Formation of PCDDs and PCDFs during the combustion of polyvinylidene chloride

In laboratory-scale combustion of polyvinylidene chloride (PVDC) with a quartz tubular furnace designed and fabricated to provide the desired combustion temperature and mixing state of combustion gas with air, it was found that at 800 degrees C or higher the level of polychlorinated dibenzo-p-dioxins/polychlorinated dibenzofurans [corrected] (PCDDs/PCDFs) resulting from PVDC combustion was no higher than that from heating air alone, and thus far below the levels which resulted from PVDC combustion at 750 degrees C or lower. The results provide the first laboratory confirmation of the relation between PVDC incineration temperature and PCDD/PCDF formation, and of the primary importance of high temperature, turbulence for mixing between air and combustion gas, and sufficient residence time, as governing factors for the minimization of PCDD/PCDF formation in municipal solid waste incinerators.     

CuCl2-catalyzed PCDD/F formation and congener patterns from phenols

Homologue and isomer patterns of polychlorinated dibenzo-p-dioxin (PCDD) and polychlorinated dibenzofuran (PCDF) in CuCl2-catalyzed formation were studied in an isothermal flow reactor using a distribution of 20 phenols as measured in municipal waste incinerator (MWI) exhaust gases. A mixture of 20 phenols was synthesized and used as reactants for this study because phenols are known to be key precursors in the formation of PCDD/F. Experiments were conducted at 400 degrees C. The 92% of nitrogen (N2) and 8% of oxygen (O2) were used as a carrier gas. PCDD/F homologue and isomer patterns with dibenzo-p-dioxin (DD) and dibenzofuran (DF) were obtained from a mixture of 20 phenols. DF+PCDF formation was favored over DD+PCDD formation. The major homologue groups formed were non-chlorinated DD and DF, and PCDD/F homologue fraction decreased with the degree of chlorination. PCDD/F homologue and isomer distributions were almost constant. Phenol and lower chlorinated phenols present in high amount played an important role in PCDD/F congener distributions. The results presented here can be used as characteristics or fingerprints for homologue and isomer patterns of PCDD/F formation attribution in CuCl2-catalyzed reaction from phenols.     

Source identification of PCDD/Fs in agricultural soils near to a Chinese MSWI plant through isomer-specific data analysis

Isomer-specific data were investigated in order to identify the sources of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in agricultural soils, including Fluvo-aquic and paddy soils, in the vicinity of a Chinese municipal solid waste incineration (MSWI) plant. Homologue and isomer profiles of PCDD/Fs in soils were compared with those of potential sources, including combustion sources, i.e., MSWI flue gas and fly ash; and the impurities in agrochemicals, such as the pentachlorophenol (PCP), sodium pentachlorophenate (PCP-Na) and 1,3,5-trichloro-2-(4-nitrophenoxy) benzene (CNP). The results showed that the PCDD/F isomer profiles of combustion sources and agricultural soils were very similar, especially for PCDFs, although their homologue profiles varied, indicating that all the isomers within each homologue behave identically in the air and soil. Moreover, factor analysis of the isomer compositions among 33 soil samples revealed that the contamination of PCDD/Fs in agricultural soils near the MSWI plant were primarily influenced by the combustion sources, followed by the PCP/PCP-Na and CNP sources. This implication is consistent with our previous findings based on chemometric analysis of homologue profiles of soil and flue gas samples, and identifies PCP/PCP-Na as an additional important source of PCDD/Fs in the local area. This makes the similarities and differences of isomer profiles between Fluvo-aquic and paddy soils more explainable. It is, therefore, advisable to use isomer-specific data for PCDD/F source identifications where possible.     

