Fate of nickel in a lime-stabilized biosolid,a calcareous soil and soil–biosolid mixtures

Soil contamination with anthropogenic metals resulting from biosolid application is widespread around the world. To better predict the environmental fate and mobility of contaminants, it is critical to study the capacity of biosolid-amended soils to retain and release metals. In this paper, nickel adsorption onto a calcareous soil, a lime-stabilized biosolid, and soil–biosolid mixtures (30, 75, and 150 t biosolid/ha) was studied in batch experiments. Sorption experiments showed that (1) Ni adsorption was higher onto the biosolid than the calcareous soil, and (2) biosolid acted as an adsorbent in the biosolid–soil mixtures by increasing Ni retention capacity. The sorption tests were complemented with the estimation of Ni adsorption reversibility by successive applications of extraction solutions with water, calcium (100 mg/L), and oxalic acid (equivalent to 100 mg carbon/L). It has been shown that Ni desorption rates in soil and biosolid-amended soils were lower than 30 % whatever the chemical reagent, indicating that Ni was strongly adsorbed on the different systems. This adsorption/desorption hysteresis effect was particularly significant at the highest biosolid concentration (150 t/ha). Finally, an adsorption empirical model was used to estimate the maximum permissible biosolid application rate using French national guideline. It has been shown that desorption effects should be quantitatively considered to estimate relevant biosolid loadings.     

Chloroform – concentration gradients in soil air and atmospheric air,and emission fluxes from soil

Since we demonstrated the natural formation of chloroform in soil, the question arose to which extent this contributes to the chloroform present in the atmosphere. Concentration gradients in soil air and atmospheric air of different forests were measured. Chloroform concentration gradients indicating emission occur in forest soils and the atmosphere under the canopy, whereas this was not observed for other chlorinated solvents. Above the canopy all concentration gradients observed for chloroform and 1,1,1-trichloroethane indicate deposition. The emission flux was measured using enclosures and calculated from the observed concentration gradients in soil air and atmospheric air. Wood-degrading areas and soils with a humic layer were found to emit up to 1000 ng chloroform m⁻² h⁻¹ and seem to be larger chloroform sources than the other areas of study. Rather unexpectedly, some points of one sampling site appeared to emit 1,1,1-trichloroethane, tetrachloromethane and tetrachloroethene. A reasonable agreement was found between the fluxes using enclosures and those derived from the concentration gradients in soil air and atmospheric air.     

Effects of conditioning,cross‐conditioning,and microbial growth on development of enhanced biodegradation of insecticides in soil

Abstract

Pretreatment of a Drummer‐Catlin soil mixture with granular formulations of carbofuran or trimethacarb enhanced biodegradation of subsequent treatments with the technical formulations. Degradation of carbofuran was enhanced by pretreatments with trimethacarb, and degradation of trimethacarb was enhanced by pretreatments with carbofuran. Bendiocarb degradation was enhanced by pretreatments of soil with carbofuran or trimethacarb. In bioassays with southern corn rootworm larvae, biological activity of carbofuran, trimethacarb, and bendiocarb was rapidly lost in soils pretreated with granular formulations. Pretreatment of soil with granular terbufos did not enhance the biodegradation of subsequent applications of technical terbufos. Several microbial biomass assays showed an increase in specific carbofuran‐degrading bacteria in soils that were pretreated with carbofuran. Bacteria were isolated that could grow on carbofuran and apparently degrade it when present with another carbon source.     

Sorption of 17α-ethinyl estradiol, bisphenol A and phenanthrene to different size fractions of soil and sediment

