网络版论文摘要

垃圾填埋场渗滤液后处理的研究柴晓利　赵由才(同济大学污染控制与资源化研究国家重点实验室 ,上海 2 0 0 0 92 )采用混凝絮凝法对经生化处理后的垃圾渗滤液进行后处理。结果表明 ,混凝絮凝法对难降解有机质的去除十分有效 ,CODCr去除率可达 6 0 %以上。特别是微生物絮凝剂由于用量少 ,不产生二次污染 ,可应用于垃圾渗滤液特别是给水难降解有机质的去除工艺中。关键词 :絮凝剂 ,垃圾渗滤液 ,混凝絮凝法。粉煤灰混凝剂的制备和预处理印染废水的试验研究李　磊　赵玉明(南京大学环境学院污染控制与资源化研究国家重点实验室 ,南京 2 10 0 93…     

混凝好氧颗粒污泥的絮凝剂选择

为选择出适应于混凝好氧颗粒污泥培养的絮凝剂,通过絮凝剂添加量、污泥浓度、搅拌速度、搅拌时间等因子进行L9(3)4正交实验,以COD、浊度去除效果及絮凝颗粒结构为考察因子,研究聚合氯化铝(PAC)、聚丙烯酰胺(PAM)及壳聚糖的絮凝效果。结果表明,在不同絮凝剂的最佳混凝条件下,PAM的效果最好,壳聚糖次之,PAC最差,但壳聚糖COD随其添加浓度的增加而增加;絮凝颗粒结构中,以PAM的絮凝颗粒效果最好,其结构紧溱而颗粒中间的空隙相对较大,有利于吸附污染物和微生物的生长,适宜作为颗粒污泥培养的絮凝剂。     

新型鼓风炉铁泥基混凝剂的制备及应用研究

研究在鼓风炉铁泥中加入适量的粉煤灰和助溶剂HS,在90℃温度下搅拌浸取2.5h后,制得集物理吸附和化学混凝为一体的混凝剂.这种混凝剂与PSA絮凝剂配合用于制革和纺织印染废水的处理,与传统混凝剂相比,COD和色度的去除率均提高30%左右.其显著特点是混凝沉降速度快,污泥体积小,处理废水费用低,并结合显微照片探讨了混凝剂对废水的混凝沉降机理.     

新型鼓风炉铁泥基混凝剂的制备及应用研究

研究在鼓风炉铁泥中加入适量的粉煤灰和助溶剂HS,在90℃温度下搅拌浸取2．5h后,制得集物理吸附和化学混凝为一体的混凝剂。这种混凝剂与PSA絮凝剂配合用于制革和纺织印染废水的处理,与传统混凝剂相比,COD和色度的去除率均提高30％左右。其显著特点是混凝沉降速度快,污泥体积小,处理废水费用低,并结合显微照片探讨了混凝剂对废水的混凝沉降机理。     

微絮凝-超滤工艺处理微污染水源水的中试研究

进行了微絮凝．超滤工艺处理微污染水源水的中试研究。试验结果表明：在微絮凝-超滤工艺中，相同混凝剂投加量（相同金属摩尔浓度）下铁盐比铝盐的混凝效果好；微絮凝-超滤工艺的最佳絮凝时间为120s左右；最佳混凝剂投加量为2．2mg／L（以Fe计）。微絮凝-超滤工艺在改善出水水质和缓解膜污染方面均优于直接超滤工艺。微絮凝-超滤工艺的出水水质均符合建设部《城市供水水质标准》（CJ／T206-2005）要求。     

汽车电泳磷化废水的特点及处理

汽车工业电泳磷化废水成分复杂、COD值高、可生化性差。聚合氯化铝 (PAC)对乳化油珠的电中和破乳及其凝絮对高分子有机物的吸附起主要作用 ;选择阳离子高分子絮凝剂 ,由于其水解产物带有正电荷铵盐基团 ,加强了残存COD的吸附 ,完善了絮凝分离过程。选用恰当的混凝剂和设计合理的工艺流程 ,采用以混凝为基础的物理化学方法 ,可以进行有效的处理。     

