The effects of temperature and oxygen content on the PCDD/PCDFs formation in MSW fly ash

In this study, the effects of the temperature, oxygen content in the gas stream and carbon content in ash particles on PCDD/Fs formation on the fly ash surface were investigated. The optimum temperatures for dioxin formation were found at 350 degrees C for boiler ash, 300 degrees C for cyclone ash and 250 degrees C for ESP ash, respectively. Preliminary results indicate that the optimum temperature will decrease as the particle size decreases. When the O2 concentration is varied between 0% and 100%, the optimum oxygen content for PCDD/Fs formation is found to be at 7.5% for cyclone ash, and the PCDD/PCDF ratio increases with the increase of oxygen content. Dioxin formation is observed even for the gas containing no oxygen passed through the fly ash. Hence, other reacted routes that do not need O2 for dioxin formation take place on fly ash. The carbon content in fly ash is varied between 0% and 20% in this study, and the results have indicated that the maximum dioxin formation is to be found at 5%. The precursors are not injected into the fly ash or gas stream in all formation experiments, however, dioxin is still formed in fly ash. Consequently, other chlorinated routes besides Deacon reactions may take place on the fly ash surface.     

Effect of reaction time on PCDD and PCDF formation by de novo synthetic reactions under oxygen deficient and rich atmosphere

The effect of reaction time on formation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) was studied under laboratory conditions in the system containing municipal waste incineration fly ash, activated carbon and copper chloride dihydrate at 300 degrees C in 99.999% N2 and N2 + 10% O2 atmosphere. The concentrations of tetra- to octa-chlorinated isomers as well as I-TEQ concentrations of toxic congeners are reported. The mechanism of PCDD and PCDF formation from chlorophenols and chlorinated biphenyls is discussed in the light of the time changes of PCDD/PCDF ratios.     

Correlation of PCDD/PCDF and CO values in a MSW incinerator--indication of memory effects in the high temperature/cooling section

The correlation of PCDD/PCDF levels with the CO emissions in a full-scale municipal waste incinerator was assessed during a four-week measurement effort. PCDD/PCDF concentrations in fly ashes-containing more than 99% of the total PCDD/PCDF burden of the fluidized bed incinerator (FBI)-were measured and compared with the emitted CO concentrations. The CO concentration during the sampling time showed no significant correlation to the PCDD/ PCDF amount in fly ash (R2 = 0.078). However, a comparison of the time integrated CO concentration several hours before sampling lead to a correlation with the PCDD/PCDF burden. Maximum correlation was found for the time integrated CO values of 3 and 4 h before sampling (R2 = 0.467 and R2 = 0.457 respectively). This indicates a memory effect in the high temperature cooling section of several hours. Possible mechanisms leading to the memory effect are discussed. The correlation of PCDD/PCDF with CO concentration demonstrate that the combustion conditions play an important role for PCDD/PCDF formation in FBIs. However the variability in the correlation of CO to PCDD/PCDF levels show that other factors have a significant influence on PCDD/PCDF formation.     

Influence of temperature on PCDD/PCDF desorption from waste incineration flyash under nitrogen

A municipal solid waste incinerator flyash was heated to between 200 and 400 degrees C under nitrogen in a bench-scale, static bed reactor for 4 days soak time. The influence of temperature on the levels of PCDD and PCDF remaining in and desorbed from the ash were investigated using GC-MS/MS. PCDD and especially PCDF formation was seen on the flyash between 225 and 300 degrees C. Large increases in the I-TEQ of the treated ash relative to the increase in its overall PCDD/PCDF content indicated that the formation of 2378-substituted congeners was favoured over that of other substitution patterns. In the absence of a source of gaseous oxygen, formation was mainly attributed to de novo reactions involving solid phase oxygen. Dechlorination of the PCDD/PCDF in flyash became increasingly important above 275 degrees C. Maximum desorption was seen at 325 degrees C, with the equivalent of 35 wt% of the PCDD/F in the original flyash being recovered from the exhaust traps at this temperature. The desorbed species were mainly M(1)CDD/CDDF-T(3)CDD/CDDF resulting from dechlorination of higher chlorinated PCDD/PCDF, with consequently low I-TEQ values.     

