Metal toxicity assessment of mobile phone parts using Milli Q water

Environmentally safe disposal of end-of-life (EoL) or discarded mobile phone is a serious problem on account of their ever increasing number and toxic metals contents. In the present work, metal toxicity of mobile phone plastics, printed wire boards (PWBs) and batteries were assessed through dynamic batch leaching using Milli Q (MQ) water. Phone plastics failed Toxicity Characterization Leaching Procedure (TCLP) and Waste Extraction Test (WET) for Pb as the cumulative amount of Pb leached from plastics (5.33 mg/l) exceeded the regulatory limits (5.0 mg/l) used in characterizing a waste as hazardous. Similarly, the average cumulative amount (21.83 mg/l) of Ni leached from PWBs exceeded the regulatory limit of 20 mg/l and thus PWBs failed WET. Metals leached from batteries in small amounts (Cr: 0.40 mg/l and Ni: 0.15 mg/l). The presence of Fe in the batteries and its precipitation as oxides/hydroxides in the leaching solution hindered the leaching of other metals in MQ water. Both plastics and PWBs should be treated as hazardous waste and should not be disposed in open landfills. Further, MQ water leaching could provide good simulation of metals leaching from the mobile phones disposed at landfill sites.     

Stabilization of heavy metals in MSWI fly ash using silica fume

The objective of this work was to investigate the feasibility and effectiveness of silica fume on stabilizing heavy metals in municipal solid waste incineration (MSWI) fly ash. In addition to compressive strength measurements, hydrated pastes were characterized by X-ray diffraction (XRD), thermal-analyses (DTA/TG), and MAS NMR (²⁷Al and ²⁹Si) techniques. It was found that silica fume additions could effectively reduce the leaching of toxic heavy metals. At the addition of 20% silica fume, leaching concentrations for Cu, Pb and Zn of the hydrated paste cured for 7 days decreased from 0.32 mg/L to 0.05 mg/L, 40.99 mg/L to 4.40 mg/L, and 6.96 mg/L to 0.21 mg/L compared with the MSWI fly ash. After curing for 135 days, Cd and Pb in the leachates were not detected, while Cu and Zn concentrations decreased to 0.02 mg/L and 0.03 mg/L. The speciation of Pb and Cd by the modified version of the European Community Bureau of Reference (BCR) extractions showed that these metals converted into more stable state in hydrated pastes of MSWI fly ash in the presence of silica fume. Although exchangeable and weak-acid soluble fractions of Cu and Zn increased with hydration time, silica fume addition of 10% can satisfy the requirement of detoxification for heavy metals investigated in terms of the identification standard of hazardous waste of China.     

Hospital waste management in Libya: A case study

In Libya, as in many developing countries, little information is available regarding generation, handling and disposal of hospital waste. This fact hinders the development and implementation of hospital waste management schemes. The specific objective of this study is to present an appraisal of the current situation regarding hospital waste management in Libya. Procedures, techniques, methods of handling, and disposal of waste are presented, as well as the amounts and compositions of hospital waste. This research was conducted in the form of a case study. Fourteen different healthcare facilities in three cities, Tripoli, Misurata, and Sirt, all located in the northwestern part of Libya, were selected for investigation. The investigation showed that the hospitals surveyed had neither guidelines for separated collection and classification, nor methods for storage and disposal of generated waste. This deficiency indicates the need for an adequate hospital waste management strategy to improve and control the existing situation. The average waste generation rate was found to be 1.3 kg/patient/day, comprised of 72% general healthcare waste (non-risk) and 28% hazardous waste. The average general waste composition was: 38% organic, 24% plastics, and 20% paper. Sharps and pathological elements comprised 26% of the hazardous waste component.     

