Integrated geophysical surveys on waste dumps: evaluation of physical parameters to characterize an urban waste dump (four case studies in Italy).

Geophysical surveys were carried out on different waste dumps to evaluate key geometric and physical parameters. Depending on the dump dimensions and physical characteristics different geophysical techniques were used. Vertical electrical sounding, electrical resistivity tomography, induced polarization and seismic refraction techniques were integrated to eliminate the non-uniqueness of solutions and for a better understanding of the results. Physical parameters inside and outside the dumps were compared. The change of physical parameters such as resistivity, chargeability, and P-wave velocity allowed evaluation of waste dump geometry, leachate saturation levels, and thickness of waste. Furthermore, in illegal dumps, the size and waste type disposed could be evaluated. Calculated results were compared with plans and book-keeping from the dumps investigated.     

Development of a database of landfills and dump sites in Asian countries

This article briefly summarizes the limited landfill/dump information available for developing Asian countries, and introduces a database that aims to close the information gap through collecting and sharing data. Developing nations usually try to adapt the systems and technologies of developed countries. However, this approach may not be appropriate because of differences in socioeconomic, cultural, and political backgrounds. Many waste management projects fail after operations are transferred to local authorities owing to a lack of funds to cover the high operational expenses. Some successful projects have been adapted to local conditions, although the information on these successes is not often available for others. Nevertheless, only a few developing countries even have a national inventory of their dumps/landfills, and decision-makers have little awareness of the dumps and their impacts. The database introduced here will gather landfill/dump information from each country and organize it in a comparable format, and it will then be published on the Internet.     

LCA and economic evaluation of landfill leachate and gas technologies

Landfills receiving a mix of waste, including organics, have developed dramatically over the last 3-4 decades; from open dumps to engineered facilities with extensive controls on leachate and gas. The conventional municipal landfill will in most climates produce a highly contaminated leachate and a significant amount of landfill gas. Leachate controls may include bottom liners and leachate collection systems as well as leachate treatment prior to discharge to surface water. Gas controls may include oxidizing top covers, gas collection systems with flares or gas utilization systems for production of electricity and heat.The importance of leachate and gas control measures in reducing the overall environmental impact from a conventional landfill was assessed by life-cycle-assessment (LCA). The direct cost for the measures were also estimated providing a basis for assessing which measures are the most cost-effective in reducing the impact from a conventional landfill. This was done by modeling landfills ranging from a simple open dump to highly engineered conventional landfills with energy recovery in form of heat or electricity. The modeling was done in the waste LCA model EASEWASTE. The results showed drastic improvements for most impact categories. Global warming went from an impact of 0.1 person equivalent (PE) for the dump to −0.05 PE for the best design. Similar improvements were found for photochemical ozone formation (0.02 PE to 0.002 PE) and stratospheric ozone formation (0.04 PE to 0.001 PE).For the toxic and spoiled groundwater impact categories the trend is not as clear. The reason for this was that the load to the environment shifted as more technologies were used. For the dump landfill the main impacts were impacts for spoiled groundwater due to lack of leachate collection, 2.3 PE down to 0.4 PE when leachate is collected. However, at the same time, leachate collection causes a slight increase in eco-toxicity and human toxicity via water (0.007E to 0.013PE and 0.002 to 0.003 PE respectively). The reason for this is that even if the leachate is treated, slight amounts of contaminants are released through emissions of treated wastewater to surface waters.The largest environmental improvement with regard to the direct cost of the landfill was the capping and leachate treatment system. The capping, though very cheap to establish, gave a huge benefit in lowered impacts, the leachate collection system though expensive gave large benefits as well. The other gas measures were found to give further improvements, for a minor increase in cost.     

Transforming an open dump into a sanitary landfill: a development effort in waste management

Upgrading a crude dump site into a sanitary landfill is a very challenging task; Matuail landfill site in Dhaka posed just such a challenge. From the very beginning, the existing disposal site had been used for the crude dumping of solid wastes. All types of solid wastes were haphazardly disposed of all over the site. The existing drainage channels of the dumping ground were not operational due to blockage by indiscriminate waste dumping. A large amount of leachate oozing out from the waste mixed with storm water and made the site esthetically very displeasing and environmentally unsound. This adverse situation sometimes caused disruption of the waste vehicular movement. Step-by-step improvement measures have been taken in the open dump to make it controlled and sanitary by adopting simple and locally available materials, technical guidelines, and construction techniques.     

