Sustainable Waste Management of Engineering Plastics Generated from E-Waste: A Critical Evaluation of Mechanical,Thermal and Morphological Properties

Journal of Polymers and the Environment - The major roadblock for recycling of waste electrical and electronic equipments (WEEE) depends on the viability of sorting process, which is a complex...     

Green and Sustainable Shoreline Restoration of a Coastal Superfund Landfill

Following costly repairs of a coastal landfill's shoreline protection system (SPS) within a tidal zone with additional future repairs imminent, a green and sustainable remedy optimization to eliminate the root cause of the damage was evaluated. The removal of the armored point located just north of the landfill that had been a major source of erosion to the SPS during storm events was proposed and implemented. The restoration of the beach to protect the landfill and restore natural longshore processes, while providing habitat for wildlife, was a key goal of the project. As a part of the work, the removal of a creosote‐impregnated boat ramp was incorporated into the final design at the request of stakeholders. During the process, all materials excavated from the site were either beneficially reused in the construction or reused off‐site as concrete, clean fill, or fuel. The work was implemented in the dry by working with the tides and successfully achieved the project goals. Based on the initial inspections following the repairs, no additional repairs are anticipated well into the future. © 2016 Wiley Periodicals, Inc.     

Diurnal Profile of Particle-bound Polycyclic Aromatic Hydrocarbon (pPAH) Concentration in Urban Environment in Tokyo Metropolitan Area

Traffic emits particles under 1 m. The particles arethe most responsible to particle-bound polycyclic aromatichydrocarbon (pPAH) which can impact human health. To assessthem as health hazards, we monitored diurnal changes in theconcentration and distribution of pPAH near roads in Tokyo.The total pPAH concentration was determined using aphotoelectric aerosol sensor (PAS) which ionized PAH-adsorbingparticles. The total pPAH concentration was compared withchemical analyses by gas chromatography/mass spectrometry(GC/MS). Two sampling sessions, one in August and one inSeptember 2000, were done at three sampling sites at the Hongo Campus of the University of Tokyo. Monitoring was every two minutes for six consecutive days for the first session and for seven consecutive days for the second session.Correlation of the pPAH concentration with traffic flow andwith meteorological conditions were also assessed. The pPAHconcentration varied in the same manner on all days: it sharplyincreased in the early morning by a sudden burden of traffic, and it rapidly decreased during the daytime, probably owing tophotodegradation and/or dilution by rising in the mixingzone. The local wind field, and consequently thetransportation of pPAH from the road, were stronglyinfluenced by the configuration and location of thesurrounding buildings. The pPAH clearly changed in 1- and0.5 day cycles, particularly at the roadside.     

ICAROS: An Integrated Computational Environment for the Assimilation of Environmental Data and Models for Urban and Regional Air Quality

Integrated environmental management in urban areas is nowadaysconsidered a sine qua non objective of Community and nationalenvironmental and development policies. A large amount ofscientific information on the state of the environment is nowavailable from a large pool of data sources. This work presentsan innovative method for integration of these data sources andeffective coupling of environmental information with appropriatemodels and decision-support tools. State-of-the-art Earthobservation techniques, ground-based air quality measurements,atmospheric transport and chemical modelling, and multi-criteriadecision-aid systems are used in an integrated information fusionenvironment in support of environmental and health impactassessment and decision-making at the urban and regional scales. Results of the pilot application of the method in the area ofLombardy in Northern Italy demonstrate the validity andusefulness of this novel approach.     

Remediation of a Diffuse Trichloroethene Plume in an Urban Setting

During an environmental assessment of a former fleet vehicle maintenance facility located in Jacksonville, Florida, dissolved trichloroethene (TCE) concentrations exceeding the Florida groundwater standard (3 micrograms per liter) were detected at a depth of 40 feet (12 meters) below land surface (bls). A plume was delineated that measured approximately 600 feet (183 meters) by 150 feet (46 meters), extending across a major road and onto adjacent properties. Shaw Environmental, Inc., which was acquired by CB&I in February 2012, performed pilot tests with in situ oxygen curtain (iSOC), and the injection of Anaerobic Biochem Plus (ABC+), a mixture of lactates, a phosphate buffer, fatty acids, and zero‐valent iron. Based on the pilot‐test results, ABC+ appeared the more effective of the two methods and was selected for full‐scale implementation. In February 2011, Shaw Environmental, Inc. and a subcontractor used direct‐push technology to inject ABC+ in 120 borings. By September 2011, the treatment succeeded in lowering the concentrations of TCE to below the Florida standard in all impacted wells. Subsequent sampling events indicate that TCE concentrations have remained below the standard, but sampling continues for iron, which is decreasing but remains slightly elevated. © 2013 Wiley Periodicals, Inc.     

