Simultaneous removal of nitrate and pentachlorophenol from simulated groundwater using a biodenitrification reactor packed with corncob

Both nitrate and pentachlorophenol (PCP) are familiar pollutants in aqueous environment. This research is focused on the simultaneous removal of nitrate and PCP from simulated contaminated groundwater using a laboratory-scale denitrification reactor packed with corncob as both carbon source and biofilm support. The reactor could be started up readily, and the removal efficiencies of nitrate and PCP reached up to approximately 98 % and 40–45 % when their initial concentrations were 50 mg N/L and 5 mg/L, respectively, after 15-day continuous operation at 10 h of hydraulic retention time (HRT) and 25 °C. Approximately 91 % of PCP removal efficiency was achieved, with 2.47 mg/L of chloride ion release at 24 h of HRT. Eighty-two percent of chlorine in PCP removed was ionized. The productions of 3-chlorophenol and phenol and chloride ion release indicate that the reductive dechlorination reaction is a major degradation pathway of PCP under the experimental conditions.     

Short-chain chlorinated paraffins (SCCPs) in surface soil from a background area in China: occurrence, distribution, and congener profiles

Short-chain chlorinated paraffins (SCCPs) are extremely complex technical mixtures of polychlorinated n-alkanes with carbon chain lengths from C₁₀ to C₁₃ and chlorine content between 49 and 70 %. SCCPs are under consideration for inclusion in the Stockholm Convention on persistent organic pollutants. SCCPs have been used extensively in industrial production, but little is known about the pollution level in soil environment in China. In this study, levels and distribution of SCCPs in soil samples from Chongming Island were analyzed. Concentrations of total SCCPs in soil samples ranged from 0.42 to 420 ng?g^?1, with a median of 9.6 ng?g^?1. The ubiquitous occurrence of SCCPs in Chongming Island implied that long-range atmospheric transport and soil–air exchange may be the most important pathways for SCCP contamination in the background area. The localized SCCP contamination could be derived from an unidentified source. Hierarchical cluster analysis indicated that C₁₃- and C₁₁-congeners were predominant in most soils and C₁₀- and C₁₂-congeners dominated in the remaining soils. Cl₇- and Cl₈-congeners were on the average the most dominant chlorine congeners in nearly all soils. Principal component analysis suggested that the separation of even and odd carbon chain congeners occurred during long-range atmospheric transport and aging in soil in the study area.     

Historical record of mercury contamination in sediments from the Babeni Reservoir in the Olt River,Romania

Background, aim and scope

Mercury (Hg) is a ubiquitous and hazardous contaminant in the aquatic environment showing a strong biomagnification effect along the food chain. The most common transfer path of Hg to humans is contaminated fish consumption. In severely exposed humans, Hg poisoning may lead to damage in the central nervous system. Thus, it is important to examine current and past contamination levels of Hg in aquatic milieu. The Olt River is the largest Romanian tributary of the Danube River. The use of Hg as an electrode in a chlor-alkali plant contributed to the contamination of the aquatic environment in the Rm Valcea region. The purpose of this study was to compare the current state of Hg contamination with the past contamination using a historical record obtained from a dated sediment core from one of the Olt River reservoirs (Babeni) located downstream from the chlor-alkali plant. To our knowledge, no published data on Hg contamination in this region are available. The Babeni Reservoir was selected for this study because it is situated downstream from the chlor-alkali plant, whilst the other reservoirs only retain the pollutants coming from the upstream part of the watershed. Preliminary analyses (unpublished) showed high Hg concentrations in the surface sediment of the Babeni Reservoir. One core was taken in the upstream Valcea Reservoir to provide a local background level of Hg concentrations in sediments.