Report on waste dump sites around Bangalore

The present work aims at identifying, locating and quantifying the industrial and domestic waste dump sites located in and around Bangalore urban and rural districts of Karnataka state, India. Bangalore has a population of 6 million and has more than 2000 industries working at various industrial estates and other locations around the city. It was reported that about 1500 tons of municipal waste per day is being generated from Bangalore city. Studies reveal that there is no scientific treatment and disposal facility for scientific management of the waste generated. The waste from industries and community areas is disposed in an unscientific manner at several open dump sites across the city. There are more than 60 dump sites consisting of both municipal and industrial waste existing in and around Bangalore city; the locations are totally unhygienic. Based on the experience gained from field visits, physical observation of the waste disposed, quantity and nature of the waste disposed, each site was given with a grading based on polluting potential of the site. For selected sites, ground water samples were collected from nearby surface or bore wells and analysed for possible contamination. From the study, it was found that the site needed immediate attention and comes under severe impact category of 27 numbers and that of medium and low impact are 18 and 6 numbers, respectively. The disposal sites have got tremendous potential of spreading the epidemics/diseases to the people living in their immediate vicinity and at nearby places.     

The Ümraniye-Hekimbaşi open dump accident

The open dump of Ümraniye-Hekimbaşi was the main solid disposal site of the Asiatic side of Istanbul. At this site, which was in operation since 1976, 1500–2000 tonnes of solid wastes were disposed of daily. No waste compaction was undertaken during placement. The slope formed by the solid wastes was very steep (3 vertical to I horizontal), and recently demolition wastes were disposed of on top of these wastes. On 28 April 1993, an “explosion” took place, followed by the displacement of a large mass of solid wastes which engulfed II houses causing the death of 39 people. This paper investigates the possible reasons for this accident and concludes that it was caused by the initial sliding of the solid wastes, which were not deposited in a stable way, followed by an explosion of the methane generated and retained in the landfill.     

Open dumps in the Hellenic prefecture of Laconia: statistical analysis of characteristics and restoration prioritization on the basis of a field survey.

This study presents an assessment of the current status of open dumps in Laconia prefecture of Peloponnese in southern Greece, where all open dumps are targeted for closure by 2008. An extensive field survey was conducted in 2005 to register existing sites in the prefecture. The data collected included the site area and age, waste depth, type of disposed waste, distance from nearest populated area, local geographical features and observed practices of open burning and soil coverage. On the basis of the collected data, a GIS database was developed, and the above parameters were statistically analysed. Subsequently, a decision tool for the restoration of open dumps was implemented, which led to the prioritization of site restorations and specific decisions about appropriate restoration steps for each site. The sites requiring restoration were then further classified using Principal Component Analysis, in order to categorize them into groups suitable for similar restoration work, thus facilitating fund allocation and subsequent restoration project management.     

Slope failures in municipal solid waste dumps and landfills: a review

Between 1977 and 2005 six large-scale failures of municipal solid waste dumps and landfills have been recorded in the technical literature. The volumes of waste mobilized in the failures varied from 10-12 000 m(3) in a failure that killed nearly 300 people to 1.5 million m(3) in a failure that caused no deaths or injuries. Of the six failures, four occurred in dumps that, as far as is known, had not been subjected to any prior technical investigation of their shear stability. The remaining two failures occurred in engineer-designed landfills, one of which practised leachate recirculation, and the other co-disposed of liquid waste along with solid waste. The paper reviews, describes and analyses the failures and summarizes their causes.     

Soil properties and water regime of reclaimed surface dumps in the North Bohemian brown-coal region--a field study

This paper attempts to characterise the water regime of reclaimed surface dumps in connection with their soil physical properties. The results of a research project based on field measurements of moisture content and hydraulic conductivity, supported by analyses of undisturbed soil samples, led to recommendations regarding technological procedures for such dumps. A dielectric soil moisture meter, in an improved version, was successfully used for field monitoring and further evaluation of moisture content. Hydraulic conductivity was also measured in the field (by repeated borehole infiltration) using the Guelph permeameter method. Laplace-Gardner analysis was used for evaluating the field saturated hydraulic conductivity results.     