Biodegradation of Epoxy and MF Modified Polyurethane Films Derived from a Sustainable Resource

Mesua ferrea L. seed oil (MFLSO) modified polyurethanes blends with epoxy and melamine formaldehyde (MF) resins have been studied for biodegradation with two techniques, namely microbial degradation (broth culture technique) and natural soil burial degradation. In the former technique, rate of increase in bacterial growth in polymer matrix was monitored for 12 days via a visible spectrophotometer at the wavelength of 600 nm using McFarland turbidity as the standard. The soil burial method was performed using three different soils under ambient conditions over a period of 6 months to correlate with natural degradation. Microorganism attack after the soil burial biodegradation of 180 days was realized by the measurement of loss of weight and mechanical properties. Biodegradation of the films was also evidenced by SEM, TGA and FTIR spectroscopic studies. The loss in intensity of the bands at ca. 1735 cm⁻¹ and ca. 1050 cm⁻¹ for ester linkages indicates biodegradation of the blends through degradation of ester group. Both microbial and soil burial studies showed polyurethane/epoxy blends to be more biodegradable than polyurethane/MF blends. Further almost one step degradation in TG analysis suggests degradation for both the blends to occur by breakage of ester links. The biodegradation of the blends were further confirmed by SEM analyses. The study reveals that the modified MFLSO based polyurethane blends deserve the potential to be applicable as “green binders” for polymer composite and surface coating applications.     

Development of Ambient Cured Polyesteramide Coatings from Linseed Oil: a Sustainable Resource

The resourceful employment of vegetable oil based polymers in coating applications that yield novel properties, faces challenges usually in their processing. We have developed polyesteramide coatings from linseed (Linnum ussitatissium seeds) oil with improved coating properties. Linseed oil was first converted into N, N-bis 2-hydroxy ethyl linseed oil fatty amide diol (HELA). The resin was synthesized by the reaction of HELA with ethylenediaminetetraacetic acid (EDTA) to develop ethylenediamine polyesteramide (Ed-PEA). The latter was further treated with poly (styrene co-maleic anhydride) (SMA) in different (35–50) phr (part per hundred part of resin) to obtain ambient cured polyesteramide (AC-PEA). The structural elucidation of polymeric resin (AC-PEA) was carried out by FT-IR, ¹H-NMR, and ¹³C-NMR spectroscopic techniques. Thermal behavior of AC-PEA was studied by thermogravimetric analyses (TGA) and differential scanning calorimetry (DSC). The coatings of AC-PEA were prepared on mild steel strips to investigate their physico-mechanical and anticorrosive behavior (in acid, alkali, water and xylene). It was found that among all the samples, the one having 45 phr of SMA showed the best physico-mechanical and corrosion resistance performance. The thermal stability performance suggests that AC-PEA45 system could be safely used up to 150 °C.     

Biodegradation of Coproducts from Industrially Processed Corn in a Compost Environment

Information pertaining to biodegradability of renewable polymeric material is critical for the design and development of single-use biodegradable consumer products. The rate and extent of biodegradation of corn fiber, corn zein, cornstarch, distillers grain, and corn gluten meal were evaluated in compost environments under variable temperature, pH, and moisture conditions. Generally, composts with higher temperature (40°C), neutral pH (7.0), and 50%–60% moisture appeared to be ideal for corn coproduct biodegradation, particularly for corn gluten meal and corn zein. Low moisture conditions slowed biodegradation considerably, but degradation rates improved when moisture content increased up to 60%. Thereafter, increased moisture particularly slowed the degradation of corn gluten meal and corn zein, whereas cornstarch degradation remained unaffected. At low pH (4.0) and high pH (11.0) the rate of degradation of most coproducts was slowed somewhat. Cornstarch degradation was slower at pH 7.0, but degradation improved with increased temperatures. Increase in compost temperature from 25 to 40°C (in 5°C increments) also improved biodegradation of corn fiber and distillers grain. Addition of 1% urea to compost as a nitrogen source decreased the extent of biodegradation nearly 40% for corn gluten meal and corn zein, and 20% for cornstarch samples. Treatment of compost with 0.02% azide inhibited biodegradation of all coproducts, suggesting that the presence of metabolically active microbial cells is required for effective degradation of biobased materials in a compost environment.     