微絮凝-超滤工艺处理微污染水源水的中试研究

进行了微絮凝-超滤工艺处理微污染水源水的中试研究.试验结果表明:在微絮凝-超滤工艺中,相同混凝剂投加量(相同金属摩尔浓度)下铁盐比铝盐的混凝效果好;微絮凝-超滤工艺的最佳絮凝时间为120 s左右;最佳混凝剂投加量为2.2 mg/L(以Fe计).微絮凝-超滤工艺在改善出水水质和缓解膜污染方面均优于直接超滤工艺.微絮凝-超滤工艺的出水水质均符合建设部<城市供水水质标准>(CJ/T206-2005)要求.     

汽车电泳磷化废水的特点及处理

汽车工业电泳磷化废水成分复杂、COD值高、可生化性差。聚合氯化铝(PAC)对乳化油珠的电中和破乳及其凝絮对高分子有机物的吸附起主要作用；选择阳离子高分子絮凝剂，由于其水解产物带有正电荷铵盐基团，加强了残存COD的吸附，完善了絮凝分离过程。选用恰当的混凝剂和设计合理的工艺流程，采用以混凝为基础的物理化学方法，可以进行有效的处理。     

混凝絮凝法去除腐质酸的研究

进行了混凝絮凝法去除水中腐殖酸的研究，结果表明，同传统的絮凝剂相比，微生物絮凝剂不仅用量少，去除效果好(去除率可达60％)，而且不产生二次污染，可应用于废水特别是给水中腐殖酸的去除工艺中，对絮凝剂的絮凝机理进行了初步研究，研究表明，微生物絮凝剂去除腐殖酸主要是通过架桥完成的，不同于A12(SO4)3的电中和机理。     

加药量和水力搅拌速度对雨水混凝效果的影响

为降低分流制雨水中悬浮颗粒物及其他污染物浓度,减轻城市景观河道的水体富营养化程度,对取自泵站的雨水进行混凝沉淀工艺优化实验。以PAC为混凝剂,采用Zeta电位仪、激光粒度仪和iPDA在线监测技术对混凝过程进行监测,考察了混凝剂投加量和水力搅拌速度对絮体形成和分流制雨水处理效果的影响,结果表明,混凝剂投加量和混合水力搅拌速度直接影响絮体Zeta电位和聚沉特性;混合搅拌速度控制混凝反应速率,絮凝速度梯度影响絮体形成粒径。FI曲线特征参数对控制混凝工艺具有指导意义。PAC投加量为35 mg/L,混合阶段搅拌速度800 r/min,搅拌30 s,絮凝阶段采用150、108和60 r/min的转速各自搅拌5 min,沉后水中剩余颗粒总数最少,浊度、COD和总磷去除效果最佳。     

Determining the effectiveness of conventional and alternative coagulants through effective characterization schemes

Polymeric forms of metal coagulants in water treatment have become increasingly used due to their wider availability and reduction in cost. These specialized coagulant forms and products are claimed by manufacturers to be superior to conventional coagulants in particulate and/or organic removal with inherent advantages of lower alkalinity consumption and lesser sludge production. However, due to their proprietary nature, little is known about their chemical composition. To determine and understand the effectiveness of these alternative coagulants, a comprehensive study was undertaken to characterize metal coagulants, and to comparatively evaluate them on a well-characterized source water. The objective of this study was to provide a scheme for utilities that could be employed as a screening process and a method of selecting an appropriate coagulant based on raw water characteristics and insight into the coagulatability of the source water. Characterizations of coagulants included: (i) active metal content, (ii) anion content, (iii) acidity, (iv) alkalinity consumption, (v) charge reversal by colloidal titration, and (vi) molecular weight determination. A total of five poly-aluminum chlorides (PACl), along with a conventional coagulant (aluminum sulfate or alum) were evaluated. Results show that through the characterization scheme, an effective coagulant (conventional versus alternative) and coagulant type (among various PACl) can be chosen before undertaking time-consuming bench or pilot-scale evaluation.     

