resulting from intricate interaction between the incident flow field and localized body forces responsible for the granular material cohesion, erosion is a particularly complex phenomenon. The present work addresses this problem, proposing a numerical method to compute the time evolution of a sand dune subjected to aeolian erosion, along with the associated entrainment and deposition fluxes. Turbulent fluid flow is computed through a three-dimensional Navier-Stokes solver based on a generalized coordinate system. A Lagrangian approach is adopted for tracking the trajectories of particles entrained in the saltation regime, thus allowing prediction of the corresponding deposition locations. Different models for saltation fluxes are tested, along with several formulations for the creeping-to-saltation flux ratio, creeping threshold and creeping distance. Comparison with results from wind tunnel experiments is very encouraging, stressing the relative importance of creeping in the erosion process for the presently studied conditions.     

Development and testing of a micro wind tunnel for on-site wind erosion simulations

Wind erosion processes affect soil surfaces across all land uses worldwide. Understanding the spatial and temporal scales of wind erosion is a challenging undertaking because these processes are diverse and highly variable. Wind tunnels provide a useful tool as they can be used to simulate erosion at small spatial scales. Portable wind tunnels are particularly valued because erosion can be simulated on undisturbed soil surfaces in the field. There has been a long history of use of large portable wind tunnels, with consensus that these wind erosion simulation tools can meet real world aerodynamic criteria. However, one consequence of striving to meet aerodynamic reality is that the size of the tunnels has increased, making them logistically difficult to work with in the field and resulting in a tendency to homogenise naturally complex soil surfaces. This homogenisation is at odds with an increasing awareness of the importance that small scale processes have in wind erosion. To address these logistical and surface homogenisation issues we present here the development and testing of a micro wind tunnel (MWT) designed to simulate wind erosion processes at high spatial resolution. The MWT is a duct-type design—0.05 m tall 0.1 m wide and with a 1.0 m working section. The tunnel uses a centrifugal motor to suck air through a flow‐conditioning section, over the working section and then through a sediment collection trap. Simulated wind velocities range from 5 to 18 m s^?1, with high reproducibility. Wind speeds are laterally uniform and values of u _* at the tunnel bed (calculated by measuring the pressure gradients within the MWT) are comparable with those of larger tunnels in which logarithmic profiles can be developed. Saltation sediment can be added. The tunnel can be deployed by a single person and operated on slopes ranging from 0 to 10°. Evidence is presented here that the MWT provides new and useful understanding of the erodibility of rangelands, claypans and ore stockpiles.     

Influence of non-erodible particles with multimodal size distribution on aeolian erosion of storage piles of granular materials

Environmental Fluid Mechanics - Aeolian erosion of granular materials is investigated by means of a mathematical emission model and experimental wind tunnel measurements. Main model input data are:...     

Prediction of particulate air pollution from a landfill site using CFD and LIDAR techniques

Landfill sites have been the most common way of eliminating solid urban waste, as well as that of public and mining wastes. Landfill sites are a constant source of environmental pollution and wind is the most important contributing factor to air pollution, due to the erosion which it produces over the landfill site surfaces, transporting dust away from the source point. This causes serious risks for human health and general dirt in the surrounding areas of the landfill site. The result of dust air pollution produced in a landfill site is analysed through CFD3D (Computational Fluid Dynamics) by joining the LIDAR (Light Detection and Ranging) technique and Ansys CFX 10.0 software. The CFD simulations determine the wind velocity distribution on the landfill site surface and the different particle threshold friction velocities which determine the dust emission in multiphase simulations (air-particles). These simulations are validated from field data obtained in three measurement programmes for each type of landfill site surface treatment which has been studied. It was determined that the superficial landfill site treatment with the lowest air pollution is tall grass and bushes. The methodology used can be applied to the dust emission calculation in the design or evaluation of other landfill sites.     

Numerical and experimental analysis of wind erosion on a sinusoidal pile

Erosion is a common phenomenon in nature, and it may cause a wide range of problems such as air pollution, and destruction of agricultural land, shelters and stockpiles. The present work deals with stockpiles, which have their profiles described by a sinus function or by similar trigonometric functions. Analysis of the erosion by air flow over these piles will provide for further understanding of the erosion underlying mechanisms and, moreover, how to control them and eventually to prevent them. To this purpose, different experimental tests are conducted for a pile with a sinuous profile, and particular attention is given to the time development of the profile due to the erosion process; the effect of the air velocity is also studied by selecting different velocities. In addition, the flow over several deformed piles is numerically predicted using the CFX software; the results clearly show the erosion process is strongly dependent upon time, velocity field and surface disturbances. A correlation between the erosion rate and the velocity is proposed.     

