Solvent extraction for heavy crude oil removal from contaminated soils

A new strategy of heavy crude oil removal from contaminated soils was studied. The hexane-acetone solvent mixture was used to investigate the ability of solvent extraction technique for cleaning up soils under various extraction conditions. The mixtures of hexane and acetone (25 vol%) were demonstrated to be the most effective in removing petroleum hydrocarbons from contaminated soils and approx 90% of saturates, naphthene aromatics, polar aromatics, and 60% of nC₇-asphaltenes were removed. Kinetic experiments demonstrated that the equilibrium was reached in 5 min and the majority of the oil pollutants were removed within 0.5 min. The effect of the ratio between solvent and soil on the extraction efficiency was also studied and results showed that the efficiency would increase following the higher solvent soil ratio. Then the multistage continuous extraction was considered to enhance the removal efficiency of oil pollutants. Three stages crosscurrent and countercurrent solvent extraction with the solvent soil ratio 6:1 removed 97% oil contaminants from soil. Clearly the results showed that the mixed-solvent of hexane and acetone (25 vol%) with character of low-toxic, acceptable cost and high efficiency was promising in solvent extraction to remove heavy oil fractions as well as petroleum hydrocarbons from contaminated soils.     

Surfactant solubilization of hydrophobic compounds in soil and water

The soil/water partition coefficient (K_d) of hexachlorobenzene (HCB) ranged from 220 1/kg to 1800 1/kg for eight soils having a wide range of physico-chemical properties. K_d normalised to soil organic carbon (K_oc) was found to be 28000 ± 4800 1/kg. Anionic surfactant dodecylsulphate (DS) present at concentrations above the critical micellar concentration (CMC) caused reductions in the apparent soil/water partition coefficient (K_d ^*) in the range of 3–26 times for most soils and up to 36–91 times for sandy soils. Below CMC, at environmentally relevant surfactant concentrations, K_d ^* was reduced by a factor of 1–13. For clay and calcareous soils significant adsorption/complexation/precipitation of DS occurred. At the lowest DS concentration this produced a two-fold increase in K_d ^*. At increasing DS concentrations this effect was shielded by the solubihzing effect from DS. Monomer (K_mn) and micellar (K_mc) surfactant/water partition coefficients for HCB were determined to be, 980 ± 190 1/kg and 21000 ± 1600 1/kg, respectively.     

Short-chain chlorinated paraffins (SCCPs) in surface soil from a background area in China: occurrence, distribution, and congener profiles

Short-chain chlorinated paraffins (SCCPs) are extremely complex technical mixtures of polychlorinated n-alkanes with carbon chain lengths from C₁₀ to C₁₃ and chlorine content between 49 and 70 %. SCCPs are under consideration for inclusion in the Stockholm Convention on persistent organic pollutants. SCCPs have been used extensively in industrial production, but little is known about the pollution level in soil environment in China. In this study, levels and distribution of SCCPs in soil samples from Chongming Island were analyzed. Concentrations of total SCCPs in soil samples ranged from 0.42 to 420 ng?g^?1, with a median of 9.6 ng?g^?1. The ubiquitous occurrence of SCCPs in Chongming Island implied that long-range atmospheric transport and soil–air exchange may be the most important pathways for SCCP contamination in the background area. The localized SCCP contamination could be derived from an unidentified source. Hierarchical cluster analysis indicated that C₁₃- and C₁₁-congeners were predominant in most soils and C₁₀- and C₁₂-congeners dominated in the remaining soils. Cl₇- and Cl₈-congeners were on the average the most dominant chlorine congeners in nearly all soils. Principal component analysis suggested that the separation of even and odd carbon chain congeners occurred during long-range atmospheric transport and aging in soil in the study area.     

