Modelling of Flow and Pollution Dispersion in a Two Dimensional Urban Street Canyon

The wind-driven flow patterns and the dispersion of vehicle exhaust pollutants released at street level has been simulated with the three-dimensional (3-D) dispersion model ADREA-HF (Andronopoulos et al., 1993), for idealised two-dimensional urban fetches occupied by buildings with slanted roofs. The simulation used oncoming atmospheric boundary layer characteristics corresponding to realistic above-town wind characteristics, as measured in reference wind tunnel experiments (Rafailidis, 1997). At that stage, analysis was limited to neutral stability conditions only. Firstly, the quality assurance of the numerical model was investigated in terms of the sensitivity to different grid allocations. The modelling results were corroborated by comparison with wind tunnel measurements in a similar two-dimensional domain (Pavageau et al., 1997). The numerical modelling replicated well the high degree of non-uniformity in the dispersion field in the test street, and the results agreed satisfactorily with the experimental measurements. The reasons for the differences observed have been investigated. With the model thus validated, three different exhaust release scenarios have been tested, keeping the same overall emission rate but different spatial patterns of street-release. The effect of the different street-release scenarios was found to be only marginal, with the dispersion patterns on the sidewalls affected only locally, close to the street level.     

Norwegian Testing of Emulsion Properties at Sea--The Importance of Oil Type and Release Conditions

This paper is a review of the major findings from laboratory studies and field trials conducted in Norway in recent years on the emulsification of oils spilled at sea. Controlled bench-scale and meso-scale basin experiments using a wide spectrum of oils have revealed that both the physico-chemical properties of the oils and the release conditions are fundamental determinants of the rate of emulsion formation, for the rheological properties of the emulsion formed and for the rate of natural dispersion at sea.During the last decade, several series of full-scale field trials with experimental releases of various crude oils have been undertaken in the North Sea and the Norwegian Sea. These have involved both sea surface releases, underwater pipeline leak simulations (release of oil under low pressure and no gas) and underwater blowout simulations (pressurized oil with gas) from 100 and 850 m depth. The field trials have been performed in co-operation with NOFO (Norwegian Clean Seas Association for Operating Companies), individual oil companies, the Norwegian Pollution Control Authority (SFT) and Minerals Management Services (MMS). SINTEF has been responsible for the scientific design and monitoring during these field experiments. The main objectives of the trials have been to study the behaviour of different crude oils spilled under various conditions and to identify the operational and logistical factors associated with different countermeasure techniques.The paper gives examples of data obtained on the emulsification of spilled oil during these field experiments. The empirical data generated from the experimental field trials have been invaluable for the validation and development of numerical models at SINTEF for predicting the spreading, weathering and behaviour of oil released under various conditions. These models are extensively used in contingency planning and contingency analysis of spill scenarios and as operational tools during spill situations and combat operations.     

规划岸线影响下的电厂冷却水数值模拟

随着深圳南山区规划岸线的实施,将影响该海区潮流流态,给前湾燃机电厂的循环冷却水工程造成影响.针对这种情况,利用数值模拟对现状海域流场进行了验证计算,对规划岸线下的流场变化情况及电厂温排水的水力热力特性进行了模拟.在考虑取水温度、经济性、环保性的基础上,为环境评价提供了科学依据.     

The role of wind and emulsification in modelling oil spill and surface drifter trajectories

Laboratory and field data suggest that the movement of spilled oil at sea is in general a three-dimensional phenomenon in physical space, whereas trajectories of undrogued surface drifters are more susceptible to two-dimensional analysis. These conclusions are consistent with the intermittent failure of two-dimensional surface models to simulate the trajectories of spilled oil, although such models may be more successful with data from surface drifters. A physical explanation is presented, and a model that incorporates the key portions of the governing processes is described and tested against data from experimental oil spills at sea. Observations suggest that emulsified surface oil will drift down wind at speeds in excess of 3% of the windspeed. When surface turbulence drives oil subsurface for a significant fraction of time, however, net transport speeds are considerably less and significantly to the right of the wind in the northern hemisphere.     