Thermodynamic analysis and kinetic modelling of dioxin formation and emissions from power boilers firing salt-laden hog fuel

Both organic chlorine (e.g. PVC) and inorganic chlorides (e.g. NaCl) can be significant chlorine sources for dioxin and furan (PCDD/F) formation in combustion processes. This paper presents a thermodynamic analysis of high temperature salt chemistry. Its influence on PCDD/F formation in power boilers burning salt-laden wood waste is examined through the relationships between Cl2, HCl, NaCl(g) and NaCl(c). These analyses show that while HCl is a product of combustion of PVC-laden municipal solid waste, NaCl can be converted to HCl in hog fuel boilers by reactions with SO2 or alumino-silicate materials. Cl2 is a strong chlorinating agent for PCDD/F formation. HCl can be oxidized to Cl2 by O2, and Cl2 can be reduced back to HCl by SO2. The presence of sulphur at low concentrations thus enhances PCDD/F formation by increasing HCl concentrations. At high concentrations, sulphur inhibits de novo formation of PCDD/Fs through Cl2 reduction by excess SO2. The effect of NH3, CO and NOx on PCDD/F formation is also discussed. A semi-empirical kinetic model is proposed. This model considers both precursor and de novo formation mechanisms. A simplified version is used as a stack emission model. The kinetic model indicates that stack dioxin emissions will increase linearly with decreasing electrostatic precipitator (ESP) efficiency and exponentially with increasing ESP temperature.     

Formation and transport of PCDD/Fs in the packed bed of soil containing organic chloride during a thermal remediation process

The authors previously proposed the concept of a new thermal remediation process for particulate/powder materials contaminated by polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and experimentally verified its validity on the basis of process efficiency. However, contaminees such as soils and fly ashes from waste incinerators often contain a considerable amount of other chlorides, which may act as a main source of chlorine in the formation of PCDD/Fs via thermal processes. The present study aims to examine the formation and transport of PCDD/Fs in the packed bed of soil containing a chloride during the process. Polyvinyl chloride (PVC) polymer was mixed with soil sample as an organic chloride model. A laboratory-scale apparatus was employed as a process simulator. Further, a technique to quench the process was applied to observe the concentration distribution of PCDD/Fs in the solid bed in the vertical direction. The result shows that the PCDFs tend to form dominantly in the high temperature (calcination and/or combustion) zone and are successively trapped in the low temperature (wet) zone. Especially, TeCDF is the most dominant homologue contained in the wet zone and outlet gas. Although PCDD/Fs are once trapped at the wet zone, the concentration of the remediated materials gives fairly low value (1.9 pg/g-dry, 0.04 pg-TEQ/g-dry). It signifies that organic chlorides mingled in the solid contaminee not affect the removal efficiency of PCDD/Fs in the process. Nevertheless, attention should be paid to the potential emission of PCDD/Fs in the outlet gas due to the presence of organic chloride in the soil.     

Assessment of emissions and removal of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) at start-up periods in a hazardous waste incinerator

A study was conducted to observe the changes in polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/F) levels and congener profiles in the flue gas of a hazardous waste incinerator during two start-up periods. Flue gas samplings were performed simultaneously through Air Pollution Control Devices (APCDs) (including boiler outlet, electrostatic precipitator (ESP) outlet, wet scrubbers (WS) outlet, and activated carbon (AC) filter outlet) in different combustion temperatures during a planned cold (long) start-up and an unplanned warm (short) start-up. The results showed that PCDD/F concentrations could be elevated during the start-up periods up to levels 3–4 times higher than those observed in the normal operation. Especially lower combustion temperatures in the short start-ups may cause high PCDD/F concentrations in the raw flue gas. Assessment of combustion temperatures and Furans/Dioxins values indicated that surface-catalyzed de novo synthesis was the dominant pathway in the formation of PCDD/Fs in the combustion units. PCDD/F removal efficiencies of Air Pollution Control Devices suggested that formation by de novo synthesis existed in ESP also when in operation, leading to increase of gaseous phase PCDD/Fs in ESP. Particle-bound PCDD/Fs were removed mainly by ESP and WS, while gaseous phase PCDD/Fs were removed by WS, and more efficiently by AC filter.

Implications: This paper evaluates PCDD/F emissions and removal performances of APCDs (ESP, wet scrubbers, and activated carbon) during two start-up periods in an incinerator. The main implications are the following: (1) start-up periods increase PCDD/F emissions up to 2–3 times in the incinerator; (2) low combustion temperatures in start-ups cause high PCDD/F emissions in raw gas; (3) formation of PCDD/Fs by de novo synthesis occurs in ESP; (4) AC is efficient in removing gaseous PCDD/Fs, but may increase particle-bound ones; and (5) scrubbers remove both gaseous and particle-bound PCDD/Fs efficiently.     