Sustainable wind‐driven bioventing at a petroleum hydrocarbon–impacted site

Bioventing—the injection of air into the vadose zone to increase microbial activity—is a commonly used, proven technology for remediating volatile organic compounds present in the vadose zone. Passive systems driven by wind or solar power are both more cost‐effective and sustainable than conventional systems. Such a passive system is being applied successfully to remediate a site impacted with total petroleum hydrocarbons (TPH) and benzene, toluene, ethylbenzene, and xylenes (BTEX) in soil. Bioventing technology was approved by the regulatory agency as an interim remedial action to remove chemicals of concern (COCs) in the vadose zone. A bioventing pilot study was conducted to evaluate the effectiveness of COC removal and collect parameters for full‐scale design and implementation. To evaluate the potential to use wind‐driven bioventing technology, two mobile weather stations were installed at the site and monitored for one month for a wind speed study. Based on the pilot‐test data and wind speed research, 12‐inch diameter funnel/vane 360‐degree wind collectors were designed as passive wind‐driven air‐injection devices and connected to existing monitoring wells. The measured air velocity ranged from 20 to 110 feet per minute during the start‐up and the first three months of operation and maintenance. Monitoring indicated a 20 percent oxygen delivery and greater than 90 percent reduction in COC concentrations, demonstrating a successful sustainable remediation with no power requirement and minimal operation and maintenance. © 2012 Wiley Periodicals, Inc.     

There Are More Than Three Reasons to Consider Sustainable Remediation,a Dutch Perspective

This article provides an overview of the developments concerning sustainable remediation (SR) from the authors’ perspective. A short history of policy development is outlined, in which the focus mainly lies on the Netherlands since this is the homeland of the majority of the authors. The Netherlands is a densely populated country with high pressure on land and was in the forefront of developments in soil policy. The authors plead for simplicity in approaches, as history has proven that the simpler theory more often is true, and above all will better be understood by stakeholders and, thus, will more easily lead to consensus. Implicitly the authors make clear that SR not only has benefits from a societal, economic, and environmental point of view, but if the methodologies are implemented correctly, it leads to more robust and supported decision making. Moreover, it opens the road to flexible and integral remedial objectives that enable innovative and creative solutions for soil and groundwater contamination. The proposed methodologies and creative innovations are illustrated with full‐scale operational cases. ©2017 Wiley Periodicals, Inc.     

Application of a Proposed Generic LLW Waste Package Analysis With Changing Infiltration in a Humid Environment

Corrosion of carbon steel boxes filled with low‐level radioactive waste and buried within a near surface disposal facility in a humid environment was evaluated using an integrated systems approach framework. The time to hydraulic failure from initial burial to development of holes through the wall of a given waste package from pitting corrosion was calculated for four corrosion scenarios under two different corrosion cases. The two corrosion cases chosen were a constant rate of corrosion and a slowing rate of corrosion. Corrosion rates were estimated for carbon steel buried in soil from several historical studies and related to the corrosivity and aeration profile of the soil. The scenarios were chosen to represent a range of possible conditions at current and future U.S. Department of Energy disposal facilities. For each scenario, once the time to hydraulic failure had been estimated, the amount of liquid present in each waste package at the time of failure was calculated as an estimate of leachate available for subsurface transport. The Savannah River E‐Area Engineered Trench was used as a basis for the hypothetical disposal facility. © 2016 Wiley Periodicals, Inc.     

Modelling of Flow and Pollution Dispersion in a Two Dimensional Urban Street Canyon

The wind-driven flow patterns and the dispersion of vehicle exhaust pollutants released at street level has been simulated with the three-dimensional (3-D) dispersion model ADREA-HF (Andronopoulos et al., 1993), for idealised two-dimensional urban fetches occupied by buildings with slanted roofs. The simulation used oncoming atmospheric boundary layer characteristics corresponding to realistic above-town wind characteristics, as measured in reference wind tunnel experiments (Rafailidis, 1997). At that stage, analysis was limited to neutral stability conditions only. Firstly, the quality assurance of the numerical model was investigated in terms of the sensitivity to different grid allocations. The modelling results were corroborated by comparison with wind tunnel measurements in a similar two-dimensional domain (Pavageau et al., 1997). The numerical modelling replicated well the high degree of non-uniformity in the dispersion field in the test street, and the results agreed satisfactorily with the experimental measurements. The reasons for the differences observed have been investigated. With the model thus validated, three different exhaust release scenarios have been tested, keeping the same overall emission rate but different spatial patterns of street-release. The effect of the different street-release scenarios was found to be only marginal, with the dispersion patterns on the sidewalls affected only locally, close to the street level.     