A simple kinetic model of PCDD/F formation by de novo synthesis

A simple fixed-bed reactor model is used to describe experimental data about the formation of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) from fly ash carbon. The heterogeneous oxidation of graphite-like carbon is represented by a reaction which is first order in carbon and one half order in oxygen. The same orders of reaction are assumed to be valid for PCDD/F formation, such that the oxidation of fly ash carbon would have three parallel channels leading to COx, PCDD and PCDF. In addition, PCDD/F degradation by oxygen is considered and appropriate rate constants were fitted to simulate the experimental data. The effects of water vapour and particulate copper on PCDD/F formation are included. As a result, an overall kinetic model of PCDD/F formation is obtained which describes most of the experimental data with reasonable accuracy. The main reaction channel, COx formation, needs to be understood more completely, in order to interpret PCDD/F reaction pathways better. The model can be extended to include other chlorinated aromatics and the gas/particle partitioning of the semivolatiles. It provides a basis for the qualitative and quantitative interpretation of fixed-bed and flow reactor results and it is hoped to be applicable to industrial installations like waste incinerators and metal smelters.     

Formation of polychlorinated dibenzo-p-dioxins/dibenzofurans from residual carbon on municipal solid waste incinerator fly ash using Na37Cl

Na37Cl was used to study the role of chlorine in the formation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) from carbon. Adding Na37Cl to fly ash showed that this compound was a (relatively) poor chloride source; chlorine naturally present on the ash - which could include both chlorine in residual carbon and (metal) chlorides - was found to be ca. 17x more reactive. When both Na37Cl and CuCl2 were added to aqueous extracted fly ash, the percentage of 37Cl from Na37Cl included in PCDD/F increased, compared to the combination of Na37Cl/fly ash. When Na37Cl and CuCl2 were exchanged in water, followed by evaporation of the solvent, and mixed with aqueous extracted fly ash, the percentage of 37Cl included in PCDD/F was much higher. Apparently, direct transfer of 37Cl from CuCl2 to carbon and PCDD/F was much faster than transfer of 37Cl- from Na37Cl via a metal chloride (such as CuCl2) to carbon and PCDD/F. In addition to chlorine in PCDD/F originating from exchanged NaCl/CuCl2, chloride left on the fly ash after aqueous extraction and chlorine present in residual carbon could also have been incorporated in PCDD/F.     

Characterization of residual carbon influencing on de novo synthesis of PCDD/Fs in MSWI fly ash

Using 19 samples of fly ash collected from various MSW incineration facilities, residual carbon was characterized by gasifiable fraction at 450 degrees C (C450), and the correlations with de novo synthesis of PCDD/Fs were experimentally examined. Fly ashes were classified into three groups by the ratio of C450 to total residual carbon. By comparison of CO and CO2 generation patterns with those of reference materials, unburnt carbon of solid waste and activated carbon powder injected into flue gas were identified as a carbon source in fly ash. In the experiment of de novo synthesis of PCDD/Fs, the content of PCDD/F synthesis depended on C450 regardless of the origin of carbon. In addition, the model to predict the content of PCDD/F synthesis, DeltaPCDD/F=0.989.Cu.C450, fitted well with experimental values.     

Reactions of 2,4,6-trichlorophenol on model fly ash: oxidation to CO and CO2, condensation to PCDD/F and conversion into related compounds

Thermal treatment of 2,4,6-trichlorophenol on a magnesium silicate-based model fly ash in the temperature range between 250 degrees C and 400 degrees C leads predominantly to carbon monoxide and carbon dioxide. The fraction of 2,4,6-trichlorophenol which is oxidized to CO and CO2 increases from 3% at 250 degrees C to 75% at 400 degrees C. Further products are polychlorinated benzenes, dibenzo-p-dioxins, dibenzofurans and phenols. The homologue and isomer patterns of the chlorobenzenes suggest chlorination in the ipso-position of the trichlorophenol. The formation of PCDD from 2,4,6-trichlorophenol and 2,3,4,6-tetrachlorophenol on municipal solid waste incinerator fly ashes and model fly ash were compared and the reaction order calculated.     