Results and discussion

Sediment texture was uniform in the cores from both reservoirs. Laminated sediment structure, without any obvious discontinuities, was observed. Hg concentrations in the sediment core from the Valcea Reservoir were low and constant (0.01–0.08 mg/kg). In Babeni Reservoir sediments, Hg concentrations were very high in the deeper core section (up to 45 mg/kg in the longest core) and decreased to lower concentrations toward the top of the cores (1.3–2.4 mg/kg). This decrease probably reflects technological progress in control of emissions from the Hg-cell-based chlor-alkali industry. Two strong peaks could be distinguished in older sediments. The mean rate of sedimentation (5.9 cm/year) was calculated from the depth of the ¹³⁷Cs Chernobyl peak. This was in good agreement with the sedimentation rate estimated at this site from a bathymetric study. Assuming a constant sedimentation rate, the two Hg peaks would reflect two contamination events in 1987 and 1991, respectively. However, it is also possible that the two peaks belong to the same contamination event in 1987 but were separated by a sediment layer richer in sand and silt. This layer had a low Hg concentration, which can be interpreted as a mass deposition event related to a major flood bringing Hg-free sediments.

Conclusions

Whilst the chlor-alkali plant partly switched to a cleaner technology in 1999, no obvious decrease of Hg concentrations was observed in recent decade. Results from the sediment core reflected the historical trend of Hg release from the chlor-alkali plant, revealed important contamination episodes and confirmed a legacy of contamination of Hg in recent sediments even if the concentrations of Hg decreased toward the surface due to a more efficient emission control.

Recommendations and perspectives

Although the Hg concentrations in Babeni Reservoir sediments were extremely high in the late eighties and they remain one order of magnitude higher in the surface sediments than in sediments from the upstream reservoir, little is known about the transfer of Hg to the biota and human population. Our initial measurements indicate the presence of monomethyl-Hg (MMHg) in pore water, but further studies are necessary to evaluate fluxes of MMHg at the sediment–water interface. Samples of fish and hair from various groups of the local population were recently collected to evaluate the potential hazard of Hg contamination to human health in the Rm Valcea region.

     

Assessment of natural sepiolite on cadmium stabilization, microbial communities, and enzyme activities in acidic soil

A pot trial was conducted to assess the efficiency of sepiolite-induced cadmium (Cd) immobilization in ultisoils. Under Cd concentrations of 1.25, 2.5, and 5 mg?kg^?1, the available Cd in the soil after the application of 1–10 % sepiolite decreased by a maximum of 44.4, 23.0, and 17.0 %, respectively, compared with no sepiolite treatments. The increase in the values of soil enzyme activities and microbial number proved that a certain metabolic recovery occurred after sepiolite treatment. The dry biomass of spinach (Spinacia oleracea) increased with increasing sepiolite concentration in the soil. However, the concentration (dry weight) of Cd in the spinach shoots decreased with the increase in sepiolite dose, with maximum reduction of 92.2, 90.0, and 84.9 %, respectively, compared with that of unamended soils. Under a Cd level of 1.25 mg?kg^?1, the Cd concentration in the edible parts of spinach at 1 % sepiolite amendment was lower than 0.2 mg?kg^?1 fresh weight, the maximum permissible concentration (MPC) of Cd in vegetable. Even at higher Cd concentrations (2.5 and 5 mg?kg^?1), safe spinach was produced when the sepiolite treatment was up to 5 %. The results showed that sepiolite-assisted remediation could potentially succeed on a field scale by decreasing Cd entry into the food chain.     

Historical record of mercury contamination in sediments from the Babeni Reservoir in the Olt River,Romania

Background, aim and scope

Mercury (Hg) is a ubiquitous and hazardous contaminant in the aquatic environment showing a strong biomagnification effect along the food chain. The most common transfer path of Hg to humans is contaminated fish consumption. In severely exposed humans, Hg poisoning may lead to damage in the central nervous system. Thus, it is important to examine current and past contamination levels of Hg in aquatic milieu. The Olt River is the largest Romanian tributary of the Danube River. The use of Hg as an electrode in a chlor-alkali plant contributed to the contamination of the aquatic environment in the Rm Valcea region. The purpose of this study was to compare the current state of Hg contamination with the past contamination using a historical record obtained from a dated sediment core from one of the Olt River reservoirs (Babeni) located downstream from the chlor-alkali plant. To our knowledge, no published data on Hg contamination in this region are available. The Babeni Reservoir was selected for this study because it is situated downstream from the chlor-alkali plant, whilst the other reservoirs only retain the pollutants coming from the upstream part of the watershed. Preliminary analyses (unpublished) showed high Hg concentrations in the surface sediment of the Babeni Reservoir. One core was taken in the upstream Valcea Reservoir to provide a local background level of Hg concentrations in sediments.