The potential for negative effects caused by endocrine disrupting chemicals (EDCs) release into the environment is a prominent concern and numerous research projects have investigated possible environmental fate and toxicity. However, their sorption behavior by size fractions of soil and sediment has not been systematically represented. The sorption of bisphenol A (BPA), 17α-ethinyl estradiol (EE2) and phenanthrene (Phen) by different size fractions of soil and sediment were investigated. Sorption isotherms of EE2, BPA, and Phen by size fractions of soil (SL) and sediment (ST) were well fitted to the Freundlich model. The positive correlation between EE2, BPA and Phen sorption capacity (log K_d) of size fractions and their organic carbon (OC) content suggests that OC of size fractions in SL and ST should regulate sorption, while the surface area (SA) of size fractions may not account for sorption of EE2, BPA and Phen. Each size fraction of ST had higher sorption capacity (K_d or K_OC) of EE2 and BPA than that of SL due to their difference in the polarity of organic matter (OM) between terrestrial and aquatic sources. Sorption capacity logK_d for size fractions of SL and ST did not follow the order: clay > silt > sand due to the difference in OM abundance and composition between the size fractions. Large particle fractions of ST contributed about 80% to the overall sorption for any EE2, BPA, and Phen. This study was significant to evaluate size fractions of soil and sediment as well as their associated OM affecting EE2 and BPA sorption processes.     

Dissipation of chlorpyrifos,oxon, and 3,5,6‐trichloro‐2‐pyridinol in litter and elm forest soil

Abstract

After chlorpyrifos was applied to the basal 1 meter of elm tree trunks for control of elm bark beetles at two different application times and sites, initial chlorpyrifos residues in forest floor litter ranged from 120 to 916 μg/g depending on the application time. Residues dissipated by approximately 99% after 791 d with the DT₅₀ from 3.9 to 59 d and DT₉₀ from 55 to 310 d. The initial residues of chlorpyrifos in elm forest soil varied from 0.8 to 28 μg/g and were 1 to 2 μg/g at 791 d after application. The dissipation half‐lives of chlorpyrifos in fortified soil placed in the field ranged from 116 to 121 d.     

Degradation of atrazine,metolachlor, and pendimethalin in pesticide‐contaminated soils: Effects of aged residues on soil respiration and plant survival

Abstract

This study was conducted to determine the effects of pesticide mixtures on degradation patterns of parent compounds as well as effects on soil microbial respiration. Bioavailability of residues to sensitive plant species was also determined. Soil for this study was obtained from a pesticide‐contaminated area within an agrochemical dealer site. Degradation patterns were not affected by the presence or absence of other herbicides in this study. Atrazine concentrations were significantly lower at 21 through 160 days aging time compared to day 0 concentrations. Metolachlor and pendimethalin concentrations were not significantly different over time and remained high throughout the study. Microbial respiration was suppressed in treated soils from day 21 to day 160. Soybean and canola were the most successful plant species in the germination and survival tests. Generally, with increased aging of pesticides in soil, germination time decreased. Survival time of plants increased over time for some treatments indicating possible decreased bioavailability of pesticide residues. In some cases, survival time decreased at the longer 160‐day aging period, possibly indicating a change in bioavailability, perhaps as the result of formation of more bioavailable and phytotoxic metabolites. No interactive effects were noted for mixtures of pesticides compared to individually applied pesticides in terms of degradation of the parent compound or on seed germination, plant survival, or microbial respiration.     

The rate of soil reduction as affected by levels of methyl parathion and 2, 4‐D

Abstract

A simple technique was demonstrated for determining the potential for synthetic organics to stress microbial populations. Oxidized Crowley and Cecil soil materials were amended with varying concentrations of 2,4‐D and methyl parathion, flooded, and then analyzed for changes in pH, redox potential, and levels of soluble plus exchangeable Fe, Mn, and Zn, all of which may be directly or indirectly influenced by the activity of soil microorganisms. At the concentrations tested (up to 75 ppm), there was little effect of 2,4‐D, but methyl parathion apparently did affect microbial activity contributing to changes in the measured soil properties upon flooding. This approach may be a useful technique for screening various compounds for their potential to stress microbial activity that, for many researchers, would be easier than direct observations of microbial parameters such as population numbers and classifications, and enzyme levels.     

