Study of fuel oxygenates solubility in aqueous media as a function of temperature and tert-butyl alcohol concentration

Methyl tert-butyl ether (MTBE) is the most widely used oxygenate in gasoline blending and has become one of the world’s most widespread groundwater and surface water pollutants. Alternative oxygenates to MTBE, namely ethyl tert-butyl ether (ETBE), tert-amyl ether (TAME) and diisopropyl ether (DIPE) have been hardly studied yet. The solubility of these chemicals is a key thermodynamic information for the assessment of the fate and transport of these pollutants. This work reports experimental data of water solubility at the range from 278.15 to 313.15 K and atmospheric pressure of ethers used in fuels (MTBE, ETBE, TAME and DIPE) due to the strong influence of temperature on its trend. From the experimental data, temperature dependent polynomials were fitted, thermodynamic parameters were calculated and theoretical models were used for prediction. Finally, the tert-butyl alcohol (TBA) influence in the solubility of MTBE and ETBE in aqueous media was studied.     

Accurate Chemical Analysis of MTBE in Environmental Media

The new millennium ushers in changes for refiners of automobile gasoline in the United States, as well as for the state and federal regulators who establish guidelines for gasoline formulation and environmental regulation governing the fate of gasoline-related chemicals in the nation's air, soil and groundwater. One current issue in the gasoline formulation debate centers on the comparison of the proven benefits of the addition of chemical oxygenates—especially methyltert -butyl ether (MTBE)—to gasoline (to improve tailpipe emission quality) against the presumed environmental problems caused by the presence of oxygenates in ground- and surface waters due to fugitive releases of gasoline. Credible debate on this subject presumes that current and past environmental monitoring data for MTBE in environmental samples is accurate and precise. Experience suggests that this assumption is not correct, in part because certain analytical methodologies—particularly older methods supported by the U.S. Environmental Protection Agency—can fall short of reasonable data quality goals for measurement of MTBE. This Technical Note summarizes the standard EPA methods available to site investigators who need to measure MTBE in environmental media, the limitations and advantages of these measurement techniques, and recommendations for improving these standard EPA methods to yield the highest quality MTBE environmental residue data.     

甲基叔丁基醚的污染治理技术研究进展

甲基叔丁基醚(MTBE)是一种无铅汽油添加剂,其广泛使用造成了土壤和地下水污染;同时对人类有可疑致癌作用,因此成为人们关注的焦点.对近年来国外MTBE的污染治理技术研究进展进行了综述,并对主要方法进行了对比.在适宜的微生物存在条件下,MTBE的生物降解是可以发生的;植物修复技术可用于地下水和土壤污染治理;物理化学方法种类繁多,包括吸附和高级氧化等,其处理效率高成本也较高;新的处理技术如渗透性活性障壁PRB、膜分离/催化技术等也在研究之中.     

Microbial degradation of methyl tert-butyl ether and tert-butyl alcohol in the subsurface