Treatment of electronic waste to recover metal values using thermal plasma coupled with acid leaching--a response surface modeling approach

The global crisis of the hazardous electronic waste (E-waste) is on the rise due to increasing usage and disposal of electronic devices. A process was developed to treat E-waste in an environmentally benign process. The process consisted of thermal plasma treatment followed by recovery of metal values through mineral acid leaching. In the thermal process, the E-waste was melted to recover the metal values as a metallic mixture. The metallic mixture was subjected to acid leaching in presence of depolarizer. The leached liquor mainly contained copper as the other elements like Al and Fe were mostly in alloy form as per the XRD and phase diagram studies. Response surface model was used to optimize the conditions for leaching. More than 90% leaching efficiency at room temperature was observed for Cu, Ni and Co with HCl as the solvent, whereas Fe and Al showed less than 40% efficiency.     

Modeling of Combined Aerosol and Photooxidant Processes in the Mediterranean Area

The combined UAM-AERO/RAMS modeling system has been applied to study the dynamics of photochemical gaseous species and particulate matter processes in the eastern Mediterranean area between the Greek mainland and the island of Crete. In particular, the modeling system is applied to simulate atmospheric conditions for two periods, i.e., 13-16 July 2000 and 26-30 July 2000. The spatial and temporal distributions of both gaseous and particulate matter pollutants have been extensively studied together with the identification of major emission sources in the area. New pre-processors were developed for the UAM-AERO model for evaluating detailed emission inventories for biogenic compounds, resuspended dust and sea salt. Comparison of the modeling results with measured data was performed and satisfactory agreement was found for a number of gaseous species. However, the model underestimates the PM₁₀ measured concentrations during summer. This is mainly due to the considerable underestimation of particulate matter emissions and in particular dust resuspension, the effect of forest fire emissions and the contribution of Saharan dust episodes.     

Resolving complexities in healthcare waste management: a goal programming approach.

The wide variety of activities at healthcare facilities generates different types of waste. There is always a danger of spreading infection due to mishandling of infectious waste or sharps. Hence, a variety of policies and actions have been taken to improve healthcare waste management systems. A large body of literature is available which suggests methods for tackling different problematic situations but management is confronted with a variety of complex problems, such as the choice of technological options to control infection, legal and budget restrictions and the timely removal of waste, which can, at times, conflict with each other. Hence, a planning model is presented that is based on a trans-shipment goal programming approach wherein the waste flow is optimized for multiple objectives under different priority structures or with different relative importance (weights). The use of the model is demonstrated as a decision-making tool that would help the management to understand the effects of their policies on the system performance. The model is validated for a case application representing a real-life situation. It can be easily seen that, in the case in which the management is biased toward a higher level of safety protection towards infection control, they have to compromise on cost control and to some extent on environmental pollution control.     

Estimation of mass transport parameters of gases for quantifying CH4 oxidation in landfill soil covers

Methane (CH(4)), which is one of the most abundant anthropogenic greenhouse gases, is produced from landfills. CH(4) is biologically oxidized to carbon dioxide, which has a lower global warming potential than methane, when it passes through a cover soil. In order to quantify the amount of CH(4) oxidized in a landfill cover soil, a soil column test, a diffusion cell test, and a mathematical model analysis were carried out. In the column test, maximum oxidation rates of CH(4) (V(max)) showed higher values in the upper part of the column than those in the lower part caused by the penetration of O(2) from the top. The organic matter content in the upper area was also higher due to the active microbial growth. The dispersion analysis results for O(2) and CH(4) in the column are counter-intuitive. As the upward flow rate of the landfill gas increased, the dispersion coefficient of CH(4) slightly increased, possibly due to the effect of mechanical dispersion. On the other hand, as the upward flow rate of the landfill gas increased, the dispersion coefficient of O(2) decreased. It is possible that the diffusion of gases in porous media is influenced by the counter-directional flow rate. Further analysis of other gases in the column, N(2) and CO(2), may be required to support this hypothesis, but in this paper we propose the possibility that the simulations using the diffusion coefficient of O(2) under the natural condition may overestimate the penetration of O(2) into the soil cover layer and consequently overestimate the oxidation of CH(4).     