Organochlorine pesticides and polychlorinated biphenyls in soils surrounding the Tanggu Chemical Industrial District of Tianjin, China

The spatial distribution of persistent organic pollutants (POPs) was examined in soils surrounding the Tanggu Chemical Industrial District in Tianjin, China. The concentrations of hexachlorocyclohexanes (HCHs), dichlorodiphenyltrichloroethanes (DDTs), hexachlorobenzenes (HCBs), and polychlorinated biphenyls (PCBs) were determined in 70 surface soils using accelerated solvent extraction and gas chromatography with electron capture detection. The results showed that the ranges of ∑HCH, ∑DDT, ΣHCB, and ∑PCB concentrations in soils were 2.1–12,549 μg?kg^?1 (average, 965 μg?kg^?1), n.d.–2,033 μg?kg^?1 (average, 88.4 μg?kg^?1), n.d.–1,924 μg?kg^?1 (average, 349 μg?kg^?1), and n.d.–373 μg?kg^?1 (average, 46.2 μg?kg^?1), respectively. Of these, HCHs were the dominant POPs, accounting for 75 % of the total organochlorine pesticide (OCP) residues. Overall, the spatial distribution of OCP concentrations showed a decreasing trend from the center of the Tanggu District to the surrounding areas. Two major pollution sources were Tianjin Dagu Chemical Co., Ltd. in the district center and the Tianjin Chemical Plant in Hangu District. In contrast, PCB concentrations were relatively high in the Haihe estuary to the east and low to the west of the study area. Component analysis of OCPs in these soils showed that they mainly came from industrial point sources. Compared with soils in other regions, soil DDT pollution was at a medium level in the Tanggu Chemical Industrial District, but associated HCH, HCB, and PCB pollution was relatively heavy. By multivariate statistical analyses, Tianjin Dagu Chemical Co., Ltd. was recognized as the main source of POPs, and soil properties were clarified to play an important role on the distribution and composition of POPs, especially the organic carbon content.     

Adsorption-desorption and leaching of pyraclostrobin in Indian soils

Pyraclostrobin is a new broad-spectrum foliar applied and seed protectant fungicide of the strobilurin group. In this paper, adsorption-desorption of pyraclostrobin has been investigated in three different soils viz. Inceptisol (sandy loam, Delhi), Vertisol (sandy clay, Hyderabad) and Ultisol (sandy clay loam, Thrissur). Effect of organic matter and clay content on sorption was also studied in Inceptisol of Delhi. Leaching potential of pyraclostrobin as influenced by rainfall was studied in intact soil columns to confirm the results of adsorption-desorption studies. The adsorption studies were carried out at initial concentrations of 0.05, 0.1, 0.5, 1 and 1.5 μg mL^?1. The distribution coefficient (K_d) values in three test soils ranged from 4.91 to 18.26 indicating moderate to high adsorption. Among the three test soils, adsorption was the highest in Ultisol (K_d 18.26), followed by Vertisol (K_d 9.87) and Inceptisol (K_d 4.91). K_F value was also highest for Ultisol soil (66.21), followed by Vertisol (40.88) and Inceptisol (8.59). S-type adsorption isotherms were observed in all the three test soils. K_d values in organic carbon-removed soil and clay-removed soil were 3.57 and 2.83 respectively, indicating lower adsorption than normal Inceptisol. Desorption studies were carried out at initial concentrations of 0.5, 1 and 1.5 μg mL^?1. Desorption was the greatest in Inceptisol, followed by Vertisol and Ultisol. Amounts of pyraclostrobin desorbed in three desorption cycles for different concentrations were 23.1–25.3%, 9.4–20.7% and 8.1–13.6% in Inceptisol, Vertisol and Ultisol respectively. Desorption was higher in clay fraction-removed and organic carbonremoved soils than normal Inceptisol. Desorption was slower than adsorption in all the test soils, indicating hysteresis effect (with hysteresis coefficient values varying from 0.05 to 0.20). Low values of hysteresis coefficient suggest high hysteresis effect indicating easy and strong adsorption, and slow desorption, of pyraclostrobin in soils. Higher hysteresis coefficient values in organic carbon removed soil (0.25–0.30) and clay fraction removed soil (0.28–0.36) as compared to normal Inceptisol soil suggest relatively weak adsorption and easy desorption of pyraclostrobin. Results of regression analysis suggest that the organic matter and pH of the soil play a major role in adsorption of pyraclostrobin. Leaching studies were carried out in intact soil columns in Inceptisol. The columns were leached with different amounts of water simulating different amounts of rainfall. The results suggest that most of the pyraclostrobin residues will remain present in the top soil layers even under high rainfall conditions and chances of pyraclostrobin moving to lower soil depth are almost negligible.     