The fate of fuel oxygenates such as methyl tert-butyl ether (MTBE) in the subsurface is governed by their degradability under various redox conditions. The key intermediate in degradation of MTBE and ethyl tert-butyl ether (ETBE) is tert-butyl alcohol (TBA) which was often found as accumulating intermediate or dead-end product in lab studies using microcosms or isolated cell suspensions. This review discusses in detail the thermodynamics of the degradation processes utilizing various terminal electron acceptors, and the aerobic degradation pathways of MTBE and TBA. It summarizes the present knowledge on MTBE and TBA degradation gained from either microcosm or pure culture studies and emphasizes the potential of compound-specific isotope analysis (CSIA) for identification and quantification of degradation processes of slowly biodegradable pollutants such as MTBE and TBA. Microcosm studies demonstrated that MTBE and TBA may be biodegradable under oxic and nearly all anoxic conditions, although results of various studies are often contradictory, which suggests that site-specific conditions are important parameters. So far, TBA degradation has not been shown under methanogenic conditions and it is currently widely accepted that TBA is a recalcitrant dead-end product of MTBE under these conditions. Reliable in situ degradation rates for MTBE and TBA under various geochemical conditions are not yet available. Furthermore, degradation pathways under anoxic conditions have not yet been elucidated. All pure cultures capable of MTBE or TBA degradation isolated so far use oxygen as terminal electron acceptor. In general, compared with hydrocarbons present in gasoline, fuel oxygenates biodegrade much slower, if at all. The presence of MTBE and related compounds in groundwater therefore frequently limits the use of in situ biodegradation as remediation option at gasoline-contaminated sites. Though degradation of MTBE and TBA in field studies has been reported under oxic conditions, there is hardly any evidence of substantial degradation in the absence of oxygen. The increasing availability of field data from CSIA will foster our understanding and may even allow the quantification of degradation of these recalcitrant compounds. Such information will help to elucidate the crucial factors of site-specific biogeochemical conditions that govern the capability of intrinsic oxygenate degradation.     

Oxygenated fuel induced cosolvent effects on the dissolution of polynuclear aromatic hydrocarbons from contaminated soil

The cosolvent-induced dissolution of polynuclear aromatic hydrocarbons (PAHs) from contaminated soil caused by oxygenated fuel spills was studied. Oxygenated fuel induces a solvent flushing effect on the contaminated soil due to the high content of oxygenated compounds (i.e., methanol, ethanol, and methyl tert butyl ether (MTBE)). The miscible displacement techniques were applied to evaluate the increased potential for secondary contamination in an impacted site. Significant solubility enhancement of the 18 PAHs monitored during fuel spill simulation and cosolvent flushing is clearly evident when compared to normal water dissolution. The breakthrough concentration profile for each PAH constituent was integrated over the cumulative effluent volume (i.e., the zeroth moment) to determine the total PAH mass removed during the experiment. The removal efficiency of PAHs ranges from 46.6% to 99.9% in three oxygenated fuels (i.e., M85, E85, and oxygenated gasoline) during the fuel spill. Several factors including hydrophobicity of compounds, nonequilibrium dissolution due to nonuniform coal tar distribution, and heterogeneous media properties affect the oxygenated compound-induced dissolution process. This study provides a basis to predict the facilitated transport of hydrophobic organic compounds from subsurface environment due to the cosolvent effects of oxygenated fuels.     

Water quality at five marinas in Lake Texoma as related to methyl tert-butyl ether (MTBE)

Water quality in five marinas on Lake Texoma, located on the Oklahoma and Texas border, was monitored between June 1999 and November 2000. Focus was to evaluate lake water associated with marinas for methyl tert-butyl ether (MTBE). Lake water was collected at locations identified as marina entrance, gasoline filling station, and boat dock. Occurrence of MTBE showed a direct seasonal trend with recreational boating activity at marina areas. There was a positive correlation with powerboat usage ratio, which was directly related to the gallons of gasoline sold. Sampling before and after the high boat use holiday weekends determined the apparent influence of powerboat activity on MTBE contamination. Boat dock locations were the most sensitive sites to MTBE contamination, possibly due to gasoline spillage during engine startup. The most common compound of the BTEX series found with MTBE was toluene and co-occurrence was most frequent at gasoline filling stations.     

Oxygenated gasoline release in the unsaturated zone - Part 1: Source zone behavior