Correlation study of hazardous waste characteristics among various chemical processes in Republic of Korea

To harmonize with international standards, the Republic of Korea is in the process of converting its current hazardous waste classification system and setting up regulatory standards for all toxic substances present in hazardous waste. Detailed characterization of each form of hazardous waste belonging to five chemical processes and their correlations were studied. In the present work, the concentrations of 13 heavy metals, F^?, CN^?, 7 PAH compounds, total PCDD/F and 7 PCB isomers present in the hazardous waste generated among chemical processes such as synthetic rubber (SR), man-made fibers (MF), organic dyes and pigments (DP), pharmaceuticals and cosmetics were analyzed along with their leaching characteristics. Comparing all the processes, most of the heavy metal concentrations were high in SR waste. Naphthalene was the dominant PAH in most of the chemical process waste. PCDD/F concentrations of the samples were in the range of 0.001–0.003 ng I-TEQ/g. PCB isomer-101 and isomer-118 were found to be slightly higher than the permissible limit in the SR filter cake sample. SR process wastes doesn’t show any resemblance with the other process waste in either the heavy metals and PAH trend. Each sample from DP and MF were suitable only for hazardous waste landfill.     

Precious metals and rare earth elements in municipal solid waste – Sources and fate in a Swiss incineration plant

In Switzerland many kinds of waste, e.g. paper, metals, electrical and electronic equipment are separately collected and recycled to a large extent. The residual amount of municipal solid waste (MSW) has to be thermally treated before final disposal. Efforts to recover valuable metals from incineration residues have recently increased. However, the resource potential of critical elements in the waste input (sources) and their partitioning into recyclable fractions and residues (fate) is unknown. Therefore, a substance flow analysis (SFA) for 31 elements including precious metals (Au, Ag), platinum metal group elements (Pt, Rh) and rare earth elements (La, Ce, etc.) has been conducted in a solid waste incinerator (SWI) with a state-of-the-art bottom ash treatment according to the Thermo-Re® concept. The SFA allowed the determination of the element partitioning in the SWI, as well as the elemental composition of the MSW by indirect analysis. The results show that the waste-input contains substantial quantities of precious metals, such as 0.4 ± 0.2 mg/kg Au and 5.3 ± 0.7 mg/kg Ag. Many of the valuable substances, such as Au and Ag are enriched in specific outputs (e.g. non-ferrous metal fractions) and are therefore recoverable. As the precious metal content in MSW is expected to rise due to its increasing application in complex consumer products, the results of this study are essential for the improvement of resource recovery in the Thermo-Re® process.     

GHG emission factors developed for the recycling and composting of municipal waste in South African municipalities

GHG (greenhouse gas) emission factors for waste management are increasingly used, but such factors are very scarce for developing countries. This paper shows how such factors have been developed for the recycling of glass, metals (Al and Fe), plastics and paper from municipal solid waste, as well as for the composting of garden refuse in South Africa. The emission factors developed for the different recyclables in the country show savings varying from ?290 kg CO₂ e (glass) to ?19 111 kg CO₂ e (metals – Al) per tonne of recyclable. They also show that there is variability, with energy intensive materials like metals having higher GHG savings in South Africa as compared to other countries. This underlines the interrelation of the waste management system of a country/region with other systems, in particular with energy generation, which in South Africa, is heavily reliant on coal. This study also shows that composting of garden waste is a net GHG emitter, releasing 172 and 186 kg CO₂ e per tonne of wet garden waste for aerated dome composting and turned windrow composting, respectively. The paper concludes that these emission factors are facilitating GHG emissions modelling for waste management in South Africa and enabling local municipalities to identify best practice in this regard.     

Waste plastics recycling by an entrained-flow gasifier

We studied an entrained-flow gasification process which efficiently converts waste plastics to energy at a high energy recovery rate. Waste plastics, after being shredded to <8 mm or <14 mm, were fed into an entrained-flow gasifier with air and oxygen. In the gasifier, organic substances were pyrolyzed, partially combusted, and then converted into synthetic gas (CO, H₂) at a high temperature (over 1600 K). The clarified gasification characteristics were that the lower heat value (LHV) of the product gas was over 4.2 MJ/Nm³ and the cold gas efficiency was approximately 60%. Other inert substances in the wastes such as ashes and metals were melted into slag and condensed on bag filters. The bag filters and a water scrubber removed impurities such as dusts, heavy metals, and hydrogen halides from the product gases. Solid hydrocarbons, which include char and soot, were removed at a hot cyclone and on the bag filters. Received: July 19, 2000 / Accepted: October 3, 2000     