Suppressing effect of goethite on PCDD/F and HCB emissions from plastic materials incineration

Polyethylene (PE) and polyvinyl chloride (PVC) are the leading plastics in total production in the world. The incineration of plastic-based materials forms many chlorinated compounds, such as polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs). In this study the addition of goethite (alpha-FeOOH) was investigated to determine its suppressing effect on the emission of PCDD/Fs and hexachlorobenzene (HCB) during the combustion of wastes containing PE and PVC. Goethite was being considered since it acts as a dioxin-suppressing catalyst during incineration. Results showed that incorporation of goethite greatly reduced the generation of PCDD/Fs and HCB in the exhaust gas and fly ash. The concentration of PCDD/Fs in flue gas decreased by 45% for lab-scale and 52% for small incinerator combustion experiments, where the goethite ratios in feed samples were 0.54% and 0.34%, respectively. Under the same conditions, the concentration of HCB in flue gas decreased by 88% and 62%, respectively. The present study showed a possible mechanism of the suppressing effect of the goethite for PCDD/F formation. It is likely that iron chlorides react with particulate carbon to form organo-chlorine compounds and promote PCDD/F formation in the gas phase. XRD analysis of combustion ash revealed that the goethite was partially dehydrated and converted to alpha-Fe(2)O(3) and Fe(3)O(4) but no iron chlorides formation. Therefore the goethite impregnated plastics can contribute the reduction of PCDD/Fs and HCB in the exhaust gas during incineration of MSW.     

Formation behavior of PCDD/Fs in PVC pyrolysis with copper oxide

Formation and decomposition behaviors of PCDD/Fs during pyrolysis of polyvinyl chloride (PVC) with CuO have been investigated. These reactions proceed simultaneously, and the rate of decomposition exceeds that of formation with further retention. More 2,3,7,8-TCDD is formed when the dechlorination of PCDD/Fs proceeds significantly. Homologue profile patterns of PCDD/Fs show that the fractions of O8CDD and H6CDFs are relatively larger within PCDDs and PCDFs, respectively. Extremely large amounts of PCDD/Fs are obtained with the long retention time at 200 degrees C. The formation of PCDD/Fs decreases drastically with increase in the molar ratio of CuO/PVC. The acceptability of thermodynamic calculations on the formation of PCDD/Fs is also investigated. The thermodynamic calculated tendency of the effect of oxygen on the formation of PCDD/Fs agrees well with the experimental results, although absolute values of the amount of PCDD/Fs are much different.     

Distribution characteristics and source analysis of dioxins in sediments and mussels from Qingdao coastal sea

Seven of surface sediments, one sediment core and two mussel samples were collected from the Qingdao coastal sea of the western Yellow Sea and analyzed to determine the horizontal distribution, deposition flux, and toxicity equivalency (TEQs) of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). The total PCDD/Fs concentrations in the surface sediments ranged between 10.7 and 428 ng kg(-1) dry wt. The horizontal distribution of PCDD/F congeners in the sediments was characterized by elevated concentrations at the locations in the east of Jiaozhou Bay with the highest concentration occurring near the Haibo River mouth. Physical parameters (total organic carbon contents and sediment types) and the current circulation systems in Jiaozhou Bay can be important factors controlling the horizontal distribution pattern of PCDD/Fs in the bay. The influence of the Haibo River as a source of pollution was evidenced by PCDD/F homologue profiles, indicating a contribution from sewage sludge in addition to other possible sources. Records from the sediment core revealed that the total PCDD/Fs in the Qingdao coastal sea were nearly constant since 1951 till 1980s and increased remarkably after 1980s. The total 2,3,7,8-substituted PCDD/Fs and total TEQs of PCDD/Fs on the lipid basis in the mussel sample inside the bay were significantly higher than in the adjacent sediment. The homologue profiles of PCDD/Fs in the mussels were quite different from those of the sediments, characterized by high TCDF (50% of the total PCDD/Fs).     