Oxygenates present in gasoline, such as ethanol and MTBE, are a concern in subsurface contamination related to accidental spills. While gasoline hydrocarbon compounds have low solubility, MTBE and ethanol are more soluble, ethanol being completely miscible with water. Consequently, their fate in the subsurface is likely to differ from that of gasoline. To evaluate the fate of gasoline containing oxygenates following a release in the unsaturated zone shielded from rainfall/recharge, a controlled field test was performed at Canadian Forces Base Borden, in Ontario. 200L of a mixture composed of gasoline with 10% ethanol and 4.5% MTBE was released in the unsaturated zone, into a trench 20cm deep, about 32cm above the water table. Based on soil cores, most of the ethanol was retained in the source, above the capillary fringe, and remained there for more than 100 days. Ethanol partitioned from the gasoline to the unsaturated pore-water and was retained, despite the thin unsaturated zone at the site (~35cm from the top of the capillary fringe to ground surface). Due to its lower solubility, most of the MTBE remained within the NAPL as it infiltrated deeper into the unsaturated zone and accumulated with the gasoline on top of the depressed capillary fringe. Only minor changes in the distribution of ethanol were noted following oscillations in the water table. Two methods to estimate the capacity of the unsaturated zone to retain ethanol are explored. It is clear that conceptual models for sites impacted by ethanol-fuels must consider the unsaturated zone.     

Oxygenated gasoline release in the unsaturated zone, Part 2: Downgradient transport of ethanol and hydrocarbons

In the event of a gasoline spill containing oxygenated compounds such as ethanol and MTBE, it is important to consider the impacts these compounds might have on subsurface contamination. One of the main concerns commonly associated with ethanol is that it might decrease the biodegradation of aromatic hydrocarbon compounds, leading to an increase in the hydrocarbon dissolved plume lengths. The first part of this study (Part 1) showed that when gasoline containing ethanol infiltrates the unsaturated zone, ethanol is likely to partition to and be retained in the unsaturated zone pore water. In this study (Part 2), a controlled field test is combined with a two-dimensional laboratory test and three-dimensional numerical modelling to investigate how ethanol retention in the unsaturated zone affects the downgradient behaviour of ethanol and aromatic hydrocarbon compounds. Ethanol transport downgradient was extremely limited. The appearance of ethanol in downgradient wells was delayed and the concentrations were lower than would be expected based on equilibrium dissolution. Oscillations in the water table resulted in minor flushing of ethanol, but its effect could still be perceived as an increase in the groundwater concentrations downgradient from the source zone. Ethanol partitioning to the unsaturated zone pore water reduced its mass fraction within the NAPL thus reducing its anticipated impact on the fate of the hydrocarbon compounds. A conceptual numerical simulation indicated that the potential ethanol-induced increase in benzene plume length after 20 years could decrease from 136% to 40% when ethanol retention in the unsaturated zone is considered.     

Emission and fate assessment of methyl tertiary butyl ether in the Boston area airshed using a simple multimedia box model: comparison with urban air measurements

Expected urban air concentrations of the gasoline additive methyl tertiary butyl ether (MTBE) were calculated using volatile emissions estimates and screening transport models, and these predictions were compared with Boston, MA, area urban air measurements. The total volatile flux of MTBE into the Boston primary metropolitan statistical area (PMSA) airshed was calculated based on estimated automobile nontailpipe emissions and the Universal Quasi-Chemical Functional-Group Activity Coefficient computed abundance of MTBE in gasoline vapor. The fate of MTBE in the Boston PMSA was assessed using both the European Union System for the Evaluation of Substances, which is a steady-state multimedia box model, and a simple airshed box model. Both models were parameterized based on the meteorological conditions observed during air sampling in the Boston area. Measured average urban air concentrations of 0.1 and 1 microg/m3 MTBE during February and September of 2000, respectively, were comparable to corresponding model predictions of 0.3 and 1 microg/m3 and could be essentially explained from estimated temperature-dependent volatile emissions rates, observed average wind speed (the airshed flushing rate), and reaction with ambient tropospheric hydroxyl radical (*OH), within model uncertainty. These findings support the proposition that one can estimate gasoline component source fluxes and use simple multimedia models to screen the potential impact of future proposed gasoline additives on urban airsheds.     