Survey of composition and generation rate of household wastes in Beijing, China

It is recognized that information on both quantity and composition of residential waste is important for the effective planning of household waste handling infrastructure. In this paper, we present the results of a survey on household waste generation and composition in Beijing, China. Sample communities were selected by the integration of five indices including family population, income, age, and education. Wastes were sampled on a daily basis from 113 households in six different districts of Beijing City for ten days. The results showed that the generation rate of household wastes was 0.23 kg/pers/day. The bulk density was approximately 221 kg/m³, and the moisture content was approximately 50%. Household waste consisted of kitchen waste, paper/cardboard, plastics, textiles, metals, glass and other wastes, the proportion of each waste was approximately 69.3%, 10.3%, 9.8%, 1.3%, 0.8%, 0.6% and 2.7%, respectively. An evaluation of the relationship between daily per capita generation of household waste and socio-economic factors indicated that household size and income both showed a negative relationship with household waste generation (kg/pers/day). As for the effect of education, families with a secondary educational level produced fewer household wastes (kg/pers/day) than those with a primary or advanced educational level.     

Waste on the roadside, 'poi-sute' waste: its distribution and elution potential of pollutants into environment

Waste on the roadside, 'poi-sute' waste, was collected in a typical suburb in Japan (Ueda city, the sampling course: 3.2 km). The distribution, characterization of the 'poi-sute' waste and the loading of pollutants from the waste were studied. The average number of pieces of total waste was 690 pieces a month, and 220 pieces of waste were dumped a month per km. There was a tendency for much waste to be discarded around shops staying open until late at night. Regarding the sorts of the waste, cigarette butts are the most prevalent (the average was 150 cigarette butts/km/mo), and second was plastic materials. As for the weight, cigarette butts, plastics and papers were at a similar level (about 90 g/km/mo). The elution of arsenic (0.041 mg/L) and nicotine (3.8 mg/L) was ascertained by a dissolution test of 'poi-sute' cigarette butts obtained by sampling. Furthermore, the loading of heavy metals, such as lead, copper, chromium and cadmium, and polycyclic aromatic hydrocarbons (PAHs) from cigarette butts into the environment was confirmed. The load potentials of heavy metals were 0.020-1.7 mg/km/mo, and that of total-polyaromatic hydrocarbons was 0.032 mg/km/mo. These results indicate that the 'poi-sute' waste has a harmful influence on the environment.     

Biosorption study of potential fungi for copper remediation from Peninsular Malaysia

The ability to grow in heavy metal contaminated areas and absorb heavy metals from the environment make fungi a potentially viable biological‐based technology for remediating hazardous heavy metals in soil. In this study, 10 fungi from a copper (Cu)‐polluted area in Malaysia were isolated, with the four highest growth fungi identified as Simplicillium subtropicum, Fusarium solani, Aspergillus tamari, and Aspergillus niger. Results from toxicity and biosorption testing showed that A. niger and F. solani grew the fastest in the presence of Cu, but exhibited lower Cu uptake per unit of biomoass. In contrast, A. tamarii and S. subtropicum had lower growth rates, but showed better uptake of Cu per unit of biomass. S. subtropicum was identified as the best species for bioremediation because it had the highest Cu uptake and positive growth measured in the presence of Cu at concentrations below 100 mg/L. A niger proved to be most suitable for bioremediation if the concentration of Cu exceeds 100 mg/L.     

Characterization of air emissions and residual ash from open burning of electronic wastes during simulated rudimentary recycling operations

Air emissions and residual ash samples were collected and analyzed during experiments of open, uncontrolled combustion of electronic waste (e-waste), simulating practices associated with rudimentary e-waste recycling operations. Circuit boards and insulated wires were handled separately to simulate processes associated with metal recovery. The average emissions of polychlorinated dibenzodioxins and dibenzofurans (PCDD/PCDFs) were 92 ng toxic equivalency (TEQ)/kg [n = 2, relative standard deviation (RSD) = 98%] and 11 900 ng TEQ/kg (n = 3, RSD = 50%) of the initial mass of the circuit boards and insulated wire, respectively. The value for the insulated wire is about 100 times higher than that for backyard barrel burning of domestic waste. The emission concentrations of polybrominated dibenzodioxins and dibenzofurans (PBDD/PBDFs) from the combustion of circuit boards were 100 times higher than for their polychlorinated counterparts. Particulate matter (PM) sampling of the fly ash emissions indicated PM emission factors of approximately 15 and 17 g/kg of the initial mass for the circuit boards and insulated wire, respectively. Fly ash samples from both types of e-waste contained considerable amounts of several metallic elements and halogens; lead concentrations were more than 200 times the United States regulatory limits for municipal waste combustors and 20 times those for secondary lead smelters. Leaching tests of the residual bottom ash showed that lead concentrations exceeded U.S. Environmental Protection Agency landfill limits, designating this ash as a hazardous waste.     