Mobility and phytoavailability of Cu,Cr, Zn,and As in a contaminated soil at a wood preservation site after 4 years of aided phytostabilization

The remediation of copper-contaminated soils by aided phytostabilisation in 16 field plots at a wood preservation site was investigated. The mobility and bioavailability of four potentially toxic trace elements (PTTE), i.e., Cu, Zn, Cr, and As, were investigated in these soils 4 years after the incorporation of compost (OM, 5 % w/w) and dolomite limestone (DL, 0.2 % w/w), singly and in combination (OMDL), and the transplantation of mycorrhizal poplar and willows. Topsoil samples were collected in all field plots and potted in the laboratory. Total PTTE concentrations were determined in soil pore water (SPW) collected by Rhizon soil moisture samplers. Soil exposure intensity was assessed by Chelex100-DGT (diffusive gradient in thin films) probes. The PTTE phytoavailability was characterized by growing dwarf beans on potted soils and analyzing their foliar PTTE concentrations. OM and DL, singly and in combination (OMDL), were effective to decrease foliar Cu, Cr, Zn, and As concentrations of beans, the lowest values being numerically for the OM plants. The soil treatments did not reduce the Cu and Zn mineral masses of the bean primary leaves, but those of Cr and As decreased for the OM and DL plants. The Cu concentration in SPW was increased in the OM soil and remained unchanged in the DL and OMDL soils. The available Cu measured by DGT used to assess the soil exposure intensity correlated with the foliar Cu concentration. The Zn concentrations in SPW were reduced in the DL soil. All amendments increased As in the SPW. Based on DGT data, Cu availability was reduced in both OM and OMDL soils, while DL was the most effective to decrease soil Zn availability.     

Estimation of β-cyfluthrin and imidacloprid in okra fruits and soil by chromatography techniques

Dissipation of β-cyfluthrin and imidacloprid in okra was studied following three applications of a combination formulation of Solomon 300 OD (β-cyfluthrin 9 % + imidacloprid 21 %) @ 60 and 120 g a.i. ha^?1 at 7 days interval. Residues of β-cyfluthrin and imidacloprid in okra were estimated by gas liquid chromatography (GLC) and high performance liquid chromatography (HPLC), respectively. Residues of β-cyfluthrin were confirmed by gas chromatograph–mass spectrometry (GC-MS) and that of imidacloprid by high performance thin layer chromatography (HPTLC). Half-life periods for β-cyfluthrin were found to be 0.91 and 0.68 days whereas for imidacloprid these values were observed to be 0.85 and 0.96 days at single and double the application rates, respectively. Residues of β-cyfluthrin dissipated below its limit of quantification (LOQ) of 0.01 mg kg^?1 after 3 and 5 days at single and double the application dosage, respectively. Similarly, residues of imidacloprid took 5 and 7 days to reach LOQ of 0.01 mg kg^?1, at single and double dosages respectively. Soil samples collected after 15 days of the last application did not show the presence of β-cyfluthrin and imidacloprid at their detection limit of 0.01 mg kg^?1.     

Remediation of heavy metal–polluted alkaline vegetable soil using mercapto-grafted palygorskite: effects of field-scale application and soil environmental quality

Environmental Science and Pollution Research - Remediation materials are the most critical factors for in situ immobilization of soil contaminated by heavy metals. In this study, in order to...     

Effects of alternative electron donors,acceptors, and inhibitors on 2,4‐dichlorophenoxyacetic acid and 2,4,5‐trichlorophenoxyacetic acid dechlorination in soil

Abstract

The potential for dechlorinating 2,4‐dichlorophenoxyacetic acid (2,4‐D) and 2,4,5‐trichlorophenoxyacetic acid (2,4,5‐T) in soil with a consortium showing stable dechlorinating activity was investigated. The effects of adding electron donors and/or acceptors under three anaerobic reducing conditions was compared. Results show that both 2,4‐D and 2,4,5‐T dechlorination rates were enhanced in methanogenic conditions, delayed in sulfate‐reducing conditions, and inhibited in denitrifying conditions. Also under the same three conditions dechlorination was be enhanced by the addition of lactate, pyruvate, and acetate, delayed by the addition of manganese oxide and vitamin B₁₂, and inhibited by the addition of ferric chloride. Response to treatment with such microbial inhibitors as bromoethane sulfonic acid (BESA), vancomycin, and molybdate suggests that the major bacteria involved in 2,4‐D and 2,4,5‐T dechlonnation is methanogen followed joined by sulfate‐reducing bacteria and eubacteria.     