Using the Gasoline Additive MTBE in Forensic Environmental Investigations

A variety of additives are used in gasoline, and they can sometimes be used to help identify the source, timing, or number of gasoline spills at a site. The physicochemical characteristics of the additive MTBE, and its historical use pattern in the United States since 1979, make it a key compound to study when conducting forensic investigations of gasoline spills. MTBE's low octanol: water distribution coefficient and high solubility cause it to dissolve into groundwater more readily than other gasoline components. Thus, the initial appearance of MTBE in the groundwater is often a good indicator of a recent gasoline spill. MTBE's very low retardation and minimal biodegradation in groundwater can be used with transport rate calculations to establish relatively accurate estimates of spill timing. Because MTBE moves faster in groundwater than BTEX compounds, if a gasoline spill site has a BTEX plume that is longer than the MTBE plume, it is certain that at least two distinctly different gasoline releases have occurred. This allows for the identification of new gasoline spills, even when substantial subsurface petroleum contamination already exists. An example application is reviewed to demonstrate the use of MTBE data in forensic investigations.     

MTBE—Panacea or Problem

Methyl tert -butyl ether (MTBE) is an octane-enhancer and oxygenate compound that was authorized as a gasoline additive by the U.S. Environmental Protection Agency (USEPA) in late 1979. MTBE has many chemical and physical properties that make it a desirable compound for these purposes. However, the aqueous solubility of MTBE, which is in the 50,000 ppm range, allows it to dissolve into groundwater where it is transported virtually without retardation. MTBE also is resistant to microbial degradation and does not air-strip from water efficiently. These characteristics have caused wells to become contaminated with MTBE that in the absence would not have become contaminated with hydrocarbons from gasoline releases. Research on innovative technologies to treat water contaminated with MTBE is underway. The final regulatory determination of allowable concentrations and whether or not future use of MTBE will be allowed has yet to be made.     

Partitioning studies of coal-tar constituents in a two-phase contaminated ground-water system

Organic compounds derived from coal-tar wastes in a contaminated aquifer in St. Louis Park, Minnesota, were identified, and their partition coefficients between the tar phase and aqueous phase were determined and compared with the corresponding n-octanol/water partition coefficients. Coal tar contains numerous polycyclic aromatic compounds, many of which are suspected carcinogens or mutagens. Groundwater contamination by these toxic compounds may pose an environmental health hazard in nearby public water-supply wells. Fluid samples from this aquifer developed two phases upon settling: an upper aqueous phase, and a lower oily-tar phase. After separating the phases, polycyclic aromatic compounds in each phase were isolated using complexation with N-methyl-2-pyrrolidone and identified by fused-silica capillary gas chromatography/mass spectrometry. Thirty-one of the polycyclic aromatic compounds were chosen for further study from four different classes: 12 polycyclic aromatic hydrocarbons, 10 nitrogen heterocycles, 5 sulfur heterocycles, and 4 oxygen heterocycles. Within each compound class, the tar/water partition coefficients of these compounds were reasonably comparable with the respective n-octanol/water partition coefficient.     

Determination of MTBE in a recreational harbor using solid-phase microextraction

Discovery of the fuel additive methyl tert-butyl ether (MTBE) in groundwater, surface water, and stormwater has prompted studies of its sources, transport and fate. More limited data, however, is available on the extent of contamination of coastal waters, as well as the persistence of MTBE in the marine environment. We apply here the combination of solid phase microextraction and gas chromatography-mass spectrometry to the detection of sub-to-low microgram/l concentrations of MTBE in seawater samples. Analysis of samples collected at the Marina del Rey harbor, a shallow recreational harbor near Los Angeles, CA, show MTBE contamination in the low microgram/l level. MTBE measurements were made at different depths, from the surface to the bottom, at five sites within the harbor during months showing no measurable precipitation. The highest concentration of MTBE (18 microgram/l) was found at the boat launching ramp, and the lowest (0.2 microgram/l) near the harbor entrance, approximately 2.3 km from the ramp. The levels of MTBE measured, as well as their variation over the study period, are fully consistent with recreational boating as the primary source of contamination. No evidence for MTBE contamination from the adjacent stormwater control channel was noted.     