Results and discussion

Sediment texture was uniform in the cores from both reservoirs. Laminated sediment structure, without any obvious discontinuities, was observed. Hg concentrations in the sediment core from the Valcea Reservoir were low and constant (0.01–0.08 mg/kg). In Babeni Reservoir sediments, Hg concentrations were very high in the deeper core section (up to 45 mg/kg in the longest core) and decreased to lower concentrations toward the top of the cores (1.3–2.4 mg/kg). This decrease probably reflects technological progress in control of emissions from the Hg-cell-based chlor-alkali industry. Two strong peaks could be distinguished in older sediments. The mean rate of sedimentation (5.9 cm/year) was calculated from the depth of the ¹³⁷Cs Chernobyl peak. This was in good agreement with the sedimentation rate estimated at this site from a bathymetric study. Assuming a constant sedimentation rate, the two Hg peaks would reflect two contamination events in 1987 and 1991, respectively. However, it is also possible that the two peaks belong to the same contamination event in 1987 but were separated by a sediment layer richer in sand and silt. This layer had a low Hg concentration, which can be interpreted as a mass deposition event related to a major flood bringing Hg-free sediments.

Conclusions

Whilst the chlor-alkali plant partly switched to a cleaner technology in 1999, no obvious decrease of Hg concentrations was observed in recent decade. Results from the sediment core reflected the historical trend of Hg release from the chlor-alkali plant, revealed important contamination episodes and confirmed a legacy of contamination of Hg in recent sediments even if the concentrations of Hg decreased toward the surface due to a more efficient emission control.

Recommendations and perspectives

Although the Hg concentrations in Babeni Reservoir sediments were extremely high in the late eighties and they remain one order of magnitude higher in the surface sediments than in sediments from the upstream reservoir, little is known about the transfer of Hg to the biota and human population. Our initial measurements indicate the presence of monomethyl-Hg (MMHg) in pore water, but further studies are necessary to evaluate fluxes of MMHg at the sediment–water interface. Samples of fish and hair from various groups of the local population were recently collected to evaluate the potential hazard of Hg contamination to human health in the Rm Valcea region.

     

Landfill mining from a deposit of the chlorine/organochlorine industry as source of dioxin contamination of animal feed and assessment of the responsible processes

In 1997, the Polychlorinated dibenzo-para-dioxin (PCDD)/Polychlorinated dibenzofuran (PCDF) concentrations in dairy products in Germany and other European countries increased. The PCDD/PCDF source was contaminated lime used in Brazilian citrus pulp pellets. The contaminated lime was mined from an industrial dump site. However, the detailed origin of the PCDD/PCDFs in the lime was not revealed. This paper investigates the contamination origin and describes the link between lime milk from the dumpsite of a chlorine/organochlorine industry and the contaminated lime. The contaminated lime stem from mining at the corporate landfill of Solvay Indupa in Sao Paulo. The landfill was used for 40 years for deposition of production residues and closed in 1996. The factory operated/operates at least two processes with potentially high PCDD/PCDFs releases namely the oxychlorination process for production of ethylene dichloride (EDC) and the chlor-alkali process. The main landfilled waste was lime milk (1.4 million tons) from the vinyl chloride monomer production (via the acetylene process) along with residues from other processes. The PCDD/PCDF fingerprint revealed that most samples from the chemical landfill showed an EDC PCDD/PCDF pattern with a characteristic octachlorodibenzofuran dominance. The PCDD/PCDF pattern of a Rio Grande sediment samples downstream the facility showed a chlor-alkali pattern with a minor impact of the EDC pattern. The case highlights that PCDD/PCDF- and persistent organic pollutants-contaminated sites need to be identified in a comprehensive manner as required by the Stockholm Convention (article 6) and controlled for their impact on the environment and human health. Landfill mining and reuse of materials from contaminated deposits should be prohibited.     