Field Performance of Point Velocity Probes at a Tidally Influenced Site

Conventional methods to estimate groundwater velocity that rely on Darcy's Law and average hydrogeologic parameter values are insensitive to local‐scale heterogeneities and anisotropy that control advective flow velocity and direction. Furthermore, at sites that are tidally influenced or have extraction wells with variable pumping schedules, infrequent water‐level measurements may not adequately characterize the range and significance of transient hydraulic conditions. The point velocity probe (PVP) is a recently developed instrument capable of directly measuring local‐scale groundwater flow velocity and direction. In particular, PVPs may offer distinct advantages for sites with complex groundwater–surface water interactions and/or with spatially and temporally variable groundwater flow conditions. The PVP utilizes a small volume of saline tracer and inexpensive sensors to directly measure groundwater flow direction and velocity in situ at the centimeter‐scale and discrete times. The probes are installed in conventional direct‐push borings, rather than in wells, thus minimizing the changes and biases in the local flow field caused by well installation and construction. Six PVPs were installed at a tidally influenced site in North Carolina to evaluate their implementability, performance, and potential value as a new site characterization tool. For this study, a new PVP prototype was developed using a rapid prototyping machine (i.e., a “three‐dimensional printer'') and included both horizontally and vertically oriented tracer detectors. A site‐specific testing protocol was developed to account for the spatially and temporally variable hydraulic conditions and groundwater salinity. The PVPs were tested multiple times, and the results were compared to the results of several different groundwater flux and velocity estimation tools and methods, including a heat‐pulse flowmeter, passive flux meters, single‐well tracer tests, and high‐resolution hydraulic gradient analysis. Overall, the results confirmed that the PVP concept is valid and demonstrated that reliable estimates of groundwater velocity and direction can be obtained in simple settings. Also, PVPs can be successfully installed by conventional methods at sites where the formation consists primarily of noncohesive soils and the water table is relatively shallow. Although some PVP tests yielded consistent and reliable results, several tests did not. This is likely due to the highly transient flow conditions and limitations associated with the PVP design and testing procedures. PVPs offer particular advantages over, and can effectively complement, other groundwater flow characterization techniques for certain conditions, and objectives may be useful for characterizing complex flow patterns under steady conditions; however, this study suggests that PVPs are best suited for conditions where the flow hydraulics are not highly transient. For sites where the hydraulic conditions are highly transient, the most reliable approach for understanding groundwater flow behavior and groundwater–surface water interactions would generally involve both a high‐resolution hydraulic gradient analysis and another local‐scale method, such as tracer testing. This study also highlighted some aspects of the current PVP design and testing protocol that can be improved upon, including a more robust connection between the PVP and injection line and further assessment of tracer solution density effects on vertical flow. © 2013 Wiley Periodicals, Inc.     

应曲面法优化H2O2催化氧化烟气脱硝工艺

研究了H₂O₂催化氧化烟气脱硝工艺中H₂O₂质量分数、催化剂浓度和溶液pH对脱硝率的影响,采用 Box-Behnken响应曲面法优化了H₂O₂脱硝的工艺条件,得到了相应的数学模型,并进行了方差分析。结果表明,溶液pH、催化剂浓度、H₂O₂质量分数以及催化剂浓度和H₂O₂质量分数的一级交互作用对脱硝率的影响很显著,模型的决定系数为0.995 3,说明模型拟合效果很好。经模型优化分析的最优工艺条件为H₂O₂质量分数0.2%,催化剂浓度0.94 mmol/L,溶液pH 11.0,在此条件下处理进口流量3.5 L/min、 NO体积分数 2×10^-4、O₂体积分数10%、N₂体积分数90%的烟气,液气比为8 L/m³,脱硝率达97%。     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

Studies on enhanced degradable plastics. II. Weathering of enhanced photodegradable polyethylenes under marine and freshwater floating exposure

The weatherability of three types of enhanced photodegradable polyethylene films and corresponding control films were studied under outdoor and marine floating conditions at two exposure sites. Progress of weathering was monitored using tensile elongation at break. In general, both the enhanced-degradable plastics and the corresponding controls degraded slower in marine exposure than in outdoor exposure. This is attributed to the lower sample temperatures (compared to samples exposed outdoors) and to shielding from light afforded by surface fouling in samples exposed floating in sea water. Enhanced-photodegradable polyethylenes disintegrated faster than the control samples in the case of both outdoor and marine exposures. The improvement obtained in marine exposures was greater than that for outdoor exposure of corresponding sample types. This is due to the extremely slow rates of disintegration of control films under marine floating conditions.     