Using the Gasoline Additive MTBE in Forensic Environmental Investigations

A variety of additives are used in gasoline, and they can sometimes be used to help identify the source, timing, or number of gasoline spills at a site. The physicochemical characteristics of the additive MTBE, and its historical use pattern in the United States since 1979, make it a key compound to study when conducting forensic investigations of gasoline spills. MTBE's low octanol : water distribution coefficient and high solubility cause it to dissolve into groundwater more readily than other gasoline components. Thus, the initial appearance of MTBE in the groundwater is often a good indicator of a recent gasoline spill. MTBE's very low retardation and minimal biodegradation in groundwater can be used with transport rate calculations to establish relatively accurate estimates of spill timing. Because MTBE moves faster in groundwater than BTEX compounds, if a gasoline spill site has a BTEX plume that is longer than the MTBE plume, it is certain that at least two distinctly different gasoline releases have occurred. This allows for the identification of new gasoline spills, even when substantial subsurface petroleum contamination already exists. An example application is reviewed to demonstrate the use of MTBE data in forensic investigations.     

Partitioning of aromatic and oxygenated constituents into water from regular and ethanol-blended gasolines

Variability in gasoline-water partitioning of major aromatic constituents (benzene, toluene, ethylbenzene, and xylenes (BTEX)) and methyl tert-butyl ether (MTBE) were examined for regular and ethanol-blended gasolines. By use of a two-phase liquid-liquid equilibrium model, the distribution of nonpolar solutes between fuel phase and water was related to principles of equilibrium. The models derived using Raoult's law convention for activity coefficients and liquid solubility is presented. The observed inverse log-log linear dependence of K_fw values on aqueous solubility, could be well predicted by assuming gasoline to be an ideal solvent mixture. Oxygenated additives (i.e., ethanol and MTBE), in the low percent range (below 5%), were shown to have minimal or negligible cosolvent effects on hydrocarbon partitioning. In the case of high fuel-to-water ratio (e.g., 1:1) or near contaminant source zone, the cosolvent effect of oxygenated gasoline with high content of ethanol (e.g., E85) will be environmentally significant.     

Emission and Fate Assessment of Methyl Tertiary Butyl Ether in the Boston Area Airshed Using a Simple Multimedia Box Model: Comparison with Urban Air Measurements

Abstract

Expected urban air concentrations of the gasoline additive methyl tertiary butyl ether (MTBE) were calculated using volatile emissions estimates and screening transport models, and these predictions were compared with Boston, MA, area urban air measurements. The total volatile flux of MTBE into the Boston primary metropolitan statistical area (PMSA) airshed was calculated based on estimated automobile nontailpipe emissions and the Universal Quasi-Chemical Functional-Group Activity Coefficient computed abundance of MTBE in gasoline vapor. The fate of MTBE in the Boston PMSA was assessed using both the European Union System for the Evaluation of Substances, which is a steady-state multimedia box model, and a simple airshed box model. Both models were parameterized based on the meteorological conditions observed during air sampling in the Boston area. Measured average urban air concentrations of 0.1 and 1 [H9262]g/m³ MTBE during February and September of 2000, respectively, were comparable to corresponding model predictions of 0.3 and 1 μg/m³ and could be essentially explained from estimated temperature-dependent volatile emissions rates, observed average wind speed (the airshed flushing rate), and reaction with ambient tropospheric hydroxyl radical (.OH), within model uncertainty. These findings support the proposition that one can estimate gasoline component source fluxes and use simple multimedia models to screen the potential impact of future proposed gasoline additives on urban airsheds.     