Emergy-based assessment on industrial symbiosis: a case of Shenyang Economic and Technological Development Zone

Industrial symbiosis is the sharing of services, utility, and by-product resources among industries. This is usually made in order to add value, reduce costs, and improve the environment, and therefore has been taken as an effective approach for developing an eco-industrial park, improving resource efficiency, and reducing pollutant emission. Most conventional evaluation approaches ignored the contribution of natural ecosystem to the development of industrial symbiosis and cannot reveal the interrelations between economic development and environmental protection, leading to a need of an innovative evaluation method. Under such a circumstance, we present an emergy analysis-based evaluation method by employing a case study at Shenyang Economic and Technological Development Zone (SETDZ). Specific emergy indicators on industrial symbiosis, including emergy savings and emdollar value of total emergy savings, were developed so that the holistic picture of industrial symbiosis can be presented. Research results show that nonrenewable inputs, imported resource inputs, and associated services could be saved by 89.3, 32.51, and 15.7 %, and the ratio of emergy savings to emergy of the total energy used would be about 25.58 %, and the ratio of the emdollar value of total emergy savings to the total gross regional product (GRP) of SETDZ would be 34.38 % through the implementation of industrial symbiosis. In general, research results indicate that industrial symbiosis could effectively reduce material and energy consumption and improve the overall eco-efficiency. Such a method can provide policy insights to industrial park managers so that they can raise appropriate strategies on developing eco-industrial parks. Useful strategies include identifying more potential industrial symbiosis opportunities, optimizing energy structure, increasing industrial efficiency, recovering local ecosystems, and improving public and industrial awareness of eco-industrial park policies.     

Effects of sodium arsenate exposure on liver fatty acid profiles and oxidative stress in rats

The present study aimed to evaluate the effect of arsenic on liver fatty acids (FA) composition, hepatotoxicity and oxidative status markers in rats. Male rats were randomly devised to six groups (n?=?10 per group) and exposed to sodium arsenate at a dose of 1 and 10 mg/l for 45 and 90 days. Arsenate exposure is associated with significant changes in the FA composition in liver. A significant increase of saturated fatty acids (SFA) in all treated groups (p?<?0.01) and trans unsaturated fatty acids (trans UFA) in rats exposed both for short term for 10 mg/l (p?<?0.05) and long term for 1 and 10 mg/l (p?<?0.001) was observed. However, the cis UFA were significantly decreased in these groups (p?<?0.05). A markedly increase of indicator in cell membrane viscosity expressed as SFA/UFA was reported in the treated groups (p?<?0.001). A significant increase in the level of malondialdehyde by 38.3 % after 90 days of exposure at 10 mg/l was observed. Compared to control rats, significant liver damage was observed at 10 mg/l of arsenate by increasing plasma marker enzymes after 90 days. It is through the histological investigations in hepatic tissues of exposed rats that these damage effects of arsenate were confirmed. The antioxidant perturbations were observed to be more important at groups treated by the high dose (p?<?0.05). An increase in the level of protein carbonyls was observed in all treated groups (p?<?0.05). The present study provides evidence for a direct effect of arsenite on FA composition disturbance causing an increase of SFA and TFAs isomers, liver dysfunction and oxidative stress. Therefore, arsenate can lead to hepatic damage and propensity towards liver cancer.     

Coupling digestion in a pilot-scale UASB reactor and electrochemical oxidation over BDD anode to treat diluted cheese whey

The efficiency of the anaerobic treatment of cheese whey (CW) at mesophilic conditions was investigated. In addition, the applicability of electrochemical oxidation as an advanced post-treatment for the complete removal of chemical oxygen demand (COD) from the anaerobically treated cheese whey was evaluated. The diluted cheese whey, having a pH of 6.5 and a total COD of 6 g/L, was first treated in a 600-L, pilot-scale up-flow anaerobic sludge blanket (UASB) reactor. The UASB process, which was operated for 87 days at mesophilic conditions (32?±?2 °C) at a hydraulic retention time (HRT) of 3 days, led to a COD removal efficiency between 66 and 97 %, while the particulate matter of the wastewater was effectively removed by entrapment in the sludge blanket of the reactor. When the anaerobic reactor effluent was post-treated over a boron-doped diamond (BDD) anode at 9 and 18 A and in the presence of NaCl as the supporting electrolyte, complete removal of COD was attained after 3–4 h of reaction. During electrochemical experiments, three groups of organochlorinated compounds, namely trihalomethanes (THMs), haloacetonitriles (HANs), and haloketons (HKs), as well as 1,2-dichloroethane (DCA) and chloropicrin were identified as by-products of the process; these, alongside free chlorine, are thought to increase the matrix ecotoxicity to Artemia salina.     