Effect of copper chloride on the emissions of PCDD/Fs and PAHs from PVC combustion

The influences of temperature, air flow and the amount of copper chloride upon the types and amount of the toxic emissions such as polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) and polycyclic aromatic hydrocarbons (PAHs) during combustion of polyvinyl chloride (PVC) were investigated. The mechanism concerning the effect of temperature and copper chloride on the PCDD/Fs and PAHs formation was discussed. The results shown that without copper chloride, trace amounts of PCDD/Fs and large amounts of PAHs were found in the emissions from the pure PVC combustion under various combustion conditions. The addition of copper chloride enhanced PCDD/Fs formation, but it seems that the formation of PAHs decreased with increasing amount of copper chloride, and greater total amount of PAHs were produced at the higher temperature under our experimental conditions.     

Ambient air monitoring of PCDD/Fs and co-PCBs in Gyeonggi-do, Korea

We started the monitoring for PCDD/Fs in ambient air and soil in August 2001, and co-PCBs in January 2002. Decreasing of PCDD/Fs and co-PCBs levels in ambient air were observed. The higher PCDD/Fs levels were found in winter and lower in autumn. We found that the industrial incinerators influenced the PCDD/Fs levels in ambient air. In the 2,3,7,8-substituted PCDD/Fs concentration profiles, the three major congeners occupied 67% of the total mass. In case of co-PCBs, PCB#118, #105 and #77 were observed as the main congeners. Five cluster groups discriminated by ratio of four components, O(8)CDD, 1,2,3,4,6,7,8-H(7)CDD, 1,2,3,4,6,7,8-H(7)CDF and O(8)CDF, were obtained from HCA (hierarchical cluster analysis).     

Atmospheric bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in the vicinity of an iron and steel making plant

An IRA-743 resin bulk sampler was validated to monitor long-term bulk deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). Six consecutive sampling campaigns (2008-2009) were conducted at four sites around steel complexes in Pohang, South Korea to investigate spatial and seasonal variations of PCDD/F bulk deposition. The bulk deposition within the steel complex showed the highest ∑_4-8PCDD/F (Tetra-Octa) fluxes, ranging from 204 to 608 (mean: 352) pg m⁻² d⁻¹, indicating steel complexes were major sources of PCDD/Fs. The homologue profiles were dominated with lower chlorinated PCDFs. Furthermore, the prevailing winds were confirmed to influence the spatial distribution of PCDD/F deposition. There were apparent seasonal variations of the bulk deposition at each site, and seasonal homologue patterns of PCDD/Fs were clearly observed. According to the passive air sampling, however, no significant seasonal change of ambient air concentrations of PCDD/Fs was observed. Therefore, it was concluded that the seasonal variations of deposition fluxes of PCDD/Fs probably resulted from temperature-dependent gas/particle partitioning.     

Influence of combustion conditions on the PCDD/F-, PCB-, PCBz- and PAH-concentrations in the post-combustion chamber of a waste incineration pilot plant

Experiments at a pilot scale waste incinerator (0.5 MW thermal power) showed that the conditions in the post-combustion chamber (650-900 degrees C) are strongly influencing the formation of chlorinated and non-chlorinated aromatics. Non-optimal combustion conditions resulted in increased concentrations of mono- to trichlorinated dibenzo-p-dioxins (PCDD), dibenzofurans (PCDF) and polycyclic aromatic hydrocarbons (PAH), while chlorinated benzenes (PCBz), polychlorinated biphenyls (PCB) and the higher chlorinated PCDD/F are only weakly affected or even decrease. The changes in concentration of the compounds investigated over a time span of hours gave hints on 'memory effects' in this combustion zone. For mono- and dichlorinated benzenes, a high correlation (r2 = 0.80) with the international toxicity equivalent (I-TEQ) value of PCDD/F was observed. As recently has been demonstrated, this correlation can be utilized for an indirect on-line measurement of the I-TEQ by a novel laser mass spectrometric technique (REMPI-TO-FMS).     