The formation and emission of dioxins in large scale thermal processes

The paper assesses extensive data of PCDD/F measurements on flue gas emissions from thermal processes, including, e.g. municipal solid waste incinerators (MSWIs), combustors of wood and industrial waste, coal fired powerplants and boilers, ferro and non-ferro processes. Numerous investigators have conducted laboratory experiments to assess the formation mechanisms of PCDD/F. The results, obtained from fixed-bed experiments, have been critically evaluated and indicate that de novo synthesis is the dominant mechanism in actual thermal processes where conditions that favour the precursor formation are not experienced. The analysis of PCDD/F profiles from the large scale thermal processes in general, and MSWIs in particular, supports the dominant role of the de novo synthesis, irrespective of the type of thermal process considered. The PCDF/PCDD ratio exceeds 1 and the degree of chlorination points towards the dominant presence of HpCDD and OCDD within the dioxin group, and of PeCDF, HxCDF and HpCDF within the furan group. Since real-time measurement of PCDD/F is impossible, the correlation of PCDD/F emissions with operating parameters and/or emission levels of other more easily measured pollutants could be a tool in predicting the PCDD/F formation levels. Data of Flemish MSWIs were used to statistically assess such correlations. From an evaluation of the data at a given operating temperature, misleading conclusions can be drawn. Only the effect of temperature is evident. After converting all data at a reference temperature of, e.g. 230 degrees C, PCDD/F concentrations achieve nearly constant values, irrespective of the values of other parameters, thus stressing that the major controlling parameter for the PCDD/F emission is the temperature of the ESP. The PCDD/F concentrations increase with temperature in the range up to 280 degrees C. The ESP temperature should be kept preferably between 180 degrees C and 200 degrees C, where de novo synthesis is reduced and where PCDD/Fs are increasingly adsorbed on the fly ash, in line with the standard temperature dependence of adsorption isotherms.     

Effects of oxygen on formation of PCB and PCDD/F on extracted fly ash in the presence of carbon and cupric salt

The effect of oxygen-nitrogen atmosphere (N2 + 10%O2, N2 + 1%O2 and 99.999% N2) on the formation of PCB, PCDD and PCDF by the de novo synthetic reactions in the system consisting of extracted fly ash (from municipal waste incinerators--MWI), activated carbon, CuCl2 x 2H2O and NaCl at 340 degrees C was studied. The content of PCDD/F for systems with 10%O2, 1%O2 and 99.999% N2 was decreasing and corresponded to 17,304, 5544, and 1437 ng/sample. In all studied systems the isomer OCDD/F was prevailing. The content of PCBs in the same system was also decreasing from 1214 to 166 ng/g. Formation of nonortho PCB was relatively high compared to the system where only nitrogen was present. The possible mechanism of formation is outlined.     

Influence of residual carbon on the decomposition process of PCDD/Fs in MSWI fly ash

In heating treatment of fly ash to reduce PCDD/Fs, cooling process is important to inhibit de novo formation of PCDD/Fs. In this study, assuming that residual carbon is the dominant factor of de novo synthesis, the relation between PCDD/Fs and residual carbon was examined. Firstly, by using MSWI fly ash which was treated in an actually operated facility, both the content of PCDD/Fs and residual carbon were decreased as heating temperature increased. At temperatures higher than 400 degrees C, the reduction rate of residual carbon was higher than 20% and more than 95% of PCDD/Fs was decomposed. In order to simulate a heating treatment process, fly ash was heated at different temperatures and gas atmospheres, oxygen or nitrogen. Heated fly ash was placed for 2 h at 300 degrees C in oxygen to promote de novo synthesis, or cooled immediately. As a result, good correlation between PCDD/Fs and residual carbon was found, therefore it was shown experimentally that residual carbon was the main factor for PCDD/Fs formation by de novo synthesis in fly ash.     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

Effects of selected metal oxides on the dechlorination and destruction of PCDD and PCDF

OCDD and OCDF spiked silica/graphite based model fly ash containing various copper compounds and metal oxides were thermally treated under oxygen deficient conditions. All copper compounds tested showed a considerable dechlorination/hydrogenation reaction at 260 °C. After 30 min at 340 °C, less than 1% of the spiked OCDD and OCDF was recovered as T₄CDD/F to OCDD/F. Other compounds tested demonstrated a lower rate of dechlorination compared to the copper compounds. However, all other metal oxides showed a small dechlorination effect at 260 °C, which was considerably increased at 340 °C.

The model fly ash containing the different copper compounds or metal oxides showed comparable PCDD and PCDF isomer patterns after thermal treatment. However, small differences were observed among the different tested compounds. The PCDD and PCDF isomer patterns on the model fly ashes were similar to patterns found during dechlorination experiments on fly ashes from waste incineration processes.

Model fly ash containing Ca(OH)₂ exhibited the highest destruction potential, but a low dechlorination potential. In contrast, model fly ash containing any of the remaining compounds tested, was found to predominantly dechlorinate the spiked OCDD and OCDF.     