地表水中隐孢子虫和贾第鞭毛虫微球的混凝去除

以向地表水中投加的隐孢子虫微球和贾第鞭毛虫微球为对象,研究通过对给水混凝工艺对其的去除效果进行比较,着重考察了不同混凝剂种类、投加量及水样pH值对去除效果的影响.结果表明,混凝工艺可较为有效地去除地表水中的两虫微球,去除率最高可达4 lg.相比常规的金属盐类混凝剂,高分子的PAC、PAFC混凝剂对两虫微球的混凝去除率更...     

复配混凝剂理化特性及性能

用聚二甲基二烯丙基氯化铵（PDM）、聚合氯化铝（PAC）按照质量比1%制备了复配混凝剂,研究了其理化特性及原水污染物去除效果。利用Al-Ferron逐时络合比色法研究了复配混凝剂的铝（Ⅲ）形态分布,结果表明,Al_a、Al_b和Al_c分别占12.62%、16.02%和71.36%。复配混凝剂Zeta电位平均值为41.6 mV。红外吸收光谱分析表明复配混凝剂的羟基缔合程度比PAC要高。扫描电镜结果表明,固体复配混凝剂表面较为粗糙、结构疏松。相同投加量时,复配混凝剂对江河水、水库水的浊度、COD_Mn、UV₂₅₄的去除效率均优于PAC。实验利用针杆藻人工模拟高藻原水,当投加PDM：PAC质量比10%的复配混凝剂10 mg/L时,复配混凝剂对藻类的去除率为80.5%。     

新型混凝剂应用于中水处理的试验研究

围绕着中水回用过程中面临的若干关键问题,通过系统研究筛选高效混凝剂及优化混凝过程来提高污染物去除率,为中水回用提供经济合理的工艺途径.实验结果表明,与FeCl3相比,HPACS系列具有显著优越的除浊与除有机物性能.除磷性能则较为一致,可以达到90%以上的去除率.PFAC系列与FeCl3相比,除浊性能较差,取决于混凝剂中的有效成分的含量,但是具有较为优越的除有机物性能.HPAA系列具有显著优越的除浊和除有机物性能.HPFA与FeCl3系列相比,则具有较高的除磷效果,HPAA的除磷效果则相对较差.不同系列混凝剂具有不同的除浊、除有机物与除磷性能,需要结合分质供水的要求进行优化应用.     

氯化镁复配硫酸铝混凝性能及絮体特性

在研究氢氧化镁混凝特性的基础上,复配氯化镁和硫酸铝作为混凝剂,以高岭土配水水样为研究对象,运用iPDA在线监测技术对混凝过程絮体形成进行监测,探讨了单独使用氯化镁和硫酸铝以及二者复配使用的混凝效果和絮体特性,确定复配使用的各种条件。结果表明,对于浊度20 NTU,pH 11.5的高岭土配水水样,氯化镁、硫酸铝最佳投加量分别为7.2 mg/L(Mg2+计)和3 mg/L(Al3+计);硫酸铝跟氯化镁复配使用时,先投加硫酸铝,间隔30 s后投加氯化镁,混凝效果较好;在镁离子最佳投加量7.2 mg/L时,铝和镁最佳质量比在1∶3~1∶2之间;镁铝复配时其FI值明显大于单独作用时,即絮体尺寸大小:二者复配硫酸铝氯化镁,而且复配条件下Zeta电位值在零电势左右浮动,浮动范围小,更利于聚集沉淀;镁铝复配时发生了协同效应,弥补了单独使用氯化镁混凝过程的不足。     

Comparison of coagulation performance and floc properties of a novel zirconium-glycine complex coagulant with traditional coagulants

A new inorganic-organic hybrid material zirconium-glycine complex (ZGC) was firstly used as a coagulant in a coagulation process to treat Pearl River raw water. Its coagulation performance was compared with commonly used aluminum (Al) coagulants such as aluminum sulfate (Al₂(SO₄)₃) and polyaluminum chloride (PAC), in terms of water quality parameters and floc properties. ZGC coagulation achieved higher removal of turbidity (93.8 %) than other traditional coagulants. Charge neutralization was proven to act as a dominant mechanism during ZGC coagulation. The aggregated flocs with ZGC showed the fastest growth rate and good recovery ability compared with the other coagulants and achieved the largest floc size within 5 min. The ZGC coagulant can decrease the hydraulic retention time and increase removal efficiency.     