Estimation of β-cyfluthrin and imidacloprid in okra fruits and soil by chromatography techniques

Dissipation of β-cyfluthrin and imidacloprid in okra was studied following three applications of a combination formulation of Solomon 300 OD (β-cyfluthrin 9 % + imidacloprid 21 %) @ 60 and 120 g a.i. ha(-1) at 7 days interval. Residues of β-cyfluthrin and imidacloprid in okra were estimated by gas liquid chromatography (GLC) and high performance liquid chromatography (HPLC), respectively. Residues of β-cyfluthrin were confirmed by gas chromatograph-mass spectrometry (GC-MS) and that of imidacloprid by high performance thin layer chromatography (HPTLC). Half-life periods for β-cyfluthrin were found to be 0.91 and 0.68 days whereas for imidacloprid these values were observed to be 0.85 and 0.96 days at single and double the application rates, respectively. Residues of β-cyfluthrin dissipated below its limit of quantification (LOQ) of 0.01 mg kg(-1) after 3 and 5 days at single and double the application dosage, respectively. Similarly, residues of imidacloprid took 5 and 7 days to reach LOQ of 0.01 mg kg(-1), at single and double dosages respectively. Soil samples collected after 15 days of the last application did not show the presence of β-cyfluthrin and imidacloprid at their detection limit of 0.01 mg kg(-1).     

Influence of hydroxypropyl-β-cyclodextrin on the biodegradation of C-phenanthrene and C-hexadecane in soil

Soil was spiked with [9-¹⁴C]phenanthrene and [1-¹⁴C]hexadecane at 50 mg kg⁻¹ and aged for 1, 25, 50, 100 and 250 d. At each time point, the microcosms were amended with aqueous solutions of cyclodextrin (HP-β-CD) at a range of concentrations (0-40 mM). Mineralisation assays and aqueous HP-β-CD extractions were performed to assess the effect of the amendments on microbial degradation. The results showed that amendments had no significant impact on the microbial degradation of either of the ¹⁴C-contaminants. Further, HP-β-CD extractions were correlated with the mineralisation of the target chemicals in each of the soil conditions. It was found that the HP-β-CD extraction was able to predict mineralisation in soils which had not been amended with cyclodextrin; however, in the soils containing the HP-β-CD, there was no predictive relationship. Under the conditions of this study, the introduction of HP-β-CD into soils did not enhance the biodegradation of the organic contaminants.     

Laboratory studies of dissipation of 14C‐DDT from soil and plywood surfaces

Abstract

The effects of temperature and solar radiation on dissipation of ¹⁴C‐p,p'‐DDT from a latosol soil were studied under laboratory conditions. Volatilization was measured by trapping organic volatiles during 6 weeks and was found to increase with rise of temperature from 3.8% of initial amount at ambient temperature to 5.9% at 45°C.

Studies on the effect of solar radiation using quartz tubes under sterilized and non‐sterilized conditions have shown that volatilized organics were highest in quartz tubes, with soil microflora presumably playing a very minor role in volatilization. Mineralization was shown to be low in sterilized systems and highest in non‐sterilized quartz systems. Studies on binding suggest that soil bioactivity may be involved in the formation of a portion of the bound residue. These laboratory experiments seem to support data from the field, where it is maintained that volatilization is a major mechanism for dissipation. Degradation in soil and to a lesser extent solar irradiation contribute also substantially to the dissipation mechanisms. Radiocarbon dissipated from plywood surfaces under indoor conditions in a biphasic fashion. Loss of 50% occurred after 5.5 weeks while the remainder dissipated at a very slow rate.     

Laboratory studies on volatilization and mineralization of 14c‐p,p'‐DDT in soil,release of bound residues and dissipation from solid surfaces

Abstract

In support of field data, laboratory studies were conducted on volatilization, mineralization and binding of ¹⁴C‐p,p'‐DDT in soils at Sao Paulo. Incubation of soil for 6 weeks did not result in volatilized organics or mineralization; with >95% extractable radiocarbon in the form of p,p'‐DDT. Small amounts of bound residues (1.8%) were detected in soil. These data confirm the very slow dissipation of DDT in the field which presumably relates to the acidic pH of soil (4.5–4.8).