The behavior of PCDD and PCDF during thermal treatment of waste incineration ash

The polychlorinated dibenzo-p-dioxin (PCDD) and polychlorinated dibenzofuran (PCDF) content of three fly ash samples with different elemental compositions from different municipal waste incinerators were analyzed before and after thermal treatment at 300 °C or 500 °C. Gas phase emissions during the treatments were also collected and analyzed. Substantial reductions in the total PCCD/F content of the ashes were observed after treatment at 500 °C, seemingly due to degradation rather than dechlorination. Treatment at 300 °C resulted in an increase in the PCDD/F content of the three ashes. Initial concentration of PCDD/F in the untreated ashes did not reflect the outcome of the treatment at the different temperatures. In addition, the composition of the ash was found to influence the rate of decomposition and formation of PCDD and PCDF during thermal treatment; the results showed that Cu, Fe, Ca and S play important roles in these processes.     

Determination of polychlorinated dibenzo-p-dioxins and dibenzo-furans in solid residues from wood combustion by HRGC/HRMS

PCDD/PCDF were determined in solid samples from wood combustion. The samples included grate ashes, bottom ashes, furnace ashes as well as fly and cyclone ashes. The solid waste samples were classified into bottom and fly ash from native wood and bottom and fly ash from waste wood. For each of the four classes concentration distribution patterns from individual congeners, the sums of PCDD/PCDF and the international toxicity equivalents (I-TEQ) values are given. The I-TEQ levels of fly ash from waste wood burning can be approximately up to two thousand times higher than the values from fly ashes of natural wood. The I-TEQ levels in bottom ashes from waste wood combustion systems are as low as the corresponding ashes from the combustion of native wood. Grate ash samples from waste wood combustion systems with low carbon burnout show high levels of PCDD/PCDF.     

Modeling the formation of PCDD/F in solid waste incinerators

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/F) appear in unacceptable amounts in the gaseous emissions during the incineration of wastes containing significant quantities of chlorine and metals, such as MSW and medical waste. They are formed both in the gas phase at temperatures above 600 degrees C and on the surface of the solid phase (flyash) in the temperature range 400-225 degrees C. Both the precursor (from existing smaller chlorinated molecules) and de novo (from elemental carbon) routes are involved. An empirically derived global model for their de novo formation on flyash in MSW and medical waste incinerators has now been extended to include the precursor mechanism, and a gas phase formation component, with separate rate expressions for PCDD and PCDF. Homogeneous PCDD formation is governed by the concentration of chlorophenols and PCDF by that of chlorophenols and chlorobenzenes. The result is more complete system which distinguishes between the gas and solid phase contributions to the I-TEQ. An additional step for the adsorption of gaseous PCDD/F back onto the solid phase during cooling suggests this should be minimal in the gas ducts of an incinerator. The extended model has been tested against experimental data collected from a well-controlled pilot incinerator and commercial incinerators, and found to adequately describe the measured outputs. With the model it should be possible to predict the PCDD/F emissions from commercial incinerators, provided that the ash properties and the overall temperature-time profiles are known.     

Formation and destruction of PCDD/F inside a grate furnace

Formation and destruction of polychlorinated dibenzo-p-dioxins and dibenzofurans PCDD/F during the combustion process was investigated experimentally in a pilot plant. All important process steps like the burnout of the fuel bed on the grate, the burnout of the flue gas inside the combustion chamber, the heat recovery in a boiler as well as influences of the fuel composition are described in detail.

High concentrations especially of PCDF are formed during the burnout of the fuel bed. The formation reaction is mainly influenced by the fuel composition and the burnout characteristic of the fuel bed. Fuels with low chlorine and low metal content (Cu) result only in negligible concentrations of PCDD/F.

Under stable combustion conditions characterized by an excellent flue gas burnout PCDD/F will almost be completely destroyed already inside the combustion chamber. “Cold strands” of unburned flue gas (high CO concentrations) caused by disturbed combustion conditions will result in high concentrations of PCDD and especially of PCDF in the raw gas.

A second place of PCDD/F formation is the well-known boiler section. Here fly ash deposits containing residual carbon (mainly soot particles) are the source for the formation reaction. Under stationary effective combustion conditions, they are dominant for PCDD/F concentrations in the raw gas over a very long period of time.

Stationary efficient flue gas burnout (especially soot) together with effective boiler cleaning will guaranty low concentrations of PCDD/F in the flue gas in front of the flue gas cleaning system.     