Thiourea leaching of gold from processed municipal solid waste incineration residues

Incineration is one of the key technologies in disposal of municipal waste, which produces municipal solid waste incineration (MSWI) residues with high valuable metal contents. The recycling strategy for the MSWI residues is typically focused on the recovery of scrap metals yielding processed municipal solid waste incineration residues (PIR) as the main byproduct. However, the PIR still contains valuable metals, particularly gold, which cannot be extracted by conventional methods. Here, we evaluated the feasibility of using the 0.5–2.0 mm grain size fraction of PIR containing 28.82 ± 1.62 mg/kg of gold as raw material for a two-stage extraction process. In the first stage the alkalic fine-grained PIR was acidified with a solution of 20% (v/v) of HCl-containing flue gas cleaning liquid that is obtained by the municipal waste incineration plant itself as a waste product. In the second stage we leached the acidified fine-grained PIR by thiourea with Fe³⁺ as an oxidant. Application of the thiourea-Fe³⁺ leaching system resulted in recovery of 16.4 ± 1.56 mg/kg of gold from the fine-grained PIR within 6 h of incubation. Due to high gold market prices, upscaling of the suggested technology can represent a suitable strategy for gold recovery from PIR and other MSWI residues.

     

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.     

Characterization of a thermal power plant air heater washing waste: a case study from Iran.

In Iran most of the electricity is generated by thermal power plants. As a result of fuel oil burning in winter time, the air heaters of the boilers have to be washed and cleaned frequently. The wastewater originating from air heater washing is then treated in an effluent treatment plant by chemical precipitation followed by dewatering of the sludge produced. The resulting waste is classified as specific industrial waste that should be characterized in detail under the Waste Management Act of Iran. The quantity of this waste produced in the studied power plant is about 20 tonnes year(-1). In the present investigation, the first to be carried out in Iran, seven composite samples of dewatered sludge from air heater washing wastewater treatment were subjected to investigation of the physical properties, chemical composition and leaching properties. The most likely pollutants that were of concern in this study were heavy and other hazardous metals (Cd, Co, Cr, Mn, Ni, Pb, Zn and V). The results revealed that mean pH, wet and dry density and moisture content of the waste were 6.31, 1532 kg m(-30, 1879 kg m(-3) and 15.35%, respectively. Magnetite, SiO2, P2O5, CaO, Al2O3 and MgO were the main constituents of the waste with a weight percentage order of 68.88, 5.91, 3.39, 2.64, 2.59 and 1.76%, respectively. The toxicity characteristic leaching procedure test results for some heavy and other hazardous metals showed that mean elemental concentrations of Cd, Co, Cr, Mn, Ni, Pb, V and Zn in leachate were 0.06, 1.55, 5.49, 36.32, 209.10, 0.58, 314.06 and 24.84 mg L(-1), respectively. According to the Waste Management Act of Iran this waste should be classified as hazardous and should be disposed of in accordance with hazardous waste disposal regulations.     

Tank-connected food waste disposer systems – Current status and potential improvements

An unconventional system for separate collection of food waste was investigated through evaluation of three full-scale systems in the city of Malmö, Sweden. Ground food waste is led to a separate settling tank where food waste sludge is collected regularly with a tank-vehicle. These tank-connected systems can be seen as a promising method for separate collection of food waste from both households and restaurants. Ground food waste collected from these systems is rich in fat and has a high methane potential when compared to food waste collected in conventional bag systems. The content of heavy metals is low. The concentrations of N-tot and P-tot in sludge collected from sedimentation tanks were on average 46.2 and 3.9 g/kg TS, equalling an estimated 0.48 and 0.05 kg N-tot and P-tot respectively per year and household connected to the food waste disposer system. Detergents in low concentrations can result in increased degradation rates and biogas production, while higher concentrations can result in temporary inhibition of methane production. Concentrations of COD and fat in effluent from full-scale tanks reached an average of 1068 mg/l and 149 mg/l respectively over the five month long evaluation period. Hydrolysis of the ground material is initiated between sludge collection occasions (30 days). Older food waste sludge increases the degradation rate and the risks of fugitive emissions of methane from tanks between collection occasions. Increased particle size decreases hydrolysis rate and could thus decrease losses of carbon and nutrients in the sewerage system, but further studies in full-scale systems are needed to confirm this.     