Factors influencing silver recovery and power generation in bio-electrochemical reactors

The recovery of silver from Ag⁺ solution coupled with power generation was investigated in bio-electrochemical system (BES). In this system, chemical energy existing in the organic matter in the anode chamber can be converted biologically to electrical energy which can be used for the reduction of Ag⁺ ions in the cathode chamber. Results showed that type of substrate influenced the metabolic pathway and affected the cell voltage progression, and columbic efficiency. Silver recovery was not affected by increasing initial pH (2.0 to 7.0) and Ag⁺ concentration (100 to 1000 mg/L) in the catholyte, whereas power generation was improved. A maximum power density of 8258 mW/m³ and a columbic efficiency of 21.61% could be achieved with 1000 mg/L of Ag⁺. Ag⁺ ions were reduced to form metallic deposits as Ag⁰ crystals on the cathode surface, which were then confirmed by scanning electron microscope (SEM) image and energy dispersive X-ray (EDX) spectrum. The BES reactor had high silver removal (i.e., >96%) after 24 h of operation. When considering the crossover of Ag⁺ ions through the cation exchange membrane, the removal was in the range of 83.73–92.51%. This crossover was not considerable as compared to the Ag⁺ initial concentration. At higher initial Ag⁺ concentration (2000 mg/L), the silver removal decreased to 88.61% and the maximum power density decreased to 5396 mW/m³. This study clearly showed that BES can be employed for silver recovery, wastewater treatment, and also electricity generation.     

Mercury Emissions from a Hazardous Waste Incinerator Equipped with a State-of-the-Art Wet Scrubber

Abstract

Over a six-week period, eleven tests were performed at the U.S. EPA Incineration Research Facility (IRF) in Jefferson, Arkansas to evaluate the fate of trace metals fed to a rotary kiln incinerator equipped with a Calvert Flux-Forcer/Condensation Scrubber pilot plant as the primary air pollution control system (APCS). Test variables were kiln temperature, ranging from 538 °C to 927 °C; waste feed chlorine content, ranging from 0% to 3.4%; and scrubber pressure drop, ranging from 8.2 kPa to 16.9 kPa. Mercury was among the six hazardous constituent trace metals fed to the IRF’s pilotscale rotary kiln incineration system as part of a synthetic waste feed. This paper focuses on the test results solely with respect to mercury.

As expected, mercury behaved as a very volatile metal throughout the tests; it was not detected in any kiln ash samples. Scrubber collection efficiency for mercury ranged from 67% to >99%, averaging 87%; this was somewhat lower than expected and may be attributable to low scrubber loadings.

The ability to collect and analyze representative scrubber water samples appears to have been affected by the waste feed chlorine content; detection of mercury at higher concentrations during high waste-chlorine-content tests is thought to be largely the result of the formation of mercuric chloride, a more water-soluble species, during those tests. As a result, no firm conclusions may be drawn regarding the true impact of waste feed chlorine content on mercury partitioning to the scrubber water. As expected, no significant relationship was observed between kiln exit-gas temperature and mercury partitioning, nor was there a significant relationship with scrubber pressure drop.     

Properties of biochars from conventional and alternative feedstocks and their suitability for metal immobilization in industrial soil