Bound ¹⁴C‐residues in soils treated with ¹⁴C‐p,p'‐DDT at Praia Grande and Sao Paulo could be released (5–21%) by sulphuric acid treatment. The released residue had the composition: 69–90% DDT, 7–32% DDD and 0–3% DDE. Incubation of soil bound ¹⁴C‐residues with fresh inoculum for 3 months did not result in release of ¹⁴C.

Dissipation from wooden surfaces was fairly slow. After 20 weeks, 74% of the applied radioactivity could be recovered; 44% hexane‐non‐extractable.     

Concentrations,atmospheric partitioning,and air–water/soil surface exchange of polychlorinated dibenzo-p-dioxin and dibenzofuran along the upper reaches of the Haihe River basin,North China

Polychlorinated dibenzo-p-dioxin and dibenzofuran (PCDD/PCDF) were overall measured and compared in ambient air, water, soils, and sediments along the upper reaches of the Haihe River of North China, so as to evaluate their concentrations, profiles, and to understand the processes of gas–particle partitioning and air–water/soil exchange. The following results were obtained: (1) The average concentrations (toxic equivalents, TEQs) of 2,3,7,8-PCDD/PCDF in air, water, sediment, and soil samples were 4,855 fg/m³, 9.5 pg/L, 99.2 pg/g dry weight (dw), and 56.4 pg/g (203 fg TEQ/m³, 0.46 pg TEQ/L, 2.2 pg TEQ/g dw, and 1.3 pg TEQ/g, respectively), respectively. (2) Although OCDF, 1,2,3,4,6,7,8-HpCDF, OCDD, and 1,2,3,4,6,7,8-HpCDD were the dominant congeners among four environmental sinks, obvious discrepancies of these congener and homologue patterns of PCDD/PCDF were observed still. (3) Significant linear correlations for PCDD/PCDF were observed between the gas–particle partition coefficient (K _p) and the subcooled liquid vapor pressure (P _L ⁰) and octanol–air partition coefficient (K _oa). (4) Fugacity fraction values of air–water exchange indicated that most of PCDD/PCDF homologues were dominated by net volatilization from water into air. The low-chlorinated PCDD/PCDF (tetra- to hexa-) presented a strong net volatilization from the soil into air, while high-chlorinated PCDD/PCDF (hepta- to octa-) were mainly close to equilibrium for air–soil exchange.     

Preparation of petroleum-degrading bacterial agent and its application in remediation of contaminated soil in Shengli Oil Field,China

Two petroleum-degrading strains were screened from oil fields and denoted as SWH-1 (Bacillus subtilis) and SWH-2 (Sphingobacterium multivorum), which were used to ferment and prepare bacterial agent to remediate petroleum-contaminated sites in Shengli Oil Field in China. The optimal liquid fermentation medium and conditions were MgSO₄·7H₂O (0.5 %), NaCl (0.5 %), soybean dregs (3 %), pH 7.0, culturing at 30 °C, and 220 r/min for 16 h. Peat was chosen as the bacterial carrier due to its ability of keeping microbial activity. Mixed fermented liquid was added into peat (1:2) and air-dried, and the bacterial agent was obtained. It was applied to the petroleum-contaminated soil, which was irrigated, tilled, and fertilized. The removal rate reached 67.7 % after 2 months of remediation. During remediation, the quantity of indigenous bacteria varied a lot, while the inoculated bacteria remained stable; the dehydrogenase activity was at high levels and then decreased. Indigenous microorganisms, inoculated bacterial agent, nutrients, water, and soil permeability all played important roles. The study prepared an environment-friendly bacterial agent and established a set of bioremediation technique, which provided further insights into integration of fermentation engineering and soil remediation engineering.     