脱木素工艺处理造纸废水的实践与机理

脱木素工艺为中小制浆企业的黑液治理提供了新的方法。系统中酸化纤维污泥减小碱木素胶粒间的斥力 ,吸附废水中已析出的木质素和细小纤维 ;酸破坏了系统中胶体的水化膜 ,增大了胶体的粒径 ;混凝剂中和胶体表面电荷 ,增加颗粒间的接触机会 ,同时发挥了絮凝沉降的作用。该工艺与传统工艺相比 ,减少了酸及混凝剂的用量 ,木素沉降速度快。当试验废水pH =5、绝干纤维污泥与进水CODCr质量之比为 1.1、硫酸铝投加量为 160mg/L时 ,CODCr去除率高于 63 %。     

Removal of emulsified fuel oils from brackish and pond water by dissolved air flotation with and without polyelectrolyte use: pilot-scale investigation for estuarine and near shore applications

In coastal areas, estuaries, and inland waters, dispersant use after oil spills is not allowed due to sensitivity of the ecosystems. The purpose of this study was to investigate the removal of emulsified fuel oils from brackish and pond water by dissolved air flotation (DAF) with and without use of coagulants. Experiments were conducted with a 60 L DAF system. Fuel oil-water emulsions were prepared with regular unleaded gasoline, jet fuel, and diesel fuel mixed at 1:1:1 (v/v/v) ratio. Batch and continuous runs were conducted at air pressurization of 354.6 kPa. During both batch and continuous modes, significant petroleum hydrocarbon (PHC) removal was achieved within 10 min. Coagulant addition initially increased the PHC removal by about 5-15%. However, effectiveness of the coagulant was not significant after 20 min due to breakage of the aggregates. In general, the pond water had higher PHC removal than the brackish water. With longer run times, PHC removal improved slightly and the effluent contained increasing fractions of higher molecular weight compounds indicating that PHC removal was due to both DAF and stripping processes. Results indicate that DAF process can be effective both with and without the use of coagulants for removing PHCs from brackish and pond waters.     

废石粉渣制备混凝剂及其除浊净水效果研究

利用废石粉渣制备无机混凝剂,并研究所得初产品对硅藻土悬浮液和受污湖水样品进行处理的适宜操作条件以及除浊净水效果,结果表明,利用某些废石粉渣制备的混凝剂有较好效果,但制备工艺有待改善。     

Determination of optimum polymeric coagulant in palm oil mill effluent coagulation using multiple-objective optimisation on the basis of ratio analysis (MOORA)

The main limitation of a conventional palm oil mill effluent (POME) ponding system lies in its inability to completely decolourise effluent. Decolourisation of effluent is aesthetically and environmentally crucial. However, determination of the optimum process parameters is becoming more complex with the increase of the number of coagulants and responses. The primary objective of this study is to determine the optimum polymeric coagulant in the coagulation–flocculation process of palm oil mill effluent by considering all output responses, namely lignin–tannin, low molecular mass coloured compounds (LMMCC), chemical oxygen demand (COD), ammonia nitrogen (NH₃-N), pH and conductivity. Here, multiple-objective optimisation on the basis of ratio analysis (MOORA) is employed to discretely measure multiple response characteristics of five different types of coagulants as a function of assessment value. The optimum coagulant is determined based on the highest assessment value and was identified as QF25610 (cationic polyacrylamide). On the other hand, the lowest assessment value was represented by AN1800 (anionic polyacrylamide). This study highlights the simplicity of MOORA approach in handling various input and output parameters, and it may be useful in other wastewater treatment processes as well.