Development of source profiles and their application in source apportionment of PM<Subscript>2.5</Subscript> in Xiamen,China

Ambient PM_2.5 samples were collected at four sites in Xiamen, including Gulangyu (GLY), Hongwen (HW), Huli (HL) and Jimei (JM) during January, April, July and October 2013. Local source samples were obtained from coal burning power plants, industries, motor vehicles, biomass burning, fugitive dust, and sea salt for the source apportionment studies. The highest value of PM_2.5 mass concentration and species related to human activities (SO₄ ^2–, NO₃ ^–, Pb, Ni, V, Cu, Cd, organic carbon (OC) and elemental carbon (EC)) were found in the ambient samples from HL, and the highest and lowest loadings of PM_2.5 and its components occurred in winter and summer, respectively. The reconstructed mass balance indicated that ambient PM_2.5 consisted of 24% OM (organic matter), 23% sulfate, 14% nitrate, 9% ammonium, 9% geological material, 6% sea salt, 5% EC and 10% others. For the source profiles, the dominant components were OC for coal burning, motor vehicle, biomass burning and sea salt; SO₄ ^2– for industry; and crustal elements for fugitive dust. Source contributions were calculated using a chemical mass balance (CMB) model based on ambient PM_2.5 concentrations and the source profiles. GLY was characterized by high contributions from secondary sulfate and cooking, while HL and JM were most strongly affected by motor vehicle emissions, and biomass burning and fugitive dust, respectively. The CMB results indicated that PM_2.5 from Xiamen is composed of 27.4% secondary inorganic components, 20.8% motor vehicle emissions, 11.7% fugitive dust, 9.9% sea salt, 9.3% coal burning, 5.0% biomass burning, 3.1% industry and 6.8% others.

Open image in new window

     

Evaluation of wind environment around a residential complex using a PIV velocity field measurement technique

Wind-tunnel simulations were employed to evaluate the wind environment around a tested residential area located near industrial complexes. The scaled-down geomorphological model of the test area was placed in the test section of a boundary layer wind tunnel. Particle image velocimetry (PIV) measurements were made in five vertical planes and one horizontal plane around the test area for two prevailing wind directions. The results showed that the wind speed decreased in the near surface layer and the velocity fluctuations increased in the upper region due to the presence of hills and high-rise buildings around the test area. Regions of flow separation and low-speed flow were found inside the test area for both the wind directions. The result suggests that the high-rise buildings should be well arranged with respect to the main wind directions to increase the natural ventilation inside the residential complex at the initial design stage.     

An approach to simulate wind fields around an urban environment for wind energy application

This work proposes an approach to simulate wind flow fields around an urban environment with the aim of evaluating the potential impact of buildings on the general wind patterns and power production using the current generation of commercial wind turbines. The simulation process was performed with the aid of accessible computational tools that can potentially render the proposed procedure applicable in other cases of interest. The roughness of the urban environment was defined as the association of roughness map, topography, and an alternative process for obtaining the volumetry of buildings. A case study was conducted in a region located at the district of Boa Viagem (Recife-PE) for assessing the applicability of the approach. Scenarios were designed in order to simulate wind flow patterns and pre-identify sites that have suitable wind energy potential for electric power production by investigating the combination of wind speed magnitude and turbulence intensity. From the results obtained, it was possible to identify zones of potential wind sources that are not detected in classical wind atlas probably due to the influence of the built environment on local wind flow patterns.     

Dust emission calculations in open storage piles protected by means of barriers, CFD and experimental tests

The importance of open mineral storage piles in bulk solids port terminals have increased considerably in recent years in Europe and USA (in Spain, great extensions of transoceanic ports are being made) to address the increasing demand of raw material importation due to local mining operation closure. These storage piles are affected by the climatologically processes and the dust emission to the atmosphere, causing repercussions to health and environmental, which is intimately related to the air velocity, according to USEPA studies, maximum ratio of dust emission emitted from CFD and software Ansys CFX 10.0 is determined. In addition, an emission variability study based on the pile distance of different height solid barriers is developed, reducing the emission to 66%. The studies have been contrasted by published investigations and industrial measurement.     

Do lower electricity storage costs reduce greenhouse gas emissions?

In the electricity sector, innovation in large-scale storage is anticipated to reduce costs and improve performance. The effect on greenhouse gas emissions of lower storage costs depends on the interactions between storage and the entire grid. The literature has disagreed on the role of storage in reducing emissions. In this paper we present a stylized model, which suggests that the effect of storage costs on emissions depends on the supply responsiveness of both fossil and renewable generators. Under common conditions in the United States, lower storage costs are more likely to reduce emissions when wind investment responds to equilibrium electricity prices and when solar investment does not. Simulations of a computational model of grid investment and operation confirm these intuitions. Moreover, because of its effect on coal and natural gas–fired supply responsiveness, introducing a carbon dioxide emissions price may increase the likelihood that lower storage costs reduce emissions.     

Obergrenze für den Dioxingehalt von Ackerböden

A value of 100 ng TEQ/kg is proposed for dioxin-contaminated plowland due to the emissions of these soils by wind erosion. The emissions are compared with those of modern incineration plants.     

