微波无极灯：一种具有前景的高效光催化光源

微波无极灯具有制造容易、价格低廉、能耗小和光强大等优点.作为光催化氧化的光源时,由于微波的协同作用可有效提高光催化活性,并能简化反应器.从发光机理、微波协同作用、优缺点和影响因素等方面,对微波无极灯在光催化领域的研究进行详细阐述.     

微波辅助光催化降解高浓度活性黑

利用改装的家用微波炉、微波无极灯和TiO2催化剂研究了水中高浓度活性黑的光催化降解.系统考察了TiO2投加量、pH、微波无极灯数量对微波辅助光催化处理效果的影响,得出微波辅助光催化的最佳操作条件,并在最佳条件下对活性黑的脱色及矿化效果进行研究.结果表明,TiO2投加量存在最佳值2 g/L,降低pH和增加微波无极灯数量均可提高活性黑的降解率.在TiO2的投加量为2 g/L,pH =3,微波无极灯数量为3的最佳光催化条件下,400 mg/L的活性黑溶液反应180 min时可实现完全脱色,反应300 min时,TOC去除率高达89.1％.     

微波无极紫外碘灯净化低浓度挥发性有机物的研究

采用微波无极紫外碘灯,以乙酸丁酯为挥发性有机物(VOCs)的代表物,对微波无极紫外碘灯净化低浓度VOCs废气进行了连续流动态实验研究.结果表明,在微波电源功率为200 W、管道内气体流速为0.025 m/s(即停留时间为13.32 s时)、乙酸丁酯初始质量浓度为1.500mg/m3的情况下,乙酸丁酯降解率可达78％以上...     

微波无极紫外光催化降解茜素绿的性能研究及产物分析

以微波无极紫外灯为光源,P25型Ti O2为催化剂,研究了微波反应器中茜素绿(AG)的光催化降解性能,考察了染料初始浓度及p H对降解效率的影响,利用ESI电子喷雾质谱和离子色谱测定了茜素绿降解的中间产物,并对产物的可生化性进行了分析。结果表明,微波/紫外/二氧化钛体系拓宽了染料浓度和p H的适用范围。降解后生成了大量小分子物质,可生化性得到了大幅度的提高,BOD5/COD值从反应前的0.0959增加到了0.40。     

治理恶臭气体的新技术

传统处理恶臭气体的方法,有氧化法、吸附法、化学氧化法、生物法、低压汞灯分解法等,但均存在二次污染、处理效果不佳等缺陷。复旦大学环境科学研究所侯惠奇教授主持的“微波等离子体紫外辐射应用于处理恶臭物质的研究”课题,近日申请了两项国家发明专利,其研发的“无极紫外灯”采用频率为2．45MHz的微波放电,     

新型无极紫外灯的光氧化性能研究

本实验对新型无极紫外灯的发射光谱、不同波长光线在溶液中的传播、·OH和O3的生成量、活性艳红X-3B溶液的降解情况进行了测定,并与普通中压汞灯进行了比较.结果表明,无极紫外灯在紫外区光强约为相近功率的普通中压汞灯的20倍;在溶液中紫外光比可见光更易被吸收;·OH生成与溶液对短波长光子的吸收存在对应关系,本实验中无极紫外灯的最大氧化距离约为6 cm;O3的生成量随着空气曝气量或254 nm处的光强的增大呈指数增加;降解活性艳红X-3B溶液的过程符合负一级动力学关系,降解效果明显好于普通中压汞灯,并且证明了无极紫外灯与生成的臭氧在活性艳红X-3B的降解过程中存在协同作用.     

微波辅助光催化降解阿特拉津的表观动力学

以内分泌干扰物阿特拉津为目标物,建立循环流化床微波辅助光催化体系,研究其微波辅助光催化降解规律。表观动力学研究发现,当阿特拉津初始浓度较低时,其在微波辅助光催化体系中的降解符合表观一级反应动力学特征。降解反应速率常数与阿特拉津初始浓度呈负线性相关,与紫外光强呈正线性相关,与催化剂浓度呈抛物线性相关。表观反应速率常数kobs=3.95×10-4c-0.27030I1.2224W0.3283,该模型计算值与实验值吻合较好,平均相对偏差仅为0.5%,可用于预测微波辅助光催化降解低浓度有机污染物的反应规律。     

微波技术在污水处理中的研究进展和应用

微波技术因其独特的热效应和非热效应在水处理领域起着重要的作用。微波技术发展至今可分为4个方面:(1)微波直接辐射法处理污水;(2)微波场辅助活性炭处理污水;(3)微波与其他技术(光催化技术、金属催化剂等)联合应用处理污水;(4)微波辐照再生与制备催化剂。微波技术对各类污染物(如染料、氨氮废水、焦化废水和酚类、酸类和酯类等有机废水)的降解率影响显著。从降解效率的角度看,现代化微波工艺将朝着微波与高级氧化技术的联合应用方向发展,其联合反应机制和配套装置也有待做更多研究。     

TiO2晶体的微波水热法制备及光催化性能研究

以TiSO4和尿素为主要原料,EDTA为控制剂,采用微波水热法制备纳米TiO2光催化剂,并分析了纳米TiO2晶粒的最佳形成条件。利用XRD、TEM等技术对制备产物进行表征。结果表明,TiSO4和尿素混合物在微波水热条件下晶化150min后,产物为锐钛矿型TiO2,且产物粒径小、大小均匀。在紫外光照射下,以自制的锐钛矿型纳米TiO2为催化剂,酸性橙为降解目标物,进一步研究了其光催化性能。结果表明,该TiO2在紫外光照射下表现出稳定的光催化活性。     

无极紫外光降解染料活性艳红X-3B的研究

实验将一种新型光源--无极紫外灯,应用于染料废水的降解,考察了反应过程中,染料脱色率、TOC去除率、pH值以及反应前后高效液相色谱图谱的变化情况.实验表明,染料活性艳红X-3B经过无极紫外光处理110 min后,脱色率达96%,TOC去除率达66%,而pH值则是先降低后缓慢升高.     