Scenario assessment of neodymium recycling in Japan based on substance flow analysis and future demand forecast

With the increasing demand for energy-saving technologies, neodymium-iron-boron magnets have been widely utilized in high-efficiency motors. However, the reserves of neodymium, which is a rare earth element (REE), are limited; thus, a strategy for scaling up the REE supply is highly required. In this study, a scenario assessment was conducted to evaluate the effect of material recycling of neodymium from final product waste. Domestic substance flow analysis of neodymium was conducted by focusing on the waste flow of the final product. Moreover, the demand and waste of neodymium until 2050 were forecasted using various multivariate analysis methods. The results showed that the domestic waste of neodymium was forecasted to be 3866–4217 tons/year by 2050. However, material recycling of neodymium from final product waste may cause an additional increase in production by “circular economy rebound”. Considering that CO₂ reduction has also been a global challenge to prevent global warming, the rebound effect was calculated. Therefore, a scenario assessment was conducted to evaluate the influence of this rebound effect by estimating the CO₂ reduction. The results of this study are expected to make a significant contribution to the establishment of a new strategy for neodymium recycling.

     

Sequestration of metals in active cap materials: A laboratory and numerical evaluation

Active capping involves the use of capping materials that react with sediment contaminants to reduce their toxicity or bioavailability. Although several amendments have been proposed for use in active capping systems, little is known about their long‐term ability to sequester metals. Recent research has shown that the active amendment apatite has potential application for metals‐contaminated sediments. The focus of this study was to evaluate the effectiveness of apatite in the sequestration of metal contaminants through the use of short‐term laboratory column studies in conjunction with predictive, numerical modeling. A breakthrough column study was conducted using North Carolina apatite as the active amendment. Under saturated conditions, a spike solution containing elemental As, Cd, Co, Se, Pb, Zn, and a nonreactive tracer was injected into the column. A sand column was tested under similar conditions as a control. Effluent water samples were periodically collected from each column for chemical analysis. Relative to the nonreactive tracer, the breakthrough of each metal was substantially delayed by the apatite. Furthermore, breakthrough of each metal was substantially delayed by the apatite compared to the sand column. Finally, a simple 1‐D, numerical model was created to qualitatively predict the long‐term performance of apatite based on the findings from the column study. The results of the modeling showed that apatite could delay the breakthrough of some metals for hundreds of years under typical groundwater flow velocities. © 2012 Wiley Periodicals, Inc.     

A Study of Sustainable Material Management Approach in Taiwan

Sustainable material management (SMM) has been initiated by the Organization for Economic Cooperation and Development (OECD) in 2005. SMM is an approach to promote resource conservation, reducing negative environmental impacts and preserving the natural capital of material and the balance of economic efficiency and social equity. Life cycle assessment and material flow analysis have been widely used to estimate the environmental impacts for resource consumption, but economic development has not been taken into account. Before 1984, improper garbage disposal was not an important issue in Taiwan. But over the past three decades, the Taiwan Government has accomplished not only waste disposal but also resource recycling, which are conducive to the essence of SMM. This study is the first research project to develop a SMM conceptual model for policy and strategy in Taiwan. SMM is the suitable waste management concept for the next era. This study reviewed the policy and strategy that has been applied in Taiwan’s waste management, and compares the efficiency of waste management policy in Taiwan with the concept of SMM. A case study of the waste flow will be used to prove that the sustainable material policy can be a suitable management system to achieve sustainable development. This study will open a new chapter of research on global SMM for Taiwan.     

Air and landfill gas movement through passive gas vents installed in closed landfills

In a closed landfill, Japan, remedial actions have been undertaken to address the inadequate leachate collection and drainage systems. Part of this process included installing many passive gas vents in the landfill to promote stabilization of landfilled waste. This study focused on the gas velocity in vents by conducting tracer tests to elucidate the gas flow via passive gas vents. The gas composition and gas temperature in the vents was also measured.As the gas vents pass through the waste layer, both landfill gas and air flows through the vents. Therefore, passive gas vents can be used to aerate landfilled waste as well as to collect and release landfill gas. Aerobic biodegradation occurs when air migrates through the waste layer if organic matter is present; this increases the temperature of the waste layer. Inflow of air into the gas vents can occur at a wide range of depths, even 10–20 m below ground level. Air is induced not from the surface of the landfill, but horizontally along the waste layer. The driving force of air induction from outside is a buoyancy effect caused by the temperature rise due to aerobic biodegradation.     