In contaminated soils, excessive concentrations of metals and their high mobility pose a serious environmental risk. A suitable soil amendment can minimize the negative effect of metals in soil. This study investigated the effect of different biochars on metal (Cu, Pb, Zn) immobilization in industrial soil. Biochars produced at 300 and 600 °C from conventional (MS, maize silage; WP, wooden pellets) and alternative (SC, sewage sludge compost; DR, digestate residue) feedstocks were used as soil amendments at a dosage of 10 % (w/w). The type of feedstock and pyrolysis temperature affected the properties of the biochars and their ability to immobilize metal in soil. Compared to production at 300 °C, all biochars produced at 600 °C had higher pH (6.2–10.7), content of ash (7.2–69.0 %) and fixed carbon (21.1–56.7 %), but lower content of volatile matter (9.7–37.2 %). All biochars except DR biochar had lower dissolved organic carbon (DOC) content (1.4–2.3 g C/L) when made at 600 °C. Only MS and SC biochars had higher cation exchange capacity (25.2 and 44.7 cmol/kg, respectively) after charring at 600 °C. All biochars contained low concentrations of Cd, Cu, Ni, Pb and Zn; Cd was volatilized to the greatest extent during pyrolysis. Based on FTIR analysis and molar ratios of H/C and O/C, biochars had a greater degree of carbonization and aromaticity after charring at 600 °C. The efficiency of the biochars in metal immobilization depended mainly on their pH, ash content, and concentration of DOC. SC and DR biochars were more effective for Cu and Zn immobilization than MS and WP biochars, which makes them attractive options for large-scale soil amendment.     

Chemical and microbial characteristics of municipal drinking water supply systems in the Canadian Arctic

Drinking water in the vast Arctic Canadian territory of Nunavut is sourced from surface water lakes or rivers and transferred to man-made or natural reservoirs. The raw water is at a minimum treated by chlorination and distributed to customers either by trucks delivering to a water storage tank inside buildings or through a piped distribution system. The objective of this study was to characterize the chemical and microbial drinking water quality from source to tap in three hamlets (Coral Harbour, Pond Inlet and Pangnirtung—each has a population of <2000) on trucked service, and in Iqaluit (population ~6700), which uses a combination of trucked and piped water conveyance. Generally, the source and drinking water was of satisfactory microbial quality, containing Escherichia coli levels of <1 MPN/100 mL with a few exceptions, and selected pathogenic bacteria and parasites were below detection limits using quantitative polymerase chain reaction (qPCR) methods. Tap water in households receiving trucked water contained less than the recommended 0.2 mg/L of free chlorine, while piped drinking water in Iqaluit complied with Health Canada guidelines for residual chlorine (i.e. >0.2 mg/L free chlorine). Some buildings in the four communities contained manganese (Mn), copper (Cu), iron (Fe) and/or lead (Pb) concentrations above Health Canada guideline values for the aesthetic (Mn, Cu and Fe) and health (Pb) objectives. Corrosion of components of the drinking water distribution system (household storage tanks, premise plumbing) could be contributing to Pb, Cu and Fe levels, as the source water in three of the four communities had low alkalinity. The results point to the need for robust disinfection, which may include secondary disinfection or point-of-use disinfection, to prevent microbial risks in drinking water tanks in buildings and ultimately at the tap.     

Iron-loaded mangosteen as a heterogeneous Fenton catalyst for the treatment of landfill leachate

Iron-loaded mangosteen shell powder (Fe-MSP) was found as an effective heterogeneous Fenton catalyst for the treatment of stabilized landfill leachate. Sonolytically produced catalyst has higher efficiency than other catalysts. At the optimal conditions (pH 3, catalyst concentration of 1,750 mg/L and hydrogen peroxide concentration of 0.26 M), 81 % of the chemical oxygen demand (COD) was removed effectively from the landfill leachate. But, the efficiency of Fe-MSP was reduced in the first recycling due to the poisoning of active sites. A metal leaching study indicated that the degradation of the pollutant is mainly due to solid Fe ions present in Fe-MSP rather than the leached ferrous and ferric ions. Hydroxyl radical production in the system was confirmed by the Fenton oxidation of benzoic acid. Compared to the homogeneous Fenton process, the heterogeneous Fenton process using Fe-MSP had higher COD removal efficiency, indicating the practical applicability of the prepared catalyst.     