Health risk assessment for arsenic contaminated soil

This paper describes risk assessment methods for two chronic exposure pathways involving arsenic contaminated soil, namely inhalation of fugitive dust emissions over a lifetime, and inadvertent soil/house dust ingestion. The endpoint in the first case is assumed to be lung cancer and in the second case skin cancer. In order to estimate exposures, inhalation rates and soil/dust ingestion rates are estimated for different age groups; indoor/outdoor time budgets for different age groups are developed; and indoor surface dust and air arsenic concentrations are estimated based on outdoor concentration measurements. Differences observed in indoor/outdoor ratios and arsenic containing dust particle size among different types of communities are noted, as well as possible relationship of particle size to bioavailability. Calculations of risk are presented using cancer potency factors developed by the U.S. Environmental Protection Agency, and uncertainties in these toxicity estimates are described based on: (1) evidence that arsenic may be neither a cancer initiator nor promotor, but may act instead as a late stage carcinogen and (2) evidence that the arsenic dose-response relationship for ingestion may be nonlinear at low doses due to increasing methylation of inorganic arsenic. The first of these considerations influences the relative importance ascribed to arsenic doses in different age groups. The latter consideration indicates that the risk estimates described here are probably very conservative.     

Efficient air pollution abatement for regions in China

This paper computes the efficient air pollution abatement ratios of 30 regions in China during the period 1996–2002. Three air emissions (SO₂, soot and dust) are considered. Data envelopment analysis (DEA) with a single output (real GDP) and five inputs (labour, real capital stock, SO₂, dust and soot emissions) is used to compute the target emissions of each region for each year. The efficient abatement ratios of each region in each year are then obtained by dividing the target emission by the actual emission of an air pollutant. Our major findings are: 1. The eastern area is the most efficient region with respect to SO₂, soot and dust emissions in every year during the research period. 2. The eastern, central and western areas have the lowest, medium and highest 1996–2002 average target abatement ratios of SO₂ (22.09%, 42.23% and 57.58%), soot (26.19%, 56.34% and 66.37%) and dust (15.20%, 29.09% and 40.59%), respectively. 3. These results are consistent with the Environmental Kuznets Curve (EKC) theory, whereby a more developed area will use environmental goods more efficiently than a less developed area. 4. Compared to dust emission, the average target abatement ratios for SO₂ and soot emissions (as direct outcomes of burning coal) are relatively much higher for all three areas.     

Physiological and metabolic effect of mercury accumulation in higher plants system

Heavy metals, lead (Pb) and mercury (Hg) are non-essential elements. Plants absorb these metals from soil, water and air through their roots and leaves. Heavy metals are the major environmental pollutants, which spread to soil through the use of pesticides, herbicides and micronutrient fertilizers, industrial effluents, decay of junk materials and sewage sludge, vehicular emissions, re-suspended road dust, diesel generator sets and coal-based thermal power plants. Sewage and sludge have contributed to heavy metal contamination of peri-urban lands and vegetable crops. The present review focuses on the effects of various concentrations of Hg on growth of young and mature seedlings as well as on nitrate reductase activity and nitrate assimilation in intact and excised seedling, especially the mechanism underlying nitrate reductase regulation by this heavy metal. Evidence indicates that mercury exerts significant adverse effects on the physiological activity of plants.     

Characterization and in vitro biological effects of ambient air PM10 from a rural,an industrial and an urban site in Sulaimani City,Iraq

Abstract

High urban atmospheric pollution is caused by economic and industrial growth, especially in developing countries. The objective of this study was to assess possible relationships between in vitro effects on human alveolar epithelial cells of source-related dust types collected at Sulaimani City (Iraq), and to determine their mineralogical and chemical composition. A passive sampler was used to collect dust particles at a rural, an industrial and an urban sampling site during July and August 2014. The samples were size-fractionated by a low-pressure impactor to obtain respirable dust with aerodynamic diameters of less than 10?µm. The dust was mainly composed of quartz and calcite. Chrysotile fibers (white asbestos) were also found at the urban site. Dust from the industrial and urban sites triggered cytotoxic and genotoxic effects in the cells, whereas only minor effects were observed for the sample from the rural site.     

Polycyclic aromatic hydrocarbons in household dust near diesel transport routes

A river-dredging project has been undertaken in Nantou, Taiwan. A large number of diesel vehicles carrying gravel and sand shuttle back and forth on the main roads. Ten stations along major thoroughfares were selected as the exposure sites for testing, while a small village located about 9 km from a main traffic route was selected as the control site. Levels of household dust loading at the exposure sites (60.3 mg/m²) were significantly higher than those at the control site (38.2 mg/m²). The loading (μg/m²) of t-PAHs (total polycyclic aromatic hydrocarbons) in the household dust at the exposure sites was significantly higher (P < 0.05) than was the case at the control site. The diagnostic ratios of PAHs showed that diesel emissions were the dominant source of PAHs at the exposure sites. The lack of a significant correlation between the concentrations of Fe and t-PAHs suggested that the t-PAHs in household dust might come from diverse sources. However, a significant correlation (P = 0.003) between the concentrations of Mo and t-PAHs implied that the most of the t-PAHs in the household dust might have resulted from diesel emissions. The lifetime cancer risks of BaP_eq from household dust exposure were markedly higher than those resulting from inhalation exposure.