Chromium in soil layers and plants on closed landfill site after landfill leachate application

Landfill leachate (LL) usually contains low concentrations of heavy metals due to the anaerobic conditions in the methanogenic landfill body after degradation of easily degradable organic matter and the neutral pH of LL, which prevents mobilization and leaching of metals. Low average concentrations of metals were also confirmed in our extensive study on the rehabilitation of an old landfill site with vegetative landfill cover and LL recirculation after its treatment in constructed wetland. The only exception was chromium (Cr). Its concentrations in LL ranged between 0.10 and 2.75 mg/L, and were higher than the concentrations usually found in the literature. The objectives of the study were: (1) to understand why Cr is high in LL and (2) to understand the fate and transport of Cr in soil and vegetation of landfill cover due to known Cr toxicity to plants. The total concentration of Cr in LL, total and exchangeable concentrations of Cr in landfill soil cover and Cr content in the plant material were extensively monitored from May 2004 to September 2006. By obtained data on Cr concentration in different landfill constituents, supported with the data on the amount of loaded leachate, amount of precipitation and potential evapotranspiration (ETP) during the performance of the research, a detailed picture of time distribution and co-dependency of Cr is provided in this research. A highly positive correlation was found between concentrations of Cr and dissolved organic carbon (r = 0.875) in LL, which indicates the co-transport of Cr and dissolved organic carbon through the system. Monitoring results showed that the substrate used in the experiment did not contribute to Cr accumulation in the landfill soil cover, resulting in percolation of a high proportion of Cr back into the waste layers and its circulation in the system. No negative effects on plant growth appeared during the monitoring period. Due to low uptake of Cr by plants (0.10–0.15 mg/kg in leaves and 0.05–0.07 mg/kg in stems of Salix purpurea), the estimated Cr offtake from LL by plants represented only a small proportion of the LL Cr mass load during the observation period, resulting in no dispersion of Cr into the environment through leaf drop.     

Heavy metal content of combustible municipal solid waste in Denmark.

Data on the heavy metal composition of outlets from Danish incinerators was used to estimate the concentration of Zn, Cu, Pb, Cr, Ni, Cd, As and Hg in combustible waste (wet as received) at 14 Danish incinerators, representing about 80% of the waste incinerated in Denmark. Zn (1020 mg kg(-1)), Cu (620 mg kg(-1)) and Pb (370 mg kg(-1)) showed the highest concentration, whereas Hg (0.6 mg kg(-1)) showed the lowest concentration. The variation among the incinerators was in most cases within a factor of two to three, except for Cr that in two cases showed unexplained high concentrations. The fact that the data represent many incinerators and, in several cases, observations from a period of 4 to 5 years provides a good statistical basis for evaluating the content of heavy metals in combustible Danish waste. Such data may be used for identifying incinerators receiving waste with high concentrations of heavy metals suggesting the introduction of source control, or, if repeated in time, the data must also be used for monitoring the impacts of national regulation controlling heavy metals. It is recommended that future investigations consider the use of sample digestion methods that ensure complete digestion in order to use the data for determining the total heavy metal content of waste.     