Ecological and biological determinants of methylmercury accumulation in tropical coastal fish

This research investigated whether environmental conditions, biological fish characteristics and anthropogenic impacts influenced mercury (Hg) assimilation into the muscle tissue of two fish species from two Brazilian bays, Ilha Grande Bay and Guanabara Bay. Fish and superficial water were collected in different periods. Hg was determined by CV-AAS. Methylmercury (MeHg) was identified and quantified by ECD-GC. Chlorophyll a concentrations in the water column indicated that Ilha Grande Bay and Guanabara Bay were oligotrophic and eutrophic, respectively. Hg in fish ranged from 2.10 to 870.17 μg kg^?1 dry wt. in Ilha Grande Bay and 40.90 to 809.24 μg kg^?1 dry wt. in Guanabara Bay. Slight differences were found between the length-normalized Hg concentrations and its percent of Hg in a voracious predator from the bays. In Guanabara Bay, where the presence of a chlor-alkali plant causes Hg input, the iliophagous fish species showed the highest length-normalized Hg concentrations and the voracious predator the lowest. Iliophagous fish is consumed by voracious predator and, consequently, acts as their MeHg food supply. Iliophagous fish from Ilha Grande Bay presented a higher percent of MeHg (80.0 %) than specimens from Guanabara Bay (54.5 %). This fact suggests that more MeHg was transferred from iliophagous fish to voracious predator in Ilha Grande Bay. At Guanabara Bay, the bioproduction is greater than that at Ilha Grande Bay, presenting the highest biomass in it ecosystem, which may subsequently dilute Hg and reduce its availability to the biota; i.e., influencing in Hg and MeHg availability throughout the food chain. Consequently, more MeHg is available in the aquatic environment of Ilha Grande Bay.     

Enhanced removal of arsenic from a highly laden industrial effluent using a combined coprecipitation/nano-adsorption process

Effective arsenic removal from highly laden industrial wastewater is an important but challenging task. Here, a combined coprecipitation/nano-adsorption process, with ferric chloride and calcium chloride as coprecipitation agents and polymer-based nanocomposite as selective adsorbent, has been validated for arsenic removal from tungsten-smelting wastewater. On the basis of operating optimization, a binary FeCl₃ (520 mg/L)–CaCl₂ (300 mg/L) coprecipitation agent could remove more than 93 % arsenic from the wastewater. The resulting precipitate has proved environmental safety based on leaching toxicity test. Fixed-bed column packed with zirconium or ferric-oxide-loaded nanocomposite was employed for further elimination of arsenic in coprecipitated effluent, resulting in a significant decrease of arsenic (from 0.96 to less than 0.5 mg/L). The working capacity of zirconium-loaded nanocomposite was 220 bed volumes per run, much higher than that of ferric-loaded nanocomposite (40 bed volumes per run). The exhausted zirconium-loaded nanocomposite could be efficiently in situ regenerated with a binary NaOH–NaCl solution for reuse without any significant capacity loss. The results validated the combinational coprecipitation/nano-adsorption process to be a potential alternative for effective arsenic removal from highly laden industrial effluent.     

Comparison of physical technologies for biomass control in biofilters treating gaseous toluene

Excessive accumulation of biomass within gas-phase biofilters often results in the deterioration of removal performance. Compared with chemical and biological technologies, physical technologies are more effective in removing biomass and inducing less inhibition of the biofilter performance. This study applied different physical technologies, namely, air sparging, mechanical mixing, and washing with water at various temperatures, to remove excess biomass in biofilters treating toluene. Filter pressure drop, removed dry biomass, biofilter performance, and microbial metabolic characteristics were analyzed to evaluate the effectiveness of the methods. Results showed that air sparging was inefficient for biomass removal (1 kg dry biomass/m³ filter), whereas mechanical mixing significantly inhibited removal efficiencies (<30%). Washing of the packing with fluids was feasible, and hot fluids can remove a large amount of biomass. However, hot fluids reduce microbial activity and inhibit removal performance. Washing of the packing with either 20°C or 50°C water showed efficiency as >3 kg dry biomass/m³ filter can be removed at both temperatures with removal efficiencies at approximately 40% after treatment. Finally, different technologies were compared and summarized to propose an optimized strategy of biomass control for industrial biofilters.

Implications: This study is to apply different physical technologies, namely, air sparging, mechanical mixing, and washing with water of different temperatures, to remove the excess biomass in biofilters treating toluene. The filter pressure drop, removed dry biomass, biofilter performance, and microbial metabolic characteristics were all analyzed to evaluate the effectiveness of the methods. The results of this study provide useful information regarding biomass control of industrial biofilters.     