Biodegradation of malathion, α- and β-endosulfan by bacterial strains isolated from agricultural soil in Veracruz,Mexico

The objective of this study was to evaluate the capacity of two bacterial strains isolated, cultivated, and purified from agricultural soils of Veracruz, Mexico, for biodegradation and mineralisation of malathion (diethyl 2-(dimethoxyphosphorothioyl) succinate) and α- and β-endosulfan (6,7,8,9,10,10-hexachloro-1,5,5a,6,9,9a-hexahydro-6-9-methano-2,4,3-benzodioxathiepine-3-oxide). The isolated bacterial strains were identified using biochemical and morphological characterization and the analysis of their 16S rDNA gene, as Enterobacter cloacae strain PMM16 (E1) and E. amnigenus strain XGL214 (M1). The E1 strain was able to degrade endosulfan, whereas the M1 strain was capable of degrading both pesticides. The E1 strain degraded 71.32% of α-endosulfan and 100% of β-endosulfan within 24 days. The absence of metabolites, such as endosulfan sulfate, endosulfan lactone, or endosulfan diol, would suggest degradation of endosulfan isomers through non-oxidative pathways. Malathion was completely eliminated by the M1 strain. The major metabolite was butanedioic acid. There was a time-dependent increase in bacterial biomass, typical of bacterial growth, correlated with the decrease in pesticide concentration. The CO₂ production also increased significantly with the addition of pesticides to the bacterial growth media, demonstrating that, under aerobic conditions, the bacteria utilized endosulfan and malathion as a carbon source. Here, two bacterial strains are shown to metabolize two toxic pesticides into non-toxic intermediates.     

Determination of cyclic volatile methylsiloxanes in water,sediment, soil,biota, and biosolid using large-volume injection–gas chromatography–mass spectrometry

Several methods were developed to detect the cyclic volatile methylsiloxanes (cVMSs) including octamethylcyclotetrasiloxane (D4), decamethylcyclopentasiloxane (D5), and dodecamethylcyclohexasiloxane (D6) in water, sediment, soil, biota, and biosolid samples. Analytical techniques employed to optimize measurement of this compound class in various matrices included membrane-assisted solvent extraction in water, liquid–solid extraction for sediment, soil, biota, and biosolid samples. A subsequent analysis of the extract was conducted by large-volume injection–gas chromatography−mass spectrometry (LVI−GC−MS). These methods employed no evaporative techniques to avoid potential losses and contamination of the volatile siloxanes. To compensate for the inability to improve detection limits by concentrating final sample extract volumes we used a LVI–GC–MS. Contamination during analysis was minimized by using a septumless GC configuration to avoid cVMS’s associated with septum bleed. These methods performed well achieving good linearity, low limits of detection, good precision, recovery, and a wide dynamic range. In addition, stability of cVMS in water and sediment was assessed under various storage conditions. D4 and D5 in Type-I (Milli-Q) water stored at 4 °C were stable within 29 d; however, significant depletion of D6 (60–70%) occurred only after 3 d. Whereas cVMS in sewage influent and effluent were stable at 4 °C within 21 d. cVMS in sediment sealed in amber glass jars at −20 °C and in pentane extracts in vials at −15 °C were stable during 1 month under both storage conditions.     

Residues of chlorpyrifos‐methyl in balsam fir foliage,forest litter,soil, stream water,sediment and fish tissue after double aerial applications of Reldan®

Abstract

Chlorpyrifos‐methyl was applied twice at 70 g A.I./ha by means of a fixed‐wing aircraft to a mixed coniferous forest near Allardville, New Brunswick. Residue in balsam fir foliage was highest (1 ppm wet wt) 1 hr after spraying and rapidly declined to about 30% within 1 day, but persisted at a very low level (0.03 ppm wet wt) for 125 days. Current year's foliage contained a higher level of residue than old foliage. Chlorpyrifos‐methyl persisted longer in forest litter than in soil. After 125 days, trace amounts (< 6 ppb wet wt) were still found in litter but were not detected in soil. In stream water the residue dissipated very rapidly; more than 90% disappeared 3 hours after the second application and were not detected after 4 days. Low‐level residue (< 0.1 ppm wet wt) was present in the sediment and persisted for 10 days. Although brook trout and slimy sculpin captured in the stream within 3 days of the second application contained residues (< 0.05 ppm fresh wt) none were detected in any fish captured, 9 and 47 days later.