Composition and production rate of medical waste from a small producer in Greece

The objective of this work was to determine the composition and production rate of medical waste from the health care facility of social insurance institute, a small waste producer in Xanthi, Greece. Specifically, produced medical waste from the clinical pathology (medical microbiology) laboratory, the X-ray laboratory and the surgery and injection therapy departments of the health facility was monitored for six working weeks. A total of 240 kg medical solid waste was manually separated and weighed and 330 L of liquid medical waste was measured and classified. The hazardous waste fraction (%w/w) of the medical solid waste was 91.6% for the clinical pathology laboratory, 12.9% for the X-ray laboratory, 24.2% for the surgery departments and 17.6% for the injection therapy department. The infectious waste fraction (%w/w) of the hazardous medical solid waste was 75.6% for the clinical pathology laboratory, 0% for the X-ray laboratory, 100% for the surgery departments and 75.6% for the injection therapy department. The total hazardous medical solid waste production rate was 64 ± 15 g/patient/d for the clinical pathology laboratory, 7.2 ± 1.6 g/patient/d for the X-ray laboratory, 8.3 ± 5.1 g/patient/d for the surgery departments and 24 ± 9 g/patient/d for the injection therapy department. Liquid waste was produced by the clinical pathology laboratory (infectious-and-toxic) and the X-ray laboratory (toxic). The production rate for the clinical pathology laboratory was 0.03 ± 0.003 L/patient/d and for the X-ray laboratory was 0.06 ± 0.006 L/patient/d. Due to the small amount produced, it was suggested that the most suitable management scheme would be to transport the hazardous medical waste, after source-separation, to the Prefectural Hospital of Xanthi to be treated with the hospital waste. Assuming this data is representative of other small medical facilities, medical waste production can be estimated for such facilities distributed around Greece.     

Recycling of non-metallic fractions from waste electrical and electronic equipment (WEEE): A review

The world’s waste electrical and electronic equipment (WEEE) consumption has increased incredibly in recent decades, which have drawn much attention from the public. However, the major economic driving force for recycling of WEEE is the value of the metallic fractions (MFs). The non-metallic fractions (NMFs), which take up a large proportion of E-wastes, were treated by incineration or landfill in the past. NMFs from WEEE contain heavy metals, brominated flame retardant (BFRs) and other toxic and hazardous substances. Combustion as well as landfill may cause serious environmental problems. Therefore, research on resource reutilization and safe disposal of the NMFs from WEEE has a great significance from the viewpoint of environmental protection. Among the enormous variety of NMFs from WEEE, some of them are quite easy to recycle while others are difficult, such as plastics, glass and NMFs from waste printed circuit boards (WPCBs). In this paper, we mainly focus on the intractable NMFs from WEEE. Methods and technologies of recycling the two types of NMFs from WEEE, plastics, glass are reviewed in this paper. For WEEE plastics, the pyrolysis technology has the lowest energy consumption and the pyrolysis oil could be obtained, but the containing of BFRs makes the pyrolysis recycling process problematic. Supercritical fluids (SCF) and gasification technology have a potentially smaller environmental impact than pyrolysis process, but the energy consumption is higher. With regard to WEEE glass, lead removing is requisite before the reutilization of the cathode ray tube (CRT) funnel glass, and the recycling of liquid crystal display (LCD) glass is economically viable for the containing of precious metals (indium and tin). However, the environmental assessment of the recycling process is essential and important before the industrialized production stage. For example, noise and dust should be evaluated during the glass cutting process. This study could contribute significantly to understanding the recycling methods of NMFs from WEEE and serve as guidance for the future technology research and development.     

Bio-drying and size sorting of municipal solid waste with high water content for improving energy recovery

Bio-drying can enhance the sortability and heating value of municipal solid waste (MSW), consequently improving energy recovery. Bio-drying followed by size sorting was adopted for MSW with high water content to improve its combustibility and reduce potential environmental pollution during the follow-up incineration. The effects of bio-drying and waste particle size on heating values, acid gas and heavy metal emission potential were investigated. The results show that, the water content of MSW decreased from 73.0% to 48.3% after bio-drying, whereas its lower heating value (LHV) increased by 157%. The heavy metal concentrations increased by around 60% due to the loss of dry materials mainly resulting from biodegradation of food residues. The bio-dried waste fractions with particle size higher than 45 mm were mainly composed of plastics and papers, and were preferable for the production of refuse derived fuel (RDF) in view of higher LHV as well as lower heavy metal concentration and emission. However, due to the higher chlorine content and HCl emission potential, attention should be paid to acid gas and dioxin pollution control. Although LHVs of the waste fractions with size <45 mm increased by around 2× after bio-drying, they were still below the quality standards for RDF and much higher heavy metal pollution potential was observed. Different incineration strategies could be adopted for different particle size fractions of MSW, regarding to their combustibility and pollution property.