甲基叔丁基醚(MTBE)对环境的污染及其对我国汽油生产的影响

本文简要介绍了汽油添加剂MTBE对环境的污染及减少MTBE污染机理研究的进展 ,同时介绍了对我国汽油生产的影响     

Effect of gasoline formulation on the formation of photosmog: a box model study

Based on exhaust gas analyses from the combustion of five different types of gasoline in a passenger car operated on a chassis dynamometer, box model simulations of the irradiation of exhaust/NOx/air mixtures using an established chemical mechanism for a standardized photosmog scenario were performed. The fuel matrix used covered wide fractional ranges for paraffinic, olefinic, and aromatic hydrocarbons. Two fuels also contained methyl tertiary butyl ether (MTBE). The different O3 profiles calculated for each run were compared and interpreted. The O3 levels obtained were strongly influenced by the exhaust gas concentrations of aromatic and olefinic hydrocarbons. The higher exhaust content of these compounds caused higher O3 production in the smog system investigated. The conclusion of the present study is that the composition of gasoline cannot be taken directly for the estimation of the emissions' O3 creation potential from its combustion. Variation of the dilution in the different calculations showed evidence for an additional influence of transport effects. Accordingly, further detailed exhaust gas analyses followed by more complex modeling studies are necessary for a proper characterization of the relationship between fuel blend and gasoline combustion products.     

Methyl tertiary hexyl ether and methyl tertiary octyl ether as gasoline oxygenates: assessing risks from atmospheric dispersion and deposition

Methyl tertiary hexyl ether (MtHxE) and methyl tertiary octyl ether (MtOcE) are currently being developed as replacement oxygenates for methyl tertiary butyl ether (MtBE) in gasoline. As was the case with MtBE, the introduction of these ethers into fuel supplies guarantees their introduction into the environment as well. In this study, a screening-level risk assessment was performed by comparing predicted environmental concentrations (PEC) of these ethers to concentrations that might cause adverse effects to humans or ecosystems. A simple box model that has successfully estimated urban air concentrations of MtBE was adapted to predict atmospheric concentrations of MtHxE and MtOcE. Expected atmospheric concentrations of these ethers were also estimated using the European Union System for the Evaluation of Substances (EUSES) multimedia fate model, which simultaneously calculates PECs in the various environmental compartments of air, water, soil, and sediment. Because little or no data are available on the physicochemical, environmental, and toxicological properties of MtHxE and MtOcE, estimation methods were used in conjunction with EUSES to predict both the PECs and the concentrations at which these ethers might pose a threat. The results suggest that these ethers would contaminate the air of a moderately sized U.S. city (Boston, MA) at levels similar to those found previously for MtBE. The risk assessment module in EUSES predicted risk characterization ratios of 10(-3) and 10(-2) for MtHxE and MtOcE, respectively, in Boston, and 10(-2) and 10(-1) in very large urban centers, suggesting that these ethers pose only a minimal threat to ecosystems at the anticipated environmental concentrations. The assessment also indicates that these compounds are possible human carcinogens and that they may be present in urban air at concentrations that pose an unacceptable cancer risk. Therefore, testing of the toxicological properties of these compounds is recommended before they replace MtBE in gasoline.     

颗粒活性炭去除水中甲基叔丁基醚的可行性研究

随着甲基叔丁基醚（MTBE）作为汽油添加剂被持续大量使用,其已成为一种地下水中常见的有机污染物。本文通过纯净水、自来水和地下水中MTBE的平衡吸附容量和微型快速穿透实验（MCRB）,比较了5种不同种类活性炭对MTBE的吸附性能。结果显示,苯酚值可准确预测活性炭样品对MTBE的平衡吸附容量大小次序,而丹宁酸值则可大致估计活性炭在实际处理应用时的吸附速度和吸附容量利用率。水样中共存的有机成分降低了活性炭对纯净水中MTBE的吸附容量,在背景TOC较低的去离子水中,活性炭对于MTBE的吸附性能反而比在地下水中降低得更多。穿透实验数据显示双柱串联的处理方式是高效应用活性炭吸附水中MTBE的优选工艺。使用环境友好的竹质活性炭去除地下水中MTBE具有良好的可行性和较高的性价比。