Identification,abundance and origin of atmospheric organic particulate matter in a Portuguese rural area

Respirable suspended particles high-volume samples were collected from a coastal-rural site in the centre of Portugal in August 1997 and their solvent-extractable organic compounds were subjected to characterisation by gas chromatography-mass spectrometry. Particles were also analysed by a thermal/optical technique in order to determine their black and organic carbon content. The total lipid extract yields ranged from 20 to 63 μg m⁻³, containing mainly aliphatic hydrocarbons such as n-alkanes, acids, alcohols, aldehydes, ketones and polycyclic aromatic hydrocarbons. The higher input of vascular plant wax components was demonstrated by the distribution patterns of the n-alkanes, n-alkanoic acids and n-alkanols homologous series, with C_max at C₂₉, C₂₂/C₂₄ and C₃₀, respectively. The CPI values for these series were in the range 1.8–9.7, being indicative of recent biogenic input from microbial lipid residues and flora epicuticular components. Specific natural constituents (e.g. phytosterols, terpenes, etc.) were identified as molecular markers. Some oxidation products from volatile organic precursors were also present in the aerosols. In addition, all samples had a component of petroleum hydrocarbons representing urban and vehicular emissions probably transported from the nearest cities and from the motorway in the vicinity. This data set could be used to make a mass balance with organic carbon, organic extracts and elutable matter, permitting also the comparison with lipid signatures observed for other regions.     

Concentrations,atmospheric partitioning,and air–water/soil surface exchange of polychlorinated dibenzo-p-dioxin and dibenzofuran along the upper reaches of the Haihe River basin,North China

Polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/PCDF) were overall measured and compared in ambient air, water, soils, and sediments along the upper reaches of the Haihe River of North China, so as to evaluate their concentrations, profiles, and to understand the processes of gas–particle partitioning and air–water/soil exchange. The following results were obtained: (1) The average concentrations (toxic equivalents, TEQs) of 2,3,7,8-PCDD/PCDF in air, water, sediment, and soil samples were 4,855 fg/m³, 9.5 pg/L, 99.2 pg/g dry weight (dw), and 56.4 pg/g (203 fg TEQ/m³, 0.46 pg TEQ/L, 2.2 pg TEQ/g dw, and 1.3 pg TEQ/g, respectively), respectively. (2) Although OCDF, 1,2,3,4,6,7,8-HpCDF, OCDD, and 1,2,3,4,6,7,8-HpCDD were the dominant congeners among four environmental sinks, obvious discrepancies of these congener and homologue patterns of PCDD/PCDF were observed still. (3) Significant linear correlations for PCDD/PCDF were observed between the gas–particle partition coefficient (K _p) and the subcooled liquid vapor pressure (P _L ⁰) and octanol–air partition coefficient (K _oa). (4) Fugacity fraction values of air–water exchange indicated that most of PCDD/PCDF homologues were dominated by net volatilization from water into air. The low-chlorinated PCDD/PCDF (tetra- to hexa-) presented a strong net volatilization from the soil into air, while high-chlorinated PCDD/PCDF (hepta- to octa-) were mainly close to equilibrium for air–soil exchange.     