Thermal degradation of 2-chlorophenol promoted by CuCl2 or CuCl: formation and destruction of PCDD/Fs

The oxidative degradation of 2-chlorophenol in air (equivalence ratio phi=0.8) was investigated at 350 degrees C by using the sealed tube technique under different conditions: in the gas phase and in the presence of copper chlorides (CuCl2 and CuCl in different proportions). Not only PCDD/Fs but carbon oxides and other organic products such as chlorophenols, chlorobenzenes, tetrachloroethylene and tetrachlorocyclopentenedione were quantified in order to evaluate the relative importance of reaction pathways. Additional experiments were performed to analyse the degradation products of octachlorodibenzodioxin and 2-monochlorodibenzodioxin. Although it was stated that chlorobenzenes could be formation precursors for PCDD/Fs, experimental data obtained in this work show that chlorobenzenes can also be degradation products of PCDD/Fs.     

Influence of metal oxides on PCDD/Fs formation from pentachlorophenol

Chlorophenols (ClPhs) are considered as important precursors for PCDD/Fs formation. The influences of series of metal oxides including MgO, Al2O3, CaO, BaO, TiO2, V2O5, MnO2, Fe2O3, Co3O4, CuO, Ag2O, ZnO, HgO, SnO, PbO, La2O3, CeO2, and Eu2O3 on PCDD/Fs formation from pentachlorophenol (PCP) were investigated in a laboratory-scale reactor. The results indicated that most of the above metal oxides have obvious suppressing effects on the total amount of PCDD/Fs formation from precursor PCP except for CuO, ZnO, MnO2, TiO2 and Co3O4 with promotion effects at 280 degrees C for 2 h. Although MgO, Al2O3, Fe2O3, PbO, La2O3 and Eu2O3 could reduce the amount of octachlorinated dibenzo-p-dioxin (OCDD), they promote the formation of more toxic 1,2,3,4,6,7,8-HpCDD at the same time. The total suppressing efficiencies of several metal oxides including CaO, BaO, PbO, Ag2O, HgO and SnO which have lower Z/r (charge to radius ratio) <2 are all over 90%. The theories of generalized acid-base and atomic parameter (Z/r) were used to speculate the effecting mechanisms. The factors including time and temperature on suppressing efficiencies of CaO, BaO and PbO have also been studied in the present paper. The results showed that the total suppressing efficiencies of CaO, BaO and PbO increase with the increase of heated time and temperature.     

PCDD/Fs and PCBs in airborne particulate matter of the greater Thessaloniki area, N. Greece

Particle-bound polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polychlorinated biphenyls (PCBs) were monitored at two sites in northern Greece for an eight-month period in 1999. PCDD/F concentrations were close to the lower end of reported values worldwide. Excepting a few cases, the PCDD/Fs homologue profile was stable. The gaseous PCDD/F fractions calculated were found to account for a small percentage of the total concentrations (<2% for OCDD/Fs and HpCDD/Fs, while 30-35% for TCDFs). Particle-bound PCBs were also found at low concentrations which, however, were higher at the urban site. Calculations of the dry deposition of particulate PCDD/ Fs and PCBs gave mean values of 0.52 and 0.59 pg I-TEQ/m2/day of PCDD/Fs, while 242 and 74 pg/m2/day of sigmaPCBs for the urban and the semirural areas respectively. An anticorrelation of PCDD/F concentrations with ambient temperature was derived particularly for the lower chlorinated congeners. A weak association with winds of western and southern origin was also observed. Factor analysis and literature source profiles were employed to identify possible emission sources. It was appeared that the PCDD/F compositional pattern of TSP is influenced by mixed sources the most prominent being uncontrolled fires and car exhausts.     