An attempt to perform water balance in a Brazilian municipal solid waste landfill

This paper presents an attempt to model the water balance in the metropolitan center landfill (MCL) in Salvador, Brazil. Aspects such as the municipal solid waste (MSW) initial water content, mass loss due to decomposition, MSW liquid expelling due to compression and those related to weather conditions, such as the amount of rainfall and evaporation are considered. Superficial flow and infiltration were modeled considering the waste and the hydraulic characteristics (permeability and soil-water retention curves) of the cover layer and simplified uni-dimensional empirical models. In order to validate the modeling procedure, data from one cell at the landfill were used. Monthly waste entry, volume of collected leachate and leachate level inside the cell were monitored. Water balance equations and the compressibility of the MSW were used to calculate the amount of leachate stored in the cell and the corresponding leachate level. Measured and calculated values of the leachate level inside the cell were similar and the model was able to capture the main trends of the water balance behavior during the cell operational period.     

Inexact fuzzy-stochastic constraint-softened programming – A case study for waste management

In this study, an inexact fuzzy-stochastic constraint-softened programming method is developed for municipal solid waste (MSW) management under uncertainty. The developed method can deal with multiple uncertainties presented in terms of fuzzy sets, interval values and random variables. Moreover, a number of violation levels for the system constraints are allowed. This is realized through introduction of violation variables to soften system constraints, such that the model’s decision space can be expanded under demanding conditions. This can help generate a range of decision alternatives under various conditions, allowing in-depth analyses of tradeoffs among economic objective, satisfaction degree, and constraint-violation risk. The developed method is applied to a case study of planning a MSW management system. The uncertain and dynamic information can be incorporated within a multi-layer scenario tree; revised decisions are permitted in each time period based on the realized values of uncertain events. Solutions associated with different satisfaction degree levels have been generated, corresponding to different constraint-violation risks. They are useful for supporting decisions of waste flow allocation and system-capacity expansion within a multistage context.     

Valorisation of waste tyre by pyrolysis in a moving bed reactor

The aim of this work is to assess the behaviour of a moving bed reactor, based on a screw transporter design, in waste tyre pyrolysis under several experimental conditions. Waste tyre represents a significant problem in developed countries and it is necessary to develop new technology that could easily process big amounts of this potentially raw material. In this work, the influence of the main pyrolysis process variables (temperature, solid residence time, mass flow rate and inert gas flow) has been studied by a thorough analysis of product yields and properties. It has been found that regardless the process operational parameters, a total waste tyre devolatilisation is achieved, producing a pyrolytic carbon black with a volatile matter content under 5 wt.%. In addition, it has been proven that, in the range studied, the most influencing process variables are temperature and solid mass flow rate, mainly because both variables modify the gas residence time inside the reactor. In addition, it has been found that the modification of these variables affects to the chemical properties of the products. This fact is mainly associated to the different cracking reaction of the primary pyrolysis products.     

DeepBlow – a Lagrangian Plume Model for Deep Water Blowouts

This paper presents a sub-sea blowout model designed with special emphasis on deep-water conditions. The model is an integral plume model based on a Lagrangian concept. This concept is applied to multiphase discharges in the formation of water, oil and gas in a stratified water column with variable currents. The gas may be converted to hydrate in combination with seawater, dissolved into the plume water, or leaking out of the plume due to the slip between rising gas bubbles and the plume trajectory. Non-ideal behaviour of the gas is accounted for by the introduction of pressure- and temperature-dependent compressibility z-factor in the equation of state. A number of case studies are presented in the paper. One of the cases (blowout from 100 m depth) is compared with observations from a field experiment conducted in Norwegian waters in June 1996. The model results are found to compare favourably with the field observations when dissolution of gas into seawater is accounted in the model. For discharges at intermediate to shallow depths (100–250 m), the two major processes limiting plume rise will be: (a) dissolution of gas into ambient water, or (b) bubbles rising out of the inclined plume. These processes tend to be self-enforcing, i.e., when a gas is lost by either of these processes, plume rise tends to slow down and more time will be available for dissolution. For discharges in deep waters (700–1500 m depth), hydrate formation is found to be a dominating process in limiting plume rise.