Sorption of chlorpyrifos and fonofos on four soils and turfgrass thatch using membrane filters

Abstract

Chemical transport in soil is a major factor influencing soil and water contamination. Four soils and turfgrass thatch, representing a wide range of organic carbon OC content were studied to determine sorption K_d and K_f parameters for the insecticides chlorpyrifos and fonofos. The batch equilibrium method was used. The concentration of insecticide was measured in the solution as well as in the solid phase to determine the most accurate sorption data. Four soils and thatch were equilibrated for 24 h at 22 ± 1^OC with aqueous insecticide solutions. Four concentrations of the insecticides, each <50% of their respective water solubilities, were selected for the experiments. After extraction with an organic solvent, the concentration of insecticides in the aqueous solution was determined by gas liquid chromatography using electron capture detection for chlorpyrifos, and nitrogen/phosphorus detection for fonofos. Data obtained were fitted to the log and simple linear form of the Freundlich equation. Mass balance Freundlich isotherm exponents n ranged between 0.82 and 0.93 for chlorpyrifos. 0.82 and 1.21 for fonofos, with r² ≥ 0.97. K_oc (percent of organic carbon %OC normalized Sorption coefficient) values were calculated by using experimentally developed K_d and K_f coefficients in relation to OC levels from 0.29 to 34.85%. K_d and K_f coefficients of both insecticides were positively correlated with OC (r² ≥ 0.96). organic matter OM (r² ≥ 0.96), and cation exchange capacity CEC (r² ≥ 0.90).     

The organic contamination level based on the total soil mass is not a proper index of the soil contamination intensity

Concentrations of organic contaminants in common productive soils based on the total soil mass give a misleading account of actual contamination effects. This is attributed to the fact that productive soils are essentially water-saturated, with the result that the soil uptake of organic compounds occurs principally by partition into the soil organic matter (SOM). This report illustrates that the soil contamination intensity of a compound is governed by the concentration in the SOM (C_om) rather than by the concentration in whole soil (C_s). Supporting data consist of the measured levels and toxicities of many pesticides in soils of widely differing SOM contents and the related levels in in-situ crops that defy explanation by the C_s values. This SOM-based index is timely needed for evaluating the contamination effects of food crops grown in different soils and for establishing a dependable priority ranking for intended remediation of numerous contamination sites.     

Detection and quantification of chlordecone in contaminated soils from the French West Indies by GC-MS using the 13C10-chlordecone stable isotope as a tracer

Chlordecone is an organochlorine insecticide that has been widely used to control banana weevil in the French West Indies. As a result of this intense use, up to 20,000 ha are contaminated by this insecticide in the French West Indies, and this causes environmental damage and health problems. A scenario of exposure was drawn by French authorities, based on land usage records. Many efforts have been made to monitor the occurrence of chlordecone and its main metabolites using different analytical methods, including GC, GC/MS, LC/MS, and NIRS. Although these different methods allow for the detection and quantification of chlordecone from soils, none of them estimate the bottleneck caused by extraction of this organochlorine from soils with high adsorption ability. In this study, we used ¹³C₁₀-chlordecone as a tracer to estimate chlordecone extraction yield and to quantify chlordecone in soil extracts based on the ¹³C/¹²C isotope dilution. We report the optimization of ¹³C₁₀-chlordecone extraction from an Andosol. The method was found to be linear from 0.118 to 43 mg kg^?1 in the Andosol, with an instrumental detection limit estimated at 8.84 μg kg^?1. This method showed that chlordecone ranged from 35.4 down to 0.18 mg kg^?1 in Andosol, Nitisol, Ferralsol, and Fluvisol soil types. Traces of the metabolite β-monohydrochlordecone were detected in the Andosol, Nitisol, and Ferralsol soil samples. This last result indicates that this method could be useful to monitor the fate of chlordecone in soils of the French West Indies.     