Changes in PCDD/PCDF formation processes during instationary phases of combustor operation--exemplified by the use of Cl4DD isomer patterns

In this paper results of various measurement campaigns at different municipal waste incineration (MWI) plants concerning the change of the PCDD/PCDF isomer distribution in the crude gas during transiently impaired combustion conditions are presented. The focus is on the Cl4DD isomer distributions exemplarily for all other homologue groups to demonstrate the change in PCDD/PCDF formation mechanism at transient combustion conditions. Additionally to crude gas samples, at one plant filter and boiler ash were investigated simultaneously to determine if there is any difference in the isomer distribution between the matrices. For the ash from an electrostatic precipitator (ESP ash), the boiler ash and the corresponding crude gas sample, nearly identical changes in the Cl4DD isomer distribution under transient combustion conditions in relation to the normal operation process could be detected. By comparing the Cl4DD isomer distributions from different incineration plants (two municipal waste incinerators and one little incinerator burning wood chips for heating domestic household) under transient combustion conditions, in all cases the 1,3,6,8- and 1,3,7,9-Cl4DD were dominating the isomer distribution, whereas under normal operation other isomers were predominant. Obviously PCDD/PCDF formation mechanisms under transient combustion conditions are independent from the type of incinerator and of the burned fuel, respectively. Data sets were analyzed with respect to the possible reaction mechanism via chlorophenols and a good correlation of 2,4,6-trichlorophenol during the second phase of a start-up process and during a CO experiment was found. To get more detailed information about possible formation mechanisms, at one plant the dependence of the PCDD/PCDF isomer distribution on the different matrices was studied. Separate analysis of fly ash collected at the boiler exit, subsequent gas phase, ESP ash and boiler ash under normal operation conditions showed that, apart from the fly ash, the Cl4DD isomer distributions are nearly the same in the different matrices. Surprisingly, the Cl4DD isomer distribution of the fly ash was more similar to the distributions found under transient combustion conditions.     

Dechlorination and destruction of PCDD,PCDF and PCB on selected fly ash from municipal waste incineration

The potential of fly ash to dechlorinate and destroy PCDD, PCDF and PCB was tested under oxygen deficient conditions in the laboratory. Specifically, two types of fly ash were compared, originating either from a fluidized bed incinerator using Ca(OH)₂ spray (FA1), or a stoker incinerator without Ca(OH)₂ impact (FA2).

Results from the present study indicate that on FA2 type fly ash, the degradation processes of OCDD, OCDF and D₁₀CB occurred primarily via dechlorination/hydrogenation up to temperature settings of 340 °C. In contrast, FA1 type fly ash was found to effect both dechlorination and destruction of these compounds already at temperature settings of 260 °C.

The dechlorination velocity of PCDD and PCDF did not differ significantly. However, the first dechlorination step of OCDF in the 1,9-position occurred faster compared to the first dechlorination step of OCDD.

The isomer pattern resulting from the dechlorination processes was quite similar on both FA1 and FA2, indicating that differences in alkalinity or elemental composition of the two types of fly ashes do not have a significant influence on the position of dechlorination. PCDD and PCDF dechlorination of the 2,3,7,8-positions was not favoured over dechlorination of the 1,4,6,9-positions on either type of fly ash. In contrast, dechlorination of PCB occurred predominantly on the toxicological relevant 3- and 4-positions.

The dechlorination/destruction processes were completed on both types of fly ash at 380 °C within one hour, which correlates well with results obtained from actual plant operation practices.     

Dechlorination of polychlorinated biphenyls, dibenzo-p-dioxins and dibenzofurans on fly ash

Dechlorination of commercial mixtures of polychlorinated biphenyls (PCB) as well as polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) on extracted and non-extracted fly ash obtained from municipal waste incinerator (MWI) was studied in closed systems under nitrogen atmosphere at temperatures of 260°C and 340°C. Decomposition results (given as the difference between PCB or PCDD/F molar amounts before and after the experiment (in %) due predominantly to dechlorination reactions) and detoxification data (expressed similarly but related to toxic PCB and PCDD/F congeners only and given in I-TEQ units) are reported. Detoxification of Delor 105/80T at 260°C and 340°C at a loading of 0.65 wt% was 99.48% and 100%, respectively. The decomposition of Delor 103 at 340°C and for the loading of 0.75 wt% corresponded to 99.99%. The detoxification capability of PCDD/Fs on extracted and non-extracted fly ash for loading of 130 and 264 ng/0.4 g of fly ash at 340°C made 96 and 98%, respectively.