Evaluation of the mechanical properties of class-F fly ash

Coal-burning power plants in the United States (US) generate more than 70 million tons of fly ash as a by-product annually. Recycling large volumes of fly ash in geotechnical applications may offer an attractive alternative to the disposal problem as most of it is currently dumped in ponds or landfills. Class-F fly ash, resulting from burning of bituminous or anthracite coals, is the most common type of fly ash in the US. In the present study, the mechanical characteristics (compaction response, compressibility, and shear strength) of class-F fly ash were investigated by performing various laboratory tests (compaction test, one-dimensional compression test, direct shear test and consolidated-drained triaxial compression test) on fly ash samples collected from three power plants in the state of Indiana (US). Test results have shown that despite some morphological differences, class-F fly ash exhibits mechanical properties that are, in general, comparable to those observed in natural sandy soils.     

Application of recycled aggregate porous concrete pile (RAPP) to improve soft ground

In this study, a series of laboratory chamber tests was carried out to evaluate the applicability of a porous concrete pile fabricated with recycled aggregates for soft ground improvement. The recycled aggregate porous concrete pile (RAPP) has been developed to replace natural aggregates and to overcome technical problems associated with the conventional compaction piling systems. The laboratory chamber tests for evaluating the performance of RAPP were carried out with a cylindrical mold of 280?mm in internal diameter and 580?mm in height. A replacement area ratio of 5?% and three different loading steps were applied in the chamber tests. The experimental results of the surface settlement, excess pore pressure and vertical stress distribution versus time were compared with those of the sand compaction pile (SCP) reinforced composite ground under the same experimental condition. In addition, the experimental results were compared with the numerical simulation using ABAQUS. The current study shows that the settlement reduction in the RAPP-reinforced system is?significantly enhanced due to load transfer from the soil formation to the RAPP. Furthermore, the comparison of consolidation rates shows that the RAPP can also accelerate the consolidation of soft clay formation because the RAPP behaves as a vertical drain.     

Determination of specific gravity of municipal solid waste

This investigation was conducted to evaluate experimental determination of specific gravity (G_s) of municipal solid waste (MSW). Water pycnometry, typically used for testing soils was adapted for testing MSW using a large flask with 2000 mL capacity and specimens with 100–350 g masses. Tests were conducted on manufactured waste samples prepared using US waste constituent components; fresh wastes obtained prior and subsequent to compaction at an MSW landfill; and wastes obtained from various depths at the same landfill. Factors that influence specific gravity were investigated including waste particle size, compaction, and combined decomposition and stress history. The measured average specific gravities were 1.377 and 1.530 for as-prepared/uncompacted and compacted manufactured wastes, respectively; 1.072 and 1.258 for uncompacted and compacted fresh wastes, respectively; and 2.201 for old wastes. The average organic content and degree of decomposition were 77.2% and 0%, respectively for fresh wastes and 22.8% and 88.3%, respectively for old wastes. The G_s increased with decreasing particle size, compaction, and increasing waste age. For fresh wastes, reductions in particle size and compaction caused occluded intraparticle pores to be exposed and waste particles to be deformed resulting in increases in specific gravity. For old wastes, the high G_s resulted from loss of biodegradable components that have low G_s as well as potential access to previously occluded pores and deformation of particles due to both degradation processes and applied mechanical stresses. The G_s was correlated to the degree of decomposition with a linear relationship. Unlike soils, the G_s for MSW was not unique, but varied in a landfill environment due both to physical/mechanical processes and biochemical processes. Specific gravity testing is recommended to be conducted not only using representative waste composition, but also using representative compaction, stress, and degradation states.     

Geotechnical characterization of a Municipal Solid Waste Incineration Ash from a Michigan monofill