Sorption of polar and nonpolar organic contaminants by oil-contaminated soil

Sorption of nonpolar (phenanthrene and butylate) and polar (atrazine and diuron) organic chemicals to oil-contaminated soil was examined to investigate oil effects on sorption of organic chemicals and to derive oil–water distribution coefficients (K_oil). The resulting oil-contaminated soil–water distribution coefficients (K_d) for phenanthrene demonstrated sorption-enhancing effects at both lower and higher oil concentrations (C_oil) but sorption-reducing (competitive) effects at intermediate C_oil (approximately 1 g kg⁻¹). Rationalization of the different dominant effects was attempted in terms of the relative aliphatic carbon content which determines the accessibility of the aromatic cores to phenanthrene. Little or no competitive effect occurred for butylate because its sorption was dominated by partitioning. For atrazine and diuron, the changes in K_d at C_oil above approximately 1 g kg⁻¹ were negligible, indicating that the presently investigated oil has little or no effect on the two tested compounds even though the polarity of the oil is much less than soil organic matter (SOM). Therefore, specific interactions with the active groups (aromatic and polar domains) are dominantly responsible for the sorption of polar sorbates, and thus their sorption is controlled by available sorption sites. This study showed that the oil has the potential to be a dominant sorptive phase for nonpolar pollutants when compared to SOM, but hardly so for polar compounds. The results may aid in a better understanding of the role of the aliphatic and aromatic domains in sorption of nonpolar and polar organic pollutants.     

Petroleum mass removal from low permeability sediment using air sparging/soil vapor extraction: impact of continuous or pulsed operation

Air sparging and soil vapor extraction (AS/SVE) are innovative remediation techniques that utilize volatilization and microbial degradation to remediate petroleum spills from soils and groundwater. This in situ study investigated the use of AS/SVE to remediate a gasoline spill from a leaking underground storage tank (UST) in the low permeability, clayey soil of the Appalachian Piedmont. The objectives of this study were to evaluate AS/SVE in low permeability soils by quantifying petroleum mass removal rates, monitoring vadose zone contaminant levels, and comparing the mass extraction rates of continuous AS/SVE to 8 and 24 h pulsed operation. The objectives were met by collecting AS/SVE exhaust gas samples and vadose zone air from multi-depth soil vapor probes. Samples were analyzed for O₂, CO₂, BTEX (benzene, toluene, ethylbenzene, xylene), and total combustible hydrocarbon (TCH) concentrations using portable hand meters and gas chromatography. Continuous AS/SVE was effective in removing 608 kg of petroleum hydrocarbons from low permeability soil in 44 days (14.3 kg day⁻¹). Mass removal rates ranged from 2.6 times higher to 5.1 times lower than other AS/SVE studies performed in sandy sediments. BTEX levels in the vadose zone were reduced from about 5 ppm to 1 ppm. Ten pulsed AS/SVE tests removed 78 kg in 23 days and the mean mass removal rate (17.6 kg day⁻¹) was significantly higher than the last 15 days of continuous extraction. Pulsed operation may be preferable to continuous operation because of increased mass removal and decreased energy consumption.     

Using variances in hydrocarbon concentration and carbon stable isotope to determine the important influence of irrigated water on petroleum accumulation in surface soil

Hunpu is a wastewater-irrigated area southwest of Shenyang. To evaluate petroleum contamination and identify its sources at the area, the aliphatic hydrocarbons and compound-specific carbon stable isotopes of n-alkanes in the soil, irrigation water, and atmospheric deposition were analyzed. The analyses of hydrocarbon concentrations and geochemical characteristics reveal that the water is moderately contaminated by degraded heavy oil. According to the isotope analysis, inputs of modern C3 plants and degraded petroleum are present in the water, air, and soil. The similarities and dissimilarities among the water, air, and soil samples were determined by concentration, isotope, and multivariate statistical analyses. Hydrocarbons from various sources, as well as the water/atmospheric deposition samples, are more effectively differentiated through principal component analysis of carbon stable isotope ratios (δ¹³C) relative to hydrocarbon concentrations. Redundancy analysis indicates that 57.1 % of the variance in the δ¹³C of the soil can be explained by the δ¹³C of both the water and air, and 35.5 % of the variance in the hydrocarbon concentrations of the soil can be explained by hydrocarbon concentrations of both the water and the air. The δ¹³C in the atmospheric deposition accounts for 28.2 % of the δ¹³C variance in the soil, which is considerably higher than the variance in hydrocarbon concentrations of the soil explained by hydrocarbon concentrations of the atmospheric deposition (7.7 %). In contrast to δ¹³C analysis, the analysis of hydrocarbon concentrations underestimates the effect of petroleum contamination in the irrigated water and air on the surface soil. Overall, the irrigated water exerts a larger effect on the surface soil than does the atmospheric deposition.     