Sustainable remediation panel—Measuring the social and economic benefits of a sustainable remediation project

Remediation developed a Sustainable Remediation Panel in the Summer 2009 issue, which featured the Sustainable Remediation Forum White Paper. The panel is composed of leaders in the field of sustainable remediation who have volunteered to provide their opinions on difficult subjects related to the topic of how to integrate sustainability principles into the remediation practice. The panel's opinions are provided in a question‐and‐answer format, whereby selected experts provide an answer to a question. This issue's question is provided below, followed by opinions from five experts in the remediation field.

相似文献   

Comparative Investigations on Optimum Polymerization Conditions for the Synthesis of a Sustainable Poly(Lactic Acid)

The development of synthetic biodegradable polymers using solvent free polymerization has a unique potential to be used as sustainable polymers in biomedical applications. The aim of this work was to synthesize and characterize a sustainable class of poly(lactic acid) (PLA) under different operating conditions via direct polycondensation of lactic acid (LA). Several parameters were tested including the absence of solvents and catalysts on the polymerization, in addition to polymerization temperature and time. Polymerization conditions were evaluated using response surface method (RSM) to optimize the impact of temperature, time, and catalyst. Results showed that molecular weight (M_w) of PLA increased with increasing polymerization time. Highest M_w of 28.4 kD with relatively a broad polydispersity 1.9 was achieved at polymerization temperature 170?°C at 24 h in the free solvent polymerization. This led to a relevant inherent viscosity of 0.37 dl/g. FTIR spectra exhibited a disappearance of the characteristic peak of the hydroxyl group in LA at 3482 cm^?1 by increasing the intensity of carbonyl group. The ¹H nuclear magnetic resonance (NMR) exhibited the main chain at 5.22 ppm and the signal of methyl proton at 1.61 ppm as well as a signal at 4.33 and 1.5 assigned to the methane proton next to the terminal hydroxyl group and carboxyl group respectively. Meanwhile, the PLA synthesized with a catalyst [Sn(Oct)₂] in a free solvent demonstrated comparatively high thermal transition properties of glass transition, melting, and crystallinity temperatures of 48, 106, and 158?°C, respectively. These results are of significant interest to further expand the use of PLA in biomedical applications.     

Sustainable recycling of municipal solid waste in developing countries

This research focuses on recycling in developing countries as one form of sustainable municipal solid waste management (MSWM). Twenty-three case studies provided municipal solid waste (MSW) generation and recovery rates and composition for compilation and assessment. The average MSW generation rate was 0.77 kg/person/day, with recovery rates from 5-40%. The waste streams of 19 of these case studies consisted of 0-70% recyclables and 17-80% organics. Qualitative analysis of all 23 case studies identified barriers or incentives to recycling, which resulted in the development of factors influencing recycling of MSW in developing countries. The factors are government policy, government finances, waste characterization, waste collection and segregation, household education, household economics, MSWM (municipal solid waste management) administration, MSWM personnel education, MSWM plan, local recycled-material market, technological and human resources, and land availability. Necessary and beneficial relationships drawn among these factors revealed the collaborative nature of sustainable MSWM. The functionality of the factor relationships greatly influenced the success of sustainable MSWM. A correlation existed between stakeholder involvement and the three dimensions of sustainability: environment, society, and economy. The only factors driven by all three dimensions (waste collection and segregation, MSWM plan, and local recycled-material market) were those requiring the greatest collaboration with other factors.     

Sustainable Use of Coffee Husks For Reinforcing Polyethylene Composites

The utilization of the coffee husk fiber (CHF) from the coffee industry as a reinforcing filler in the preparation of a cost-effective thermoplastic based composite was explored in this study. The chemical composition and thermal properties of the CHF were investigated and compared with those of wood fiber (WF). CHF proved to be mainly composed of cellulose, hemicellulose and lignin, and exhibited similar thermal behavior to WF. High density polyethylene (HDPE) composites with CHF loadings of from 40 to 70% were prepared using melt processing and extrusion. The processing properties, mechanical behavior, water absorption and thermal performance of these composites were investigated. The effect of maleated polyethylene (MAPE) used as a coupling agent on the composite was explored. The experimental results showed that increasing the CHF loading in the HDPE matrix resulted in an increase in the modulus and thermal properties of the composites, but resulted in poor water resistance. The addition of a 4% MAPE significantly improved the interfacial behavior of the hydrophilic lignocellulosic fiber and the hydrophobic polymer matrix.