Development of a Regenerable System Employing Silica-Titania Composites for the Recovery of Mercury from End-Box Exhaust at a Chlor-Alkali Facility

Abstract

The release of mercury to the environment is of particular concern because of its volatility, persistence, and tendency to bioaccumulate. The recovery of mercury from end-box exhaust at chlor-alkali facilities is important to prevent release into the environment and reduce emissions as required by NESHAP (National Emission Standards for Hazardous Air Pollutants). A pilot-scale photocatalytic reactor packed with silica-titania composite (STC) pellets was tested at a chlor-alkali facility over a 3-month period. This pilot reactor treated up to 10 ft³/min (ACFM) of end-box exhaust and achieved 95% removal. The pilot reactor was able to maintain excellent removal efficiency even with large fluctuations in influent mercury concentration (400–1600 μg/ft³).The STC pellets were regenerated ex situ by regeneration with hydrochloric acid and performed similarly to virgin STC pellets when returned to service. On the basis of these promising results, two full-scale reactors with in situ regeneration capabilities were installed and operated. After optimization, these reactors performed similarly to the pilot reactor. A cost analysis was performed comparing the treatment costs (i.e., cost per pound of mercury removed) for sulfur-impregnated activated carbon and the STC system. The STC proved to be both technologically and economically feasible for this installation.     

Disinfection performance of chlorine dioxide gas at ultra-low concentrations and the decay rules under different environmental factors

ABSTRACT

Gaseous chlorine dioxide (ClO₂) is one of the most promising air disinfectants. In this study, an ultra-low concentration of ClO₂ gas (< 1.2 mg/m³) was generated in an office at various levels of humidity and illuminance to investigate the decay law. The disinfection efficiency and metal corrosiveness of ultra-low concentrations of ClO₂ gas were also studied using an experimental chamber. At 48% and 75% humidity, the decay rate constants of ClO₂ gas were 0.0034 min^?1 and 0.0036 min^?1, respectively. The rate of decline of the ClO₂ concentration increased as the humidity of the environment increased. The decay rate constant of ClO₂ gas at an illuminance of 76 lux and 3429 lux was 0.0034 min^?1 and 0.00427 min^?1, respectively; hence, the decay rate increased with increased illumination. At a humidity of 72% and illuminance of 2112 lux, the decay rate constant reached 0.00880 min^?1. The effects of humidity and illuminance on the attenuation of the ClO₂ concentration were strongly synergistic. When the gas concentration was maintained below 0.9 mg/m³, the disinfection rate of ClO₂ on bacteria (P. aeruginosa, V. mimicus and S. aureus) exceeded 99.9%; thus, ClO₂ gas exhibited a high disinfection efficiency. In addition, there was no corrosion to various metals by ClO₂ under the same conditions. Consequently, gaseous ClO₂ at ultra-low concentrations has a high sterilization efficiency and is non-corrosive to metals.     

Enhanced degradation of ortho-nitrochlorobenzene by the combined system of zero-valent iron reduction and persulfate oxidation in soils

ortho-Nitrochlorobenzene (o-NCB) in soil poses significant health risks to human because of its persistence and high toxicity. The removal of o-NCB by both zero-valent iron (ZVI) and chemical oxidation (persulfate) was investigated by batch experiments. The o-NCB removal rate increases significantly from 15.1 to 97.3 % with an increase of iron dosage from 0.1 to 1.0 mmol g^?1. The o-NCB removal rate increases with the decrease of the initial solution pH, and a removal efficiency of 90.3 % is obtained at an initial pH value of 6.8 in this combined system. It is found that temperature and soil moisture could also increase the o-NCB removal rate. The o-NCB degradation rate increases from 83.9 to 96.2 % and from 41.5 to 82.4 % with an increase of temperature (15 to 35 °C) and soil moisture (0.25 to 1.50 mL g^?1), respectively. Compared to the persulfate oxidation system and ZVI system, the persulfate–iron system shows high o-NCB removal capacity. o-NCB removal rates of 41.5 and 62.4 % are obtained in both the persulfate oxidation system and the ZVI system, while the removal rate of o-NCB is 90.3 % in the persulfate–iron system.