Effect of soil and sediment composition on acetochlor sorption and desorption

Background, aim, and scope  Herbicide fate and its transport in soils and sediments greatly depend upon sorption–desorption processes. Quantitative determination of herbicide sorption–desorption is therefore essential for both the understanding of transport and the sorption equilibrium in the soil/sediment–water system; and it is also an important parameter for predicting herbicide fate using mathematical simulation models. The total soil/sediment organic carbon content and its qualitative characteristics are the most important factors affecting sorption–desorption of herbicides in soil or sediment. Since the acetochlor is one of the most frequently used herbicides in Slovakia to control annual grasses and certain annual broad-leaved weeds in maize and potatoes, and posses various negative health effects on human beings, our aim in this study was to investigate acetochlor sorption and desorption in various soil/sediment samples from Slovakia. The main soil/sediment characteristics governing acetochlor sorption–desorption were also identified. Materials and methods  The sorption–desorption of acetochlor, using the batch equilibration method, was studied on eight surface soils, one subsurface soil and five sediments collected from the Laborec River and three water reservoirs. Soils and sediments were characterized by commonly used methods for their total organic carbon content, distribution of humus components, pH, grain-size distribution, and smectite content, and for calcium carbonate content. The effect of soil/sediment characteristics on acetochlor sorption–desorption was examined by simple correlation analysis. Results  Sorption of acetochlor was expressed as the distribution coefficient (K _d). K _d values slightly decreased as the initial acetochlor concentration increased. These values indicated that acetochlor was moderately sorbed by soils and sediments. Highly significant correlations between the K _d values and the organic carbon content were observed at both initial concentrations. However, sorption of acetochlor was most closely correlated to the humic acid carbon, and less to the fulvic acid carbon. The total organic carbon content was found to also significantly influence acetochlor desorption. Discussion  Since the strong linear relationship between the K _d values of acetochlor and the organic carbon content was already released, the corresponding K _oc values were calculated. Considerable variation in the K _oc values suggested that other soil/sediment parameters besides the total soil organic carbon content could be involved in acetochlor sorption. This was revealed by a significant correlation between the K _oc values and the ratio of humic acid carbon to fulvic acid carbon (C_HA/C_FA). Conclusions  When comparing acetochlor sorption in a range of soils and sediments, different K _d values which are strongly correlated to the total organic carbon content were found. Concerning the humus fractions, the humic acid carbon content was strongly correlated to the K _d values, and it is therefore a better predictor of the acetochlor sorption than the total organic carbon content. Variation in the K _oc values was attributed to the differences in distribution of humus components between soils and sediments. Desorption of acetochlor was significantly influenced by total organic carbon content, with a greater organic carbon content reducing desorption. Recommendations and perspectives  This study examined the sorption–desorption processes of acetochlor in soils and sediments. The obtained sorption data are important for qualitative assessment of acetochlor mobility in natural solids, but further studies must be carried out to understand its environmental fate and transport more thoroughly. Although, the total organic carbon content, the humus fractions of the organic matter and the C_HA/C_FA ratio were sufficient predictors of the acetochlor sorption–desorption. Further investigations of the structural and chemical characteristics of humic substances derived from different origins are necessary to more preciously explain differences in acetochlor sorption in the soils and sediments observed in this study.     

Bioremediation of acidic oily sludge-contaminated soil by the novel yeast strain Candida digboiensis TERI ASN6

Background, aim, and scope

Primitive wax refining techniques had resulted in almost 50,000 tonnes of acidic oily sludge (pH 1–3) being accumulated inside the Digboi refinery premises in Assam state, northeast India. A novel yeast species Candida digboiensis TERI ASN6 was obtained that could degrade the acidic petroleum hydrocarbons at pH 3 under laboratory conditions. The aim of this study was to evaluate the degradation potential of this strain under laboratory and field conditions.