Formation of aromatic chlorinated compounds catalyzed by copper and iron

This study shows the catalyzing effects of iron and copper on the formation of chlorinated compounds such as chlorobenzenes (ClBzs), chlorophenols (CIPhs), polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). Both total concentrations and congener distributions have been studied. The parameters and conditions varied during the combustion tests were the complete and incomplete combustion and the metal and chlorine addition. The incomplete combustion promoted the formation of organic chlorinated compounds in flue gas particles. Highly chlorinated congeners of PCDD/F were dominant in the flue gas particles, whereas the importance of lower chlorinated congener were increased in the gas phase. In the complete combustion conditions the concentrations of PCDD/Fs increased when the degree of chlorination were high, nevertheless the concentrations of tetra and penta PCDD/Fs were higher in the gas phase than the concentrations in the fly ash particles. Organic chlorine promoted the formation of chlorinated compounds more effectively than inorganic chlorine, which instead promoted the formation of PCDD/Fs in the gas phase, especially with copper catalyst. Different concentration levels of chlorinated compounds were observed in the gas phase and in particles when the chlorine source and combustion conditions were varied from incomplete to optimum conditions. Both copper and iron seem to have a catalytic effect on PCDD/F formation.     

Increased PCDD/F formation in the bottom ash from fires of CCA-treated wood

Bottom ash that was the result of the combustion of chromated copper arsenate (CCA) treated wood under controlled fire conditions showed an increase of several orders of magnitude in the levels of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), compared to that of untreated timber. Wood that has been pressure treated with CCA contains copper (II), which is known to catalyse the so-called de novo formation of PCDD/Fs. Comparable levels of PCDD/Fs would be expected in residual ash from burning CCA-treated wood in backyard fires, stoves and wood heaters, as a consequence of similar combustion conditions.     

Influence of variation in the operating conditions on PCDD/F distribution in a full-scale MSW incinerator

Optimizing the operating parameters to minimize polychlorodibenzo-p-dioxins and polychlorodibenzofurans (PCDD/F) emission is the common interest of the municipal solid waste (MSW) incineration industry. In this study, we investigated the distribution of tetra- to octa-CDD/F along the flue gas line in a full-scale reciprocating grate incinerator and evaluated the effects of temperature control and O(2) level on PCDD/F formation. Six runs were laid out and all performed under sufficient burning conditions, in which the combustion efficiency of MSW was more than 99.9%. The total concentration of tetra- to octa-CDD/F measured at the boiler outlet showed an increasing tendency with the increase of boiler outlet temperature (T(B)) from 214 degrees C to 264 degrees C. When flue gas ran across the semi-dry scrubber and cyclone precipitator, in which the temperature varied from 264 degrees C to 162 degrees C, the concentrations of the lower chlorinated dioxins and furans were significantly raised, especially for the TCDF. Increasing O(2) supply from 6.0% to 10.5% essentially led to a higher yield of tetra- to octa-PCDD/F, suggested that under sufficient burning conditions the lower O(2) level was favorable for reducing PCDD/F formation and emission. The variation of O(2) level did not give rise to a systematical change of PCDD/F homologue pattern. For all measurements, the isomer distributions of tetra- to hepta-PCDD/F were more or less the same, nearly independent of variations in the operating conditions and sampling positions. Only the significant increase of the sum of 1,3,7,8-TCDF and 1,3,7,9-TCDF was found in the zone after the boiler section.     

Effect of liquid inhibitors on PCDD/F formation. Prediction of particle-phase PCDD/F concentrations using PLS modelling with gas-phase chlorophenol concentrations as independent variables

Emissions of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) from municipal waste incineration are currently a subject of considerable public concern because of their extreme toxicity. PCDD/F formation in incineration processes is being studied widely, but little work has been done on their inhibition. We studied the effect of two liquid inhibitors, sodium ammonium hydrogen phosphate (NAHF) and urea (H2NCONH2), on PCDD/F formation in the combustion of liquid fuel doped with copper and chlorine using a pilot-scale plant. The inhibitors were injected into the flue gas stream at a temperature of 725 degrees C, whereupon both the chlorophenol and PCDD/F concentrations decreased. Particle-phase PCDD/F concentrations in particular decreased by up to 90% with NAHF and 70% with urea, but gas phase reduction took place only with urea. The results suggest that the formation of PCDD/Fs is hindered in the particle phase at the early stages of the PCDD/F formation chain, probably even before precursors such as chlorophenols have been formed. As a consequence, particle-phase PCDD/F concentrations can be predicted by a PLS (partial least-squares) approach with the gas-phase chlorophenol concentrations as independent variables. The structure and partial charges of Cu(+)-urea complex were calculated by the HF/3-21G basis set.