Enhanced degradation of reactive brilliant red X-3B by photocatalysis integrated with micro-electrolysis

Environmental Science and Pollution Research - The microwave electrodeless lamp UV photocatalysis (MWUV) integrated with iron carbon micro-electrolysis (ME) was applied to degrade reactive...     

Photolysis of low concentration H2S under UV/VUV irradiation emitted from microwave discharge electrodeless lamps

The photolysis of simulating low concentration of hydrogen sulfide malodorous gas was studied under UV irradiation emitted by self-made microwave discharge electrodeless lamps (i.e. microwave UV electrodeless mercury lamp (185/253.7 nm) and iodine lamp (178.3/180.1/183/184.4/187.6/206.2 nm)). Experiments results showed that the removal efficiency (eta H2S) of hydrogen sulfide was decreased with increasing initial H2S concentration and increased slightly with gas residence time; H2S removal efficiency was decreased dramatically with enlarged pipe diameter. Under the experimental conditions with pipe diameter of 36 mm, gas flow rate of 0.42 standard l s(-1), eta H2S was 52% with initial H2S concentration of 19.5 mg m(-3) by microwave mercury lamp, the absolute removal amount (ARA) was 4.30 microg s(-1), and energy yield (EY) was 77.3 mg kW h(-1); eta H2S was 56% with initial H2S concentration of 18.9 mg m(-3) by microwave iodine lamp, the ARA was 4.48 microg s(-1), and the EY was 80.5mg kW h(-1). The main photolysis product was confirmed to be SO4(2-) with IC.     

微波辅助光催化降解水中酚的研究

利用改装的家用微波炉和自制的无电极灯(EDL)试验了5种酚在水溶液中的微波辅助光催化降解效果.结果表明,反应30 min,微波辅助光催化作用(MW/EDL/TiO2)能去除80%以上的苯酚、间硝基苯酚、对氯苯酚和对甲酚,相应溶液的总有机碳(TOC)均减少70%以上,2-萘酚的去除率为59%,溶液TOC减少54%;微波(MW或MW/TiO2)作用对酚的去除率有一定贡献;对上述5种酚的微波辅助光催化反应动力学进行了初步研究,发现均符合准一级动力学方程.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Application of photocatalysis as a post treatment method of a heterotrophic-autotrophic denitrification reactor effluent

The aim of this study is the application of photocatalysis as an effective post treatment scheme for the removal of the organic matter and bacteria released by an innovative biological denitrification process referred to as heterotrophic-autotrophic denitrification, which combines heterotrophic and autotrophic denitrification processes. Photocatalytic treatment was applied using TiO2 as a photocatalyst in the loading range of 0.25-2.00 g l(-1) for irradiation periods up to 60 min using a black light fluorescent lamp with an intensity of I(0)=1309 microW cm(-2). The photocatalytic inactivation data were modelled to pseudo first order kinetics as well as by the areal rates to evaluate the photocatalyst loading effect. Chlorination was used as a final disinfection step to attain an overall inactivation of total coliforms as well as to the formation of very low level of trihalomethanes.     

TiO2光催化氧化降解乳酸的工艺及机理研究

以TiO2为催化剂、紫外灯为光源对乳酸进行光催化降解实验,考察了乳酸初始浓度、TiO2用量、反应时间、曝气方式等因素对乳酸降解率的影响,并在此基础上应用正交实验对降解条件进行优化,同时对乳酸的降解机理进行了探索研究。实验结果表明：以300 W紫外汞灯为光源,在乳酸初始浓度为0.5 g/L、TiO2量为0.20 g/L、反应时间120 min、持续通入空气鼓泡的条件下,乳酸降解效果最佳,乳酸降解率为99.9%;降解12 h总有机碳去除率达91.2%。乳酸光催化降解的反应途径为：乳酸脱羧生成乙醇,乙醇被氧化生成乙醛,进而氧化为乙酸,所有的中间产物被继续降解,最终矿化为CO2和H2O等小分子物质。     

Decomposition of low-concentration gas-phase toluene using plasma-driven photocatalyst reactor

Plasma-driven photocatalysis system was prepared and performed. To overcome the treatment difficulty of volatile organic compounds, non-thermal plasma was used as a light source of photocatalysis. The removal of low-concentration toluene was investigated and secondary products were analyzed by gas chromatograph–mass spectroscopy. The plasma-driven photocatalyst reactor using direct current as a light source and titanium dioxide catalyst loaded on activated carbon fiber (TiO₂/ACF) as photocatalyst was studied. It was found that plasma-driven photocatalysis system could significantly increase the removal effect of toluene. The number of secondary products was largely decreased. It means that plasma-driven photocatalysis hybrid system was an effective method for the removal of volatile organic compounds.