Materials and methods

The ability of TERI ASN6 to degrade the hydrocarbons found in the acidic oily sludge was established by gravimetry and gas chromatography–mass spectroscopy. Following this, a feasibility study was done, on site, to study various treatments for the remediation of the acidic sludge. Among the treatments, the application of C. digboiensis TERI ASN6 with nutrients showed the highest degradation of the acidic oily sludge. This treatment was then selected for the full-scale bioremediation study conducted on site, inside the refinery premises.

Results

The novel yeast strain TERI ASN6 could degrade 40 mg of eicosane in 50 ml of minimal salts medium in 10 days and 72% of heneicosane in 192 h at pH 3. The degradation of alkanes yielded monocarboxylic acid intermediates while the polycyclic aromatic hydrocarbon pyrene found in the acidic oily sludge yielded the oxygenated intermediate pyrenol. In the feasibility study, the application of TERI ASN6 with nutrients showed a reduction of solvent extractable total petroleum hydrocarbon (TPH) from 160 to 28.81 g kg^?1 soil as compared to a TPH reduction from 183.85 to 151.10 g kg^?1 soil in the untreated control in 135 days. The full-scale bioremediation study in a 3,280-m² area in the refinery showed a reduction of TPH from 184.06 to 7.96 g kg^?1 soil in 175 days.

Discussion

Degradation of petroleum hydrocarbons by microbes is a well-known phenomenon, but most microbes are unable to withstand the low pH conditions found in Digboi refinery. The strain C. digboiensis could efficiently degrade the acidic oily sludge on site because of its robust nature, probably acquired by prolonged exposure to the contaminants.

Conclusions

This study establishes the potential of novel yeast strain to bioremediate hydrocarbons at low pH under field conditions.

Recommendations and perspectives

Acidic oily sludge is a potential environmental hazard. The components of the oily sludge are toxic and carcinogenic, and the acidity of the sludge further increases this problem. These results establish that the novel yeast strain C. digboiensis was able to degrade hydrocarbons at low pH and can therefore be used for bioremediating soils that have been contaminated by acidic hydrocarbon wastes generated by other methods as well.     

Modelling the extraction of soil contaminants with supercritical carbon dioxide

Extractions of volatile organic compounds (VOC’s) in contaminated soil from petroleum site were performed with supercritical carbon dioxide at different temperatures, pressures, extraction times, solvent flow rates, soil moisture contents and soil acidity. Three soil systems were investigated in order to compare the best parameters for extraction. A central composite rotatable design has been used to evaluate the influence of operation conditions on the extraction efficiency to generate model equations representing the types of soil. The results indicate that at least 70-80% of the initial amount of VOC’s can be removed at moderate temperatures even at very high moisture content. Supercritical extraction is best suited to silt type soils which have a low adsorption capacity. VOC’s recoveries from the artificial contaminated soil samples were higher in comparison with real contaminated soils. At moderate temperatures, the extraction efficiency for real soils is low because pollutants bind strongly to the soil.     

Organic Matter of the Troposphere—II.: Natural Background of biogenic lipid matter in aerosols over the rural western United States

Higher plant waxes are the predominant natural components in the lipid fractions (> C₁₅) of aerosols sampled over rural and oceanic regions. Hydrocarbon, fatty acid, ketone and fatty alcohol fractions of the lipids were characterized in terms of their contents of homologous compound series and specific biogenic molecular markers. Particulate samples from the rural western United States have been analyzed and compared with samples from urban Los Angeles and remote areas over the Atlantic Ocean. The samples from rural sites contained predominantly vascular plant wax and lesser amounts of higher plant sterols and resin residues. Urban samples and, to varying degrees, some rural samples contained primarily higher weight residues of petroleum products. The loadings of hydrocarbons derived from higher plant waxes ranged approximately from 10 to 160 ng m⁻³ of air (for fatty acids, 10–100 ng m⁻³ and for fatty alcohols, 10–200 ng m⁻³). Higher molecular weight lipids (i.e. plant epicuticular wax, terpenes, etc.) from flora comprise a significant component of the organic carbon in rural aerosols. Primary biogenic residues are major components of aerosols in all areas and they are important components in the global cycling of organic carbon.     