A field and laboratory geotechnical characterization study of a Municipal Solid Waste Incineration Ash disposed of at the Carleton Farms monofill in Michigan was performed. Field characterization consisted of field observations, collection of four bulk samples and performance of shear wave velocity measurements at two locations. Laboratory characterization consisted of basic geotechnical characterization, i.e., grain size distribution, Atterberg limits, specific gravity tests, compaction tests as well as moisture and organic content assessment followed by direct shear and triaxial shear testing. The test results of this investigation are compared to results in the literature. The grain size distribution of the samples was found to be very similar and consistent with the grain size distribution data available in the literature, but the compaction characteristics were found to vary significantly. Specific gravities were also lower than specific gravities of silicic soils. Shear strengths were higher than typically reported for sandy soils, even for MSWI ash specimens at a loose state. Strain rate was not found to impact the shear resistance. Significant differences in triaxial shear were observed between a dry and a saturated specimen not only in terms of peak shear resistance, but also in terms of stress–strain response. In situ shear wave velocities ranged from 500 to 800 m/s at a depth of about 8 m, to 1100–1200 m/s at a depth of 50 m. These high shear wave velocities are consistent with field observations indicating the formation of cemented blocks of ash with time, but this “ageing” process in MSWI ash is still not well understood and additional research is needed. An improved understanding of the long-term behavior of MSWI ash, including the effects of moisture and ash chemical composition on the ageing process, as well as the leaching characteristics of the material, may promote unbound utilization of the ash in civil infrastructure.     

Characterization and pilot‐scale studies for chemical oxidation remediation of fractured shale

The distribution of volatile organic compounds (VOCs) in fractured shale overlain by thin (< 10 feet) overburden at the Watervliet Arsenal near Albany, New York, was initially determined by sampling water from the fracture network using packer systems in boreholes and also using conventional monitoring wells. Furthermore, short‐term pumping and injection tests were conducted and the boreholes were logged using a variety of geophysical and hydrophysical tools. Tetrachloroethene is the dominant VOC in the groundwater, with lesser concentrations of trichloroethene and degradation products (cis‐1,2‐dichloroethene, trans‐1,2‐dichloroethene, and vinyl chloride). The vertical VOC distributions in the rock matrix were obtained from continuous‐cored holes from which small rock samples, collected at many depths between 18 and 150 feet below ground surface, were analyzed. The rock core VOC concentrations were determined by methanol extraction of crushed rock followed by direct methanol injection onto a gas chromatograph and subsequent estimation of rock porewater VOC concentrations. The rock core data support the concept that diffusion‐driven mass transfer has caused nearly all the VOC mass initially present in the fractures to now reside in the rock matrix, which has a porosity three or four orders of magnitude larger than the bulk fracture porosity. The results of the site characterization indicate that an effective site investigation strategy in fractured shale must include characterization of both the fracture and matrix contaminant distribution. These results also indicate that the most favorable remediation technologies for this fractured shale are those that will destroy VOCs in the rock matrix, particularly contaminants in the sorbed phase, and also destroy the VOC mass in the fractures including both dissolved and immiscible phases. The site characterization resulted in the selection of potassium permanganate for an in situ chemical oxidation pilot study. © 2004 Wiley Periodicals, Inc.     

Geoenvironmental behavior of foundry sand amended mixtures for highway subbases

The high cost of landfilling and the potential uses of waste foundry sands have prompted research into their beneficial reuse. Roadways have a high potential for large volume usage of the foundry sands. A laboratory testing program was conducted on soil-foundry sand mixtures amended with cement and lime to assess their applicability as highway subbase materials. The mixtures were compacted in the laboratory at a variety of moisture contents and compactive efforts and subjected to unconfined compression, California bearing ratio, and hydraulic conductivity tests. The environmental suitability of the prepared mixtures was evaluated by analyzing the effluent collected during hydraulic conductivity tests. Finally, required subbase thicknesses were calculated using the laboratory-based strength parameters. The results of the study show that the strength of a mixture is highly dependent on the curing period, compactive energy, lime or cement presence, and water content at compaction. The resistance of foundry sand-based specimens to winter conditions is generally better than that of a typical subbase reference material. Laboratory leaching tests indicated that if these mixtures later come in contact with water that has been discharged directly to the environment (e.g., drainage through asphalt pavement), the quality of water will not be affected.     

Leaching of heavy metals in acid mine drainage.

Acid mine drainage is one of the most serious environmental problems that the coal and metal mining industry is currently facing. The generation of low pH drainage enhances the dissolution of heavy metals in water. The samples used in this research originated from three pits at mine dumps. In a study reported in this paper, three types of tests; namely static test, kinetic test and column test were conducted to estimate acid generation and acid neutralization reaction rates, and to predict the solubility of metals and their release rates. Static test showed that all samples had a pH of net acid generation (NAG pH) <4, a net acid producing potential (NAPP) >10 kg H2SO4tonne(-1), and a S-content >3%, which can be classified as a high acid-forming capacity. Simulated runoff in the column tests was equivalent to 5-year average rainfall in Indonesia, the resultant leachates showed acidic behaviour (pH < 3.5). Based on the results, it was found that high mobilization of heavy metals (Cr, Cu, Zn, Cd and Pb) takes place under strong acidic conditions (pH approximately equal 2).     