Acetamiprid,carbendazim, diuron and thiamethoxam sorption in two Brazilian tropical soils

Sorption of acetamiprid ((E)-N1-[(6-chloro-3-pyridyl)methyl]-N2-cyano-N1-methylacetamidine), carbendazim (methyl benzimidazol-2-ylcarbamate), diuron (N-(3,4-dichlorophenyl)-N, N-dimethyl urea) and thiamethoxam (3-(2-chloro-thiazol-5-ylmethyl)-5-methyl-[1,3,5]oxadiazinan-4-ylidene-N-nitroamine) was evaluated in two Brazilian tropical soils, Oxisol and Entisol, from Primavera do Leste region, Mato Grosso State, Brazil. To describe the sorption process, batch experiments were carried out. Linear and Freundlich isotherm models were used to calculate the K _d and K _f coefficients from experimental data. The K _d values were utilized to calculate the partition coefficient normalized to soil organic carbon (K _oc ). For the pesticides acetamiprid, carbendazim, diuron and thiamenthoxan the K _oc (mL g^{? 1}) values ranged in both soils from 98 – 3235, 1024 – 2644, 145 – 2631 and 104 – 2877, respectively. From the studied pesticides, only carbendazim presented correlation (r² = 0.82 and p < 0.01) with soil organic carbon (OC) content. Acetamiprid and thiamethoxam showed low sorption coefficients, representing a high risk of surface and ground water contamination.     

Effects of petroleum contamination on soil microbial numbers, metabolic activity and urease activity

The influence of petroleum contamination on soil microbial activities was investigated in 13 soil samples from sites around an injection water well (Iw-1, 2, 3, 4) (total petroleum hydrocarbons (TPH): 7.5-78 mg kg⁻¹), an oil production well (Op-1, 2, 3, 4, 5) (TPH: 149-1110 mg kg⁻¹), and an oil spill accident well (Os-1, 2, 3, 4) (TPH: 4500-34 600 mg kg⁻¹). The growth rate constant (μ) of glucose stimulated organisms, determined by microcalorimetry, was higher in Iw soil samples than in Op and Os samples. Total cultivable bacteria and fungi and urease activity also decreased with increasing concentration of TPH. Total heat produced demonstrated that TPH at concentrations less than about 1 g kg⁻¹ soil stimulated anaerobic respiration. A positive correlation between TPH and soil organic matter (OM) and stimulation of fungi-bacteria-urease at low TPH doses suggested that TPH is bound to soil OM and slowly metabolized in Iw soils during OM consumption. These methods can be used to evaluate the potential of polluted soils to carry out self-bioremediation by metabolizing TPH.     

Estimation of ecotoxicity of petroleum hydrocarbon mixtures in soil based on HPLC–GCXGC analysis

Detailed HPLC–GCXGC/FID (high performance liquid chromatography followed by comprehensive two-dimensional gas chromatography with flame-ionization detection) analysis of oil-contaminated soils was performed to interpret results of selected acute ecotoxicity assays. For the five ecotoxicity assays tested, plant seed germination and Microtox^® were selected as most sensitive for evaluating ecotoxicity of the oil in the soil phase and in the leaching water, respectively. The measured toxicity for cress when testing the soil samples did not correspond to TPH concentration in the soil. A detailed chemical composition analysis of the oil contamination using HPLC–GCXGC/FID allows to better predict the ecotoxicological risk and leaching potential of petroleum hydrocarbons in soil. Cress biomass production per plant was well correlated to the total aromatic hydrocarbon concentration (R² = 0.79, n = 6), while cress seed germination was correlated (R² = 0.82, n = 6) with total concentration of “highly water-soluble aromatic hydrocarbons” (HSaromatics). The observed ecotoxicity of the leaching water for Microtox-bacteria related well to calculated (based on the HPLC–GCXGC/FID results) petroleum hydrocarbon equilibrium concentrations in water.