Laboratory and field testing for utilization of an excavated soil as landfill liner material

This study investigates the feasibility of using a silty soil excavated in highway construction as landfill liner material. The tests were conducted both at laboratory and in situ scales, and the soil was tested in pure and lime treated forms. Different levels of compaction energy were used. For the field study, a test pad was constructed and in situ hydraulic conductivity experiments were conducted by sealed double ring infiltrometers (SDRI). Laboratory testing revealed that while lime treatment improved the shear strength, it resulted in higher hydraulic conductivity values compared to pure soil. It was observed that leachate permeation did not change the hydraulic conductivity of the pure and lime treated samples. Laboratory hydraulic conductivities were on the order of 10(-9) m/s and met the 1.0E-08 m/s criterion in the Turkish regulations, which is one order of magnitude higher than the value allowed in most developed countries. SDRI testing, which lasted for 6 mo, indicated that lime treatment increased the hydraulic conductivity of pure soil significantly in the field scale tests. In situ hydraulic conductivities were on the order of 1E-08 and 1E-07 m/s, and exceeded the allowable value in the Turkish regulations. Undisturbed samples collected from the test pad were not representative of field hydraulic conductivities. Contrary to laboratory findings, higher compaction efforts did not result in lower hydraulic conductivities in field scales. The study verified the importance of in situ hydraulic conductivity testing in compacted liners.     

A historical context of municipal solid waste management in the United States.

Municipal solid waste management (MSWM) in the United States is a system comprised of regulatory, administrative, market, technology, and social subcomponents, and can only be understood in the context of its historical evolution. American cities lacked organized public works for street cleaning, refuse collection, water treatment, and human waste removal until the early 1800s. Recurrent epidemics forced efforts to improve public health and the environment. The belief in anticontagionism led to the construction of water treatment and sewerage works during the nineteenth century, by sanitary engineers working for regional public health authorities. This infrastructure was capital intensive and required regional institutions to finance and administer it. By the time attention turned to solid waste management in the 1880s, funding was not available for a regional infrastructure. Thus, solid waste management was established as a local responsibility, centred on nearby municipal dumps. George Waring of New York City organized solid waste management around engineering unit operations; including street sweeping, refuse collection, transportation, resource recovery and disposal. This approach was adopted nationwide, and was managed by City Departments of Sanitation. Innovations such as the introduction of trucks, motorized street sweepers, incineration, and sanitary landfill were developed in the following decades. The Resource Conservation and Recovery Act of 1976 (RCRA), is the defining legislation for MSWM practice in America today. It forced the closure of open dumps nationwide, and required regional planning for MSWM. The closure of municipal dumps caused a 'garbage crisis' in the late 1980s and early 1990s. Private companies assumed an expanded role in MSWM through regional facilities that required the transportation of MSW across state lines. These transboundary movements of MSW created the issue of flow control, in which the US Supreme Court affirmed the protection of garbage under the Commerce Clause of the Constitution. Thus MSWM in America today is largely managed by municipalities, and operated by a relatively small number of private companies. It consists of a mixture of landfill, incineration, recycling, and composting, and is regulated under RCRA, the Clean Air Act and other related federal and state laws.     

Hydraulic properties and leachate level analysis of Kimpo metropolitan landfill, Korea

Hydraulic properties of waste and cover soil from Kimpo Metropolitan Landfill were experimentally measured by laboratory tests. The degree of compaction was changed to identify the effect on hydraulic conductivity, field capacity, and permanent wilting point. Properties were utilized in developing a reliable numerical tool for leachate analysis. HELP, a simulation model for hydrologic evaluation of landfill performance, was adopted for that purpose. For calibration, results from simulation using the parameter values measured by laboratory tests were compared against the field data. The model was applied to predict the leachate level change according to the degree of compaction and cover soil thickness variation. It was found that the increase in the degree of compaction for intermediate cover soil and waste results in the decrease of field capacity and hydraulic conductivity, hence, the increase of leachate level. The effect of cover layer thickness on the leachate level was minor. Based on the findings from laboratory and numerical experiments, a guideline for reclamation practice was recommended.